Synthesis and ethanol sensing properties of CuO nanorods coated with In2O3

CuO/In₂O₃ core–shell nanorods were fabricated using thermal evaporation and radio frequency magnetron sputtering. X-ray diffraction and transmission electron microscopy showed that both the cores and shells were crystalline. The multiple networked CuO/In₂O₃ core–shell nanorod sensors showed responses of 382–804%, response times of 36–54 s and recovery times of 144–154 s at ethanol (C₂H₅OH) concentrations ranging from 50 to 250 ppm at 300 °C. These responses were 2.3–2.8 times higher than those of the pristine CuO nanorod sensor over the same C₂H₅OH concentration range. The origin of the enhanced ethanol sensing properties of the core–shell nanorod sensor is discussed.     

Enhanced H2S sensing performance of TiO2-decorated α-Fe2O3 nanorod sensors

Pristine and TiO₂ nanoparticle-decorated Fe₂O₃ nanorods were synthesized via thermal oxidation of Fe thin foils, followed by the solvothermal treatment with titanium tetra isopropoxide (TTIP) and NaOH for TiO₂ nanoparticle-decoration. Subsequently, gas sensors were fabricated by connecting the nanorods with metal conductors. The structure and morphology of the pristine and TiO₂ nanoparticle-decorated Fe₂O₃ nanorods were examined via X-ray diffraction and scanning electron microscopy, respectively. The gas sensing properties of the pristine and TiO₂ nanoparticle-decorated Fe₂O₃ nanorod sensors with regard to H₂S gas were examined. The TiO₂ nanoparticle-decorated Fe₂O₃ nanorod sensor showed a stronger response to H₂S than the pristine Fe₂O₃ nanorod sensor. The responses of the pristine and TiO₂ nanoparticle-decorated Fe₂O₃ nanorod sensors were 2.6 and 7.4, respectively, when tested with 200 ppm of H₂S at 300 °C. The TiO₂ nanoparticle-decorated Fe₂O₃ nanorod sensor also showed a faster response and recovery than the sensor made from pristine Fe₂O₃ nanorods. Both sensors showed selectivity for H₂S over NO₂, SO₂, NH₃, and CO. The enhanced sensing performance of the TiO₂ nanoparticle-decorated Fe₂O₃ nanorod sensor compared to that of the pristine Fe₂O₃ nanorod sensor might be due to enhanced modulation of the conduction channel width, the decorated nanorods’ increased surface-to-volume ratios and the creation of preferential adsorption sites via TiO₂ nanoparticle decoration. The dominant sensing mechanism in the TiO₂ nanoparticle-decorated Fe₂O₃ nanorod sensor is discussed in detail.     

Ethanol sensing properties of networked In2O3 nanorods decorated with Cr2O3-nanoparticles

In₂O₃ nanorods decorated with Cr₂O₃ nanoparticles were synthesized by thermal evaporation of In₂S₃ powder in an oxidizing atmosphere followed by solvothermal deposition of Cr₂O₃ and their ethanol gas sensing properties were examined. The pristine and Cr₂O₃-decorated In₂O₃ nanorods exhibited responses of ~524% and ~1053%, respectively, to 500-ppm ethanol at 200 °C. The Cr₂O₃-decorated In₂O₃ nanorod sensor showed stronger electrical response to ethanol gas at 200 °C than the pristine In₂O₃ nanorod counterpart. The former also showed faster response and recovery than the latter. The pristine and Cr₂O₃-decorated In₂O₃ nanorod sensors showed the strongest response to ethanol gas at 250 and 200 °C, respectively. The Cr₂O₃-decorated In₂O₃ nanorod sensor showed selectivity for ethanol gas over other reducing gases. The underlying mechanism for the enhanced response, sensing speed and selectivity of the Cr₂O₃-decorated In₂O₃ nanorod sensor for ethanol gas is discussed.     

Enhanced NO2 sensing properties of Zn2SnO4-core/ZnO-shell nanorod sensors

Zn₂SnO₄-core/ZnO-shell nanorods were synthesized using a two-step process: synthesis of Zn₂SnO₄ nanorods the thermal evaporation of a mixture of ZnO, SnO₂, and graphite powders, followed by atomic layer deposition (ALD) of ZnO. The nanorods were 50–250 nm in diameter and a few to a few tens of micrometers in length. The cores and shells of the nanorods were face-centered cubic-structured single crystal Zn₂SnO₄ and wurtzite-structured single crystal ZnO, respectively. The multiple networked Zn₂SnO₄-core/ZnO-shell nanorod sensors showed a response of 173–498% to NO₂ concentrations of 1–5 ppm at 300 °C. These response values are 2–5 times higher than those of the Zn₂SnO₄ nanorod sensor over the same NO₂ concentration range. The NO₂ sensing mechanism of the Zn₂SnO₄core/ZnO-shell nanorods is discussed.     

