含冲击损伤缝合层板剩余压缩强度

通过对含冲击损伤缝合复合材料层板进行压缩实验,揭示了含损伤缝合层板在压缩载荷下的破坏模式和破坏机制.将冲击损伤等效为圆孔,利用杂交单元计算冲击后缝合层板的应力分布,采用基于特征曲线概念的点应力判据预测了含损伤缝合层板的剩余压缩强度.研究结果表明:冲击损伤近似为圆形;缝合和未缝合层板冲击后压缩的损伤模式不同;采用开口等效法可以有效分析缝合层板的剩余压缩强度;特征距离、损伤面积是影响计算结果的主要因素.     

缝合复合材料层板低速冲击及冲击后压缩实验研究

通过对缝合复合材料层板进行低速冲击和冲击后压缩实验, 研究了不同类型的缝合复合材料层板的冲击损伤特性及冲击后压缩的剩余强度。实验研究表明: 基体损伤和分层是缝合层板与未缝合层板低速冲击的主要损伤模式, 缝合层板具有更好的抗冲击性能, 更高的冲击后压缩强度。缝合密度越大的层板其抗冲击性能越好, 冲击后压缩强度越高。缝合方向为0°的缝合层板较缝合方向为90°的缝合层板具有更好的抗冲击性能和更高的冲击后压缩强度。增加0°方向铺层, 减少45°、-45°方向铺层, 可以提高缝合层板的抗冲击性能和冲击后压缩强度。     

含分层损伤缝合复合材料层板的剩余压缩强度

基于渐进损伤方法,研究了含单脱层缝合复合材料层板在压缩载荷下的剩余强度。通过商用软件ABAQUS建立了含单脱层缝合复合材料层板剩余压缩强度计算模型,考虑了子层屈曲和分层扩展对剩余强度的影响。通过UMAT子程序实现了层板失效、层间失效和缝线失效的模拟。通过嵌入式杆单元结构模拟了缝线桥联作用及失效。采用Hashin准则及刚度折减法对纤维拉压、基体拉压失效进行了模拟。通过渐进损伤分析,揭示了缝合情况下含单脱层复合材料层板的失效机理,讨论了缝合参数对剩余压缩强度的影响。所预测的破坏模式和剩余强度结果与实验能较好地吻合。分析表明缝合可以明显提高含分层损伤复合材料层板的子层屈曲载荷,抑制分层扩展,并提高层板的剩余压缩强度。     

复合材料层板低速冲击后剩余压缩强度

对两种材料体系和铺层的复合材料层合板进行低速冲击后压缩强度试验 , 以研究低速冲击后层合板的压缩破坏机理。讨论了表面凹坑深度、 背面基体裂纹长度、 损伤面积以及剩余压缩强度与冲击能量的关系。在试验研究的基础上 , 建立了复合材料低速冲击后剩余强度估算的一种椭圆形弹性核模型。该模型将冲击损伤等效为一刚度折减的椭圆形弹性核 , 采用含任意椭圆核各向异性板杂交应力有限元分析含损伤层合板的应力应变状态 ,并应用点应力判据预测层板的压缩(或压、 剪)剩余强度。理论分析与试验结果对比表明 , 该模型简单有效。      

含低速冲击损伤复合材料层合板剩余压缩强度及疲劳性能试验研究

对T300/QY8911复合材料层板进行了低速冲击、 冲击后压缩以及冲击后疲劳试验研究。通过对冲击后的层板进行目视检测和超声C扫描获得了层板受低速冲击后的若干损伤特征; 在压-压疲劳试验中, 测量了损伤的扩展情况。讨论了冲击能量与损伤面积以及冲击后剩余压缩强度的关系, 分析了含冲击损伤层合板在压缩载荷及压-压疲劳载荷下的主要破坏机制。结果表明, 低速冲击损伤对该类层板的强度和疲劳性能影响很大, 在3.75 J/mm的冲击能量下, 层板剩余压缩强度下降了65%; 在压-压疲劳载荷作用下, 其损伤扩展大致可分为两个阶段, 占整个疲劳寿命约60%的前一阶段损伤扩展较为缓慢; 而疲劳寿命的后半阶段损伤则开始加速扩展, 并导致材料破坏。     

复合材料层合板低速冲击后压-压疲劳试验研究及寿命预报

进行了复合材料层合板低速冲击和冲击后压-压疲劳试验。在疲劳试验过程中详细测量了损伤扩展情况,获得了损伤扩展规律。将冲击损伤等效为一圆形开孔,应用含椭圆形夹杂的杂交应力单元分析含圆孔有限大板的应力分布,采用特征曲线和点应力判据相结合的方式并通过引入损伤扩展规律建立了含低速冲击损伤复合材料层板压-压疲劳寿命预测模型。通过与试验数据的对比,证明了该模型的有效性。同时,该模型还可预报在疲劳载荷下含冲击损伤层板的剩余压缩强度。     

缝合复合材料可用性--环境条件下层合板的冲击后压缩性能

为了解决缝合复合材料在航空航天结构中的应用问题,对国内生产的缝合/树脂膜渗透成型工艺复合材料层合板在三种不同环境条件下的低速冲击后压缩性能进行试验研究.结果表明,缝合改变了含冲击损伤层合板的压缩破坏机理,可以大幅度提高层合板在干态常温下的冲击后剩余压缩强度,但是对湿态高温下层合板的冲击后剩余压缩强度影响不大;缝合方向对冲击损伤面积和剩余压缩强度的影响较小,其中以0°缝合较为有利.     

