An innovative material based on natural rubber and leather tannery waste to be applied as antistatic flooring

In recent decades, the production chain of beef and bovine leather has grown significantly because of an increase in the world's population and improved access to consumption. However, the generation of waste derived from this sector has grown simultaneously, and consequently, improved ways of adding value, reusing, and disposing these waste materials are being sought. In this article, we present a new and innovative composite material based on vulcanized natural rubber (NR), carbon black (CB), and leather waste (NR/CB/leather). The NR/CB/leather composites were prepared by thermal compression with 60 phr of CB and 60 or 80 phr of leather waste. In accordance with Brazilian sanitary laws, we exposed these composites for 24 h to bleach (B) and a disinfectant with the aim of simulating a true everyday cleaning use. The deconvolution of the impedance semicircles was carried out, and two relaxation phenomena around linear relaxation frequencies of about 10⁵ and 10⁶ Hz were found and associated mainly with charge carriers from CB and leather waste. With the addition of leather, the electrical conductivity of the composites increased two orders of magnitude from 5.70 × 10^?6 for the NR/CB to 7.97 × 10^?4 S/cm for NR/CB/leather‐60 phr B. These results point to the possibility of using these composites as an antistatic flooring once they exhibit acceptable values of electrical conductivity and once they withstand, from the structural, morphological, and electrical point of view, exposure to sanitizing agents. Furthermore, the production of these composites will add value to and enable an environmentally acceptable disposal of leather waste. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41297.     

Electrical conductivity of carbon black/single-wall carbon nanotube/low-density polyethylene ternary composite foam

In order to obtain high electrical conductive low-density polyethylene (LDPE) foam, carbon black (CB), single-wall carbon nanotube (SWCNT), and LDPE (CB/SWCNT/LDPE) ternary composite foams were successfully fabricated by chemical compression molding method. The electrical conductivity, mechanical properties, microstructure, density, and crystallinity of the foam were studied in detail. It can be found that CB and SWCNT have synergistic effect. For the CB/SWCNT/LDPE composite foam which containing 19 wt % CB and 0.05 wt % SWCNT, its density is only 0.082 g cm⁻¹ and the electrical conductivity can reach at 2.88 × 10⁻⁵ S cm⁻³, which is far more than 15 orders of magnitudes of pure polyethylene and 4 orders of magnitudes times higher than sample which CB content is 19 wt %. It is noteworthy that ultralow concentration of SWCNT could drastically improve the electrical conductivity and reduce the density of LDPE foams. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48382.     

Electrical conductivity and mechanical properties of polyaniline/natural rubber composite fibers

Electrically conducting elastomer fibers based on natural rubber (NR) and up to 10% w/w polyaniline (PANI) in its emeraldine base (EB) form were fabricated by a wet spinning process. The resulting fibers at various PANI contents were doped by immersion in aqueous HCl solution, which converted the PANI to the electrically conductive emeraldine salt (ES) form. The morphology of the composite fibers was studied by scanning electron microscopy (SEM). PANI particles were inhomogeneously distributed in the NR matrix. The electrical conductivity of the fibers increased with the increasing PANI‐ES content and leveled off at a value of around 10^?3 S/cm at PANI‐ES concentration of 5% w/w. The fibers retained most of their elasticity upon doping, while the tenacity was somewhat reduced. Gratifyingly, the electrical conductivity of the new elastomer fibers was preserved upon elongational deformation, even if strains as large as 600% were applied. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Stability of electrical properties of carbon black‐filled rubbers

Conducting composites were prepared by melt mixing of ethylene–propylene–diene terpolymer (EPDM) or styrene‐butadiene rubber (SBR) and 35 wt % of carbon black (CB). Stability of electrical properties of rubber/CB composites during cyclic thermal treatment was examined and electrical conductivity was measured in situ. Significant increase of the conductivity was observed already after the first heating–cooling cycle to 85°C for both composites. The increase of conductivity of EPDM/35% CB and SBR/35% CB composites continued when cyclic heating‐cooling was extended to 105°C and 125°C. This effect can be explained by reorganization of conducting paths during the thermal treatment to the more conducting network. EPDM/35% CB and SBR/35% CB composites exhibited very good stability of electrical conductivity during storage at ambient conditions. The electrical conductivity of fresh prepared EPDM/35% CB composite was 1.7 × 10⁻² S cm⁻¹, and slightly lower conductivity value 1.1 × 10⁻² S cm⁻¹ was measured for SBR/35% CB. The values did not significantly change after three years storage. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Electrical conductivity of epoxy/silicone/carbon black composites: Effect of composite microstructure

