Influence of Zn injection on characteristics of oxide film on 304 stainless steel in borated and lithiated high temperature water

The oxide film on 304 stainless steel exposed to the hydrothermal environments at 573.15 K up to 20 days without/with 10 ppb Zn injection has been investigated ex situ by X-ray photoelectron spectroscopy (XPS). ZnFe₂O₄ and ZnCr₂O₄ were found to be formed in the oxide film at the initial stage of immersion by substitution reaction between Zn²⁺ and Fe²⁺, and ZnCr₂O₄ became dominant after long-term immersion. The calculations of potential-pH diagrams, solubilities and crystallographic features of spinels have been done to evaluate the oxide film structure and the inhibition mechanism caused by Zn injection.     

The oxidation behavior and mechanical properties of MoSi2–CrSi2–SiC–Si coated carbon/carbon composites in high-temperature oxidizing atmosphere

A MoSi₂–CrSi₂–SiC–Si multi-component coating was prepared on the surface of carbon/carbon (C/C) composites by a two-step pack cementation method. The microstructure, oxidation behavior and mechanical properties of the coating were studied. These results show that the multi-component coating could protect the C/C composites from oxidation in air at 1873 K for 300 h and withstand 30 thermal cycles between 1873 K and room temperature, respectively. The mass loss and mechanical property loss of the coated C/C composites are considered due to the worse fluidity of SiO₂ at intermediate temperatures and the thermal mismatch between the coating and C/C composites.     

Oxidation behaviour of Ti–Al–C films composed mainly of a Ti2AlC phase

This paper addresses the oxidation behaviour of Ti–Al–C films composed mainly of a Ti₂AlC phase. The films exhibited rather low oxidation rates at 600 and 700 °C, with an oxygen-rich zone or a thin oxide layer appearing on the film surfaces. Much faster oxidation rates were observed at 800 and 900 °C. The Ti₂AlC phase was quickly consumed by oxidation. From the film surface to the inner zone, TiO₂-rich layer, Al₂O₃-rich layer, and TiO₂ + Al₂O₃ mixed layer was observed, respectively. The oxidation mechanism of the Ti–Al–C film is discussed based on the experimental results.     

The corrosion behaviour of Zr-based bulk metallic glasses in 0.5 M NaCl solution

The corrosion behaviour of eutectic Zr₅₀Cu₄₀Al₁₀ and hypoeutectic Zr₇₀Cu₆Al₈Ni₁₆ bulk metallic glasses (BMGs) was studied by electrochemical measurements, scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray photoelectron spectroscopy (XPS). Zr₅₀Cu₄₀Al₁₀ BMG was highly susceptible to pitting corrosion in naturally aerated 0.5 M NaCl solution at 30 °C. In contrast, Zr₇₀Cu₆Al₈Ni₁₆ BMG passivated spontaneously under the same condition. EDX results for Zr₅₀Cu₄₀Al₁₀ indicated that enrichment of Cu, Cl and O occurred in the pitted region, while for Zr₇₀Cu₆Al₈Ni₁₆ BMG, no significant difference was found in the surface composition from the specimens before and after immersion in the solution. XPS analysis including angle-resolved measurements for Zr₇₀Cu₆Al₈Ni₁₆ BMG revealed that zirconium cation (Zr⁴⁺) was highly concentrated in both air-formed and passive films. Furthermore, the concentration of Zr⁴⁺ ions after immersion for 24 h or more showed tendency to increase with decreasing take-off angle, indicating that the exterior part of the passive film consisted exclusively of zirconium oxyhydroxide. The high corrosion resistance of Zr₇₀Cu₆Al₈Ni₁₆ BMG was attributed to the formation of homogeneous and stable passive film enriched with zirconium.     

Porous anodic oxides on titanium and on a Ti-W alloy

The growth of a nanoporous anodic oxide on titanium and a Ti-20 at.% W alloy, both deposited by magnetron sputtering, in a glycerol/phosphate electrolyte at 453 K is reported. The oxide formed on titanium is a mixture of amorphous titania and anatase. However, that on the alloy is amorphous only and forms at increased efficiency, about 27%. The amorphous structure is considered to be stabilized by incorporated units of WO₃, which are distributed uniformly throughout the anodic film. The growth of the porous oxides is suggested to be associated with loss of film species at the film/electrolyte interface at the base of pores, with new oxide forming exclusively at the metal/film interface by inward migration of O²⁻ ions.     