聚氨酯涂层对复合材料层板冲击后压缩性能的影响

对聚氨酯喷涂复合材料层板进行反复低速冲击试验和冲击后压缩试验,研究了损伤程度、层板厚度和涂层厚度对聚氨酯喷涂复合材料层合板冲击后压缩强度的影响,并通过数字图像相关(DIC)检测压缩过程分析了不同损伤程度试样的破坏过程和破坏模式。结果表明:随着冲击次数的增加冲击后压缩强度存在拐点,随着层合板厚度的增加试样的冲击后压缩强度降低,随着涂层厚度的增加含聚氨酯的试样冲击后压缩强度明显提高;压缩破坏位置与损伤程度有关,试样的损伤程度不同其压缩破坏过程也不同。     

低速冲击下复合材料层板压缩许用值

为评估航空结构中常用的T300级和T800级2种碳纤维/环氧树脂复合材料层压板的冲击后压缩许用值,对2种材料体系下具有不同厚度及铺层的层板进行了低速冲击和冲击后压缩试验;讨论了冲击能量、凹坑深度、损伤面积及冲击后剩余压缩强度等之间的关系,以及厚度、铺层、表面防护等因素对其造成的影响;重点关注了2种材料体系下各组层板的目视勉强可见冲击损伤(BVID)形成条件以及含BVID层板的剩余强度.结果表明:厚度及铺层对层板的凹坑深度-冲击能量关系影响较大,而对冲击后压缩强度-凹坑深度及冲击后压缩破坏应变-凹坑深度关系影响较小,且在相同铺层比例下,BVID对应的冲击能量随厚度近似呈线性增长.X850层板的损伤阻抗性能明显优于CCF300/5228层板的,但二者损伤容限性能相当.加铜网、涂漆等表面处理显著提高了层板的损伤阻抗,但对损伤容限性能影响不大;在损伤不超过BVID时,所有CCF300/5228试件的压缩破坏应变均大于4 000 με,而X850材料体系下压缩破坏应变均在3 000 με之上.     

复合材料层板低速冲击后疲劳性能实验研究

通过对T300/5405复合材料层板进行低速冲击后的压-压疲劳实验,研究含不同冲击损伤层板的压缩性能与其在多级应力水平下的疲劳寿命与损伤扩展,并讨论冲击能量、应力水平、损伤扩展对层板疲劳寿命的影响。结果表明:冲击损伤明显降低层板的剩余强度;在低应水平下,冲击能量越大,含冲击损伤层板的疲劳寿命越小;疲劳实验中损伤经历平稳扩展和快速扩展两个阶段,其中平稳扩展阶段约占总体寿命的80%,快速扩展阶段约占总体寿命的20%,损伤扩展速率随着应力水平降低而减小。     

Evaluation of impact damage mechanism of multi-axial stitched CFRP laminate

This study focuses on multi-axial stitched fabric, which is a thick, high performance reinforcement for large-scale composite structures. The effects of impact damage on multi-axial stitched CFRP laminates molded by vacuum-assisted resin transfer molding (VARTM) method were evaluated. Impact damage within material was evaluated by ultrasonic scanning device and optical cross-sectional observations. Probed images obtained by both non-destructive and destructive methods were compared, and internal damage distributions of multi-axial stitched CFRP laminates were clarified. In addition, residual compressive strength and fatigue property of impact-damaged CFRP laminates were evaluated by in situ damage growth monitoring using the thermo-elastic stress analyzer (TESA). Three-dimensional damage distribution of impacted CFRP laminate was obtained from ultrasonic C-scan images and cross-sectional photographs. Damage progress behavior was observed on a destructive and non-destructive basis by post-impact fatigue (PIF) test.     

缝合复合材料层板三维纤维弯曲模型及压缩强度预报

提出了三维纤维弯曲模型, 基于有限元法和周期性边界条件建立了缝合层板压缩强度分析方法, 采用桥联模型和最大应力判据分析损伤扩展并获得压缩强度, 预报结果与试验吻合较好。详细探讨了缝合参数对层合板压缩强度的影响规律, 结果表明: 缝合方向与表面纤维方向一致时, 较小的缝合针距和行距、较大的缝合线半径对压缩强度较为有利; 缝合方向与表面纤维方向垂直时, 较小的缝合针距和缝合线半径、较大的缝合行距对压缩强度较为有利。      

Compressive behaviour of thin-skin stiffened composite panels with a stress raiser

