Convective Heat Transfer Enhancement of a Rectangular Flat Plate by an Impinging Jet in Cross Flow

Experiments were carried out to study the heat transfer performance of an impinging jet in a cross flow. Several parameters including the jet-to-cross-flow mass ratio （X=2%-8%）, the Reynolds number （Red=1434-5735） and the jet diameter （d=2-4 mm） were explored. The heat transfer enhancement factor was found to increase with the jet-to-cross-flow mass ratio and the Reynolds number, but decrease with the jet diameter when other parameters maintain fixed. The presence of a cross flow was observed to degrade the heat transfer performance in respect to the effect of impinging jet to the target surface only. In addition, an impinging jet was confirmed to be capable of en-hancing the heat transfer process in considerable amplitude even though the jet was not designed to impinge on the target surface.     

Numerical Study of Heat Transfer and Fluid Flow in Multiple turbulent Impinging Jets

ABSTRACT

Impingement flows have been studied extensively for various geometries and configurations, but because of the complexity of the turbulent flow and its strong dependence on the geometry of the flow, further investigation is required to identify the suitable model for specific cases. This paper presents a study of various k–E turbulence models in order to identify the best model for an array of multiple confined impinging slot jets, with exhaust ports in the confinement surface located symmetrically between adjacent jets. Such a configuration is used in a novel drum dryer for black liquor. The “High Reynolds number” turbulence models including the standard k–E model fail to predict heat transfer to impingement surface accurately although they do predict the flow field reasonably well. On the other hand, the “Low Reynolds number” models yield considerably better results for both fluid flow and heat transfer. All computed results are compared with experimental data reponed in the literature. This work was motivated by the need to select an optimal multiple impinging jet configuration for a novel drum dryer for Kraft black liquor. It is also pertinent to impingement dryers for paper, films, textiles etc.     

圆形自由水射流冲击换热及喷嘴布置

引言 水射流冲击冷却由于具有较高的换热能力,广泛应用于机械和化工行业,以实现工件的快速冷却和控制工件的温度变化.在大型轴类工件(工件直径D=1000～3000 mm)喷水冷却装置中,多喷嘴圆孔自由水射流以特定阵列布置冲击至工件表面,相对短暂的沸腾换热结束后,阵列自由水射流即以强制对流方式实现工件冷却.因此,自由水射流冲击换热特性及多喷嘴布置形式对喷水冷却装置的结构设计至关重要.     

Flow and Heat Transfer Characteristics of Confined Noncircular Turbulent Impinging Jets

A three dimensional computational fluid dynamic investigation is carried out to predict the turbulent flow and surface heat transfer under an impinging air jet issuing normally from a single noncircular orifice in a plate held parallel to the target surface. Static pressure distributions, velocity fields and local as well as average Nusselt number on the impinged surface are presented for square, elliptic, and rectangular orifices and compared with those for a circular orifice. Effects of jet Reynolds number as well as spacing between the nozzle plate and the impinged surface are examined using a two-layer κ-η turbulence model. Results show flow structure similarities between the characteristics of rectangular and elliptic jets of equal aspect ratio. Further, it is observed that noncircular impinging jets can provide higher average heat transfer rates than corresponding circular jets for certain geometric parameters viz. nozzle-to-plate spacing and the size of the averaging area used to compute the average Nusselt number.     

Flow and Heat Transfer Characteristics of Confined Noncircular Turbulent Impinging Jets

Abstract

A three dimensional computational fluid dynamic investigation is carried out to predict the turbulent flow and surface heat transfer under an impinging air jet issuing normally from a single noncircular orifice in a plate held parallel to the target surface. Static pressure distributions, velocity fields and local as well as average Nusselt number on the impinged surface are presented for square, elliptic, and rectangular orifices and compared with those for a circular orifice. Effects of jet Reynolds number as well as spacing between the nozzle plate and the impinged surface are examined using a two-layer κ–η turbulence model. Results show flow structure similarities between the characteristics of rectangular and elliptic jets of equal aspect ratio. Further, it is observed that noncircular impinging jets can provide higher average heat transfer rates than corresponding circular jets for certain geometric parameters viz. nozzle-to-plate spacing and the size of the averaging area used to compute the average Nusselt number.     