Synthesis of Ag3PO4–ZnO nanorod composites with high visible-light photocatalytic activity

Ag₃PO₄ nanoparticles with 50–100 nm in size distributed on the surface of ZnO nanorods with ca. 20 nm in diameter and 1–2 μm in length have been synthesized by a facile method. The Ag₃PO₄–ZnO nanorod composites had much higher photocatalytic activity toward degradation of Rhodamine B (RhB) under visible light irradiation than pure ZnO nanorods, and had better recyclability and stability than pure Ag₃PO₄ nanoparticles. The Ag₃PO₄–ZnO nanorod composite with the molar ratio of Ag₃PO₄:ZnO = 1:40 exhibited the highest photodegradation efficiency of RhB (93%), which was 1.5 times of pure ZnO nanorods.     

Photooxidation of iodide ion on some semiconductor and non-semiconductor surfaces

In 80% aqueous ethanol, TiO₂ (anatase), ZrO₂, ZnO, V₂O₅, Fe₂O₃ and Al₂O₃ photocatalyze the oxidation of iodide ion but CdO and CdS do not; the wavelength of illumination is 365 nm. However, Fe₂O₃ fails to bring in a sustainable photocatalysis in 60% aqueous ethanol. The photooxidation of iodide ion on TiO₂, ZrO₂, ZnO, V₂O₅ and Al₂O₃ in 60% aqueous ethanol was studied as a function of [I⁻], amount of catalyst suspended, airflow rate, light intensity and solvent composition. The metal oxides examined show sustainable photocatalytic activity. Iodine formation is larger with illumination at 254 nm than at 365 nm. The mechanisms of photocatalysis on semiconductor and non-semiconductor surfaces have been discussed. Photocatalytic generation of iodine has been analyzed using a kinetic model. The photocatalytic efficiencies are of the order V₂O₅ > TiO₂ > ZrO₂ > ZnO > Al₂O₃ and V₂O₅ > TiO₂ > ZrO₂ > ZnO=Fe₂O₃ > Al₂O₃ in 60% and 80% aqueous ethanol.     

Controlled synthesis of Fe3O4@SnO2/RGO nanocomposite for microwave absorption enhancement

A ternary nanocomposite of Fe₃O₄@SnO₂/reduced graphene oxide (RGO) with different contents of SnO₂ nanoparticles was synthesized by a simple and efficient three-step method. The transmission electron microscopy and field emission scanning electron microscopy characterization display that plenty of Fe₃O₄@SnO₂ core–shell structure nanoparticles are well distributed on the surface of RGO sheets. The X-ray diffractograms show that the products consist of highly crystallized cubic Fe₃O₄, tetragonal SnO₂ and disorderedly stacked RGO sheets. The magnetic hysteresis measurement reveals the ferromagnetic behavior of the products at room temperature. The microwave absorption properties of paraffin containing 50 wt% products were investigated at room temperature in the frequency range of 2–18 GHz by a vector network analyzer. The electromagnetic data show that the maximum reflection loss is −45.5 dB and −29.5 dB for Fe₃O₄@SnO₂/RGO-1 and Fe₃O₄@SnO₂/RGO-2 nanocomposite, respectively. Meanwhile, the reflection loss less than −10 dB is up to 14.4 GHz and 13.8 GHz for Fe₃O₄@SnO₂/RGO-1 and Fe₃O₄@SnO₂/RGO-2 nanocomposite, respectively. It is believed that such nanocomposite could be used as promising microwave absorbers.     

Highly stable and selective ethanol sensor based on α-Fe2O3 nanoparticles prepared by Pechini sol–gel method

In the present work, α-Fe₂O₃ nanoparticles were successfully synthesized by Pechini sol–gel (PSG) method following annealing at 550 °C. The morphology and microstructure of the prepared α-Fe₂O₃ nanoparticles were characterized by scanning electron microscope (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and Raman analysis. The electrical and sensing properties were also investigated. The α-Fe₂O₃ based sensor showed good sensitivity and selectivity towards ethanol at the optimal temperature of 225 °C. Moreover, the sensor displayed good electrical and sensing stability. These results suggest the potential applications of α-Fe₂O₃ synthesized by Pechini sol–gel method as a sensor material for ethanol detection.     

