High-Temperature Environmental Stability of the Compounds in the Al2O3–Y2O3 System

Heat treatments in several environments were performed on a series of compounds in the Al₂O₃ and Y₂O₃ system: Al₂O₃Y₃Al₅O₁₂ eutectic, Y₃Al₅O₁₂, YAlO₃, Y₄Al₂O₉, and Y₂O₃. The yttrium aluminates were found to be stable at high temperatures under vacuum and in air. However, when they were heat-treated under vacuum in proximity to SiC, degradation was observed. This was found to be primarily a result of carbothermal reduction. In a similarly reducing environment without Si, the yttrium aluminates, and Al₂O₃ and Y₂O₃, all exhibited degradation by carbothermal reduction. Based upon the experimental results, a degradation mechanism for yttrium aluminates was proposed.     

Novel Deposition of Columnar Y3Al5O12 Coatings by Electrostatic Spray-Assisted Vapor Deposition

A novel and cost-effective electrostatic spray-assisted vapor deposition (ESAVD) was used to deposit Y₃Al₅O₁₂ (YAG) coatings. Polycrystalline single-phase Y₃Al₅O₁₂ coatings were synthesized using the ESAVD method in an open atmosphere at 650°C, and then annealed at 700°–900°C for 1 h. The ESAVD process involves the decomposition and chemical reactions of charged aerosol in vapor phase. The low-temperature coating deposition characteristics of the ESAVD process using a suitable sol precursor decreases the reaction and crystallization temperatures for forming Y₃Al₅O₁₂ coatings. The microstructure of the Y₃Al₅O₁₂ coating prepared using the ESAVD method is columnar and such strain-resistance microstructure could be useful for thermal barrier coating applications.     

Ternary System Al2O3—MgO—CaO: Part II, Phase Relationships in the Subsystem Al2O3—MgAl2O4—CaAl4O7

Solid-state compatibility and melting relationships in the subsystem Al₂O₃—MgAl₂O₄—CaAl₄O₇ were studied by firing and quenching selected samples located in the isopletal section (CaO·MgO)—Al₂O₃. The samples then were examined using X-ray diffractomtery, optical microscopy, and scanning and transmission electron microscopies with wavelength- and energy-dispersive spectroscopies, respectively. The temperature, composition, and character of the ternary invariant points of the subsystem were established. The existence of two new ternary phases (Ca₂Mg₂Al₂₈O₄₆ and CaMg₂Al₁₆O₂₇) was confirmed, and the composition, temperature, and peritectic character of their melting points were determined. The isothermal sections at 1650°, 1750°, and 1840°C of this subsystem were plotted, and the solid-solution ranges of CaAl₄O₇, CaAl₁₂O₁₉, MgAl₂O₄, Ca₂Mg₂Al₂₈O₄₆, and CaMg₂Al₁₆O₂₇ were determined at various temperatures. The experimental data obtained in this investigation, those reported in Part I of this work, and those found in the literature were used to establish the projection of the liquidus surface of the ternary system Al₂O₃—MgO—CaO.     

Phase Transition of Rare-Earth Aluminates (RE4Al2O9) and Rare-Earth Gallates (RE4Ga2O9)

Lattice parameters of RE₄Al₂O₉ (RE = Y, Sin, Eu, Gd, Tb, Dy, Ho, Er, Tm, and Yb) prepared at 1600–1800°C and those of RE₄Ga₂O₉ (RE = La, Pr, Nd, Sm, Eu, and Gd) prepared at 1400–1600°C were refined by Rietveld analysis for the X-ray powder diffraction patterns. The parameters increased linearly with the ionic radius of the trivalent rare-earth elements ( r _RE). High-temperature differential calorimetry and dilatometry revealed that both RE₄Al₂O, and RE₄Ga₂O, have reversible phase transitions with volume shrinkages of 0.5–0.7% on heating and thermal hystereses. The transition temperatures (7_tr) decreased from 1300°C (Yb) to 1044°C (Sm) for RE₄A1₂O₉, except for Y₄Al₂O₉ ( T_tr = 1377°C), and from 1417°C (Gd) to 1271°C (La) for RE₄Ga₂O, with increasing ionic radius of the rare-earth elements. These transition temperatures were plotted on a curve against the ionic radius ratio of Al³⁺ or Gd³⁺ and RE³⁺ ( r _A1Ga/r_RE) except for Y₄Al₂O₉.     