Nanofluid impingement jet heat transfer

Experimental investigation to study the heat transfer between a vertical round alumina-water nanofluid jet and a horizontal circular round surface is carried out. Different jet flow rates, jet nozzle diameters, various circular disk diameters and three nanoparticles concentrations (0, 6.6 and 10%, respectively) are used. The experimental results indicate that using nanofluid as a heat transfer carrier can enhance the heat transfer process. For the same Reynolds number, the experimental data show an increase in the Nusselt numbers as the nanoparticle concentration increases. Size of heating disk diameters shows reverse effect on heat transfer. It is also found that presenting the data in terms of Reynolds number at impingement jet diameter can take into account on both effects of jet heights and nozzle diameter. Presenting the data in terms of Peclet numbers, at fixed impingement nozzle diameter, makes the data less sensitive to the percentage change of the nanoparticle concentrations. Finally, general heat transfer correlation is obtained verses Peclet numbers using nanoparticle concentrations and the nozzle diameter ratio as parameters.     

不同工作因数下方波冲击射流的换热特性

应用数值模拟方法研究了不同工作因数下方波冲击射流的换热及流动特性,并分析了冲击靶面换热特性的变化规律。研究了冲击靶面换热特性随Reynolds数、脉冲频率、喷嘴距冲击靶面距离与喷嘴直径之比等参数的变化规律,重点分析了不同工作因数对冲击射流滞止区域换热与流动特性的影响,并将数值计算结果与连续冲击射流、脉动冲击射流实验结果进行对比验证。计算结果表明:当工作因数为0.5与0.7时,冲击靶面滞止区域Nusselt数非常接近;当工作因数为0.5时,壁面射流区域Nusselt数比工作因数为0.7时提高了10%;工作因数为0.9时,冲击靶面Nusselt数比连续冲击射流提高3%;工作因数为0.7时,相对于工作因数为0.5、0.9及连续冲击射流时,冲击靶面滞止区域存在强烈的涡结构变化。     

Highly selective fluorescent chemosensor for Zn2+ derived from inorganic-organic hybrid magnetic core/shell Fe3O4@SiO2 nanoparticles

Experimental investigation to study the heat transfer between a vertical round alumina-water nanofluid jet and a horizontal circular round surface is carried out. Different jet flow rates, jet nozzle diameters, various circular disk diameters and three nanoparticles concentrations (0, 6.6 and 10%, respectively) are used. The experimental results indicate that using nanofluid as a heat transfer carrier can enhance the heat transfer process. For the same Reynolds number, the experimental data show an increase in the Nusselt numbers as the nanoparticle concentration increases. Size of heating disk diameters shows reverse effect on heat transfer. It is also found that presenting the data in terms of Reynolds number at impingement jet diameter can take into account on both effects of jet heights and nozzle diameter. Presenting the data in terms of Peclet numbers, at fixed impingement nozzle diameter, makes the data less sensitive to the percentage change of the nanoparticle concentrations. Finally, general heat transfer correlation is obtained verses Peclet numbers using nanoparticle concentrations and the nozzle diameter ratio as parameters.     

Pulsating Jet Impingement Heat Transfer Enhancement

This article presents results from a numerical study of pulsating jet impingement heat transfer. The motivation is to seek conditions offering a significant enhancement compared to steady flow impingement drying. The CFD software package FLUENT was used for simulating slot-type pulsating jet impingement flows with confinement. The parameter study included velocity amplitude ratio, mean jet velocity, and pulsation frequency. The distance from nozzle exit to surface was three times the hydraulic diameter of the nozzle. The Reynolds number based on the nozzle hydraulic diameter and jet temperature was 2,460 with a mean jet velocity of 30 m/s, which is the base case of the numerical experiments. Results showed that time-averaged surface heat transfer increased with increasing velocity amplitude for the same mean jet velocity. Large velocity amplitudes helped enhance heat transfer by two mechanisms: high jet velocity during the positive cycle and strong recirculating flows during the negative cycle. For the cases with different mean jet velocities but the same maximum velocity, time-averaged surface heat flux decreased with decreasing mean jet velocity. As for the effects of pulsation frequency, with high-velocity amplitude ratio, time-averaged surface heat fluxes were at the same level regardless of frequency. However, at low-velocity amplitude ratio, high frequency caused stronger recirculating flows resulting in greater heat transfer compared to the cases with a lower frequency.     

Pulsating Jet Impingement Heat Transfer Enhancement

This article presents results from a numerical study of pulsating jet impingement heat transfer. The motivation is to seek conditions offering a significant enhancement compared to steady flow impingement drying. The CFD software package FLUENT was used for simulating slot-type pulsating jet impingement flows with confinement. The parameter study included velocity amplitude ratio, mean jet velocity, and pulsation frequency. The distance from nozzle exit to surface was three times the hydraulic diameter of the nozzle. The Reynolds number based on the nozzle hydraulic diameter and jet temperature was 2,460 with a mean jet velocity of 30 m/s, which is the base case of the numerical experiments. Results showed that time-averaged surface heat transfer increased with increasing velocity amplitude for the same mean jet velocity. Large velocity amplitudes helped enhance heat transfer by two mechanisms: high jet velocity during the positive cycle and strong recirculating flows during the negative cycle. For the cases with different mean jet velocities but the same maximum velocity, time-averaged surface heat flux decreased with decreasing mean jet velocity. As for the effects of pulsation frequency, with high-velocity amplitude ratio, time-averaged surface heat fluxes were at the same level regardless of frequency. However, at low-velocity amplitude ratio, high frequency caused stronger recirculating flows resulting in greater heat transfer compared to the cases with a lower frequency.     

