Compact circularly polarized beam‐switching wireless power transfer system for ambient energy harvesting applications

In this work, we propose a circularly polarized (CP) beam‐switching wireless power transfer system for ambient energy harvesting applications operating at 2.4 GHz. Beam‐switching is achieved using a low profile, electrically small CP antenna array with four elements and a novel miniaturized 4× 4 butler matrix. The CP antenna is designed with an e‐shaped slot and four antennas. The CP antenna measures 0.32 λ₀× 0.32 λ₀× 0.006 λ₀ at 2.4 GHz. The antenna has a gain of 3 dBic and an axial ratio less than 3‐dB at 2.4 GHz. A linear antenna array consisting of four elements is designed with the CP antenna element with an inter‐element distance of 0.29 λ₀ . A 4× 4 butler matrix with miniaturized couplers and crossovers are used to feed the four antenna array elements. Based on the input port of excitation, the main beam of the antenna array is demonstrated to be switched to four directions: ?5°, 65°, ?55°, and 20°. A CP rectenna is used to demonstrate the wireless power transfer capability of the combination of the butler matrix and the CP‐antenna array. The rectenna consists of a Teo‐shaped CP antenna and a rectifier. The open circuit voltage at the output of the rectenna is found to peak value of 30 mV at ?3°, 61°, ?53°, and 17°. Thus a complete system for CP wireless power transfer including the power transmission system as well as the RF energy harvesting sensor is designed and experimentally verified.     

A high‐gain compact circularly polarized microstrip array antenna with simplified feed network

A broadband high‐gain circularly polarized (CP) microstrip antenna operating in X band is proposed. The circular polarization property is achieved by rotating four narrow band linearly polarized (LP) microstrip patch elements in sequence. Since the conventional series‐parallel feed network is not conducive to the miniaturization of the array, a corresponding simplified feed network is designed to realize the four‐way equal power division and sequential 90° phase shift. With this feed network, the impedance bandwidth (IBW) of the CP array is greatly improved compared with that of the LP element, while maintaining a miniaturized size. Then, parasitic patches are introduced to enhance the axial ratio bandwidth (ARBW). A prototype of this antenna is fabricated and tested. The size of proposed antenna is 0.93λ₀ × 0.93λ₀ × 0.017λ₀ (λ₀ denotes the space wavelength corresponding to the center frequency 10.4 GHz). The measured 10‐dB IBW and 3‐dB ARBW are 13.6% (9.8‐11.23 GHz), 11.2% (9.9‐11.07 GHz) respectively, and peak gain in the overlapping band is 9.8 dBi.     

Compact broadband circularly polarized slot‐patch antenna array

A simple design of circularly polarized slot‐patch antenna array with broadband operation and compact size is presented in this article. The antenna element consists of a circular slot and a semicircular patch, which are etched on both sides of a substrate. For the gain and axial ratio (AR) bandwidth enhancement, its array antennas are implemented in a 2 × 2 arrangement and fed by a sequential‐phase feeding network. The final 2 × 2 antenna array prototype with compact lateral dimension of 0.8λ_L × 0.8λ_L (λ_L is the lowest frequency within AR bandwidth) yielded a measured impedance bandwidth of 103.83% (2.76‐8.72 GHz) and a measured AR bandwidth of 94.62% (2.45‐6.85 GHz). The peak gain values within the AR bandwidth are from 2.85 to 8.71 dBi. A good agreement between the simulated and measured results is achieved. This antenna array is suitable for multiservice wireless systems covering WiMAX, WLAN and C‐band applications such as satellite communications.     

A high‐isolation dual‐polarized quad‐patch antenna fed by stacked substrate integrated waveguides for millimeter‐wave application

A high‐isolation dual‐polarized quad‐patch antenna fed by stacked substrate integrated waveguide (SIW) that is suitable for millimeter‐wave band is proposed in this paper. The antenna consists of a quad‐patch radiator, a two‐layer SIW feeding structure and two feeding ports for horizontal and vertical polarization. The two‐layer stacked SIW feeding structure achieves the high isolation between the two feeding ports (|S₂₁| ≤ ?45 dB). Based on the proposed element, a 1 × 4 antenna array with a simple series‐fed network is also designed and investigated. A prototype working at the frequency band from 38 to 40 GHz is fabricated and tested. The results indicate that the proposed antenna has good radiation performance at 38 GHz that covers future 5G applications.     

