Dielectric properties of (1 − x)(Mg0.95Zn0.05)TiO3-x(Na0.5Nd0.5)TiO3 ceramic system at microwave frequencies

Ceramics in the system (1 − x)(Mg_0.95Zn_0.05)TiO₃-x(Na_0.5Nd_0.5)TiO₃ were prepared by the conventional mixed oxide route. It shows a two-phase system of an ilmenite structured (Mg_0.95Zn_0.05)TiO₃ and a perovskite structured (Na_0.5Nd_0.5)TiO₃, which were confirmed by XRD and EDX. In addition, (Mg_0.95Zn_0.05)Ti₂O₅ was identified as a second phase. It was also responsible for a rapid drop in the Q × f value. The temperature coefficient of resonant frequency was a function of compositional ratio. Specimen with x = 0.16 possessed an excellent combination of microwave dielectric properties: ε_r ~ 24.27, Q × f ~ 82,000 GHz (at 9 GHz) and τ_f ~ 0 ppm/°C.     

Microstructure and electrical properties of Ba0.7Sr0.3(Ti1 − xZrx)O3 thin films prepared on copper foils with sol-gel method

Ba_0.7Sr_0.3(Ti_1 − xZr_x)O₃ (x = 0, 0.1, 0.2) (BSZT) thin films have been prepared on copper foils using sol-gel method. The films were annealed in an atmosphere with low oxygen pressure so that the substrate oxidation was avoided and the formation of the perovskite phase was allowed. The X-ray diffraction results show a stable polycrystalline perovskite phase, with the diffraction peaks of the BSZT films shifting toward the smaller 2θ with increasing Zr content. Scanning electron microscopy images show that the grain size of the BSZT thin films decreases with increasing Zr content. High resolution transmission electron microscopy shows the clear lattice and domain structure in the film. The dielectric peaks of the BSZT thin films broaden with increasing Zr content. Leakage current density of Ba_0.7Sr_0.3(Ti_1 − xZr_x)O₃ (x = 0.1) thin film is the lowest over the whole applied voltage.     

Enhanced tunable dielectric properties of Ba0.5Sr0.5TiO3/Bi1.5Zn1.0Nb1.5O7 multilayer thin films by a sol-gel process

Ba_0.5Sr_0.5TiO₃(BST)/Bi_1.5Zn_1.0Nb_1.5O₇(BZN) multilayer thin films were prepared on Pt/Ti/SiO₂/Si substrates by a sol-gel method. The structures and morphologies of BST/BZN multilayer thin films were analyzed by X-ray diffraction (XRD) and field-emission scanning electron microscope. The XRD results showed that the perovskite BST and the cubic pyrochlore BZN phases can be observed in the multilayer thin films annealed at 700 °C and 750 °C. The surface of the multilayer thin films annealed at 750 °C was smooth and crack-free. The BST/BZN multilayer thin films annealed at 750 °C exhibited a medium dielectric constant of around 147, a low loss tangent of 0.0034, and a relative tunability of 12% measured with dc bias field of 580 kV/cm at 10 kHz.     

Morphotropic phase boundary in high temperature ferroelectric xBi(Zn1/2Ti1/2)O3 − yPbZrO3 − zPbTiO3 perovskite ternary solid solution

A bismuth and lead oxide based perovskite ternary solid solution xBi(Zn_1/2Ti_1/2)O₃ − yPbZrO₃ − zPbTiO₃ (xBZT − yPZ − zPT) was investigated as an attempt to develop a high T_C ferroelectric material for piezoelectric sensor and actuator applications. A morphotropic phase boundary (MPB) between rhombohedral and tetragonal phases was determined through an XRD study on a pseudobinary line 0.1BZT − 0.9[xPT − (1 − x)PZ] for composition 0.1Bi(Zn_1/2Ti_1/2)O₃ − 0.5PbZrO₃ − 0.4PbTiO₃. Enhanced piezoelectric and ferroelectric activities were observed for MPB composition with dielectric constant ε_r′ ~ 23,000 at Curie temperature (T_C) ≈ 320 °C, remanent polarization (P_r) = 35 μC/cm², piezoelectric coefficient (d₃₃) = 300 pC/N, unipolar strain = 0.15%, and electromechanical coupling coefficient (k_P) = 0.45.     