Eutectic Composition in the Pseudobinary of Y4Al2O9 and Y2O3

The eutectic composition between Y₄Al₂O₉ and Y₂O₃ was determined using electron probe microanalysis (EPMA) on directionally solidified specimens with hypo- and hypereutectic compositions. The microstructures of the specimens as a function of composition differ considerably with small deviation from the eutectic composition (70.5 mol% Y₂O₃ and 29.5 mol% Al₂O₃). Based on the current results and other published data, the pseudobinary system between Al₂O₃ and Y₂O₃ is revised.     

High-Strain-Rate Superplasticity in Y2O3-Stabilized Tetragonal ZrO2 Dispersed with 30 vol% MgAl2O4 Spinel

High-strain-rate superplasticity is attained in a 3-mol%-Y₂O₃-stabilized tetragonal ZrO₂ polycrystal (3Y-TZP) dispersed with 30 vol% MgAl₂O₄ spinel: tensile elongation at 1823 K reached >300% at strain rates of 1.7 × 10⁻²– 3.3 × 10⁻¹ s⁻¹. The flow behavior and the microstructure of this material indicate that the MgAl₂O₄ dispersion should enhance accommodation processes necessary for grain boundary sliding. Such an effect is assumed to arise from an enhancement of the cation diffusion by the dissolution of Al and Mg ions into the ZrO₂ matrix and from stress relaxation due to the dispersed MgAl₂O₄ grains.     

Thermochemistry of Glasses in the Y2O3-Al2O3-SiO2 System

Enthalpies of drop solution in molten 2PbO-B₂O₃ at 1078 K were measured for glasses along the 2YAlO₃-3SiO₂ and return ½Y₃Al₅O₁₂-3SiO₂ joins. The onset glass transition temperature increases slightly with increasing silica content and Y/Al. Enthalpies of mixing were calculated on the basis of amorphous end members. Strongly negative heats of mixing support the absence of miscibility gaps except possibly for very high silica content, consistent with experimental phase analyses, which indicate much narrower miscibility gaps compared with the phase diagrams calculated on the basis of previous data and the CALPHAD formalism.     

Effect of Heat Treatment on the Microstructure and Properties of Dense AIN Sintered with Y2O3 Additions

The secondary phase constitution in two sintered AIN ceramics (1.8% and 4.2% Y₂O₃ additions) was studied as a function of heat treatment temperatures between 1750° and 1900°C under pure nitrogen atmosphere. The effect of the phase constitution on the physical properties, such as density, thermal conductivity ( K ), and lattice constants, and on the mechanical properties in three-point bending, was also investigated. Y₃Al₅O₁₂ was found to getter dissolved oxygen from the AIN lattice below 1850°C, but evaporated at 1850°C and above. Y₄Al₂O₉ appeared to sublimate below 1850°C in the atmosphere used in this study. Depending on the secondary phase constitution, heat treatment affected thermal conductivity favorably or adversely. Occasionally, samples with similar lattice oxygen contents were found to have different thermal conductivities, suggesting that factors besides dissolved oxygen can also influence K . Lattice parameter measurements indicated that, within the small range of lattice oxygen concentrations in the AIN samples studied, the c-axis was more sensitive than the a -axis to oxygen content.     

Film Synthesis of Y3Al5O12 and Y3Fe5O12 by the Spray–Inductively Coupled Plasma Technique

Thin films of yttrium aluminum garnet (YAG, Y₃Al₅O₁₂) and yttrium iron garnet (YIG, Y₃Fe₅O₁₂) were synthesized on single-crystal Al₂O₃ substrates by a modification of spray pyrolysis using a high-temperature inductively coupled plasma at atmospheric pressure (spray–ICP technique). Using this technique, films could be grown at faster rates (0.12 μm/min for YAG and 0.10 μm/min for YIG) than using chemical vapor deposition (0.005–0.008 μm/min for YAG) or sputtering (0.003–0.005 μm/min for YIG). The films were dense and revealed a preferred orientation of (211). The growth of YIG was accompanied by coprecipitation of α-Fe₂O₃. The coprecipitation, however, could be largely suppressed by preliminary formation of a Y₂O₃ layer on the substrate.     

Formation of α-Si3N4 Solid Solutions in the System Si3N4-A1N-Y2O3

The subsolidus phase diagram of the quasiternary system Si₃N₄-AlN-Y₂O₃ was established. In this system α-Si₃N₄ forms a solid solution with 0.1Y₂O₃: 0.9 AIN. The solubility limits are represented by Y_0.33Si_10.5Al_1.5O_0.5N_15.5 and Y_0.67Si₉A1₃ON₁₅. At 1700°C an equilibrium exists between β-Si₃N₄ and this solid solution.     

