Synthesis and photoluminescence properties of the high-brightness Eu3+-doped Sr3Y(PO4)3 red phosphors

A series of red-emitting phosphors Eu³⁺-doped Sr₃Y(PO₄)₃ have been successfully synthesized by conventional solid-state reaction, and its photoluminescence properties have been investigated. The excitation spectra reveal strong excitation bands at 392 nm, which match well with the popular emissions from near-UV light-emitting diode chips. The emission spectra of Sr₃Y(PO₄)₃:Eu³⁺ phosphors exhibit peaks associated with the ⁵D₀ → ⁷F_J (J = 0, 1, 2, 3, 4) transitions of Eu³⁺ and have dominating emission peak at 612 nm under 392 nm excitation. The integral intensity of the emission spectra of Sr₃Y_0.94(PO₄)₃:0.06Eu³⁺ phosphors excited at 392 nm is about 3.4 times higher than that of Y₂O₃:Eu³⁺ commercial red phosphor. The Commission Internationale de l’Eclairage chromaticity coordinates, the quantum efficiencies and decay times of the phosphors excited under 392 nm are also investigated. The experimental results indicate that the Eu³⁺-doped Sr₃Y(PO₄)₃ phosphors are promising red-emitting phosphors pumped by near-UV light.     

Sr3GdLi(PO4)3F:Eu2+, Mn2+: A tunable blue-white color emitting phosphor via energy transfer for near-UV white LEDs

A series of Eu²⁺ and Mn²⁺ co-doping Sr₃GdLi(PO₄)₃F phosphors have been synthesized through high temperature solid state reaction. Eu²⁺ single doped Sr₃GdLi(PO₄)₃F phosphors have an efficient excitation in the range of 230–430 nm, which is in good agreement with the commercial near-ultraviolet (n-UV) LED chips, and gives intense blue emission centering at 445 nm. The critical distance of the Eu²⁺ ions in Sr₃GdLi(PO₄)₃F is computed and demonstrated that the concentration quenching mechanism of Eu²⁺ is mostly caused by the dipole-dipole interaction. By co-doping Eu²⁺ and Mn²⁺ ions in the Sr₃GdLi(PO₄)₃F host, the energy transfer from Eu²⁺ to Mn²⁺ that can be discovered. With the increase of Mn²⁺ content, emission color can be adjusted from blue to white under excitation of 380 nm, corresponding to chromatic coordinates change from (0.189, 0.108) to (0.319, 0.277). The energy transfer from Eu²⁺ to Mn²⁺ ions is proven to be a dipole-dipole mechanism on the basis of the experimental results and analysis of photoluminescence spectra and decay curves. This study infers that the obtained Sr₃GdLi(PO₄)₃F:Eu²⁺, Mn²⁺ phosphors may be a potential candidate for n-UV LEDs.     

Fluorescence properties with red-shift of Eu2+ emission in novel phosphor-silicate apatite Sr3LaNa(PO4)2SiO4 phosphors

A series of Eu²⁺-activated novel phosphor-silicate apatite Sr₃LaNa(PO₄)₂SiO₄ phosphors were synthesized by solid-state reaction. The X-ray diffraction (XRD) and Rietveld refinement, diffuse reflectance spectra, luminescent spectra, decay curves and thermal quenching properties were applied to characterize the obtained phosphors. The XRD result revealed that all the samples possessed only a single phase with hexagonal structure and the doping of Eu²⁺ ions were successfully incorporated into the crystal lattice. The reflectance spectra showed an obvious red-shift of the wavelength from 400 to 700 nm with increasing Eu²⁺ ion concentration. The three different crystallographic sites of Eu²⁺ ions had been confirmed by their lifetimes. All the samples exhibited broad absorption bands from 200 to 450 nm, revealing the phosphor-silicate phosphor interesting for application in the near-UV used phosphor-converted LED chips. These results suggested that the Eu²⁺-activated phosphor-silicate Sr₃LaNa(PO₄)₂SiO₄ phosphors have the potential for near-UV pumped white-light-emitting diodes (w-LEDs).     