Ten switched‐beams with 2 × 2 series‐fed 2.4 GHz array antenna and a simple beam‐switching network

This article presents a 2 × 2 series fed 2.4 GHz patch antenna array having multiple beam switching capabilities by using two simple 3 dB/90° couplers to achieve required amplitude and phase excitations for array elements with reduced complexity, cost and size. The beam switching performance with consistent gain and low side lobe levels (SLL) is achieved by exciting the array elements from orthogonally placed thin quarter‐wave (λ_g/4) feeds. The implemented array is capable to generate ten (10) switched‐beams in 2‐D space when series fed elements are excited from respective ports through 3 dB quadrature couplers. The dual polarized characteristics of presented array provide intrinsic interport isolation between perpendicularly placed ports through polarization diversity to achieve independent beam switching capabilities for intended directions. The implemented antenna array on 1.575 mm thick low loss (tan δ = 0.003) NH9450 substrate with ε_r = 4.5 ± 0.10 provides 10 dB return loss impedance bandwidth of more than 50 MHz. The measured beam switching loss is around 0.8 dB for beams switched at θ = ±20°, Ф = 0°, 90°, and 45° with average peak gain of 9.5 dBi and SLL ≤ ?10 dB in all cases. The novelty of this work is the capability of generating ten dual polarized switched‐beams by using only two 3 dB/90° couplers as beam controllers.     

Integrated circular polarized microstrip antenna with dual‐mode‐polarization insensitive characteristics

A dual‐mode circularly polarized compact antenna with integrated left‐hand and right‐hand circular polarization (LHCP and RHCP) is presented in this work. A multilayer arrangement of a square patch and square ring structure with an irregular transmission line is analyzed for dual‐band, dual‐CP operation. To realize dual mode propagation the proposed structure is excited using electromagnetic coupling technique. Succeeding proximity feeding with T‐stub match is analyzed, which conveys impedance bandwidth of 180 and 300 MHz within |S₁₁| < ?10 dB at 3.5 and 5.5 GHz. The designed CP elements is suitably arranged with feed line for generating two orthogonal polarization of equal amplitude and a 90° phase difference at both the resonant modes (TM₁₀ and TM₀₁). Alterable LHCP and RHCP performance is realized by altering the compensated position and peculiar angle. Having both LHCP and RHCP polarization this design shows polarization insensitive characteristic. Each LHCP and RHCP antenna element accomplished a 3‐dB AR of 70 and 120 MHz with a gain up to 6 dBi. With a low profile of 0.27λ₀ × 0.27λ₀ × 0.04λ₀, the CP antenna is fabricated, and the performance is validated through experimental analysis. With all the viable characteristics, the antenna is proposed for Wi‐MAX/WLAN communication.     

Spoof surface plasmon polariton‐fed circularly polarized leaky‐wave antenna with suppressed side‐lobe levels

A wide‐angle scanning circularly polarized (CP) leaky‐wave antenna (LWA) with suppressed side‐lobe levels (SLLs) is proposed, which can be a good candidate for future radar and wireless communication systems. The LWA consists of 12 cross slotted elliptical patch elements, which are fed by a microstrip spoof surface plasmon polariton (SSPP) line. Two fundamental modes of the patch array with two orthogonal polarizations can be excited by the electromagnetic coupling between the array and the SSPP line. By optimizing the elliptical eccentricity e and etching cross slots on the elliptical patch array, a 90° phase difference is introduced, and then, the CP radiation is realized. A tapered aperture field distribution is also realized by adjusting coupling intensities between the patch elements and the SSPP line, which is beneficial to reduce the SLLs. The electrical size of the LWA is 1.29λ₀ × 6.02λ₀ × 0.08λ₀, where λ₀ is air wavelength at 12.9 GHz (broadside direction). Both the simulated and measured results indicate that the CP operating band is 12.0 to 15.0 GHz. The proposed CP LWA scans continuously from ?14° to 38°. In the whole operating band, the axial ratios are less than 3 dB, and the SLLs are less than ?20 dB as well.     