Processing and Properties of in Situ-Reinforced α-SiAlONs Stabilized with Y2O3 and Lu2O3

α-SiAlONs with equiaxed and elongated microstructures stabilized with Y₂O₃ and Lu₂O₃ were produced by hot pressing, and the phase structure and room- and high-temperature mechanical properties were assessed. Additional liquid added to the starting composition in the form of 5 wt% rare-earth monosilicate resulted in the formation of elongated microstructures and improvements in room-temperature strength and fracture toughness. The elongated grain growth was promoted by the additional liquid phase, which crystallized to form a secondary grain-boundary phase thought to be J ' (Re₄Si_{2– x} Al _x O_{7+ x} N_{2– x} ). For the equiaxed and the elongated samples, those sintered with Lu₂O₃ showed higher hardness than the comparable Y₂O₃-sintered materials, and, at elevated temperature, the strength retention of the elongated Lu₂O₃ SiAlON was much higher than that of the Y₂O₃ sample, which was attributed to properties of the residual grain-boundary phase associated with the difference in the cationic radius of the stabilizing cation.     

Growth of Single-Crystal and Polycrystalline Thin Films of MgAl2O4 and MgFe2O4

Single-crystal and polycrystalline films of Mg-Al₂O₄ and MgFe₂O₄ were formed by two methods on cleavage surfaces of MgO single crystals. In one procedure, aluminum was deposited on MgO by vacuum evaporation. Subsequent heating in air at about 510°C formed a polycrystalline γ-Al₂O₈ film. Above 540°C, the γ-Al₂O, and MgO reacted to form a single-crystal MgAl₂O₄ film with {001} MgAl₂O₄‖{001} MgO. Above 590°C, an additional layer of MgAl₂O₄, which is polycrystalline, formed between the γ-Al₂O₃ and the single-crystal spinel. Polycrystalline Mg-Al₂O₄ formed only when diffusion of Mg²⁺ ions proceeded into the polycrystalline γ-Al₂O₃ region. Corresponding results were obtained for Mg-Fe₂O₄. MgAl₂O₄ films were also formed on cleaved MgO single-crystal substrates by direct evaporation, using an Al₂O₃ crucible as a source. Very slow deposition rates were used with source temperatures of ∼1350°C and substrate temperatures of ∼800°C. Departures from single-crystal character in the films may arise through temperature gradients in the substrate.     

Electrical Conduction in β-Bi2O3 Doped with Sb2O3

Electrical conduction in tetragonal β-Bi₂O₃ doped with Sb₂O₃ was investigated by measuring electrical conductivity, ionic transference number, and Seebeck coefficient. The β-Bi₂O₃ doped with 1 to 10 mol% Sb₂O₃ was stable up to 600°C and showed an oxygen ionic and electronic mixed conduction, where the electron conduction was predominant at low oxygen pressures. The oxygen-ion conductivity showed a maximum at 4 mol% Sb₂O₃, whereas the activation energy for the ionic conduction remained unchanged for 4 to 10 mol% Sb₂O₃-doped specimens. These results were interpreted in terms of the oxygen vacancy concentration and the distortion of the tetragonal structure. The electron conductivity and its oxygen pressure dependence decreased with increasing Sb₂O₃ content. The fact that Sb⁵⁺ is partially reduced by excess electrons in heavily doped β specimens at low oxygen pressures is explained.     

Improvement in Mechanical Properties of Powder-Processed MoSi2 by the Addition of Sc2O3 and Y2O3

Additions of 1-20 mol% Sc₂O₃ or Y₂O₃ to MoSi₂ eliminate glassy SiO₂, which improves mechanical properties at both ambient and high temperatures. In particular, only 1 mol% ScO₃ additions dramatically enhance three-point bending strength from 521 to 1081 MPa. Vickers hardness, Young's modulus, fracture toughness, and high-temperature strength are also improved by this low level of additive. The improvement of mechanical properties is attributed to the formation of crystalline silicates: Sc₂Si₂O₇, Y₂Si₂O₇, Y₂SiO₅, and Y₄Si₃O₁₂, which are analyzed by XRD, SEM-EDS, and TEM-EDS methods.     

Porous Glass-Ceramics with a Skeleton of the Fast-Lithium-Conducting Crystal Li1+xTi2−xAlx(PO4)3

Porous glass-ceramics with a skeleton of the fast-lithium-conducting crystal Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ (where x = 0.3–0.5) were prepared by crystallization of glasses in the Li₂O─CaO─TiO₂─Al₂O₃–P₂O₅ system and subsequent acid leaching of the resulting dense glass-ceramics composed of the interlocking of Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ and β-Ca₃(PO₄)₂ phases. The median pore diameter and surface area of the resulting porous Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ glass-ceramics were approximately 0.2 μm and 50 m²/g, respectively. The electrical conductivity of the porous glass-ceramics after heating in LiNO₃ aqueous solution was 8 × 10⁻⁵ S/cm at 300 K or 2 × 10⁻² S/cm at 600 K.     