A novel pure red phosphor Ca8MgLu(PO4)7:Eu3+ for near ultraviolet white light-emitting diodes

A novel red-emitting phosphor Ca₈MgLu(PO₄)₇:Eu³⁺ was synthesized by a high-temperature solid-state reaction method. Its crystal structure, photoluminescence emission and excitation spectra, and decay time were investigated in detail. X-ray diffraction (XRD) results indicate that Ca₈MgLu(PO₄)₇ crystallizes in single-phase component with a whitlockite-like structure and the space group R3c of β-Ca₃(PO₄)₂. The emission spectrum shows a dominant peak at 612 nm due to the dipole ⁵D₀→⁷F₂ transition of Eu³⁺, and the luminescence intensity keeps increasing with increasing the content of Eu³⁺ to 100%. The excitation spectrum is coupled well with the emission of near ultraviolet (NUV) LED (380–410 nm). The CIE coordinates of Ca₈MgLu(PO₄)₇:Eu³⁺ phosphor is (0.654, 0.346), being close to the standard value of National Television Standard Committee (NTSC) for red phosphor, (0.670, 0.330). The internal quantum efficiency of the phosphor is 69% under the excitation of 394 nm. The results show that Ca₈MgLu(PO₄)₇:Eu³⁺ is a very appropriate red-emitting phosphor with a high ratio of red and orange for NUV-based white LEDs.     

Tunable single-phase white-light-emitting Ba2Mg(BO3)2:Ce3+, Na+, Tb3+, Eu2+ phosphor based on energy transfer

A series of white-light-emitting phosphors of single-phase Ba₂Mg(BO₃)₂:Ce³⁺, Na⁺, Tb³⁺, Eu²⁺ were synthesized by conventional solid-state reaction. The crystal structure of the host was characterized by X-ray diffraction and investigated by Rietveld refinement. Photoluminescence properties were studied in detail. The energy transfer from Ce³⁺ to Tb³⁺ in Ba₂Mg(BO₃)₂ host was investigated and demonstrated to be a resonant type via a quadrupole–quadrupole mechanism. White light with wavelength tunable was realized by coupling the emission bands peaking at 417, 543 and 626 nm attributed to Ce³⁺, Tb³⁺ and Eu²⁺, respectively. By properly tuning the relative composition of Ce³⁺(Na⁺)/Tb³⁺/Eu²⁺, optimized Commission Internationale de l׳Eclairage (CIE) chromaticity coordinates (0.363, 0.295), high color rendering index (CRI) 90 and low correlated color temperature (CCT) 3793 K were obtained from the phosphor of Ba_1.90Ce_0.04Na_0.04Eu_0.02Mg_0.94Tb_0.06(BO₃)₂ upon the excitation of 296 nm UV radiation. These results indicate that Ba₂Mg(BO₃)₂:Ce³⁺, Na⁺, Tb³⁺, Eu²⁺ phosphor has a potential application as an UV radiation down-converting phosphor in white-light-emitting diodes.     

Red,green and blue-violet emission coexistence in white-light-emitting Ca3SiO4Cl2:Bi3+, Li+, Eu2+, Eu3+ phosphor

A series of emission-tunable Ca₃SiO₄Cl₂:Bi³⁺, Li⁺, Euⁿ⁺(n =2, 3) (CSC:Bi³⁺, Li⁺, Euⁿ⁺) phosphors have been synthesized via sol-gel method. The X-ray diffraction results indicate that the as-synthesized phosphors crystallize in a low temperature phase with the space group of P21/c. Energy transfer from Bi³⁺ to Eu³⁺/Eu²⁺ exists in CSC:Bi³⁺, Li⁺, Euⁿ⁺ phosphors. Under the excitation of 327 or 365 nm, the Ca_2.98−ySiO₄Cl₂:0.01Bi³⁺, 0.01Li⁺, yEuⁿ⁺(y=0.0001–0.002) phosphors show an intense green emission band around 505 nm, while under the excitation of 264 nm, three emission bands centered around 396 nm (Bi³⁺), 505 nm (Eu²⁺) and 614 nm (Eu³⁺) are observed and tunable colors from blue-violet to green or white are achieved in these phosphors by varying the content of Eu. White-light emission with the color coordinate (0.312, 0.328) is obtained in Ca_2.978SiO₄Cl₂:0.01Bi³⁺, 0.01Li⁺, 0.002Euⁿ⁺(n =2, 3). Based on these results, the as-prepared CSC:Bi³⁺, Li⁺, Eu²⁺, Eu³⁺ phosphors can act as color-tunable and single-phase white emission phosphors for potential applications in UV-excited white LEDs.     