A WiMAX circularly polarized antenna array using slot‐coupling feeding technique

In this letter, we present a circular polarization antenna array using the novel slot‐coupling feeding technique. This antenna includes eight elements which are installed in line, each array element is fed by means of two microstrip lines with equal amplitude and phase rotation of 90°. The feeding microstrip lines are coupled to a square patch through a square‐ring slot realized in the feeding network ground plane. With the presence of the slots, this antenna array is able to cover the range of frequency of 3 GHz to 4 GHz. The size of the proposed antenna array is 7λ × 1.8λ × 0.4λ. The measured gain is 15.2 dBi and the bandwidth of S11< ?10 dB is 1 GHz (3–4 GHz, 28%). The antenna array is suited for the WiMAX applications. With the use of slot‐coupling feeding technique, the measured bandwidth for axial ratio < 3 dB is about 24% in the WiMAX frequency band (3.3–3.8GHz). The measured HPBW of the y–z planes is larger than 62°. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:567–574, 2016.     

Planar circularly polarized X‐band array antenna with low sidelobe and high aperture efficiency for small satellites

A planar broadband circularly polarized (CP) X‐band array antenna with low sidelobe and high aperture efficiency is presented for small satellite applications. The array design is composed of 4 × 4 broadband CP stacked patch elements, which are fed by a feeding network consisted of unequal series‐parallel power dividers to achieve the low sidelobe and high aperture efficiency. The final prototype with overall size of 100 mm × 100 mm × 3 mm (2.73λ₀ × 2.73λ₀ × 0.082λ₀ at 8.2 GHz) was fabricated and measured. The antenna has a broadband characteristic with |S₁₁| < ?10 dB bandwidth of 15.9% (7.52‐8.82 GHz) and 3‐dB axial ratio bandwidth of 11.95% (7.63‐8.60 GHz). Also, it achieves an excellent broadside CP radiation with a gain of 17.2‐20.03 dBic, a sidelobe level of <?20 dB, and aperture efficiency of 65% to 97.5%. With these features, the proposed antenna is a good candidate for high‐speed data downlink onboard small satellites (MiniSat, MicroSat, NanoSat, and CubeSat).     

Coplanar waveguide‐fed electrically small dual‐polarized short‐ended zeroth‐order resonating antenna using Ω‐shaped capacitor and single‐split ring resonator for GPS/WiMAX/WLAN/C‐band applications

This work explains the design and analysis of a triple‐band electrically small (ka = 0.56 < 1) zeroth‐order resonating (ZOR) antenna with wideband circular polarization (CP) characteristics. The antenna compactness is obtained due to ZOR frequency of composite right/left‐handed (CRLH) transmission line (TL) and wideband CP radiation are achieved due to the introduction of single‐split ring resonator and asymmetric coplanar waveguide fed ground plane. The proposed antenna obtains an overall electrical size including the ground plane of 0.124 λ₀ × 0.131 λ₀ × 0.005 λ₀ at 1.58 GHz and physical dimension of 23.7 × 25 × 1 mm³ are achieved. The antenna provides a size reduction of 44.95% compared to a conventional monopole antenna. The novelty behind the ohm‐shaped capacitor is the generation of extra miniaturization with better antenna compactness. The antenna provides dual‐polarized radiation pattern with linear polarization radiation at 1.58 and 3.54 GHz, wideband CP radiation at 5.8 GHz. The antenna measured results shows good impedance bandwidth of 5%, 6.21%, and 57.5% for the three bands centered at 1.58, 3.54, and 5.8 GHz with a wider axial ratio bandwidth (ARBW) of 25.47% is obtained in the third band. The antenna provides a higher level of compactness, wider ARBW, good radiation efficiency, and wider S₁₁ bandwidth. Hence, the proposed antenna is suitable for use in GPS L1 band (1.565‐1.585 GHz), WiMAX 3.5 GHz (3.4‐3.8 GHz) GHz, WLAN 5.2/5.8 GHz (5.15‐5.825 GHz), and C‐band (4‐8 GHz) wireless application systems.     

