Preparation and characterization of acrylonitrile–styrene–methylmethacrylate terpolymer as a compatibilizer for rubber blends

Acrylonitrile‐co‐styrene‐co‐methylmethacrylate (AN‐S‐MMA) terpolymer was prepared by bulk and emulsifier‐free emulsion polymerization techniques. The bulk and emulsion terpolymers were characterized by means of Fourierr transform infrared spectroscopy, ¹³C nuclear magnetic resonance (NMR) spectroscopy, gel permeation chromatography, thermal gravimetric analysis, and elemental analysis. The kinetics of the terpolymerization were studied. The terpolymers were then incorporated into butadiene—acrylonitrile rubber (NBR)/ethylene propylene diene monomer rubber (EPDM) blends and into chloroprene rubber (CR)/EPDM blend. The terpolymers were then tested for potential as compatibilizers by using scanning electron microscopy and differential scanning calorimetry. The terpolymers improved the compatibility of CR/EPDM and NBR/EPDM blends. The physicomechanical properties of CR/EPDM and NBR/EPDM blend vulcanizates revealed that the incorporation of terpolymers was advantageous, since they resulted in blend vulcanizates with higher 100% moduli and with more thermally stable mechanical properties than the individual rubbers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3143–3153, 2003     

Study on the milling behavior of chloroprene rubber blends with ethylene–propylene–diene monomer rubber,polybutadiene rubber,and natural rubber

The viscoelastic properties of the blends of chloroprene rubber (CR) with ethylene–propylene–diene monomer rubber (EPDM), polybutadiene rubber (BR), and natural rubber (NR) at different temperature were studied using rubber processing analyzer (RPA). Mooney viscosities of compounds were measured and tight milling and sheeting appearance were observed on a two‐roll mill. The results showed that Mooney viscosities and the elastic modulus of the blends decreased with the increase of the temperature from 60 to 100°C. And the decreasing trends of pure CR, pure NR, and CR/NR blend compounds were more prominent than that of pure EPDM, pure BR, CR/EPDM, and CR/BR blend compounds. For CR/EPDM blend compounds, the decreasing trend became slower with the increase of EPDM ratio in the blend. Compared with pure CR, pure NR and CR/NR blend compounds, pure EPDM, pure BR compounds, and the blend compounds of CR/EPDM and CR/BR showed less sensibility to temperature and they were less sticky to the metal surface of rolls and could be kept in elastic state at higher temperature, easy to be milled up and sheeted. At the same blend ratio and temperature, the property of tight milling of the blends decreased in the sequence of CR/EPDM, CR/BR, and CR/NR. With the increase of EPDM, BR, or NR ratio in CR blends, its property of tight milling was improved. POLYM. COMPOS., 28:667–673, 2007. © 2007 Society of Plastics Engineers     

Electrical and mechanical properties of grafted and ungrafted polyacrylamide–rubber blends

A systematic dielectric and mechanical study was carried out on an ethylene propylene diene monomer (EPDM) and a nitrile rubber (NBR) blended with polyacrylamide (PAM). From the compatibility investigations, it was found that EPDM/PAM is incompatible while NBR/PAM is semicompatible. To overcome the problem of phase separation between rubber and PAM, PAM was grafted with two different monomers, acrylonitrile (AN) and acrylic acid (AA), and added with 10 phr to both EPDM and NBR. Poly(vinyl chloride) (PVC) was also added as a compatiblizing agent to both types of blend. It was concluded that the addition of either a grafted polymer or PVC to the rubber–plastic blend could improve to some extent the compatibility of such blends. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 2053–2059, 1998     

Preparation and characterization of polymethyltrifluoropropylsilicone modified acrylonitrile–butadiene rubber/fluorosilicon rubber blend

The blending of polymethyltrifluoropropylsilicone‐modified acrylonitrile–butadiene rubber (MNBR) and fluorosilicon rubber (FSR) at 70 : 30 ratio was investigated. The grafting of mercapto‐functionalized polymethyltrifluoropropylsilicone onto acrylonitrile‐butadiene rubber (NBR) by thiol‐ene reaction was carried out with 2,2′‐azobisisobutyronitrile as initiator in a Haake torque rheometer. The rheological properties of NBR grafting obtained at varying dosages of polymethyltrifluoropropylsilicone in a Haake torque rheometer were studied using torque curves. Grafting reaction was confirmed by ¹H nuclear magnetic resonance and energy‐dispersive X‐ray spectroscopy. Results of scanning electron microscopy and dynamic mechanical analysis showed better compatibility of MNBR/FSR blend than NBR/FSR reference blend. Meanwhile, the macro‐mechanical properties of the blend significantly improved. The tensile strength and tear strength of MNBR/FSR blend were improved to 14.34 MPa and 44.94 KN/m, respectively, which were 2.92 MPa and 13.03 KN/m higher than those of NBR/FSR reference blend. The low‐temperature brittleness of the blend was improved to ?57°C, an increase of ?6°C compared with that of NBR. These results indicated that MNBR/FSR blend at 70 : 30 ratio had improved compatibility because of the grafting chains that acted as interfacial agents. The low‐temperature resistance of the blend was also enhanced. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42328.     