Synthesis and electromagnetic properties of microwave absorbing material: Cox(Cu0.5Zn0.5)1−xFe2O4 (0 < x < 1) nanoparticles

Spinel ferrite Co_x(Cu_0.5Zn_0.5)_1−xFe₂O₄ over a compositional range 0 < x < 1 was prepared using a simple hydrothermal method. Particle sizes could be varied from 14 to 25 nm by changing the x value. X-ray diffraction results confirmed that all the as-prepared nanoparticles revealed typical spinel structure and transmission electron microscopy images showed that the particle size of the samples increased with increasing x value. The magnetic properties of the as-prepared Co_x(Cu_0.5Zn_0.5)_1−xFe₂O₄ nanoparticles have been systematically examined. The maximum saturation magnetization existed at the highest Co content (x = 1). The electromagnetic properties of all the samples have been measured by an Agilent network analyzer and the results showed that Co_0.1(Cu_0.5Zn_0.5)_0.9Fe₂O₄ possessed the best microwave absorbing properties.     

Effect of CuO addition to Nd(Zn1/2Ti1/2)O3 ceramics on sintering behavior and microwave dielectric properties

The microwave dielectric properties and microstructures of CuO-doped Nd(Zn_1/2Ti_1/2)O₃ ceramics prepared by the conventional solid-state route were investigated. The prepared Nd(Zn_1/2Ti_1/2)O₃ exhibits a mixture of Zn and Ti showing 1:1 order in the B-site. As an appropriate sintering aid, not only did CuO lower the sintering temperature, it could effectively hold back the evaporation of Zn in the Nd(Zn_1/2Ti_1/2)O₃. Moreover, CuO only resided in boundaries, which was confirmed by EDX analysis. The measured lattice parameters of CuO-doped Nd(Zn_1/2Ti_1/2)O₃ (a = 5.4652 ± 0.0005 ?, b = 5.6399 ± 0.0007 ?, c = 7.7797 ± 0.0008 ? and β = 90.01 ± 0.01°) retained identical to that of the pure Nd(Zn_1/2Ti_1/2)O₃ in all cases. In comparison with the pure Nd(Zn_1/2Ti_1/2)O₃ ceramics, specimen with 1 wt.% CuO addition possesses a compatible combination of dielectric properties with a ε_r of 30.68, a Q × f of 158,000 GHz (at 8 GHz) and a τ_f of − 45 ppm/°C at 1270 °C. It also indicated a 60 °C lowering in the sintering temperature. The proposed dielectrics can be a very promising candidate material for microwave or millimeter wave applications requiring extremely low dielectric loss.     

Tantalum influence on physical properties of (K0.5Na0.5)(Nb1−xTax)O3 ceramics

Lead-free (K_0.5Na_0.5)(Nb_1−xTa_x)O₃ ceramics with x = 0.00-0.30 were prepared by the solid-state reaction technique. The effects of Ta on microstructure, crystallographic structure, phase transition and piezoelectric properties have been investigated. It has been shown that the substitution of Ta decreases Curie temperature T_C and orthorhombic-tetragonal phase transition temperature T_O-T, while increasing the rhombohedral-orthorhombic phase transition temperature T_R-O. In addition, piezoelectric activity is enhanced with the increase of Ta content. The ceramics with x = 0.30 have the high value of piezoelectric coefficient d₃₃ = 205 pC/N. Moreover, k_p shows little temperature dependence between −75° C and 75 °C, and d₃₃ exhibits very good thermal stability over the range from −196 °C to 75 °C in the aging test.     

Dielectric and piezoelectric properties of Y2O3 doped (Bi0.5Na0.5)0.94Ba0.06TiO3 lead-free piezoelectric ceramics

Y₂O₃ doped lead-free piezoelectric ceramics (Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ (0-0.7 wt%) were synthesized by the conventional solid state reaction method, and the effect of Y₂O₃ addition on the structure and electrical properties was investigated. X-ray diffraction shows that Y₂O₃ diffuses into the lattice of (Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ to form a solid solution with a pure perovskite structure. The temperature dependence of dielectric constant of Y₂O₃ doped samples under various frequencies indicates obvious relaxor characteristics different from typical relaxor ferroelectric and the mechanism of the relaxor behavior was discussed. The optimum piezoelectric properties of piezoelectric constant d₃₃ = 137 pC/N and the electromechanical coupling factor k_p = 0.30 are obtained at 0.5% and 0.1% Y₂O₃ addition, respectively.     