Surface characterization of oxides grown on the Ti–13Nb–13Zr alloy and their corrosion protection

Oxide films were formed on the biocompatible alloy Ti–13Nb–13Zr in a phosphate buffer at open-circuit potential (E_oc), potentiodynamically up to 8 V, or by micro-arc oxidation (MAO) at 300 V. Their electrochemical properties were assessed in a phosphate buffer saline solution (PBS). EIS and SEM results showed that the E_oc and potentiodynamically formed oxide films were compact and behave as a monolayer, while the MAO oxide was a bilayered film (compact inner and porous outer layers). Open-circuit potential and EIS resistance values indicated that the MAO oxide provides the best corrosion protection for the alloy in PBS.     

Characterisation of oxide films formed on Co–29Cr–6Mo alloy used in die-casting moulds for aluminium

Oxide films formed at 700 °C on Co–29Cr–6Mo alloy were characterised extensively to improve the corrosion resistance of the alloy to liquid Al, enabling its use in Al die-casting moulds. Film of duplex layer consisting of an outer CoO-rich layer and an inner Cr₂O₃-rich layer was observed in samples subjected to oxidation for 4 h. With an increase in duration of oxidation, CoO was gradually replaced by Cr₂O₃, resulting in a single-layered oxide film dominantly composed of Cr₂O₃. The oxide film evolved with duration of oxidation treatment indicating the possibility of optimising films for Al die-casting moulds.     

Effects of electrolyte pH and temperature on dielectric properties of anodic oxide films formed on niobium

The effects of electrolyte pH and temperature on the structure and properties of anodic oxide films formed on niobium in phosphoric acid solution with the addition of NH₄OH for pH adjustment have been investigated. The film thickness formed at the same voltage slightly increased with increasing pH and significantly increased with increasing electrolyte temperature. The capacitance of the film was independent of electrolyte pH in an acid region, while it notably increased with increasing pH in an alkaline region. The relative permittivity of the film changed 43.7-80.5 when the electrolyte pH was increased from 1.6 to 10. The incorporation depth and content of phosphorus in the film were markedly suppressed at pH 10, and nitrogen was found to penetrate into a depth of 70%. Furthermore, the apparent transport number of Nb⁵⁺ ion decreased from 0.26 to 0.02 by a pH increase from 1.6 to 10. The notable changes in structure and dielectric properties of the anodic niobia film formed in the alkaline region would primarily be caused by the different incorporation behavior of electrolyte species such as phosphorous and nitrogen.     

In-situ synthesis and mechanical properties of Zr-based bulk metallic glass matrix composites manipulated by nitrogen additions

Our study investigates in-situ synthesis and mechanical properties of Zr-based bulk metallic glass (BMG) matrix composites via arc plasma-induced accelerated displacement reaction (APADR) process. The aluminum nitride precursor under arc plasma-induced ultra-high temperature results in higher contents of dissolved nitrogen as well as precipitation of zirconium nitride (ZrN) particles in a Zr-based amorphous matrix. The nitrogen in the matrix results in a decrease of crystallization resistance (lower T_x and reduced glass-forming ability), but an increase of mechanical stability (a decrease of strain burst sizes). In particular, in-situ formed ZrN, which exhibits a homogeneous distribution and strong interfacial bonding with the matrix, causes an increase in compressive fracture strength and significant plastic deformation in the composite compared with the monolithic BMG. The formation of multiple shear bands and the enhancement of shear band interactions by the dissolved nitrogen as well as the in-situ formed ZrN particles were carefully confirmed by a statistical analysis on serrated flows. These results give us a guideline on how to manipulate nitrogen contents and fabricate in-situ BMG matrix composites with improved mechanical properties via APADR process.     

Environmental factors affecting the corrosion behaviour of reinforcing steel: I. The early stage of passive film formation in Ca(OH)2 solutions

Oxide film thickening on reinforcement steel at early stage of formation is followed in naturally aerated Ca(OH)₂ solutions, recalling the natural behaviour in concrete, by measuring the open-circuit potential, E, with time up to 4 h. The final potentials, E_fin, are reached from negative values indicating oxide film growth. E varies with the Ca(OH)₂ concentration according to a straight line relationship. Oxide film thickening, at early stage of immersion, follows a direct logarithmic growth law as evident from the linear relationship between E and log t. The rate of oxide film thickening deceases by increasing the concentration and pH of the solution and by raising the temperature. The free activation energy of oxide film thickening is determined and found to be 29.28 kJ/mole, indicating that the process of oxide film growth is under diffusion control.     