Exsolution of β-Ga2O3 Crystalline Solutions in the System MgAl2O3-Ga2O3

The subsolidus phase equilibrium diagram for the pseudobinary join MgAl₂O₄-Ga₂O₃ was determined. The shape of the exsolution boundary was obtained by heat-treating samples pre- equilibrated at 1600°C. Crystalline solubility of Ga₂O₃ in MgAl₂O₄ decreased from 73 mole % at 1600°C to 55 mole % at 1200°C. The crystalline solution was formed by the replacement of Mg²⁺ions by Ga³⁺ ions to produce a cation defect spinel. The phase precipitated was the mono-clinic δ-Ga₂O₃ (=δ-Al₂O₃ structure). Changes in the ratios of relative X-ray diffraction intensities indicated that the crystalline solutions also disorder with temperature.     

Room-Temperature Strength and Fracture of ZrO2-Y2O3 Single Crystals

Strength and fracture toughness results are presented for ZrO₂ single crystals stabilized with Y₂O₃. The crystals (2 cm in diameter by 5 cm long) were prepared by skull melting. The partially stabilized compositions with 4 to 6 wt% Y₂O₃ showed a dramatic improvement in mechanical properties over the fully stabilized samples containing 20 wt% Y₂O₃, i.e. a strength exceeding 1000 MPa and a fracture toughness of 8 Mpa,.m ^1/2 were achieved compared to 200 MPa and 2 Mpa.m^1/2, respectively, for fully stabilized ZrO₂ single crystals.     

Interdiffusion in the System MgO-MgAl2O4

Interdiffusion coefficients in single-crystal MgO were determined using an MgO-MgAl₂O₄ diffusion couple. For a concentration of 1 mol% Al₂O₃ in MgO, the interdiffusion coefficient can be expressed as D =2.0±0.2 exp (−76,000±3,000/ RT ) for the MgO-MgAl₂O₄ couple. This relation compares well with previous measurements in the MgO-Al₂O₃ system. The interdiffusion coefficients, which increased with the mol fraction of cation vacancies, were in the range of 10⁻⁸ to 10⁻¹⁰ cm²s⁻¹ for the concentrations and temperatures studied. Diffusion was enhanced below 1640°C if powdered MgAl₂O₄ was used. Self-diffusion coefficients for Al³⁺ ions in MgO were calculated; Al³⁺ diffuses faster than Cr³⁺ in MgO.     

Near-Net Shape β-Si4Al2O2N6 Parts by Hydrolysis Induced Aqueous Gelcasting Process

In this paper, a new net-shaping process, an hydrolysis-induced aqueous gelcasting (GC) (GCHAS) has been reported for consolidation of β-Si₄Al₂O₂N₆ ceramics from aqueous slurries containing 48–50 vol%α-Si₃N₄, α-Al₂O₃, AlN, and Y₂O₃ powders mixture. Dense ceramics of same composition were also consolidated by aqueous GC and hydrolysis assisted solidification routes. Among three techniques used, the GCHAS process was found to be superior for fabricating defect-free thin wall β-Si₄Al₂O₂N₆ crucibles and tubes. Before use, the as purchased AlN powder was passivated against hydrolysis. The sintered β-Si₄Al₂O₂N₆ ceramics exhibited comparable properties with those reported for similar materials in the literature.     

Sequential Precipitation of MgAl2O4 on Mg1-x CaxAl2O4 in Hot-Pressed MgO Single Crystals

In a hot-pressed and deformed MgO single crystal, precipitates of Mg_1-xCa_xAl₂O₄ spinel upon which MgAl₂O₄ spinel subsequently precipitated were observed and analyzed using transmission electron microscopy and scanning electron microscopy. This behavior is related to the respective solubility limits of CaO and Al₂O₃ in MgO at the hot-pressing temperature and may be aided by impurity segregation to the dislocations. The spinel selectively precipitated at the nodes of a dislocation network which was formed during [001] hot-pressing deformation, as a result of the reaction b₃= b₁+ b₂= (1/2) [011] + (1/2)     = [001]. The dislocation is sessile, and the precipitates have a <100>_matrix≨ <100>_spinel coherent relationship.