Nanostructured perovskite oxides – LaMO3 (M=Al,Co, Fe) prepared by co-precipitation method and their ethanol-sensing characteristics

Nanostructured La-based perovskite oxides − LaMO₃ (M=Al, Co, Fe) were synthesized by a new co-precipitation procedure using metal nitrate and carbonate salts as starting materials. X-ray diffraction and energy dispersive X-ray spectroscopic results confirmed the formation of single-phase nanocrystalline perovskite oxides with high purity. Characterizations by scanning/transmission electron microscopy and nitrogen adsorption revealed that LaAlO₃ was produced in the form of rectangular porous nanorods exhibiting much larger surface area and porosity compared with densely aggregated LaCoO₃ particles and loosely clustered LaFeO₃ nanoparticles with cracked-egg morphologies. The materials were characterized for gas sensing towards ethanol at 200–350 °C. From gas-sensing results, the LaAlO₃ sensor displayed n-type gas-sensing behaviors with considerably higher ethanol response than p-type LaFeO₃ and LaCoO₃ sensors, respectively. In particular, the LaAlO₃ sensor exhibited a high response of 16.45–1000 ppm ethanol and excellent ethanol selectivity against NO₂, SO₂, CO and H₂ at 350 °C. The superior gas-sensing performances could be attributed to the effective receptor function, transducer function and utility factor of LaAlO₃ nanorod structures prepared by the co-precipitation method.     

A simple approach for the synthesis of bi-functional Fe3O4@WO3 − x core–shell nanoparticles with magnetic-microwave to heat responsive properties

A facile direct precipitation method has been developed for the synthesis of multi-functional magnetic, microwave to heat responsive properties with Fe₃O₄ nanoparticles as the core and WO_3 − x as the shell. Transmission electron microscopy (TEM) images revealed that the obtained bi-functional nanoparticles had a core-shell structure and a spherical morphology. The average size was ~ 250 nm, and the thickness of the shell was ~ 15 nm. The X-ray diffraction (XRD) patterns showed that a cubic spinel structure of Fe₃O₄ core and the WO_3 − x shell were obtained. The nanoparticles showed both strong magnetic, and unique microwave to heat responsive properties, which may lead to development of nanoparticles with great potential for applications in drug targeting delivery, controlled release drug, photo- and microwave-thermal combination therapy and water treatment.     

Sb2O3–ZnO nanospindles: A potential material for photocatalytic and sensing applications

This paper reports the facile synthesis, characterization and applications of Sb₂O₃–ZnO nanospindles. The nanospindles were synthesized by facile diethanolammine assisted hydrothermal process and characterized in detail in terms of their morphological, structural, compositional and optical properties. The detailed characterizations revealed that the prepared nanoellipsoids are well-crystalline, grown in high density and possessing good optical properties. Further, the as-synthesized Sb₂O₃–ZnO nanospindles were found to be an efficient photocatalyst for the degradation of methylene blue (MB) dye under UV light. Sb₂O₃–ZnO nanospindles were also used as an efficient electron mediator to fabricate a robust, highly sensitive and reproducible chemical sensor for the detection of thiourea in aqueous medium. The fabricated chemical sensor possesses high sensitivity of 6.54 µA mmol L⁻¹ cm⁻². The sensing calibration plot was found to be linear (R²=0.91423) over the large concentration range from 1.56 mmol L⁻¹ to 100 mmol L⁻¹. The obtained results confirmed that the Sb₂O₃–ZnO nanospindles may hold great potential for the removal of organic pollutants and for monitoring of thiourea in aqueous solution.     

Synthesis and enhanced gas sensing properties of flower-like ZnO/α-Fe2O3 core-shell nanorods

This paper reports a facile two-step synthesis route for the preparation of flower-like ZnO/α-Fe₂O₃ nanorods (NRs). Flower-like ZnO NRs with the average diameter about 810 nm and length about 4.5 µm were firstly synthesized via a chemical solution method, and then ZnO NRs was coated with a continuous α-Fe₂O₃ layer to form ZnO/α-Fe₂O₃ core-shell structure through an ionic-layer adsorption and reaction method. The gas-sensing results show that the ZnO/α-Fe₂O₃ NRs exhibit excellent sensitivity, selectivity, and response-recovery capacity to ethanol vapor at a low optimum temperature of 240 °C. In particular, compared with pure ZnO NRs and α-Fe₂O₃ nanoparticles (NPs), the ZnO/α-Fe₂O₃ NRs show an obvious improvement in gas sensing properties. The substantial improvement of sensing properties may be attributed to the unique microstructure and heterojunction formed between ZnO and α-Fe₂O₃.     