Reconfigurable multibeam feed network for 38 GHz application

A feed network based on substrate integrated waveguide for 38 GHz application is proposed in this article. The network consists of a 90° hybrid, a 180° hybrid, a power divider, and a switchable phase shifter. There are two input ports in the reconfigurable multibeam feed network (RMBFN) and a set of symmetrical radiation pattern will be excited by the two input ports. In addition, the other symmetrical patterns will be obtained by adjusting the different states of the switchable phase shifter. The simulated results show that the S₁₁ and S₂₂ are found to be better than ?13 dB over 37‐40 GHz. Meanwhile, the amplitude of the three output ports is about ?6.6 ± 1 dB, and the phase difference is ±60 ± 10° or ±120 ± 10°. When the proposed RMBFN feeds for an antenna array, four different beams with the main beam pointing to the ±22 ± 3° and ±43 ± 3° are obtained.     

A novel dual‐mode patch antenna with pattern diversity and beam‐tilting for aircraft applications

A dual‐mode patch antenna with pattern diversity that is beam‐tilted in a specific direction is presented. By placing a rectangular metal cavity below the circular patch and simultaneously shorting one end of the patch, the antenna produces tilted beams for dual‐mode radiation patterns. One pattern is excited using a proximity‐fed L‐shaped probe that generates a beam with a tilt angle of 25° from the broadside direction. The second pattern is excited using a coplanar waveguide (CPW)‐based feeding network that generates two beams with a tilt angle of θ_max = ±45° in the directions of ?_max = 70° and ? 70°. The tilt angle can be varied by adjusting the metal cavity's length. A prototype antenna for operation at 2.38 GHz was fabricated and measured. The results indicate that the overlapped bandwidth (|S₁₁| < ?10 dB) for the two patterns is 330 MHz (2.22‐2.55 GHz). The measured peak gains for the two patterns are 6.74‐6.94 dBi and 5.82‐6.74 dBi, respectively. The isolation between the two ports is 18 dB.     

A miniaturized circularly polarized multi‐dipole antenna with wide axial‐ratio beamwidth via loading loop resonators

A miniaturized, loop resonators (LRs)‐loaded, circularly polarized (CP) multi‐dipole antenna with wide axial‐ratio (AR) beamwidth is proposed and demonstrated in this article. The radiator of this CP antenna consists of two pairs of parallel dipoles loaded with four LRs at their corners. By increasing the length of the LR, or decreasing the coupling space between the dipole and the LR, the effective length of the dipole can be lengthened significantly and thus the working frequency can be reduced without increasing the whole aperture size. As a result, a miniaturized radiator structure is completed. A feeding network consisting of a T‐shaped coupling feeding structure and four coplanar striplines having different lengths are specially designed to feed these dipoles with approximately the same magnitude and 90° phase quadrature. What is more, a cavity reflector is employed to achieve a unidirectional radiation with wide axial‐ratio beamwidth. The radiator of the proposed CP antenna has a small aperture size of only 0.34λ₀ × 0.34λ₀, where λ₀ is the free space wavelength at the working frequency. Measured results are in a good agreement with the corresponding simulated counterparts. Especially, the experimental results show that the antenna has achieved a wide AR beamwidth of 182° and 174° at the center frequency in the xoz and yoz planes, respectively.     

A beam scanning Fabry–Pérot cavity antenna for millimeter‐wave applications

A beam scanning Fabry‐Pérot cavity antenna (FPCA) for 28 GHz‐band is presented in this article. The proposed antenna consists of a slot‐fed patch antenna and several layers of perforated superstrates with different dielectric constant. The beam of the antenna can be controlled by moving the superstrate over the antenna. By increasing the offset between the feeding antenna and the superstrate, a larger tilt angle can be obtained. The size of the antenna is 0.95λ₀ × 0.95λ₀ × 0.48λ₀ at 28.5 GHz. The results show the proposed antenna achieves an impedance bandwidth (S₁₁ < ‐10 dB) of 10.5% (27.2‐30.2 GHz), and the beam can be scanned from 0° to 14° in the yoz‐plane with the offset changed from 0 mm to 2 mm. The gain of the antenna is enhanced by 5 dBi in comparison with the feeding antenna without the superstrate, which ranges from 10.91 to 11.53 dBi with the different offset. The proposed antenna is fabricated and shows a good agreement with simulated result.     