Effects of trans‐polyoctylene rubber on rheological and green tensile properties of natural rubber/acrylonitrile–butadiene rubber blends

The influence of trans‐polyoctylene rubber (TOR) on the flow property, die swell behaviour and green tensile property of NR (natural rubber)/NBR (acrylonitrile–butadiene rubber) blend compound was investigated as a function of TOR loading level. The pure TOR, NR and NBR compounds were also investigated for comparison with the blend compounds. The shear viscosity of TOR strongly depended on the temperature as well as shear rate. The viscosity of the NR/NBR blend compound was even lower than that of the constituent components at relatively lower shear rates, and the viscosity difference became smaller as the shear rate was increased. The viscosity of the NR/NBR blend compounds was strongly affected by the addition of TOR but the effect became negligible with increasing the shear rate. Both the die‐swell ratio and the surface topology of extrudates were also affected by TOR addition; the dependence on shear rate was much stronger for higher TOR level. The NR/NBR blend compound showed much higher green tensile strength and elongation at break than those of the constituent components. Both the green tensile modulus and strength of the NR/NBR blend compound were greatly enhanced, while the elongation at break was reduced with the addition of TOR. © 2002 Society of Chemical Industry     

Thermal and mechanical properties of silicon rubber/cis‐polybutadiene rubber/ethylene–propylene–diene monomer blends

Considering the properties of silicon rubber, ethylene–propylene–diene monomer (EPDM), and cis‐polybutadiene rubber (BR), a blend made by a new method was proposed in this article; this blend had thermal resistance and good mechanical properties. The morphology of the blend was studied by SEM, and it was found that the adhesion between the phases of BR, EPDM, and polysiloxanes (silicon rubber) could be enhanced, and the compatibility and covulcanization were good. The influence of the mass ratio of peroxide and silica on the mechanical properties and thermal resistance of the blend was studied. The results showed that the mechanical properties and thermal resistance of the blend were improved when silicon rubber/BR/EPDM was 20/30/50, dicumyl peroxide/sulfur was 2.5/2.5, and the amount of silica was 80 phr. The integral properties of rubber blend had more advantages than did the three rubbers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4462–4467, 2006     

Influences of trans‐polyoctylene rubber on the physical properties and phase morphology of natural rubber/acrylonitrile–butadiene rubber blends

The influence of trans‐polyoctylene rubber (TOR) on the mechanical properties, glass‐transition behavior, and phase morphology of natural rubber (NR)/acrylonitrile–butadiene rubber (NBR) blends was investigated. With an increased TOR level, hardness, tensile modulus, and resilience increased, whereas tensile strength and elongation at break tremendously decreased. According to differential scanning calorimetry and dynamic mechanical analysis, there were two distinct glass‐transition temperatures for a 50/50 NR/NBR blend, indicating the strongly incompatible nature of the blend. When the TOR level was increased, the glass transition of NBR was strongly suppressed. NBR droplets of a few micrometers were uniformly dispersed in the continuous NR phases in the NR/NBR blends. When TOR was added to a 50/50 NR/NBR blend, TOR tended to be located in the NR phase and in some cases was positioned at the interfaces between the NBR and NR phases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 125–134, 2002     

Effect of adhesive‐coated glass fiber in natural rubber (NR), acrylonitrile rubber (NBR), and ethylene–propylene–diene rubber (EPDM) formulations. I. Effect of adhesive‐coated glass fiber on the curing and tensile properties of NR,NBR, and EPDM formulations

Adhesive‐coated glass fibers (3 and 6 mm in length) were added at loadings of 10, 20, and 30 phr in natural rubber (NR), nitrile rubber (NBR), and ethylene–propylene–diene comonomer (EPDM) formulations in both plain and carbon black mixes. The compounds were mixed in a two‐roll mill and were characterized for their cure properties, tensile, tear, and Mullin's effect. In NR mixes, all of the formulations showed reversion in cure behavior, suggesting that NR remained unaffected. In NBR and EPDM mixes, almost all of the mechanical properties of the fiber improved. The result was more significant in EPDM than in NBR. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1111–1123, 2004     