Fe3O4 nanoparticles encapsulated in electrospun porous carbon fibers with a compact shell as high-performance anode for lithium ion batteries

Fe₃O₄ nanoparticles encapsulated in porous carbon fibers (Fe₃O₄@PCFs) as anode materials in lithium ion batteries are fabricated by a facile single-nozzle electrospinning technique followed by heat treatment. A mixed solution of polyacrylonitrile (PAN) and polystyrene (PS) containing Fe₃O₄ nanoparticles is utilized to prepare hybrid precursor fibers of Fe₃O₄@PS/PAN. The resulted porous Fe₃O₄/carbon hybrid fibers composed of compact carbon shell and Fe₃O₄-embeded honeycomb-like carbon core are formed due to the thermal decomposition of PS and PAN. The Fe₃O₄@PCF composite demonstrates an initial reversible capacity of 1015 mAh g⁻¹ with 84.4% capacity retention after 80 cycles at a current density of 0.2 A g⁻¹. This electrode also exhibits superior rate capability with current density increasing from 0.1 to 2.0 A g⁻¹, and capacity retention of 91% after 200 cycles at 2.0 A g⁻¹. The exceptionally high performances are attributed to the high electric conductivity and structural stability of the porous carbon fibers with unique structure, which not only buffers the volume change of Fe₃O₄ with the internal space, but also acts as high-efficient transport pathways for ions and electrons. Furthermore, the compact carbon shell can promote the formation of stable solid electrolyte interphase on the fiber surface.     

Amelioration of the hydriding and dehydriding kinetics of Mg by reactive mechanical grinding with Ni and Fe2O3 purchased and prepared by spray conversion

The activated 76.5 wt%Mg–23.5 wt%Ni (Mg–Ni) has a lower hydriding rate, compared with Mg–23.5 wt%Ni heat-treated after melt spinning, due to the nonhomogeneous distribution of Ni particles in the mixture and the larger sizes of the particles. Among 76.5 wt%Mg–23.5 wt%Ni (Mg–Ni), 71.5 wt%Mg–23.5 wt%Ni–5 wt%Fe₂O₃ (Mg–Ni–O), and 71.5 wt%Mg–23.5 wt%Ni–5 wt% Fe₂O₃(spray conversion) (Mg–Ni–Osc) samples, Mg–Ni–Osc has the highest hydriding and dehydriding rates. The reactive mechanical grinding of Mg with Ni, purchased Fe₂O₃ or Fe₂O₃(spray conversion) is considered to facilitate nucleation and shorten diffusion distances of hydrogen atoms. After hydriding–dehydriding cycling, all the samples contain Mg₂Ni phase. The samples with Fe₂O₃ and Fe₂O₃(spray conversion) as starting materials contain Mg(OH)₂ phase after hydriding–dehydriding cycling as well as after reactive mechanical grinding.     

Magnetic,luminescent and core–shell structured Fe3O4@YF3:Ce3+,Tb3+ bifunctional nanocomposites

Bifunctional magnetic–luminescent nanocomposites with Fe₃O₄ nanoparticles as the cores and YF₃:Ce³⁺,Tb³⁺ as the shells were synthesized by a facile direct precipitation method. Transmission electron microscopy (TEM) images revealed that the obtained bifunctional nanocomposites had a core–shell structure, in a spherical shape with a size ranging from 160 to 220 nm, and the shell thickness of about 25 nm. The X-ray diffraction (XRD) patterns showed that a cubic spinel structure of Fe₃O₄ core and an orthogonal phase of YF₃ shell were obtained. Photoluminescence (PL) spectra confirmed that the nanocomposites displayed a strong green light emission. Magnetic measurements indicated that the obtained bifunctional nanocomposites exhibited a stronger magnetic behavior at room temperature. Therefore, the bifunctional nanocomposites are expected to develop many potential applications in biomedical fields.     

Fabrication of graphene nanosheet (GNS)–Fe3O4 hybrids and GNS–Fe3O4/syndiotactic polystyrene composites with high dielectric permittivity