The objective of this work is to study the effect of electrical conductivity and physical‐mechanical properties of carbon black (CB) filled polymer composites. This goal is achieved by synthesizing epoxy/silicon phase separated blend structure of composites filled with CB. The percolation threshold of epoxy/silicone/CB composites decreased and the total conductivity increased compared to the pure epoxy/CB composite. A threefold increase was obtained with tensile strength of epoxy/silicone/CB composite with 25 wt% of silicone and 5 wt% of CB in comparison with epoxy/CB systems. This composite has conductivity of about 10⁻⁶ S/cm, which is six orders of magnitude higher than for epoxy/CB composites at the same concentration of CB. POLYM. COMPOS., 35:2234–2240, 2014. © 2014 Society of Plastics Engineers     

Cation‐exchange kinetics and electrical conductivity studies of an ‘organic‐inorganic’ composite cation‐exchanger: Polypyrrole Th(IV) phosphate

Polypyrrole Th(IV) phosphate, an electrically conducting ‘organic‐inorganic’ cation‐exchange composite material was prepared by the incorporation of an electrically conducting polymer, i.e., polypyrrole, into the matrix of a fibrous type inorganic cation‐exchanger thorium(IV) phosphate. The composite cation‐exchanger has been of interest because of its good ion‐exchange capacity, higher chemical and thermal stability, and high selectivity for heavy metal ions. The temperature dependence of electrical conductivity of this composite system with increasing temperatures was measured on compressed pellets by using four‐in‐line‐probe dc electrical conductivity measuring instrument. The conductivity values lie in the semiconducting region, i.e., in the order of 10^?6 to 10^?4 S cm^?1 that follow the Arrhenius equation. Nernst–Plank equation has been applied to determine some kinetic parameters such as self‐diffusion coefficient (D₀), energy of activation (E_a), and entropy of activation (ΔS*) for Mg(II), Ca(II), Sr(II), Ba(II), Ni(II), Cu(II), Mn(II), and Zn(II) exchange with H⁺ at different temperatures on this composite material. These results are useful for predicting the ion‐exchange process occurring on the surface of this cation‐exchanger. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Optical transmittance and electrical conductivity of silica glass with biserial and hierarchical network structures made of carbon nanofibers

Silica glass composites, with biserial and hierarchical percolative network made of carbon nanofibers (CNFs), was fabricated using a layer-by-layer technique and spark plasma sintering to obtain high optical transmittance and electrical conductivity. Owing to the network, the critical volume fraction, V_c, for the CNF percolation in the silica glass-matrix composite (0.5–0.7 vol%), when the electrical conductivity of the composite drastically increased with change from insulator (～10^?10 S/m) to conductor (～10^?1 S/m), is smaller than theoretical V_c predicted for the three-dimensional random orientation of CNFs (2.6 vol% for the CNF aspect ratio of 30). The conductivity of the composite with above the V_c of CNFs (～10 S/m) is higher than that reported for the polymer-matrix composite (～10^?5–～10^?3 S/m). Furthermore, high optical transmittance was observed for the electrically conductive composite with V_c of CNFs.     

Preparation of polystyrene–graphite conducting nanocomposites via intercalation polymerization

In situ polymerization of styrene was conducted in the presence of expanded graphite obtained by rapid heating of a graphite intercalation compound (GIC), to form a polystyrene–expanded graphite conducting composite. The composite showed excellent electrically conducting properties even though the graphite content was much lower than in normal composites. The transition of the composite from an electrical insulator to an electrical semiconductor occurred when the graphite content was 1.8 wt%, which is much lower than that of conventional conducting polymer composites. TEM, SEM and other studies suggest that the graphite was dispersed in the form of nanosheets in a polymer matrix with a thickness of 10–30 nm, without modification of the space between carbon layers and the structure of the graphite crystallites. The composite exhibited high electrical conductivity of 10^?2 S cm^?1 when the graphite content was 2.8–3.0 wt%. This great improvement of conductivity could be attributed to the high aspect ratio (width‐to‐thickness) of the graphite nanosheets. The rolling process strongly affected the conductivity and the mechanical properties of the composite. © 2001 Society of Chemical Industry     