Structural characterization of 0.5PbMg1/3Nb2/3O3-0.5BaxPb(1−x)TiO3 powders

The present work reports the effects caused by barium on phase formation, morphology and sintering of lead magnesium niobate-lead titanate (PMN-50PT). Ab initio study of 0.5Pb(Mg_1/3Nb_2/3)O₃-0.5(Ba_xPb_(1−x)TiO₃) ceramic powders, with x = 0, 0.20, and 0.40 was proposed, considering that the partial substitution of lead by barium can reestablish the equilibrium of monoclinic-tetragonal phases in the system. It was verified that even for 40 mol% of barium, it was possible to obtain pyrochlore-free PMN-PT powders. The increase of the lattice parameters of PMN-PT doped-powders confirmed dopant incorporation into the perovskite phase. The presence of barium improved the reactivity of the powders, with an average particle size of 120 nm for 40 mol% of barium against 167 nm for the pure sample. Although high barium content (40 mol%) was deleterious for a dense ceramic, contents up to 20 mol% allowed 95% density when sintered at 1100 °C for 4 h.     

Effect of sintering time on crystal structure and microwave dielectric properties in aeschynite-structured (Sm1−xYx)(Ti1.5W0.5)O6 (x = 0 and 0.5) ceramics

The crystal structure and microwave dielectric properties of the (Sm_1−xY_x)(Ti_1.5W_0.5)O₆ (x = 0 and 0.5) ceramics sintered at 1375 °C for 2-50 h were investigated in this study. No secondary phase was observed in the samples sintered for various sintering times, whereas a secondary phase was formed in the (Sm_0.5Y_0.5)(Ti_1.5W_0.5)O₆ ceramic sintered at 1400 °C for 50 h. As for the microstructure analysis, the formation of the liquid phase was observed in the both of the samples sintered for 20 and 50 h. The formation of the liquid phase is related to the compositional change of Ti and W from the stoichiometric composition of the samples caused by the instability of crystal structure. The dielectric constants were increased with increased sintering time in the both of the samples, though variations in the temperature coefficient of resonant frequency of the samples were not recognized with the variation in the sintering time. Moreover, although the quality factors of the each sample increased with increasing the sintering time from 2 to 10 h, decreases in the quality factors were recognized when the sintering time was over 10 h.     

Structure and thermal conductivity of Gd2(TixZr1 − x)2O7 ceramics

The Gd₂(Ti_xZr_1 − x)₂O₇ (x = 0, 0.25, 0.50, 0.75, 1.00) ceramics were synthesized by solid state reaction at 1650 °C for 10 h in air. The relative density and structure of Gd₂(Ti_xZr_1 − x)₂O₇ were analyzed by the Archimedes method and X-ray diffraction. The thermal diffusivity of Gd₂(Ti_xZr_1 − x)₂O₇ from room temperature to 1400 °C was measured by a laser-flash method. The Gd₂Zr₂O₇ has a defect fluorite-type structure; however, Gd₂(Ti_xZr_1 − x)₂O₇ (0.25 ≤ x ≤ 1.00) compositions exhibit an ordered pyrochlore-type structure. Gd₂Zr₂O₇ and Gd₂Ti₂O₇ are infinitely soluable. The thermal conductivity of Gd₂(Ti_xZr_1 − x)₂O₇ increases with increasing Ti content under identical temperature conditions. The thermal conductivity of Gd₂(Ti_xZr_1 − x)₂O₇ first decreases gradually with the increase of temperature below 1000 °C and then increases slightly above 1000 °C. The thermal conductivity of Gd₂(Ti_xZr_1 − x)₂O₇ is within the range of 1.33 to 2.86 W m^− 1 K^− 1 from room temperature to 1400 °C.     

Ferroelectric and pyroelectric properties of (Na0.5Bi0.5)TiO3-BaTiO3 based trilayered thin films

Trilayered Bi_3.25La_0.75Ti₃O₁₂ (25 nm)/(Na_0.5Bi_0.5)_0.94Ba_0.06TiO₃ (300 nm)/Bi_3.25La_0.75Ti₃O₁₂ (25 nm) and Pb(Zr_0.4Ti_0.6)O₃ (25 nm)/(Na_0.5Bi_0.5)_0.94Ba_0.06TiO₃ (300 nm)/Pb(Zr_0.4Ti_0.6)O₃ (25 nm) thin films without undesirable phases have been deposited on Pt/Ti/SiO₂/Si substrates. It was found that the Bi_3.25La_0.75Ti₃O₁₂ and Pb(Zr_0.4Ti_0.6)O₃ layers are very effective to inhibit the charge transport in the trilayered films. Much better insulating properties than those of (Na_0.5Bi_0.5)_0.94Ba_0.06TiO₃ films have been achieved in the trilayered films. The trilayered films show good dielectric, ferroelectric and pyroelectric properties. Remnant polarizations 2P_r of 16 µC/cm² and 34 µC/cm², pyroelectric coefficients of 4.8 × 10^− 4 C m^− 2 K^− 1 and 7.0 × 10^− 4 C m^− 2 K^− 1 have been obtained for the Bi_3.25La_0.75Ti₃O₁₂/(Na_0.5Bi_0.5)_0.94Ba_0.06TiO₃/Bi_3.25La_0.75Ti₃O₁₂ and Pb(Zr_0.4Ti_0.6)O₃/(Na_0.5Bi_0.5)_0.94Ba_0.06TiO₃/Pb(Zr_0.4Ti_0.6)O₃ thin films, respectively. The trilayered films are promising candidates for sensor and actuator applications.     