Improved photoluminescence,thermal stability and temperature sensing performances of K+ incorporated perovskite BaTiO3:Eu3+ red emitting phosphors

K⁺ ions incorporated perovskite Ba_(1−x)TiO₃:x Eu³⁺ red emitting phosphors synthesized via facile solid -state reaction method has been investigated in the current study. The photoluminescence and decay time behavior of Ba_(1−x−y)TiO₃:x Eu³⁺,yK⁺ phosphors are investigated as a function of Eu³⁺, K⁺ concentration and temperature. An intense and sharp emission peak at 615 nm was exhibited by the phosphors upon excitation at 397 nm (⁷F₀→⁵L₆). It can be credited to the hypersensitive electric dipole transition ⁵D₀→⁷F₂, which confirms that Eu³⁺ ions are located at non-centrosymmetric site of the host. The incorporation of K⁺ ions in optimized Ba_0.95TiO₃:0.05 Eu³⁺ phosphor resulted in a remarkable enhancement of photoluminescence intensity by 2.33 times as compared to bare one. The Ba_0.89TiO₃:0.05 Eu³⁺, 0.06 K⁺ phosphors were found to observe good temperature sensing along with adequate thermal stability even at 427 K. Furthermore, the photometric parameters have been also studied which are strongly facilitate the prepared ceramic samples as suitable for potential application in lighting.     

LiSr3SiO4Cl3—A novel host lattice for Eu2+-activated luminescent materials

Eu²⁺-activated LiSr₃SiO₄Cl₃ phosphors were successfully designed, and prepared at low calcination temperature (650 °C). The crystal structure, morphology, and photoluminescence properties have been investigated in detail. The LiSr₃SiO₄Cl₃ crystallizes in orthorhombic LiEu₃SiO₄Cl₃-type structure. Under 316 nm excitation, the phosphor exhibits an asymmetric emission band peaking at 495 nm, which is probably attributed to the 4f–5d transitions of Eu²⁺ in various crystallographic sites. Their luminescence properties are investigated as a function of activator concentration (Eu²⁺). The quenching concentration of Eu²⁺ in LiEu₃SiO₄Cl₃ is about 0.01 due to dipole–dipole interaction. The investigation indicates that Eu²⁺-activated LiEu₃SiO₄Cl₃ phosphor can be used as a green emitting phosphor for white LEDs.     

Gel-combustion assisted synthesis of eulytite-type Sr3Y(PO4)3 as a single host for narrow-band Eu3+ and broad-band Eu2+ emissions

A series of eulytite-type Sr₃Y_1-x(PO₄)₃:xEu³⁺ (x = 0–0.13) and Sr_3-yY(PO₄)₃:yEu²⁺ (y = 0–0.10) phosphors were successfully synthesized via gel-combustion and subsequent calcination in O₂ and Ar/H₂ atmospheres at 1250 °C, respectively. Detailed crystal structure analysis via Rietveld refinement showed that the phosphors were crystallized in the cubic system (space group I-43d, No. 220), in which the Eu³⁺ and Eu²⁺ activators reside at the Y³⁺ and Sr²⁺ sites, respectively. The trivalent Eu³⁺ ions (CN = 6) exhibited typical narrow-band luminescence via intra-4f⁶ transitions, with the red emission at ~ 615 nm being dominant (⁵D₀ → ⁷F₂ transition, FWHM = 15.9 ± 0.2 nm). The divalent Eu²⁺ ions (CN = 6 and 9) showed broad-band luminescence ranging from light-blue to blue via 4f⁶5d¹ → 4f⁷ transitions (FWHM = 115 ± 2 nm). The optimal Eu³⁺ and Eu²⁺ concentrations were determined to be 10 at% (x = 0.10) and 7 at% (y = 0.07), respectively, and the mechanisms of concentration quenching were discussed. The excitation/emission properties, fluorescence decay kinetics, CIE chromaticity, and particularly the rarely addressed thermal stability of the phosphors were investigated in detail.     