Effect of anhydride‐modified ethylene–propylene–diene rubber and ethylene–vinyl acetate copolymers on the compatibilization of nitrile rubber/ethylene–propylene–diene rubber blends

The effects of maleic anhydride modified ethylene–propylene–diene rubber (EPDMMA) and maleic anhydride modified ethylene–vinyl acetate (EVAMA) on the compatibilization of nitrile rubber (NBR)/ethylene–propylene–diene rubber (70:30 w/w) blends vulcanized with a sulfur system were investigated. The presence of EPDMMA and EVAMA resulted in improvements of the tensile properties, whereas no substantial change was detected in the degree of crosslinking. The blend systems were also analyzed with scanning electron microscopy and dynamic mechanical thermal analysis. The presence of EVAMA resulted in a blend with a more homogeneous morphology. The compatibilizing effect of this functional copolymer was also detected with dynamic mechanical analysis. A shift of the glass‐transition temperature of the NBR phase toward lower values was observed. The presence of EPDMMA and EVAMA also increased the thermal stability, as indicated by an improvement in the retention of the mechanical properties after aging in an air‐circulating oven. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2408–2414, 2003     

Dynamic mechanical analysis of ethylene–propylene–diene monomer rubber and styrene–butadiene rubber blends

The effects of blend ratio, crosslinking systems, and fillers on the viscoelastic response of ethylene–propylene–diene monomer (EPDM)/styrene–butadiene rubber (SBR) blends were studied as functions of frequency, temperature, and cure systems. The storage modulus decreased with increasing SBR content. The loss modulus and loss tangent results showed that the EPDM/SBR blend vulcanizate containing 80 wt % EPDM had the highest compatibility. Among the different cure systems studied, the dicumyl peroxide cured blends exhibited the highest storage modulus. The reinforcing fillers were found to reduce the loss tangent peak height. The blend containing 40 wt % EPDM showed partial miscibility. The dispersed EPDM phase suppressed the glass‐transition temperature of the matrix phase. The dynamic mechanical response of rubbery region was dominated by SBR in the EPDM–SBR blend. The morphology of the blend was studied by means of scanning electron microscopy. The blend containing 80 wt % EPDM had small domains of SBR particles dispersed uniformly throughout the EPDM matrix, which helped to toughen the matrix and prevent crack propagation; this led to enhanced blend compatibility. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

丁腈橡胶/三元乙丙橡胶并用胶的制备及性能

将丁腈橡胶(NBR)与三元乙丙橡胶(EPDM)并用,考察了生胶牌号、并用比、并用工艺对NBR/EPDM并用胶性能的影响,并对其耐臭氧及耐油性能进行了分析.结果表明,选用第三单体为亚乙基降冰片烯(即E型)的EPDM可以改善其与NBR的共硫化性能;当门尼黏度相近的NBR与EPDM的并用比(质量比)为70/30,且采用2种生胶先混炼,而后加入各种配合剂的制备工艺,并用胶具有良好的耐臭氧性能及物理机械性能;具有以NBR为连续相、EPDM为分散相结构形态的并用胶有较好的耐油性能与良好的耐臭氧性能.     

Physical studies of foamed reinforced rubber composites Part I. Mechanical properties of foamed ethylene–propylene–diene terpolymer and nitrile–butadiene rubber composites

Reinforced ethylene–propylene–diene terpolymer (EPDM) and nitrile–butadiene rubber (NBR) blends were compounded with different concentrations of azodicarbonamide (ADC/K) foaming agent to obtain foamed EPDM and NBR composites. The mechanical properties under compression and under extension at different temperatures were measured for these foams. It was found that the increase of foaming agent concentration and temperature affect all the mechanical parameters. The obtained stress–strain data are discussed in the light of the continuum mechanics theory for compressible materials. © 2002 Society of Chemical Industry     

Effect of adhesive‐coated glass fiber in natural rubber (NR), acrylonitrile rubber (NBR), and ethylene–propylene–diene rubber (EPDM) formulations. II. Effect of cyclic loading,abrasion, and accelerated aging

Treated glass fibers (RICS, 3 and 6 mm in length) were added at a concentrations of 10, 20, and 30 phr in natural rubber (NR), nitrile rubber (NBR), and ethylene–propylene–diene comonomer (EPDM) formulations, in both plain and carbon black mixes. The compounds were mixed in two‐roll mill and were evaluated for their resistance to hot‐air aging, abrasion, compression set, Goodrich heat buildup, De Mattia fatigue, and for NR mixes, adhesion in the tensile mode. The vulcanizates of the three rubbers showed resistance to hot‐air aging. Abrasion resistance was poor for NR, and it improved with carbon black addition in the presence of treated glass fiber in NBR. In carbon‐black‐added EPDM vulcanizates, the abrasion resistance and fatigue resistance were better. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1124–1135, 2004     