Effect of Surface Motion on Transport Processes Due to Circular Impinging Jets—A Numerical Study

This article presents a numerical study of transport phenomena under impinging circular jet banks over a moving surface by solving three-dimensional Navier-Stokes equation in both the laminar and the turbulent regime. A periodic element of the jet bank was used with jet pitch of 10d, span of target surface as 10d, and jet height of 2d, where d is the jet diameter. For the turbulent closure, a realizable k-ε model was used. The distributions of the Nusselt number and the skin friction coefficients were computed from the analyzed data. The surface velocity was found to influence strongly the flow structure over the impinging surface, leading to reduction in heat transfer.     

Numerical Study on the Effect of Cross-Flow on Turbulent Flow and Heat Transfer Characteristics Under Normal and Oblique Semi-confined Impinging Slot Jets

Impinging jets are commonly used in industrial dryers and electronics chip cooling. Since in industrial practice it is necessary to use multiple jets, the interaction between jets can have important effect on their heat transfer performance. Hence, the study of cross-flow caused by the spent flow of upstream jets is obviously significant. In this study, a computational fluid dynamics simulation was carried out of the flow and heat transfer characteristics for a single semi-confined turbulent slot jet of air impinging normally or obliquely into an imposed air cross-flow of the same or different temperature. The standard k-ε and the Reynolds stress models were used. Effects of the various flow parameter (e.g., jet-to-cross-flow mass ratio) and geometric parameters (e.g., nozzle-to-target spacing and jet angle) were evaluated at a fixed Reynolds number (11,000 and 12,000) for equal and unequal temperatures of the jet and cross-flow. Results indicate the significant degradation of the impingement heat transfer rates due to cross-flow and a relatively minor influence of the temperature difference between the jet and cross-flow over the ranges of parameters studied. Both the turbulence models produced comparable Nusselt number distributions along the impingement surface.     

Effect of Surface Motion on Transport Processes Due to Circular Impinging Jets—A Numerical Study

This article presents a numerical study of transport phenomena under impinging circular jet banks over a moving surface by solving three-dimensional Navier-Stokes equation in both the laminar and the turbulent regime. A periodic element of the jet bank was used with jet pitch of 10d, span of target surface as 10d, and jet height of 2d, where d is the jet diameter. For the turbulent closure, a realizable k-ε model was used. The distributions of the Nusselt number and the skin friction coefficients were computed from the analyzed data. The surface velocity was found to influence strongly the flow structure over the impinging surface, leading to reduction in heat transfer.     

A Numerical Study on the Convective Heat Transfer Characteristics of Pulsed Impingement Drying

Impinging jets issuing from the tailpipe of pulse combustors have been evaluated in recent studies for possible applications in rapid drying of continuous sheets such as grades of paper, textiles, etc. In order to further understand the effect of pulsed flows on the heat and mass transfer rates of impinging jets, a numerical study was performed on a two-dimensional pulsating impinging jet array. A computational fluid dynamics approach was used to examine the effect of periodic sinusoidal pulsation on the local Nusselt number distribution of the wet target surface being dried. Because a high temperature and large temperature difference between the jet flow and impingement surface are used to obtain high heat transfer rates in impingement drying, the thermophysical properties of jet flows were taken into account in the present mathematical model. A parametric study including phase angle and frequency as well as amplitude of pulsating flows was conducted for optimization and design of pulsating jet arrays. Examination of the velocity and thermal fields showed that the instantaneous heat transfer rate on the target surface was highly dependent on the mass transfer characteristic and development of the hydrodynamic boundary layer with time.     

CFD study of turbulent jet impingement on curved surface

The heat transfer and flow characteristics of air jet impingement on a curved surface are investigated with computational fluid dynamics(CFD)approach.The first applied model is a one-equation SGS model for large eddy simulation(LES)and the second one is the SST-SAS hybrid RANS-LES.These models are utilized to study the flow physics in impinging process on a curved surface for different jet-to-surface(h/B)distances at two Reynolds numbers namely,2960 and 4740 based on the jet exit velocity(U_e)and the hydraulic diameter(2B).The predictions are compared with the experimental data in the literature and also the results from RANS k-εmodel.Comparisons show that both models can produce relatively good results.However,one-equation model(OEM)produced more accurate results especially at impingement region at lower jet-to-surface distances.In terms of heat transfer,the OEM also predicted better at different jet-to-surface spacings.It is also observed that both models show similar performance at higher h/B ratios.     