Synthesis and photoluminescence properties of Sr3(PO4)2:Re3+, Li+ (Re = Eu,Sm) red phosphors for white light-emitting diodes

Sr₃(PO₄)₂:Re³⁺, Li⁺ (Re = Eu, Sm) red phosphors were prepared via a high temperature solid state reaction, and their structure and luminescence properties were investigated. X-ray diffraction patterns indicate that the phase of as-prepared samples is in good agreement with standard Sr₃(PO₄)₂ structure. Under 395 nm excitation, the emission of Sr₃(PO₄)₂:Eu³⁺ consists of a strong peak centered at 622 nm and two weak peaks centered at 598 nm and 660 nm, which correspond to ⁵D₀→⁷F₂, ⁵D₀→⁷F₁ and ⁵D₀→⁷F₃ transitions, respectively. Also, the emission spectrum of Sr₃(PO₄)₂:Sm³⁺ shows three main peaks at 568 nm, 603 nm and 651 nm, which are attributed to ⁴G_5/2→⁶H_I/2 (I = 5, 7, 9) transitions of Sm³⁺. Furthermore, luminescence properties of Sr₃(PO₄)₂:Re³⁺, Li⁺ (Re = Eu, Sm) samples are enhanced significantly by Li⁺ ions doping as charge compensator. Results indicate that as-prepared Sr₃(PO₄)₂:Re³⁺, Li⁺ (Re = Eu, Sm) could be the potential red phosphors used in white light-emitting diodes.     

Synthesis and luminescence properties of single‐component Ca5(PO4)3F:Dy3+, Eu3+ white‐emitting phosphors

A series of Ca₅(PO₄)₃F:Dy³⁺, Eu³⁺ phosphors was synthesized by a solid‐state reaction method. The XRD results show that all as‐prepared Ca₅(PO₄)₃F:Dy³⁺, Eu³⁺ samples match well with the standard Ca₅(PO₄)₃F structure and the doped Dy³⁺ and Eu³⁺ ions have no effect on the crystal structure. Under near‐ultraviolet excitation, Dy³⁺ doped Ca₅(PO₄)₃F phosphor shows blue (486 nm) and yellow (579 nm) emissions, which correspond to ⁴F_9/2→⁶H_15/2 and ⁴F_9/2→⁶H_13/2 transitions respectively. Eu³⁺ co‐doped Ca₅(PO₄)₃F:Dy³⁺ phosphor shows the additional red emission of Eu³⁺ at 631 nm, and an improved color rendering index. The chromaticity coordinates of Ca₅(PO₄)₃F:Dy³⁺, Eu³⁺ phosphors also indicate the excellent warm white emission characteristics and low correlated color temperature. Overall, these results suggest that the Ca₅(PO₄)₃F:Dy³⁺, Eu³⁺ phosphors have potential applications in warm white light‐emitting diodes as single‐component phosphor.     

Luminescence and structural properties of Gd2SiO5:Eu3+ phosphors synthesized from the modified solid state method

This paper reports the preparation of Eu³⁺ doped Gadolinium oxyorthosilicate (Gd₂SiO₅:Eu³⁺) phosphor with different concentration of Eu³⁺(0.1–2.5 mol%) using the modified solid state reaction method. The synthesis procedure of the Gd₂SiO₅:Eu³⁺phosphor using inorganic materials such as Gd₂O₃, silicon dioxide (SiO₂), europium oxide (Eu₂O₃) and boric acid (H₃BO₃) as flux is discussed in detail. The prepared phosphor samples were characterized by using X-Ray Diffraction (XRD), Field Emission Gun Scanning Electron Microscopy (FEGSEM), Transmission Electron Microscopy (TEM), Fourier Transform Infrared Spectroscopy (FTIR), Photoluminescence (PL) and Thermoluminescence (TL). The Commission Internationale de l′Eclairage(CIE) coordinates were also calculated. The PL emission was observed in the 350–630 nm range for the Gd₂SiO₅:Eu³⁺ phosphor. PL excitation peaks were observed at 266, 275, 312 and 395 nm while the emission peaks were observed at 380, 416, 437, 545, 579, 589, 607, 615 and 628 nm. The emission peak at 615 nm was the most intense peak for all the different Eu³⁺ concentration samples. From the XRD data, using the Scherrer's formula, the average crystallite size of the Gd₂SiO₅:Eu³⁺ phosphor was calculated to be 33 nm. TL was carried out for the phosphor after both UV and gamma irradiation. The TL response of the Gd₂SiO₅:Eu³⁺ phosphor for the two different radiations was compared and studied in detail. It was found that the present phosphor can acts as a single host for red emission (1.5 mol%) for display devices and light emitting diode (LED) and white light emission for Eu³⁺(0.1 mol%) and it might be used as a TL dosimetric material for gamma dose detection.     