The in-plane compressive behaviour of thin-skin stiffened composite panels with a stress concentrator in the form of an open hole or low velocity impact damage is examined analytically. Drop weight impact in laminated polymer composites causes matrix cracking, delaminations and fibre breakage, which together can seriously degrade the laminate compressive strength. Experimental studies, using ultrasonic C-scan images and X-ray shadow radiography, indicated that the overall damage resembles a hole. Under uniaxial compression loading, 0° fibre microbuckling surrounded by delamination grows laterally (like a crack) from the impact site as the applied load is increased. These local buckled regions continued to propagate, first in discrete increments and then rapidly at failure load. The damage pattern is very similar to that observed in laminated plates with open holes loaded in compression. Because of this resemblance, a fracture mechanics model, developed initially to predict notched compressive strength, was applied to estimate the compression-after-impact (CAI) strength of a stiffened panel; in the analysis the impact damage is replaced with an equivalent open hole. Also, the maximum stress failure criterion is employed to estimate the residual compressive strength of the panel. The unnotched compressive strength of the composite laminate required in the analysis is obtained from a three-dimensional stability theory of deformable bodies. The influence of the stiffener on the compressive strength of the thin-skin panel is examined and included in the analysis. A good agreement between experimental measurements and predicted values for the critical failure load is obtained.     

Z 向增强泡沫夹芯复合材料冲击损伤及冲击后压缩性能

基于热压罐成型工艺, 选择了树脂柱Z向增强泡沫芯材、碳纤维Z向增强泡沫芯材、Kevlar纤维缝纫增强泡沫芯材3种Z向增强复合材料结构, 对夹芯结构进行了低速冲击损伤和冲击后压缩(CAI)性能研究, 考察了不同Z向增强方式对冲击损伤面积和破坏模式的影响。结果表明, Z向增强对泡沫芯材产生了初始损伤, 其冲击后损伤面积大于未增强泡沫夹芯结构; 但Z向增强改变了夹芯结构的压缩破坏机制。通过选用合适的Z向增强材料和Z向增强参数, 能够提高夹芯结构的压缩强度和CAI强度。其中当增强材料为碳纤维, 增强参数为10 mm×10 mm时, 压缩强度提高了13%, CAI强度提高超过40%。     

Effect of stitch density and stitch thread thickness on compression after impact strength and response of stitched composites

In this paper, the damage failure and behaviour of stitched composites under compression after impact (CAI) loading are experimentally investigated. This study focuses on the effect of stitch density and stitch thread thickness on the CAI strength and response of laminated composites reinforced by through-thickness stitching. Experimental findings show that stitched composites have higher CAI failure load and displacement, which corresponds to higher energy absorption during CAI damage, mainly attributed to greater energy consumption by stitch fibre rupture. The coupling relationships between CAI strength, impact energy, stitch density and stitch thread thickness are also revealed. It is understood that the effectiveness of stitching has high dependency on the applied impact energy. At low impact energy range, CAI strength is found to be solely dependent on stitch density, showing no influence of stitch thread thickness. It is however observed that stitch fibre bridging is rendered ineffective in moderately stitched laminates during compressive failure, as local buckling occurs between stitch threads, resulting in unstitched and moderately stitched laminates have similar CAI strength. The CAI strength of densely stitched laminates is much higher due to effective stitch fibre bridging and numerous stitch thread breakages. At high impact energy level, CAI strength is discovered to be intimately related to both stitch density and stitch thread thickness. Since CAI failure initiates from impact-induced delamination area, stitch fibre bridging is considerable for all specimens due to the relatively large delamination area present. Stitch threads effectively bridge the delaminated area, inhibit local buckling and suppress delamination propagation, thus leading to increased CAI strength for laminates stitched with higher stitch density and larger stitch thread thickness. Fracture mechanisms and crack bridging phenomenon, elucidated by X-ray radiography are also presented and discussed. This study reveals novel understanding on the effectiveness of stitch parameters for improving impact tolerance of stitched composites.     

低速冲击后复合材料层合板的压缩破坏行为

对缝纫层合板和无缝纫层合板进行低速冲击后压缩破坏实验,以研究低速冲击后层合板的压缩破坏机理。采用C扫描、X射线、热揭层等技术对层合板内的损伤进行测量和对比。结果表明,界面不是很强的碳纤维增强复合材料层合板低速冲击后受压时,层合板非冲击面的子层屈曲及其扩展是导致层合板冲击后压缩强度下降的重要因素,而且子层屈曲主要是沿垂直载荷的方向(90°)扩展;对于准各向同性板,屈曲子层中与母层相邻的铺层的方向一般为90°。层合板的剩余压缩强度与板的冲击损伤面积无直接关系。      

三维六向编织复合材料力学性能的实验研究

通过拉伸 ( 含开孔拉伸 ) 、压缩 ( 含开孔压缩 ) 、面内剪切及冲击后压缩实验,获得了三维六向编织复合材料的主要力学性能参数。基于宏观实验,探讨了材料在拉伸、压缩及剪切载荷作用下的破坏模式和失效机理,分析了开孔类型 ( 机械孔、编织孔 ) 对材料拉、压性能的影响并研究了冲击对材料压缩性能的影响。所获结果为进一步研究三维六向编织复合材料的刚度、强度预报奠定了基础。