Numerical Study on the Effect of Cross-Flow on Turbulent Flow and Heat Transfer Characteristics Under Normal and Oblique Semi-confined Impinging Slot Jets

Abstract

Impinging jets are commonly used in industrial dryers and electronics chip cooling. Since in industrial practice it is necessary to use multiple jets, the interaction between jets can have important effect on their heat transfer performance. Hence, the study of cross-flow caused by the spent flow of upstream jets is obviously significant. In this study, a computational fluid dynamics simulation was carried out of the flow and heat transfer characteristics for a single semi-confined turbulent slot jet of air impinging normally or obliquely into an imposed air cross-flow of the same or different temperature. The standard k?ε and the Reynolds stress models were used. Effects of the various flow parameter (e.g., jet-to-cross-flow mass ratio) and geometric parameters (e.g., nozzle-to-target spacing and jet angle) were evaluated at a fixed Reynolds number (11,000 and 12,000) for equal and unequal temperatures of the jet and cross-flow. Results indicate the significant degradation of the impingement heat transfer rates due to cross-flow and a relatively minor influence of the temperature difference between the jet and cross-flow over the ranges of parameters studied. Both the turbulence models produced comparable Nusselt number distributions along the impingement surface.     

狭槽式空气喷流冲击于旋转圆柱体侧面的换热特性

利用实验方法探讨旋转圆柱体受狭槽式空气喷流的换热特性,圆柱体的高度与直径为定值,变动参数为（1）喷流Reynolds数（Re_j）、（2）旋转Reynolds数（Re_r）、（3）圆柱体直径（D）与喷嘴宽度（w）的比例（D/w）、（4）相对喷流冲击距离 （L/w,L为喷嘴距圆柱体的最近距离）等。实验结果显示平均Nusselt数（Nu）随Re_j与Re_r增大而提升,而D/w增加会使Nu减小,且D/w对Nu的影响将随L/w增大而衰退,且存在一临界L/w值能产生最高的Nu,且临界L/w值将随D/w增大而增大,最后,提出合理而准确的经验公式。     

Impingement heat transfer under a confined slot jet. Part I: Effect of surface throughflow

Local and average heat transfer coefficients were measured for a confined turbulent slot jet impinging on a permeable surface at which there may be throughflow. Local Nusselt number was obtained using a unique porous sensor designed for measurement of local heat transfer at a permeable surface which is subjected to rapidly and widely varying heat transfer. Measurements were performed for a wide range of jet Reynolds number and throughflow rates. Convective heat transfer coefficients was found to be enhanced by throughflow, and the enhancement factor in terms of Stanton number to be independent of jet Reynolds number and of extent of heat transfer area.     

同心环形管强迫流动与传热实验研究

在高温高压沸腾二相流实验系统上,实验研究了窄缝为2.05 mm的同心环形管,在不同加热条件下水的流动阻力与传热特性。2种加热方式为单内管或单外管电加热,通过处理实验测量的管壁温度获得传热系数。得到了以下结果:层流向紊流转变的临界雷诺数为2 300;环形管内的流动阻力系数小于普通圆管,外管加热时的摩擦系数小于非加热条件时的数值;窄缝环形管内换热有一定强化,高于相同条件下的圆管内紊流换热;内外管同时加热时,相比仅外管加热而言,外管的换热得到了抑制;得到了环形管内流动摩擦阻力系数与传热系数的实验关联式。     

Impingement Heat Transfer for a Cluster of Laminar Impinging Jets Issuing from Noncircular Nozzles

Abstract:

Results of numerical simulation of the flow and heat transfer characteristics for a semi-confined cluster of laminar air jets impinging normally on a plane wall are presented. A central jet is surrounded by four equally spaced jets of the same configuration. Both circular and noncircular nozzles are considered. The nozzle footprint is displayed in the static pressure, temperature, and local Nusselt number contours on the impingement surface only for relatively short nozzle-to-surface distances. The heat transfer characteristics and performance of circular and noncircular nozzles are compared. It is observed that the Nusselt number based on property values at the jet temperature is relatively insensitive to the temperature difference between the jet and the impingement surface. Also, the local Nusselt numbers are independent of the thermal boundary condition; i.e., the values are nearly the same for both isothermal and uniform heat flux conditions at the target surface. Finally, Nusselt numbers for a single equivalent jet viz. one with the same area as the five nozzles in the cluster combined, are compared for the case of the circular jet.