Near-UV light excited Eu3+, Tb3+, Bi3+ co-doped LaPO4 phosphors: Synthesis and enhancement of red emission for WLEDs

A series of single-phase Eu³⁺, Tb³⁺, Bi³⁺ co-doped LaPO₄ phosphors were synthesized by solid-state reaction at 800 °C. Crystal structures of the phosphors were investigated by X-ray diffraction (XRD). A monoclinic phase was confirmed. The excitation (PLE) and emission (PL) spectra showed that the phosphors could emit red light centered at 591 nm under the 392 nm excitation, which is in good agreement with the emission wavelength from near-ultraviolet (n-UV) LED chip (370–410 nm). The results of PLE and PL indicated that the co-doped Tb³⁺ and Bi³⁺could enhance emission of Eu³⁺ and the fluorescent intensities of the phosphors excited at 392 nm could reach to a maximum value when the doping molar concentration of Tb³⁺ and Bi³⁺ is about 2.0% and 2.0%, respectively. The co-doping Tb³⁺ and Bi³⁺ ions can strengthen the absorption of near UV region. They can also be efficient to sensitize the emission of Eu³⁺, indicating that the energy transfer occurs from Tb³⁺ and Bi³⁺ to Eu³⁺ ions. From further investigation it can be found that co-doping Tb³⁺ and Bi³⁺ ions can also induce excitation energy reassignment between ⁵D₀–⁷F₁ and ⁵D₀–⁷F₂ in these phosphors, and result in more energy assignment to ⁵D₀–⁷F₂ emission in LaPO₄:Eu³⁺, Tb³⁺, Bi³⁺. Our research results displayed that La_0.94PO₄:Eu³⁺_0.02, Tb³⁺_0.02, Bi³⁺_0.02 could be a new one and could provide a potential red-emitting phosphor for UV-based white LED.     

Tunable single-phased white-emitting Sr3Y(PO4)3:Dy3+ phosphors for near-ultraviolet white light-emitting diodes

Single-component white-emitting Sr₃Y(PO₄)₃:Dy³⁺ phosphors were synthesized by a high-energy deformation process. X-ray diffraction patterns showed the resulting crystallized phase to be of cubic structure, space group I-43d (no. 220). The broad-band excitation spectra between 250 and 500 nm were observed by monitoring the emission wavelength at 576 nm, which matches well with commercial near-UV or blue LED chips. Under a 352 nm excitation, the emission peaks were observed at 483 nm (blue), 576 nm (yellow), and 666 nm (red), corresponding to the ⁴F_9/2 → ⁶H_15/2, ⁴F_9/2 → ⁶H_13/2, and ⁴F_9/2 → ⁶H_11/2 transitions of Dy³⁺ ions. The optimized doping concentration of Dy³⁺ ion was 8 mol%. By controlling the Dy³⁺ ion concentration, tunable colors from white to yellow were obtained in Sr₃Y(PO₄)₃:Dy³⁺ phosphors. These results reveal that studied materials may be a promising candidate for white LED applications.     