Hydrothermal synthesis, structural and physico-chemical characterizations of two Nasicon phosphates: M0.50Ti2(PO4)3 (M = Mn, Co)

The family of titanium Nasicon-phosphates of generic formula M_0.5^IITi₂(PO₄)₃ has been revisited using hydrothermal techniques. Two phases have been synthesized: Mn_0.5^IITi₂(PO₄)₃ (MnTiP) and Co_0.5^IITi₂(PO₄)₃ (CoTiP). Single crystal diffraction studies show that they exhibit two different structural types. Mn_0.5^IITi₂(PO₄)₃ phosphate crystallizes in the R-3 space group, with the cell parameters a = 8.51300(10) Å and c = 21.0083(3) Å (V = 1318.52(3) Å³ and Z = 6). The Co_0.5^IITi₂(PO₄)₃ phosphate crystallizes in the R-3c space group, with a = 8.4608(9) Å and c = 21.174(2) Å (V = 1312.7(2) Å³ and Z = 6). These two compounds are clearly related to the parent Nasicon-type rhombohedral structure, which can be described using [Ti₂(PO₄)₃] framework composed of two [TiO₆] octahedral interlinked via three [PO₄] tetrahedra. ³¹P magic-angle spinning nuclear magnetic resonance (MAS-NMR) data are presented as supporting data. Curie-Weiss-type behavior is observed in the magnetic susceptibility. The phases are also characterized by IR spectroscopy and UV-visible.     

Crystal and magnetic study of the disordered perovskites Ca(Mn0.5Sb0.5)O3 and Ca(Fe0.5Sb0.5)O3

We have investigated the double perovskites Ca₂MSbO₆ (M = Mn, Fe) that have been prepared by solid-state reaction (M = Fe) and wet chemistry procedures (M = Mn). The crystal and magnetic structures have been studied from X-ray (XRD) and neutron powder diffraction (NPD) data. Rietveld refinements show that the crystal structures are orthorhombic (space group Pbnm) with complete disorder of M and Sb cations, so the formula should be rewritten as Ca(M_0.5Sb_0.5)O₃. Due to this disorder no evidences of Jahn-Teller distortion can be observed in the MnO₆ octahedra of Ca(Mn_0.5Sb_0.5)O₃, in contrast with the ordered double perovskite Sr₂MnSbO₆. Ca(Fe_0.5Sb_0.5)O₃ behaves as an antiferromagnet with an ordered magnetic moment for Fe³⁺ of 1.53(4)μ_B and a propagation vector k = 0, as investigated by low-temperature NPD. The antiferromagnetic ordering is a result of the high degree of Fe/Sb anti-site disorder of the sample, which originates the spontaneous formation of Fe-rich islands, characterized by the presence of strong Fe-O-Fe antiferromagnetic couplings with enough long-range coherence to produce a magnetic contribution perceptible by NPD. By contrast, the magnetic structure of Ca(Mn_0.5Sb_0.5)O₃ cannot be observed by low-temperature NPD because the magnitude of the ordered magnetic moments is below the detection threshold for neutrons.     

Synthesis and properties of solid solutions of hexagonal YCu0.5Ti0.5O3 with YMO3 (M = Mn, Cr, Fe, Al, Ga, and In)

Solid solutions of the type Y(Cu_0.5Ti_0.5)_1−xM_xO₃ with a hexagonal structure were prepared for M = Mn, Fe, Cr, Al, Ga, and In. A complete solid solution could be obtained only in the case of M = Mn. The green color of YCu_0.5Ti_0.5O₃ was found to be enhanced by small substitutions of Al, Ga, and In. All compositions containing Mn were black in color. Suppression of magnetic transitions is observed upon co-doping of Cu/Ti into YMnO₃. Measurements of dielectric constant suggest some magneto-electric coupling may be present in the Y(Cu_0.5Ti_0.5)_1−xMn_xO₃ solid solution.     