A compact dual‐band zeroth‐order resonator antenna loaded with meander line inductor

A novel zeroth‐order resonator (ZOR) meta‐material (MTM) antenna with dual‐band is suggested using compound right/left handed transmission line as MTM. In this article, suggested antenna consists of patch through series gap, two meander line inductors, and two circular stubs. The MTM antenna is compact in size which shows dual‐band properties with first band centered at 2.47 GHz (2.05‐2.89 GHz) and second band is centered at 5.9 GHz (3.70‐8.10 GHz) with impedance bandwidth of (S₁₁ < ? 10 dB) 34.69% and 72.45%, respectively. At ZOR mode (2.35 GHz), the suggested antenna has overall dimension of 0.197λ_o × 0.07λ_o × 0.011λ_o with gain of 1.65 dB for ZOR band and 3.35 dB for first positive order resonator band which covers the applications like Bluetooth (2.4 GHZ), TV/Radio/Data (3.700‐6.425 GHz), WLAN (5‐5.16 GHz), C band frequencies (5.15‐5.35, 5.47‐5.725, or 5.725‐5.875 GHz) and satellite communication (7.25‐7.9 GHz). The radiation patterns of suggested structure are steady during the operating band for which sample antenna has been fabricated and confirmed experimentally. It exhibits novel omnidirectional radiation characteristics in phi = 0° plane with lower cross‐polarization values.     

A dual‐band dual‐polarized cubical DRA coupled with new modified cross‐shaped slot for ISM (2.4 GHz) and Wi‐MAX (3.3‐3.6 GHz) band applications

In this article, a new modified cross‐shaped coupled cubical dielectric resonator antenna (DRA) has been investigated for dual‐band dual‐polarized applications. The linearly polarized (LP) fields in DRA has been generated by using a single slot in the ground plane and kept at either 45° (S_L1) or ?45° (S_L2) from the microstrip feed line. Combining these two slots (S_L1 and S_L2) in the modified ground plane, the proposed structure able to generate circularly polarized (CP) field in DRA. But the generated CP field is not enough to cover ISM 2400 band. To achieve CP in ISM 2400 band, an extra slot (S_L3) to the existing slots and an extra strip (S_T) in the circular ring feed line have been included. This modified final antenna arrangement has been able to produce LP (due to loading effect, ie, slot and DRA) and CP fields (orthogonal modes have been generated, ie, TE ^x₁₁₁ and TE ^y₁₁₁), simultaneously. The measured CP and LP, ?10 dB impedance bandwidths are 11.85% (2.38‐2.68 GHz) and 9.11% (3.25‐3.56 GHz) in combination with the 3‐dB axial ratio bandwidth of 4.11% (2.38‐2.48 GHz). The generated CP and LP fields are used for different wireless communication bands such as ISM 2400 and Wi‐MAX (3.3‐3.7 GHz) bands.     

Wideband circularly polarized hybrid dielectric resonator antenna with bi‐directional radiation characteristics for various wireless applications

In this article, a wideband circularly polarized (CP) dielectric resonator (DR) over an asymmetric‐slot radiator based hybrid‐DR antenna is proposed with bi‐directional radiation characteristics. Bi‐directional CP radiation of the dual sense is obtained using a rectangular‐DR over asymmetric‐rectangular‐slot radiator with L‐shaped feed line. The asymmetric‐slot radiator feed by L‐shaped stub with the coplanar waveguide is used for generating two orthogonal modes, namely TE ^x _δ11 and TE^y_1δ1 in the combined (rectangular‐DR and asymmetric‐slot radiator) hybrid‐DR antenna, which is verified by the distribution of electric field inside the rectangular DRA. The measured reflection coefficient bandwidth (S₁₁ < ?10 dB) and axial ratio (AR) bandwidth (AR < 3 dB) of the hybrid‐DR antenna are 80.5% (1.87‐4.39 GHz) and 43.8% (1.75‐2.73 GHz), respectively. The antenna radiation is in the broadside (θ = 0°, ? = 0°) direction as well as in the backside (θ = 180°, φ = 0°) direction with equal magnitudes in both the directions. Right‐handed and left‐handed CP waves are achieved respectively, in the boresight (+Z) and the backside (?Z) directions. The proposed CP hybrid‐DR antenna gives an average gain of 3.55 dBic and radiation efficiency of 95.0% in both directions. The proposed antenna covers various wireless useful bands such as ISM 2400 band, Wi‐Fi, Bluetooth, and Wi‐MAX (2.5‐2.7 GHz).     