Warm white-light generation in Ca9MgNa(PO4)7:Sr2+, Mn2+, Ln (Ln=Eu2+, Yb3+, Er3+, Ho3+, and Tm3+) under near-ultraviolet and near-infrared excitation

To obtain warm white-light emission, a series of Ca₉MgNa(PO₄)₇:Sr²⁺, Mn²⁺, Ln (Ln=Eu²⁺, Yb³⁺, Er³⁺, Ho³⁺, and Tm³⁺) phosphors were designed and their photoluminescence properties under near-ultraviolet and near-infrared excitation were studied. For near-ultraviolet excitation, blue-white emission is produced initially in the Eu²⁺ single-doped Ca₉MgNa(PO₄)₇, whose excitation band can well match with the near ultraviolet LED chip. By introducing Sr²⁺ ions into Ca₉MgNa(PO₄)₇:Eu²⁺, the Eu²⁺ emission band beyond 500 nm is enhanced obviously. Correspondingly, the emitting light color is tuned to nearly white. To generate warm white light further, Mn²⁺ is doped into the Ca_8.055MgNa(PO₄)₇:0.045Eu²⁺, 0.9Sr²⁺ and the correlated color temperature is decreased largely. For near-infrared excitation, the green, red, and blue emissions have been obtained in the Yb³⁺-Er³⁺, Yb³⁺-Er³⁺, and Yb³⁺-Er³⁺ co-doped Ca₉MgNa(PO₄)₇ phosphors, respectively. And warm white light is also produced in the Ca₉MgNa(PO₄)₇:Yb³⁺, Er³⁺, Ho³⁺, Tm³⁺ under 980 nm excitation.     

Energy transfer and multicolor tunable emission in single-phase Tb3+, Eu3+ co-doped Sr3La(PO4)3 phosphors

A series of green-to-red color-tunable Sr₃La(PO₄)₃:Tb³⁺, Eu³⁺ phosphors were prepared by high temperature solid-state method. The crystal structures, photoluminescence properties, fluorescence lifetimes, and energy transfer of Sr₃La(PO₄)₃:Tb³⁺, Eu³⁺ were systematically investigated in detail. The obtained phosphors show both a green emission from Tb³⁺ and a red emission from Eu³⁺ with considerable intensity under ultraviolet (UV) excitation (~377 nm). The emission colors of the phosphors can be tuned from green (0.304, 0.589) through yellow (0.401, 0.505) and eventually to red (0.557, 0.392) due to efficient Tb³⁺-Eu³⁺ energy transfer (ET). The Tb³⁺→Eu³⁺ energy transfer process was demonstrated to be quadrupole-quadrupole mechanism by Inokuti-Hirayama model, with maximum ET efficiency of 86.3%. The results indicate that the Sr₃La(PO₄)₃:Tb³⁺, Eu³⁺ phosphors might find potential applications in the field of lighting and displays.     

Preparation and Luminescence Properties of Blue‐emitting Phosphor Ba2Ca(PO4)2:Eu2+

Using the conventional high temperature solid‐state reaction method Ba₂Ca(PO₄)₂:Eu²⁺ phosphors were prepared. The phase structure, photoluminescence (PL) properties, and the PL thermal stability of the samples were investigated, respectively. Under the excitation at 365 nm, the phosphor exhibited an asymmetric broad‐band blue emission with peak at 454 nm, which is ascribed to the 4f–5d transition of Eu²⁺. It was further proved that the dipole–dipole interactions results in the concentration quenching of Eu²⁺ in Ba₂Ca_1?x (PO₄)₂:xEu²⁺ phosphors. When the temperature turned up to 150°C, the emission intensity of Ba₂Ca_0.99(PO₄)₂:0.01Eu²⁺ phosphor was 59.07% of the initial value at room temperature. The activation energy ΔE was calculated to be 0.30 eV, which proved the good thermal stability of the sample. All the properties indicated that the blue‐emitting Ba₂Ca(PO₄)₂:Eu²⁺ phosphor has potential application in white LEDs.     