Graphene nanosheet–Fe₃O₄ (GNS–Fe₃O₄) hybrids were obtained by a one-step solvothermal reduction of iron (III) acetylacetonate [Fe(acac)₃] and graphene oxide (GO) simultaneously, which had several advantages: (1) the Fe₃O₄ nanoparticles were firmly anchored on GNS surface even after mild ultrasonication; (2) the loading amount of Fe₃O₄ nanoparticles could be effectively controlled by changing the initial feeding weight ratio of Fe(acac)₃ to GO; (3) the Fe₃O₄ nanoparticles were homogeneously distributed on the GNS surface without much aggregation. Composites based on syndiotactic polystyrene (sPS) and GNS–Fe₃O₄ were prepared by a solution-blending method and the electric and dielectric properties of the resultant GNS–Fe₃O₄/sPS composites were investigated. The percolation threshold of GNS–Fe₃O₄ in the sPS matrix was determined to be 9.41 vol.%. Slightly above the percolation threshold with 9.59 vol.% of GNS–Fe₃O₄, the GNS–Fe₃O₄/sPS composite showed a high dielectric permittivity of 123 at 1000 Hz, which was 42 times higher than that of pure sPS. The AC electrical conductivity at 1000 Hz increased from 3.6 × 10⁻¹⁰ S/m for pure sPS to 2.82 × 10⁻⁴ S/m for GNS–Fe₃O₄/sPS composite containing 10.69 vol.% of GNS–Fe₃O₄, showing an obvious insulator-semiconductor transition.     

Nanoseed-assisted rapid formation of ultrathin ZnO nanorods for efficient room temperature NO2 detection

The influence of ZnO nanoseeds on the formation of ZnO nanorods from ε-Zn(OH)₂ in NaOH solution at 80 °C was investigated, using ZnO nanoparticles with a diameter of 4–10 nm as the seeds. The experimental results indicated that the presence of ZnO nanoseeds promoted the rapid heterogeneous formation of ultrathin ZnO nanorods. Compared with the ZnO submicron rods with a diameter of 0.5–1.0 µm, the ultrathin ZnO nanorods with a diameter of 10–15 nm were found to be more sensitive for detecting NO₂ at room temperature owing to their higher variation of channel conduction to the diameter.     

Hydrothermal synthesis of dumbbell-shaped ZnO microstructures

Dumbbell-shaped ZnO microstructures have been successfully synthesized by a facile hydrothermal method using only Zn(NO₃)₂·6H₂O and NH₃·H₂O as raw materials at 150 °C for 10 h. The results from X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM) show that the prepared ZnO samples exhibit dumbbell-shaped morphology and hexagonal wurtzite structure. The length of ZnO dumbbells is about 5–20 μm, the diameters of the two ends and the middle part are about 1–5 μm and 0.5–3 μm, respectively. The dumbbell-shaped ZnO microstructures may be formed by self-assembly of ZnO nanorods with 1–5 μm in length and 100–200 nm in diameter. The photoluminescence (PL) spectrum of dumbbell-shaped ZnO microstructures at room temperature shows three emission peaks at about 362, 384 and 485 nm.     

Continuous flame aerosol synthesis of carbon-coated nano-LiFePO4 for Li-ion batteries

Core–shell, nano-sized LiFePO₄-carbon particles were made in one step by scalable flame aerosol technology at 7 g/h. Core LiFePO₄ particles were made in an enclosed flame spray pyrolysis (FSP) unit and were coated in-situ downstream by auto thermal carbonization (pyrolysis) of swirl-fed C₂H₂ in an O₂-controlled atmosphere. The formation of acetylene carbon black (ACB) shell was investigated as a function of the process fuel-oxidant equivalence ratio (EQR). The core–shell morphology was obtained at slightly fuel-rich conditions (1.0<EQR<1.07) whereas segregated ACB and LiFePO₄ particles were formed at fuel-lean conditions (0.8<EQR<1). Post-annealing of core–shell particles in reducing environment (5 vol% H₂ in argon) at 700 °C for up to 4 h established phase pure, monocrystalline LiFePO₄ with a crystal size of 65 nm and 30 wt% ACB content. Uncoated LiFePO₄ or segregated LiFePO₄–ACB grew to 250 nm at these conditions. Annealing at 800 °C induced carbothermal reduction of LiFePO₄ to Fe₂P by ACB shell consumption that resulted in cavities between carbon shell and core LiFePO₄ and even slight LiFePO₄ crystal growth but better electrochemical performance. The present carbon-coated LiFePO₄ showed superior cycle stability and higher rate capability than the benchmark, commercially available LiFePO₄.     

Ethanol sensing properties of tungsten oxide nanorods prepared by microwave hydrothermal method

Tungsten oxide nanorods have been prepared by a simple microwave hydrothermal (MH) method via Na₂SO₄ as structure-directing agent at 180 °C for 20 min. The structure and morphology of the products are characterized by X-ray powder diffraction (XRD) and transmission electron microscopy (TEM). The obtained nanorods are about 20–50 nm in diameter and several micrometers in length. The ethanol sensing property of as-prepared tungsten oxide nanorods is studied at ethanol concentration of 10–1000 ppm and working temperature of 370–500 °C. It was found that the sensitivity depended on the working temperatures and also ethanol concentration. The results show that the tungsten oxide nanorods can be used to fabricate high performance ethanol sensors.