Steam reforming of methanol using Cu-ZnO catalysts supported on nanoparticle alumina

Methanol steam reforming was studied over several catalysts made by deposition of copper and zinc precursors onto nanoparticle alumina. The results were compared to those of a commercially available copper, zinc oxide and alumina catalyst. Temperature programmed reduction, BET surface area measurements, and N₂O decomposition were used to characterize the catalyst surfaces. XRD was used to study the bulk structure of the catalysts, and XPS was used to determine the chemical states of the surface species. The nanoparticle-supported catalysts achieved similar conversions as the commercial reference catalyst but at slightly higher temperatures. However, the nanoparticle-supported catalysts also exhibited a significantly lower CO selectivity at a given temperature and space time than the reference catalyst. Furthermore, the turnover frequencies of the nanoparticle-supported catalysts were higher than that of the commercial catalyst, which means that the activity of the surface copper is higher. It was determined that high alumina concentrations ultimately decrease catalytic activity as well as promote undesirable CH₂O formation. The lower catalytic activity may be due to strong Cu-Al₂O₃ interactions, which result in Cu species which are not easily reduced. Furthermore, the acidity of the alumina support appears to promote CH₂O formation, which at low Cu concentrations is not reformed to CO₂ and H₂. The CO levels present in this study are above what can be explained by the reverse water-gas-shift (WGS) reaction. While coking is not a significant deactivation pathway, migration of ZnO to the surface of the catalyst (or of Cu to the bulk of the catalyst) does explain the permanent loss of catalytic activity. Cu₂O is present on the spent nanoparticle catalysts and it is likely that the Cu⁺/Cu⁰ ratio is of importance both for the catalytic activity and the CO selectivity.     

Methanol synthesis pathway over Cu/ZrO2 catalysts: a time‐resolved DRIFT 13C‐labelling experiment

X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) have been used to characterize a series of Cu/Ce/Al₂O₃ catalysts. Catalysts were prepared by incipient wetness impregnation using metal nitrate and alkoxide precursors. Catalyst loadings were held constant at 12 wt% CuO and 5.1 wt% CeO₂. Mixed oxide catalysts were prepared by impregnation of cerium first, followed by copper. The information obtained from surface and bulk characterization has been correlated with CO and CH₄ oxidation activity of the catalysts. Cu/Al₂O₃ catalysts prepared using Cu(II) nitrate (CuN) and Cu(II) ethoxide (CuA) precursors consist of a mixture of copper surface phase and crystalline CuO. The CuA catalyst shows higher dispersion, less crystalline CuO phase, and lower oxidation activity for CO and CH₄ than the CuN catalyst. For Cu/Ce/Al₂O₃ catalysts, Ce has little effect on the dispersion and crystallinity of the copper species. However, Cu impregnation decreases the Ce dispersion and increases the amount of crystalline CeO₂ present in the catalysts, particularly in Ce modified alumina prepared using cerium alkoxide precursor (CeA). Cerium addition dramatically increases the CO oxidation activity, however, it has little effect on CH₄ oxidation. This revised version was published online in July 2006 with corrections to the Cover Date.     

EXAFS and XPS Investigations of Cu/ZnO Catalysts and Their Interaction with CO and Methanol

Several investigations have been carried out on Cu/ZnO catalysts by employing extended Xray absorption fine structure (EXAFS) and Xray photoelectron spectroscopy (XPS). EXAFS investigations of Cu/ZnO catalysts subjected to hydrogen reduction show the presence of Cu¹⁺ species and Cu microclusters. The proportion of Cu¹⁺ depends on the rate of increase of the reduction temperature and on the amount of alumina added. An XPS study of the interaction of CO with model Cu/ZnO catalysts prepared in situ in the electron spectrometer shows the formation of CO₂ ^-, CO₃ ^2- and C₂O₄ ^2- species, their proportion relative to CO increasing with the Cu¹⁺/Cu⁰ ratio. A study of the interaction of CH₃OH with Cu clusters deposited on ZnO films reveals reversible molecular adsorption and the formation of CH₃O on clean Cu clusters. If the Cu clusters are pretreated with oxygen, however, both CH₃O and HCOO^- species are produced. Model Cu/ZnO catalyst surfaces containing both Cu¹⁺ and Cu⁰ species show interesting oxidation properties. On a Cu⁰-rich catalyst surface, only the CH₃O species is formed on interaction with CH₃OH. On a Cu¹⁺rich surface, the HCOO^- ion is the predominant species.     

Highly Active CNT-Promoted Cu–ZnO–Al2O3 Catalyst for Methanol Synthesis from H2/CO/CO2