Oxidation behavior of molten magnesium in atmospheres containing SO2

The microchemistry and morphology of the oxide layer formed on molten magnesium in atmospheres containing SO₂ were examined. Based on the results and the thermodynamic and kinetic calculations of oxide-growth process, a schematic oxidation mechanism is presented. The results showed that the oxide scales with network structure were generally composed of MgO, MgS, and MgSO₄ with different layers, depending on the SO₂ content, the time and the temperature. The formation of MgSO₄ was important for the formation of the protective oxide scales. The growth of the oxide scales followed the parabolic law at 973 K and was controlled by diffusion.     

Preparation and oxidation resistance of a crack-free Al diffusion coating on Ti22Al26Nb

A crack-free Al diffusion coating has been developed to improve the oxidation resistance of Ti22Al26Nb. It was produced by a two-step method; an Al film was deposited on the substrate alloy by arc ion plating followed by a diffusion process conducted at 873 K in pure Ar to form the Al diffusion coating. The two-step method lowers the temperature required to form the diffusion coating, which dramatically decreases the thermal stress developed in the coating and results in it being crack-free. The oxidation resistance of the non-coated Ti22Al26Nb alloy in isothermal and cyclic tests in air at 1073 K was poor, but the coated specimens possessed excellent oxidation resistance because a protective α-Al₂O₃ scale formed. The life of the Al diffusion coating greatly depends upon the rapid initial formation of a protective Al₂O₃ scale and interdiffusion between coating and substrate. Once the stable Al₂O₃ scale has formed and the composition changes from (Ti, Nb)Al₃ into (Ti, Nb)Al₂, the coating has a long life.     

High temperature oxidation of Fe-Al and Fe-Cr-Al alloys: The role of Cr as a chemically active element

Good high-temperature corrosion resistance of Fe-Al alloys in oxidizing environments is due to the α-Al₂O₃ film which is formed on the surface provided temperature is above 900 °C and the Al-content of the alloy exceeds the critical value. Ab initio calculations combined with experiments on Fe-13Al, Fe-18Al, Fe-23Al and Fe-10Cr-10Al alloys show that the beneficial effect of Cr on the oxidation resistance is significantly related to bulk effects. The comparison of experimental and calculated results indicates a clear correlation between the Fe-Cr chemical potential difference and the formation of the protective oxide scales.     

Oxidation of single crystal PWA 1483 at 950 °C in flowing air

The oxidation behaviour of single crystal PWA 1483 at 950 °C was investigated by means of XRD, SEM and EDS. The parabolic oxidation behaviour, as defined by mass gain and the respective oxide layer thicknesses, is characterized by a parabolic rate constant of about 4 × 10⁻⁶ mg²/(cm⁴ × s) and the formation of a multi-layered oxide scale. An outer scale contains a Ti-bearing thin film composed of TiO₂ and NiTiO₃ but mostly Cr in Cr₂O₃ and (Ni/Co)Cr₂O₄ besides NiTaO₄. This outer scale is connected to a discontinuous layer of Al₂O₃ and an area of γ′-depletion within the base material.     

Electrochemical study on hot corrosion of Si-modified aluminide coated In-738LC in Na2SO4-20 wt.% NaCl melt at 750 °C

The corrosion performance of the slurry Si-modified aluminide coating on the nickel base superalloy In-738LC exposed to low temperature hot corrosion condition has been investigated in Na₂SO₄-20 wt.% NaCl melt at 750 °C by combined use of the anodic polarization and characterization techniques.The coated specimen showed a passive behavior up to −0.460 V vs. Ag/AgCl (0.1 mol fraction) reference electrode, followed by a rapid increase in anodic current due to localized attack in the higher potential region. In the passive region, the anodic dissolution of constituents of the coating occurred through the passive film, probably SiO₂, at slow rate of 20-30 μA/cm². The passive current for the Si-modified coating was two orders of magnitude smaller than that for bare In-738LC, which is known as Cr₂O₃ former in this melt. This indicates that the SiO₂ film is chemically more stable than Cr₂O₃ film under this condition. However, pitting-like corrosion commenced around −0.460 V and proceeded at the high rate of 100 mA/cm² in the higher potential region than +0.400 V. The corrosion products formed on the coating polarized in different anodic potentials were characterized by SEM, EDS and XRD. It was found from the characterization that oxidation was dominant attack mode and no considerable sulfidation occurred at 750 °C. The SiO₂ oxide was not characterized in the passive region because the thickness of the passive film was extremely thin, but was detected as the primary oxide in the localized corrosion region, where the selective oxidation of Al was observed by further progress of the corrosion attack front into the inner layer of coating.     