Properties and morphologies of elastomer blends modified with EPDM‐g‐poly[2‐dimethylamino ethylmethacrylate]

The graft copolymerization of 2‐dimethylamino ethylmethacrylate (DMAEMA) onto ethylene propylene diene mononer rubber (EPDM) was carried out in toluene via solution polymerization technique at 70°C, using dibenzoyl peroxide as initiator. The synthesized EPDM rubber grafted with poly[DMAEMA] (EPDM‐g‐PDMAEMA) was characterized with ¹H‐NMR spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The EPDM‐g‐PDMAEMA was incorporated into EPDM/butadiene acrylonitrile rubber (EPDM/NBR) blend with different blend ratios, where the homogeneity of such blends was examined with scanning electron microscopy and DSC. The scanning electron micrographs illustrate improvement of the morphology of EPDM/NBR rubber blends as a result of incorporation of EPDM‐g‐PDMAEMA onto that blend. The DSC trace exhibits one glass transition temperature (T_g) for EPDM/NBR blend containing EPDM‐g‐PDMAEMA, indicating improvement of homogeneity. The physico‐mechanical properties after and before accelerated thermal aging of the homogeneous, and inhomogeneous EPDM/NBR vulcanizates with different blend ratios were investigated. The physico‐mechanical properties of all blend vulcanizates were improved after and before accelerated thermal aging, in presence of EPDM‐g‐PDMAEMA. Of all blend ratios under investigation EPDM/NBR (75/25) blend possesses the best physico‐mechanical properties together with the best (least) swelling (%) in brake fluid. Swelling behavior of the rubber blend vulcanizates in motor oil and toluene was also investigated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of the addition of acrylonitrile/ethylene–propylene–diene monomer (EPDM)/styrene graft copolymer on the morphology–properties relationships in poly(styrene‐co‐acrylonitrile)/EPDM rubber blends

Blends of poly(styrene‐co‐acylonitrile) (SAN) with ethylene–propylene–diene monomer (EPDM) rubber were investigated. An improved toughness–stiffness balance of the SAN/EPDM blend was obtained when an appropriate amount of acrylonitrile–EPDM–styrene (AES) graft copolymer was added, prepared by grafting EPDM with styrene–acrylonitrile copolymer, and mixed thoroughly with both of the two components of the blend. Morphological observations indicated a finer dispersion of the EPDM particles in the SAN/EPDM/AES blends, and particle size distribution became narrower with increasing amounts of AES. Meanwhile, it was found that the SAN/EPDM blend having a ratio of 82.5/17.5 by weight was more effective in increasing the impact strength than that of the 90/10 blend. From dynamic mechanic analysis of the blends, the glass‐transition temperature of the EPDM‐rich phase increased from ?53.9 to ?46.2°C, even ?32.0°C, for the ratio of 82.5/17.5 blend of SAN/EPDM, whereas that of the SAN‐rich phase decreased from 109.2 to 108.6 and 107.5°C with the additions of 6 and 10% AES copolymer contents, respectively. It was confirmed that AES graft copolymer is an efficient compatibilizer for SAN/EPDM blend. The compatibilizer plays an important role in connecting two phases and improving the stress transfer in the blends. Certain morphological features such as thin filament connecting and even networking of the dispersed rubber phase may contribute to the overall ductility of the high impact strength of the studied blends. Moreover, its potential to induce a brittle–ductile transition of the glassy SAN matrix is considered to explain the toughening mechanism. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1685–1697, 2004     

DMA analysis of the damping of ethylene–vinyl acetate/acrylonitrile butadiene rubber blends

The mechanical and damping properties of blends of ethylene–vinyl acetate rubber (VA content > 40% wt) (EVM)/acrylonitrile butadiene rubber (NBR), with 1.4 phr BIPB [bis (tert‐butyl peroxy isopropyl) benzene] as curing agent, were investigated by DMA and DSC. The effect of chlorinated polyvinyl chloride (CPVC), silica, carbon black, and phenolic resin (PF) as a substitute curing agent, on the damping and mechanical properties of EVM/NBR blends were studied. The results showed that 10 phr CPVC did not contribute to the damping of EVM700/NBR blends; Silica could dramatically improve the damping of EVM700/NBR blends because of the formation of bound rubber between EVM700/NBR and silica, which appeared as a shoulder tan δ peak between 20 and 70°C proved by DMA and DSC. This shoulder tan δ peak increased as the increase of the content of EVM in EVM/NBR blends. The tensile strength, modulus at 100% and tear strength of the blend with SiO₂ increased while the elongation at break and hardness decreased comparing with the blend with CB. PF, partly replacing BIPB as the curing agent, could significantly improve the damping of EVM700/NBR to have an effective damping temperature range of over 100°C and reasonable mechanical properties. Among EVM600, EVM700, and EVM800/NBR/silica blend system, EVM800/NBR/silica blend had the best damping properties. The EVM700/NBR = 80/10 blend had a better damping property than EVM700/NBR = 70/20. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Composites based on CB/CF/Ag filled EPDM/NBR rubber blends with high conductivity