Structural and spectral properties of red light emitting Eu3+ activated TiO2 nanophosphor for white LED application

The structural and luminescent properties of Eu³⁺ doped TiO₂ nanophosphors synthesized by low cost combustion method were investigated. The X-ray diffraction analysis revealed that crystallite size decreases with doping concentration. Lattice volume expansion occurred due to the substitution of Ti⁴⁺ ions by larger ionic radii ions Eu³⁺. FESEM images showed prepared phosphors to be nano size spherical shaped particles. Energy band gap of 3 mol% Eu³⁺ doped samples decreased to 3.15 eV due to doping effect. The Eu³⁺ doped TiO₂ nanophosphors exhibited main red emission peak centered at 616 nm under 395 nm UV light excitation. Concentration quenching was observed at 3 mol% doping, that has been ascribed to dipole-dipole interaction. The covalent nature of Eu-O bond and environment around Eu³⁺ ions were discussed using Judd-Ofelt (J-O) intensity parameters. Internal quantum efficiency was calculated using excited state lifetime ⁵D₀ state of Eu³⁺ ion and J-O theory. The CIE colour coordinates and colour purity were calculated using the spectral energy distribution function. Low excited state life time indicated that Eu³⁺ doped TiO₂ can be used as red emitting phosphor for white light emitting diode applications.     

Synthesis and photoluminescence enhancement of Ca3Sr3(VO4)4:Eu3+ red phosphors by co-doping with La3+

In this study, a series of red-emitting Ca₃Sr₃(VO₄)₄:Eu³⁺ phosphors co-doped with La³⁺ was prepared using the combustion method. The microstructures, morphologies, and photoluminescence properties of the phosphors were investigated. All Ca₃Sr₃(VO₄)₄:Eu³⁺, La³⁺ samples synthesized at temperatures greater than 700 ℃ exhibited the same standard rhombohedral structure of Ca₃Sr₃(VO₄)₄. Furthermore, the Ca₃Sr₃(VO₄)₄:Eu³⁺, La³⁺ phosphor was effectively excited by near-ultraviolet light of 393 nm and blue light of 464 nm. The strong excitation peak at 464 nm corresponded to the ⁷F₀→⁵D₂ electron transition of Eu³⁺. The strong emission peak observed at 619 nm corresponded to the ⁵D₀→⁷F₂ electron transition of Eu³⁺. Co-doping with La³⁺ significantly improved the emission intensity of Ca₃Sr₃(VO₄)₄:Eu³⁺ red phosphors. The optimum luminescence of the phosphor was observed at Eu³⁺ and La³⁺ concentrations of 5% and 6%, respectively. Moreover, co-doping with La³⁺ also improved the fluorescence lifetime and thermal stability of the Ca₃Sr₃(VO₄)₄:Eu³⁺ phosphor. The CIE chromaticity coordinate of Ca₃Sr₃(VO₄)₄:0.05Eu³⁺, 0.06La³⁺ was closer to the NTSC standard for red phosphors than those of other commercial phosphors; moreover, it had greater color purity than that of all the samples tested. The red emission intensity of Ca₃Sr₃(VO₄)₄:0.05Eu³⁺, 0.06La³⁺ at 619 nm was ~1.53 times that of Ca₃Sr₃(VO₄)₄:0.05Eu³⁺ and 2.63 times that of SrS:Eu²⁺. The introduction of charge compensators could further increase the emission intensity of Ca₃Sr₃(VO₄)₄:Eu³⁺, La³⁺ red phosphors. The phosphors synthesized herein are promising red-emitting phosphors for applications in white light-emitting diodes under irradiation by blue chips.     

Photoluminescence and LED application of β-SiAlON:Eu2+ green phosphor

We successfully prepared β-SiAlON:Eu²⁺ phosphors with composition of Eu_xSi_6?zAl_zO_yN_8?y (y = z ? 2x, x = 0.018, z = 0.23) by gas-pressured synthesis for application to LED. The crystal phase, microstructure, PL emission and thermal quenching properties were investigated in detail. The β-SiAlON:Eu²⁺ phosphors absorbed broad UV–vis spectral region, and showed a single intense broadband emission near 538 nm. The Stokes shift and zero-phonon line were calculated mathematically, and also estimated from the spectral data. The β-SiAlON:Eu²⁺ green phosphor showed superior thermal quenching properties compared to commercial silicate (SrBaSiO₄:Eu²⁺) green phosphor. The white light-emitting diode (LED) using the prepared β-SiAlON:Eu²⁺ green phosphor exhibited high color gamut, and good optical stability in high working temperature.