Ternary La–Al–C bulk metallic glasses

Glass formation, thermal stability, elastic moduli and mechanical properties of La–Al–C bulk metallic glasses (BMGs) were investigated. The BMGs of La_57.5Al_32.5C₁₀, La₆₀Al₃₀C₁₀, and La_62.5Al_27.5C₁₀ with the maximal diameters up to 3 mm can be synthesized. Compared with other La-based glassy systems, like La–Al–(Co, Ni, Cu), the La–Al–C BMGs with the similar La concentration exhibit higher glass transition temperatures (507–577 K) and elastic constants. The La–Al–C BMGs with the unusual T_g and elastic moduli fill a gap in thermal and elastic properties between light rare-earth-based BMGs and heavy rare-earth-based ones. The compressive yield strength of La_57.5Al_32.5C₁₀ BMG reaches to ∼1.1 GPa, higher than that of other reported La-based BMGs. The ternary BMGs with simple element constituent, high glass-forming ability and superior mechanical properties are significant for fundamental research as model materials.     

Corrosion behaviour of 16%Cr-4%Al and 16%Cr ODS ferritic steels under different metallurgical conditions in a supercritical water environment

The corrosion behaviour of 16%Cr and 16%Cr-4%Al ODS ferritic steels in different heat treatment conditions has been investigated in a supercritical water environment. The exposed coupons were analyzed using scanning electron microscopy (SEM), electron probe micro analysis (EPMA), Auger and X-ray diffraction analysis (XRD). It was found that the formation of oxides depends on the chemical composition and not on the metallurgical condition. The Al-free alloys formed a monolayer oxide film composed of (Cr, Fe)₂O₃. The Al-containing alloys formed an oxide film composed of an outer layer of hematite and magnetite and an inner layer of Al₂O₃. The oxidation mechanisms are discussed.     

The nature of the third-element effect in the oxidation of Fe-xCr-3 at.% Al alloys in 1 atm O2 at 1000 °C

The oxidation of an Fe-Al alloy containing 3 at.% Al and of four ternary Fe-Cr-Al alloys with the same Al content plus 2, 3, 5 or 10 at.% Cr has been studied in 1 atm O₂ at 1000 °C. Both Fe-3Al and Fe-2Cr-3Al formed external iron-rich scales associated with an internal oxidation of Al or of Cr+Al. The addition of 3 at.% Cr to Fe-3Al was able to stop the internal oxidation of Al only on a fraction of the alloy surface covered by scales containing mixtures of the oxides of the three alloy components, but not beneath the iron-rich oxide nodules which covered the remaining alloy surface. Fe-5Cr-3Al formed very irregular external scales where areas covered by a thin protective oxide layer alternated with others covered by thick scales containing mixtures of the oxides of the three alloy components, undergrown by a thin layer rich in Cr and Al, while internal oxidation was completely absent. Conversely, Fe-10Cr-3Al formed very thin, slowly-growing external Al₂O₃scales, providing an example of third-element effect (TEE). However, the TEE due to the Cr addition to Fe-3Al was not directly associated with a prevention of the internal oxidation of Al, but rather with the inhibition of the growth of external scales containing iron oxides. This behavior has been interpreted on the basis of a qualitative oxidation map for ternary Fe-Cr-Al alloys taking into account the existence of a complete solid solubility between Cr₂O₃ and Al₂O₃.     

The structure and high temperature corrosion performance of medium-thickness aluminide coatings on nickel-based superalloy GTD-111

Simple and Si-modified aluminide coatings having medium-thickness (40-60 μm) have been applied on the superalloy GTD-111 by a slurry technique. Hot corrosion and cyclic oxidation performance of the uncoated and the coated superalloy were investigated by exposing samples to a molten film of Na₂SO₄-40 %wt NaVO₃-10%wt NaCl at 780 °C and 1 h cyclic oxidation at 1100 °C in air, respectively. The presence of silicon in the aluminide structure increased the oxidation resistance by a factor of 1.7 times. In addition, a SiO₂-containing scale, which formed on the Si-containing coating surface, was stable during of the hot corrosion testing.     

Thermal stability under air of tungsten–titanium diffusion barrier layer between silica and platinum

The present work investigated the thermal stability of tungsten–titanium diffusion barrier layers intercalated between SiO₂ substrate and platinum thin film. The resulting structures were annealed under air in the temperature range 400–600 °C for annealing times up to 100 h. Chemical and structural characterizations at different stages of the treatment evidenced several phenomena occurring during annealing under air, especially the complete oxidation of the adhesive layer, the diffusion of tungsten oxide through platinum film at particle boundaries as well as the sublimation process of tungsten oxide. The results of film surface chemistry and microstructure were correlated with diffusion phenomena.