Fabrication of electrically conductive polymer composites for bipolar plate by two‐step compression molding technique

Electrically conductive polymer composites for bipolar plate were fabricated by two‐step compression molding technique. Raw materials consisted of natural graphite flakes (G), expanded graphite (EG), carbon black (CB), and phenol resin (PF). The G/EG/CB/PF composites were first compressed at a temperature lower than curing point (100°C) and then cured at a high temperature above curing point (150°C) and high pressure (10 MPa). Results showed that G and EG are oriented in the direction parallel to the composite plate surface. CB is dispersed not only in the phenol resin matrix but also in the packing and porous space of G and EG. The addition of EG and CB significantly increases number of the electrical channels and thus enhances the electrical conductivity of the composite. Under optimal conditions, electrical conductivity and flexural strength of the composite were 2.80 × 10⁴ S/m and 55 MPa, respectively, suggesting that the dipolar plates prepared by two‐step compression molding technique are adequate to meet the requirement of proton exchange membrane fuel cells. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2296–2302, 2013     

Dependence of the electrical conductivity and elastomeric properties on sample preparation of blends of polyaniline and natural rubber

Blend films (free‐standing) containing 20% in volume of polyaniline (PANI) in 80% of natural rubber (NR) were fabricated by casting in three different ways: (1) adding PANI‐EB (emeraldine base) dissolved in N‐methyl‐2‐pyrrolidone (NMP) to the latex (NRL), (2) adding PANI‐EB dissolved in m‐cresol to NR dissolved in xylol (NRD), (3) overlaying the surface of a pure NR cast film with a PANI layer grown by in situ polymerization (NRO). All the films were immersed into HCl solution to achieve the primary doping (protonation) of PANI before the characterization. The main goal here was to investigate the elastomeric and electrical conductivity properties for each blend, which may be applied as pressure and deformation sensors in the future. The characterization was carried out by optical microscopy, dc conductivity, vibrational spectroscopy (infrared absorption and Raman scattering), thermogravimetry analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), and tensile stress–strain curves. The results suggest that the NRL blend is the most suitable in terms of mechanical and electrical properties required for applications in pressure and deformation sensors: a gain of conductivity without losing the elastomeric property of the rubber. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1498–1503, 2005     

Flexible and stretchable electrode based on multiwalled carbon nanotube/deproteinized natural rubber composites

One of stretchable electronic devices is known as the compliant electrode which can retain good electrical conductivity under deformation. Compliant electrodes from MWCNTs and DPNR were prepared by using a UV‐curing process and Triton X‐100 as a dispersing agent. The effect of Triton X‐100/MWCNTs volume ratio was investigated by transmission electron microscopy indicating the highest dispersion was obtained at the volume ratio of 15.6. The mechanical and electrical properties were investigated by a melt rheometer in a tension mode. The 3%v/v MWCNTs composite possessed an excellent mechanical behavior (Young's modulus = 1.27 × 10⁶ Pa) and a high electrical conductivity (1.03 S/cm) relative to previous works. Under the same experimental conditions, a commercial compliant electrode named Danfoss exhibited the Young's modulus and electrical conducivity values of 7.56 × 10⁶ Pa and 2.54 × 10^?2 S/cm, respectively, which were inferior to the 3%v/v MWCNTs/DPNR. Moreover, the composite film still retained good electrical behaviors under 100% strain, high extentional strain rate of 1 s^?1, high flexed angle, and repeated stretching cycles (40% strain, 50 times) due to the intimate compatibility between the MWCNTs and the elastomer matrix. POLYM. ENG. SCI., 57:1356–1366, 2017. © 2017 Society of Plastics Engineers     

Electrical and thermal conductivity and tensile and flexural properties: Comparison of carbon black/polycarbonate and carbon nanotube/polycarbonate resins