For many applications of conductive rubbers, it is desirable to endow the conductive rubber with high conductivity at low conductive filler loading. In this work, composites based on ethylene‐propylene‐diene monomer (EPDM) rubber and nitrile‐butadiene rubber (NBR) were prepared using carbon blacks, carbon fibers, and silver powders as fillers. As the weight fraction of silver powder increased, the hardness of composites increased gradually while the tensile strength and elongation at break decreased. SEM revealed that the EPDM/NBR blends exhibited a relatively co‐continuous morphology. The differential scanning calorimetry (DSC) curves reported the EPDM/NBR rubber blends were incompatibility. The thermogravimetry (TG) studies showed that adding a small amount of silver powder could improve the thermal stability of composites. These conductive composites exhibited good electrical property. At room temperature, when the total volume fraction of fillers was 15.20%, the volume resistivity of EPDM/NBR blend was only 0.0058 Ω cm. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41357.     

丁腈橡胶/乙丙橡胶并用胶性能的研究

研究丁腈橡胶(NBR)/三元乙丙橡胶(EPDM)并用比对力学性能、老化性能和耐油性能的影响以及增容剂对共混胶性能的影响.结果表明,在NBR/EPDM共混胶中随EPDM用量的增加,硫化胶的硬度、拉伸强度、撕裂强度和定伸应力呈现下降趋势、拉断伸长率及耐低温性能有所改善,降低了NBR的耐汽油性能,但提高了耐含乙醇汽油性能.随着增容剂CM用量的增加,硫化胶拉伸强度、撕裂强度、100％定伸应力及硬度都呈增大趋势,采用扫描电镜可以清晰的看到添加CM改性后NBR/EPDM共混胶相容性得到显著改善.     

Nanomodified fillers in chloroprene‐rubber‐compatibilized natural rubber/acrylonitrile–butadiene rubber blends

Because of the structural dissimilarity, natural rubber (NR) and acrylonitrile–butadiene rubber (NBR) are immiscible, and compatibilizers are used during their blending. Neoprene or chloroprene rubber (CR) has a polar chlorine part and a nonpolar hydrocarbon part. Also, it has many advantageous properties, such as oil resistance, toughness, a dynamic flex life, and adhesion capacity. Hence, it is not less scientific to use CR as a compatibilizer in the blending of NBR with NR. Because many fewer studies on the use of neoprene as a compatibilizer in NR–NBR blend preparation are available, efforts were made to prepare 20:80 NR–NBR blends with CR with the aim of studying the effect of poly(ethylene oxide) (PEO)‐coated nano calcium silicate along with nano N‐benzylimine aminothioformamide and stearic acid coated nano zinc oxide in the sulfur vulcanization of the blends. The optimum dosage of the compatibilizer was derived by the determination of the tensile properties, tear resistance, abrasion resistance, compressions set, and swelling values. The tensile strength, tear resistance, and abrasion resistance of the gum vulcanizates of the blend were improved by the compatibilizing action of CR up to 5 parts per hundred parts of rubber (phr). In the case of the filled vulcanizates, the tear resistance, 300% modulus, hardness, and abrasion resistance increased with increasing dosage of nano calcium silicate. The elongation at break percentage decreased as expected when there was an increase in the modulus. Scanning electron microscopy was used to study the phase morphology of the blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

氯醚橡胶/丁腈橡胶共混物的结构与性能

研究了不同并用比的氯醚橡胶（ECO）／丁腈橡胶（NBR）共混物的相态结构,力学性能,耐老化性能和耐油性能,透射电镜照片显示：ECO／NBR为70／30（质量份,下同）时共混物呈双连续相：为60／40和40／60时ECO都为分散相,且两相界面清晰。加入NBR降低了ECO的拉伸强度和看断伸长率,以及耐热空气老化性能,随着NBR用量的提高,共混物硫化胶在油中的体积变化率增加,ECO／NBR为70／30时硫化胶在100℃热油中的性能保持率最高,而且体积变化率与ECO的相当。