Design of high gain/directional ultra‐wideband antenna for radar imaging systems

A compact size of 40 × 40 mm² ( λ₀ × λ₀ ) semi‐elliptical slotted ground structure (SESGS) directional ultra‐wideband (UWB) antenna is proposed for radar imaging applications. A vertical semi‐elliptical slot is inserted into ground and subsequently, an axis of semi‐ellipse is rotated diagonally (with 45°) in direction of the substrate. Axes of semi‐ellipse are optimized symmetrically around the circular patch to work antenna as a reflector. Furthermore, semi‐elliptical slot is rotated horizontally (with 90°) again to improve the impedance bandwidth. Proposed antenna achieves fractional bandwidth around 83% covering the UWB frequency range from 4.40 to 10.60 GHz (S₁₁ < ?10 dB) having 4.5/6/7/8/9.3/10.2 GHz resonant frequencies. Also, antenna is capable to send low‐distortion Gaussian pulses with fidelity factor more than 95% in time‐domain. Measured gain and half power beam width (HPBW) are 6.1‐9.1 dBi and 44°‐29° in 4.40‐10.60 GHz band, respectively, which show an improvement of 1‐3 dBi in gain and half power beam‐width is reduced by 5°‐10° when compared with previously designed antennas. Experimental results show good agreement with CST simulation.     

Compact wideband circularly polarized horn antenna with tapered slot‐coupled feeding for Ku‐band applications

A compact wideband circularly polarized (CP) horn antenna with slot‐coupled feeding structure at Ku band for satellite communication is devised. The proposed design is based on a square aperture horn antenna with two orthogonal ridges, which is fed by nonuniform curved slot along the diagonal of the horn on the bottom cavity. And in order to improve the impedance matching, a staircase typed ridge is connected the feeding probe as a matching network. Moreover, two orthogonal ridges are excited with a tapered slot coupled by the staircase ridges via feeding probe. Wideband CP performance is achieved with an overall physical dimension of 9 mm × 9 mm × 14 mm (0.045λ₀ × 0.045λ₀ × 0.07λ₀ at frequency of 15 GHz). It is experimentally demonstrated that the proposed antenna achieves: a wide 10‐dB return loss bandwidth of about 2.4 GHz, a 3‐dB axial ratio bandwidth of 1 GHz, and a peak gain of 6.5 dBi.     

Novel planar reconfigurable circularly polarized complementary antenna for unidirectional end‐fire radiation

In this article, a novel planar reconfigurable circular polarization (CP) complementary antenna for unidirectional end‐fire radiation is proposed. Its radiator is the combination of a shorted quarter wavelength patch and an electric dipole, which provide the vertical and horizontal polarizations, respectively. By adding a 90° phase delay line, the proposed antenna radiates CP electromagnetic waves in the unidirectional end‐fire direction. Four p‐i‐n diodes are also inserted at joints of the electric dipole and the phase delay lines, and two orthogonal CP states, left‐hand (LH) and right‐hand (RH) CPs, can be switched. In order to reduce the number of DC bias lines, electric dipole arms on both sides of the substrate are connected by metal via‐holes, which simplifies the DC bias lines. The proposed antenna at 2.45 GHz is designed and fabricated. Its measured impedance bandwidth with |S₁₁| < ?10 dB and 3‐dB axial ratio bandwidth are 2.1% and 10.7%, respectively. Additionally, its maximum half power beamwidth in xoz plane is 196°. Reasonable agreement between the measured and simulated results validates the polarization reconfigurability of the proposed antenna.