Adding conductive carbon fillers to thermoplastic polymers increases the resulting composite's electrical conductivity. Carbon black (CB) is very effective at increasing composite electrical conductivity at low loading levels. In this study, varying amounts (2 to 10 wt %) CB were added to polycarbonate (PC) and the resulting composites were tested for electrical conductivity (1/electrical resistivity), thermal conductivity, and tensile and flexural properties. These results were compared with prior work done for carbon nanotubes (CNT) in polycarbonate. The percolation threshold was ～ 2.3 vol % CB compared to between 0.7 and 1.4 vol % CNT. At 8 wt % filler, the CNT/PC composite had an electrical resistivity of 8 ohm‐cm compared to 122 ohm‐cm for the CB/PC composite. The addition of CB to polycarbonate increased the composite electrical and thermal conductivity and tensile and flexural modulus. The 8 wt % (5.5 vol %) CB in polycarbonate composite had a good combination of properties for semiconductive applications. Ductile tensile behavior is noted in pure polycarbonate and in samples containing up to 8 wt % CB. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and studies of the physical properties of polyaniline and polyurethane‐modified epoxy composites

Two series of toughened, semiconductive polyaniline (PANI)/polyurethane (PU)‐epoxy (PANI/PU‐EPOXY) nano‐composites were prepared using a conductive polymer, PANI, and PU prepolymer‐modified‐diglycidyl ether of bisphenol A (DGEBA) epoxy. First, the PU prepolymer‐modified epoxy oligomer was synthesized by a stoichiometric reaction between the terminal isocyanate groups of the PU prepolymer and the pendent hydroxyl groups of the epoxide. PU prepolymers were made either of polyester (polybutylene adipate, PBA) or polyether (polypropylene glycol, PPG) segments. The composites were characterized by thermal, morphological, mechanical, and electrical studies. Impact strength was enhanced 100% in PU (PPG 2000)‐modified composites; whereas, only ca. 30–50% increases in impact strength were observed for the other modified composites. In addition, the thermal stability of this composite proved superior to that of neat epoxy resin, regardless of a PU content at 27.5 wt%. Scanning electron microscopy (SEM) morphology study showed that the spherical PU (PPG 2000) particles (ca. 0.2–0.5 μm) dispersed within the matrix accounts for these extraordinary properties. The conductivity of the composite increased to ca. 10^?9–10^?3 S cm^?1 upon addition of PANI when tested in the frequency range 1 kHz–13 MHz. This study demonstrated a useful way to simultaneously improve the toughness and conductivity of the epoxy composite, thus rendering it suitable for electromagnetic interference and various charge dissipation applications. POLYM. ENG. SCI., 2008. © 2007 Society of Plastics Engineers     

Sustainable conducting polymer composites: study of mechanical and tribological properties of natural fiber reinforced PVA composites with carbon nanofillers

ABSTRACT

Ball milled jute fiber (JF) was added to Polyvinyl Alcohol (PVA)/20 wt.% multi-layer graphene (MLG) composites in various proportions (0, 5, 10, 15 and 20 wt.%) to prepare sustainable and biodegradable conducting polymer composites. Also, PVA/17.5wt.%MLG/2.5wt.%MWCNT/20wt.% JF composite was prepared for comparison purpose. A dynamic mechanical analysis of the composites was conducted to analyze their viscoelastic nature. The electrical conductivity of the composites was measured to study their suitability for various applications. Jute reinforcement increased the electrical conductivity of PVA/MLG nanocomposites. The PVA/20wt.%JF/17.5wt.%MLG/2.5wt.%MWCNT hybrid composite had the highest electrical conductivity of 3.64 × 10^?4 S/cm among all the composites prepared. Multilayered structures of the hybrid composite films were made by hot-pressing, and their effectiveness in electromagnetic interference shielding was tested. The shielding effectiveness of the composites decreased with jute addition. The wear resistance of PVA/MLG/JF composites increased with an increase in the jute content up to an optimum value of 10 wt.%, and then it started deteriorating.     