Study on properties of BaxSmyTi7O20 ceramics with CaO-SiO2-B2O3 glass

The effect of CaO-SiO₂-B₂O₃ (CSB) glass addition on the sintering temperature and dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics has been investigated using X-ray diffraction, scanning electron microscopy and differential thermal analysis. The CSB glass starts to melt at about 970 °C, and a small amount of CSB glass addition to Ba_xSm_yTi₇O₂₀ ceramics can greatly decrease the sintering temperature from about 1350 to about 1260 °C, which is attributed to the formation of liquid phase. It is found that the dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics are dependent on the amount of CSB glass and the microstructures of sintered samples. The product with 5 wt% CSB glass sintered at 1260 °C is optimal in these samples based on the microstructure and the properties of sintering product, when the major phases of this material are BaSm₂Ti₄O₁₂ and BaTi₄O₉. The material possesses excellent dielectric properties: ?_r = 61, tan δ = 1.5 × 10⁻⁴ at 10 GHz, temperature coefficient of dielectric constant is −75 × 10⁻⁶ °C⁻¹.     

Structural and electrical properties of Na2Pb2Eu2W2Ti4X4O30 (X = Nb, Ta) ferroelectric ceramics

A new group of tungsten bronze family Na₂Pb₂Eu₂W₂Ti₄X₄O₃₀ (X = Nb, Ta) having all the valence elements (I-VI) were prepared by a high-temperature solid-state reaction technique. The formations of the compounds were confirmed by X-ray diffraction technique with an orthorhombic structure. Surface morphology of the compounds was studied by scanning electron microscope (SEM). Studies of dielectric properties (?_r and tan δ) of the above compounds at different frequencies in a wide temperature range (300-700 K) with an impedance analyzer exhibit a ferroelectric phase transition at 580 and 394 K for Na₂Pb₂Eu₂W₂Ti₄Nb₄O₃₀ and Na₂Pb₂Eu₂W₂Ti₄Ta₄O₃₀, respectively. Ferroelectric properties of these compounds were confirmed with polarization (hysteresis) study.     

Effects of Mn doping on structural and dielectric properties of sol-gel-derived (Ba0.835Ca0.165)(Zr0.09Ti0.91)O3 thin films

We reported the effects of Mn doping on the structure and dielectric properties of (Ba_0.835Ca_0.165)(Zr_0.09Ti_0.91)O₃ (BCZT) thin films prepared by sol-gel method. The (Ba_0.835Ca_0.165)Mn_x(Zr_0.09Ti_0.91)_1 − xO₃ (x = 0, 0.002, 0.005, and 0.01) thin films exhibited a pure pseudo-cubic perovskite structure with random orientation. Scanning electron microscopy and atomic force microscopy observation showed that increasing Mn-doping amount caused a decrease in particle size and a cluster of the particles, while the film surface remained smooth and crack-free. Compared with the undoped film, Mn doped BCZT thin films exhibited smaller dielectric constant and lower dielectric loss. The figure of merit reached the maximum value of 16.7 with a tunability of 53.6% for the film with 0.5 mol % Mn doping, when a bias electric field of 400 kV/cm was applied at 100 kHz. The results indicated that the Mn doped BCZT thin films are suitable for tunable microwave device applications.     

Giant strain in Nb-doped Bi0.5(Na0.82K0.18)0.5TiO3 lead-free electromechanical ceramics

The effect of Nb substitution on the crystal structure, ferroelectric, and electric field induced strain properties of Bi_0.5(Na₈₂K_0.18)_0.5TiO₃ (BNKT) ceramics has been investigated. The coexistence of rhombohedral and tetragonal phases was found in undoped BNKT ceramics, however, Nb doping induced a phase transition to a pseudocubic phase with high electrostriction coefficients. When 3 mol% Nb was substituted on Ti ions, the electric field induced strain was markedly enhanced up to S_max/E_max = 641 pm/V, which is higher than those previously reported on non-textured lead-free electromechanical ceramics.     

Microwave dielectric properties of Ba2 − xSrxLa3Ti3NbO15 ceramics

High dielectric constant and low loss ceramics in the system Ba_2 − xSr_xLa₃Ti₃NbO₁₅ (x = 0-1) have been prepared by conventional solid-state ceramic route. Ba_2 − xSr_xLa₃Ti₃NbO₁₅ solid solutions adopted A₅B₄O₁₅ cation-deficient hexagonal perovskite structure for all compositions. The materials were characterized at microwave frequencies. They show a linear variation of dielectric properties with the value of x. Their dielectric constant varies from 48.34 to 43.03, quality factor Q_u × f from 20,291 to 39,088 GHz and temperature variation of resonant frequency from 8 to 1.39 ppm/°C as the value of x increases. These low loss ceramics might be used for dielectric resonator (DR) applications.