Effects of hybrid fillers on the electrical conductivity,EMI shielding effectiveness,and flame retardancy of PBT and PolyASA composites with carbon fiber and MWCNT

The effects of hybrid fillers of carbon fiber (CF) and multiwall carbon nanotube (MWCNT) on the electrical conductivity, electromagnetic interference shielding effectiveness (EMI SE), flame retardancy, and mechanical properties of poly(butylene terephthalate) (PBT)/poly(acrylonitrile-co-styrene-co-acrylate) (PolyASA) (70/30, wt %) with conductive filler composites were investigated. The CF was used as the main filler, and MWCNT was used as the secondary filler to investigate the hybrid filler effect. For the PBT/PolyASA/CF (8 vol %)/MWCNT (2 vol %) composite, a higher electrical conductivity (1.4 × 10⁰ S cm⁻¹) and EMI SE (33.7 dB) were observed than that of the composite prepared with the single filler of CF (10 vol %), which were 9.0 × 10⁻² S cm⁻¹ and 23.7 dB, respectively. This increase in the electrical properties might be due to the longer CF length and hybrid filler effect in the composites. From the results of aging test at 85 °C, 120 h, the electrical conductivity and EMI SE of the composites decreased slightly compared to that of the composite without aging. The results of electrical conductivity, EMI SE, and flame retardancy suggested that the composite with the hybrid fillers of CF and MWCNT showed a synergetic effect in the PBT/PolyASA/CF (8 vol %)/MWCNT (2 vol %) composite. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48162.     

Dynamic Mechanical,DSC, and Electrical Investigations on Nano Al2O3 Filled PVA:NH4SCN:DMSO Polymer Composite Dried Gel Electrolytes

This paper reports the dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and ionic conductivity studies on nanosized Al₂O₃(aluminium oxide) filled PVA:NH₄SCN:DMSO polymer composite dried gel electrolytes prepared by the wet chemistry route. Better mechanical stability and thermal behavior are noticed in the composite system. Multiple relaxation peaks seen in tangent loss measurements (in DMA studies) have been suitably correlated. Enhancement in ionic conductivity has been noticed with an optimum value of 4.02 × 10^?3 Scm^?1 for 4 wt% nano Al₂O₃ filled composite electrolytes. Temperature dependence of ionic conductivity shows a combination of Arrhenius and VTF (Vogel-Tamman-Fulcher) behavior.     

Novel electrically conductive and ferromagnetic composites of poly(aniline‐co‐aminonaphthalenesulfonic acid) with iron oxide nanoparticles: Synthesis and characterization

Nanocomposites of iron oxide (Fe₃O₄) with a sulfonated polyaniline, poly(aniline‐co‐aminonaphthalenesulfonic acid) [SPAN(ANSA)], were synthesized through chemical oxidative copolymerization of aniline and 5‐amino‐2‐naphthalenesulfonic acid/1‐amino‐5‐naphthalenesulfonic acid in the presence of Fe₃O₄ nanoparticles. The nanocomposites [Fe₃O₄/SPAN(ANSA)‐NCs] were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, elemental analysis, UV–visible spectroscopy, thermogravimetric analysis (TGA), superconductor quantum interference device (SQUID), and electrical conductivity measurements. The TEM images reveal that nanocrystalline Fe₃O₄ particles were homogeneously incorporated within the polymer matrix with the sizes in the range of 10–15 nm. XRD pattern reveals that pure Fe₃O₄ particles are having spinel structure, and nanocomposites are more crystalline in comparison to pristine polymers. Differential thermogravimetric (DTG) curves obtained through TGA informs that polymer chains in the composites have better thermal stability than that of the pristine copolymers. FTIR spectra provide information on the structure of the composites. The conductivity of the nanocomposites (～ 0.5 S cm^?1) is higher than that of pristine PANI (～ 10^?3 S cm^?1). The charge transport behavior of the composites is explained through temperature difference of conductivity. The temperature dependence of conductivity fits with the quasi‐1D variable range hopping (quasi‐1D VRH) model. SQUID analysis reveals that the composites show ferromagnetic behavior at room temperature. The maximum saturation magnetization of the composite is 9.7 emu g^?1. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Electrical,rheological, and mechanical properties copolymer/carbon black composites

This work aims to evaluate the electrical conductivity and the rheological and mechanical properties of copolymer/carbon black (CB) conductive polymer composites (CPCs). The copolymers, containing ethylene groups in their structure, used as matrix were polyethylene grafted with maleic anhydride (PEgMA), ethylene-methyl acrylate–glycidyl methacrylate (EMA-GMA), and ethylene-vinyl acetate (EVA). For comparison purposes, bio-based polyethylene (BioPE)/CB composites were also studied. The electrical conductivity results showed that the electrical percolation threshold of BioPE/CB composite was 0.36 volume fraction of CB, whereas the rheological percolation threshold was 0.25 volume fraction of CB. The most conductive CPC was BioPE/CB. Among the copolymer/CB CPCs, PEgMA/CB showed the highest conductivity, which can be attributed to the fact that the PEgMA copolymer had higher crystallinity. It also has a higher amount of ethylene groups in its structure. Torque rheometry analysis indicated that EMA-GMA copolymer may have reacted with CB. Rheological measurements under oscillatory shear flow indicated the formation of a percolated network in BioPE/CB and copolymer/CB composites. Morphology analysis by scanning electron microscopy (SEM) indicated the formation of a percolated network structure in BioPE/CB composite and finely dispersed CB particles within the PEgMA copolymer. Wetting of CB particles/agglomerates by the copolymer matrix was observed in EVA/CB and EMA-GMA/CB composites. Conductive CB acted as reinforcing filler as it increased the elastic modulus and tensile strength of BioPE and the copolymers.     

A conducting composite based on poly(N‐vinylcarbazole)–formalin resin and acetylene black

A poly(N‐vinylcarbazole) (PNVC)–formalin (FO) resin (PNVC‐FO) was prepared via copolycondensation between N‐vinylcarbazole (NVC) and FO in the presence of dry HCl gas in toluene medium at 110°C. A highly conducting composite of PNVC‐FO resin with nanodimensional acetylene black (AB) was prepared by carrying out the polycondensation reaction in presence of a suspension of acetylene black (AB) in toluene. The inclusion of PNVC in the PNVC‐FO‐AB composite was confirmed by FT‐IR analysis. Scanning electron microscopic analyses of PNVC‐FO resin and PNVC‐FO‐AB composite revealed formation of spherical particles and aggregates of irregular shapes respectively. Thermogravimetric analyses revealed the overall stability order as: AB > PNVC‐FO‐AB composite > PNVC‐FO resin > PNVC homopolymer. In sharp contrast to PNVC and PNVC‐FO resin, which were both nonconducting (10^?12 to 10^?16 S/cm), the conductivity of the composites reached values between 0.75 S/cm and 6.54 S/cm corresponding to AB loading of 28–49 wt % respectively. Temperature versus conductivity studies revealed an initial increase in conductivity upto 200°C and current–voltage characteristics of the PNVC‐FO‐AB composite showed a linear trend consistent with Ohmic behavior. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3837–3843, 2007     

Development and Characterisation of Electrically Conductive Polymeric‐Based Blends for Proton Exchange Membrane Fuel Cell Bipolar Plates

The main objective of this work was to develop films with controlled dimensions for proton exchange membrane fuel cell (PEMFC) bipolar plates (BPPs) using the twin‐screw extrusion process. These films consisted of a low‐viscosity polyethylene terephthalate (PET) in which a mixture of high specific surface area carbon black (CB) and synthetic flake graphite (GR) were dispersed. A third conductive additive, consisting of silver‐coated glass particles (SCG) or multi‐walled carbon nanotubes (MWCNT), was also added at a low concentration (5 wt.‐%) in order to study its synergistic effect on the PET‐based blend electrical conductivity. As the developed blends had to meet properties suitable for PEMFC bipolar plate applications, they were characterised for their electrical through‐plane resistivity, mechanical properties and oxygen permeability. Through‐plane electrical resistivity of about 0.3 Ω·cm and oxygen permeation rate of 3.5 × 10^–8 cc cm^–2 s^–1 were obtained for only 30 wt.‐% of a 60:40 mixture of CB/GR conductive additives. Although the substitution of 5 wt.‐% of CB/GR by the same amount of MWCNT had no significant effect on BPPs' electrical resistivity, it helped to improve their mechanical properties and especially their oxygen permeation, which was decreased from 3.5 × 10^–8 cc cm^–2 s^–1 to around 0.6 × 10^–8 cc cm^–2 s^–1.