With types of in-house-synthesized multi-walled carbon nanotubes (CNTs) and the nitrates of the corresponding metallic components, highly active CNT-promoted Cu–ZnO–Al₂O₃ catalysts, symbolized as Cu _i Zn _j Al _k -x%CNTs, were prepared by the co-precipitation method. Their catalytic performance for methanol synthesis from H₂/CO/CO₂ was studied and compared with the corresponding CNT-free co-precipitated catalyst, Cu _i Zn _j Al _k . It was shown experimentally that appropriate incorporation of a minor amount of the CNTs into the Cu _i Zn _j Al _k could significantly increase the catalyst activity for methanol synthesis. Under the reaction conditions of 493 K, 5.0 MPa, H_2/CO/CO₂/N₂ = 62/30/5/3 (v/v), GHSV = 8000 h^-1, the observed CO conversion and methanol formation rate over a co-precipitated catalyst of Cu₆Zn₃Al₁-12.5%CNTs reached 36.8% and 0.291 mol CH₃OH s^-1 (m²-surf. Cu)^-1, which was about 44 and 25% higher than those (25.5% and 0.233 mol CH₃OH s^-1 (m²-surf. Cu)^-1) over the corresponding CNT-free co-precipitated catalyst, Cu₆Zn₃Al₁. Addition of a minor amount (10–15 wt%) of the CNTs to the Cu₆Zn₃Al₁ catalyst was found to considerably increase specific surface area, especially Cu surface area of the catalyst. H₂-TPD measurements revealed that the CNTs and the pre-reduced CNT-promoted catalyst systems could reversibly adsorb and store a considerably greater amount of hydrogen under atmospheric pressure at temperatures ranging from room temperature to 573 K. This unique feature would be beneficial for generating microenvironments with higher stationary-state concentration of active hydrogen adspecies on the surface of the functioning catalyst, especially at the interphasial active sites since the highly conductive CNTs might promote hydrogen spillover from the Cu sites to the Cu/Zn interphasial active sites, and thus be favorable for increasing the rate of the CO hydrogenation reactions. Alternatively, the operation temperature for methanol synthesis over the CNT-promoted catalysts can be 15–20 degrees lower than that over the corresponding CNT-free contrast system. This would contribute considerably to an increase in equilibrium CO conversion and CH₃OH yield. The results of the present work indicated that the CNTs could serve as an excellent promoter.     

Comparative Study on Catalytic Performances for Low-temperature CO Oxidation of Cu–Ce–O and Cu–Co–Ce–O Catalysts

Two series of Cu–Ce–O and Cu–Co–Ce–O catalysts were prepared by co-precipitation method. The prepared catalysts were characterized by XRD, IR, TPR, XPS, BET and ICP-AES. The catalytic activities of the catalysts for low-temperature CO oxidation were evaluated through a microreactor-GC system. TPR results indicate that the addition of cobalt to the Cu–Ce–O can increase the dispersion of copper oxide, and the interaction between cobalt and copper can enhance the reducibility of each other. XPS analysis show that Ce⁴⁺, Cu²⁺, along with Co₃O₄, are present on the surface of Cu_0.4Co_0.6Ce₄ catalyst. The Co/Cu atomic ratio and the calcination temperature have significant effect on the activities of the catalysts. Compared with Cu₁Ce₄ catalyst, the Cu_0.4Co_0.6Ce₄ catalyst has better activity and thermal stability.     

Dehydrogenation of cyclohexanol on Cu–ZnO/SiO2 catalysts: The role of copper species

For the dehydrogenation of cyclohexanol a series of Cu–ZnO/SiO₂ catalysts with various Cu to ZnO molar ratios was prepared using the impregnation method, with the loading of copper fixed at 9.5 at.%. The catalysts were characterized by XPS, H₂–N₂O titration, BET, H₂-TPR, NH₃-TPD and XRD techniques. The results indicate that the addition of ZnO can improve the dispersion of copper species on reduced Cu–ZnO/SiO₂ (CZS) catalysts. Cu⁰ and Cu⁺ species were found on the reduced CZS catalysts surface, and the amount of Cu⁺ increased with the content of ZnO increasing. The addition of ZnO increased the acidity of the CZS catalysts. However, only Cu⁰ species can be found on the reduced Cu/SiO₂ (CS) catalyst surface. According to the reaction results, we found that the selectivity to phenol was related to the amount of Cu⁺ species, the Cu⁺ species should be the active sites for the production of phenol, the Cu⁰ is responsible for cyclohexanol dehydrogenation to cyclohexanone.     

Water–Gas Shift Reaction Over Aluminum Promoted Cu/CeO2 Nanocatalysts Characterized by XRD, BET, TPR and Cyclic Voltammetry (CV)

A series of aluminum promoted Cu/CeO₂ nanocatalysts with aluminum content in the range of 0–5wt.% were prepared by co-precipitation method and examined with respect to their catalytic performance for the water–gas shift (WGS) reaction. The catalysts were characterized by XRD, BET, H₂-TPR and cyclic voltammetry (CV) techniques. The results indicate that catalytic activity increases with the aluminum content at first, but then decreases with the further increase of aluminum content. Hereinto, Cu/CeO₂ catalyst doped with 1 wt.% of aluminum shows the highest catalytic activity (CO conversion reaches 84.4% at 200 °C) and thermal stability for WGS reaction. Correlation to the results from above characterization, it is found that the variation of catalytic activity is in very agreement with that of the surface area, the area of peak γ (i.e., the reduction of surface copper oxide (crystalline forms) interacted with surface oxygen vacancies on ceria), and the area of peak C₂ and in cyclic voltammetry process), respectively. Enough evidence was found for the fact that the metallic copper (Cu⁰) interacted with surface oxygen vacancies on ceria is the active site for WGS reaction over Cu/CeO₂ catalysts.     

An EXAFS study of Cu/ZnO and Cu/ZnO-Al2O3 methanol synthesis catalysts

Cu K-absorption edge and EXAFS measurements on binary Cu/ZnO and ternary Cu/ ZnO-Al₂O₃ catalysts of varying compositions on reduction with hydrogen at 523 K, show the presence of Cu microclusters and a species of Cu¹⁺ dissolved in ZnO apart from metallic Cu and Cu₂O. The proportions of different phases critically depend on the heating rate especially for catalysts of higher Cu content. Accordingly, hydrogen reduction with a heating rate of 10 K/min predominantly yields the metal species (>50%), while a slower heating rate of 0.8 K/min enhances the proportion of the Cu¹⁺ species ( 60%). Reduced Cu/ZnO-Al₂O₃ catalysts show the presence of metallic Cu (upto 20%) mostly in the form of microclusters and Cu¹⁺ in ZnO as the major phase ( 60%). The addition of alumina to the Cu/ZnO catalyst seems to favour the formation of Cu¹⁺/ZnO species.     

A highly efficient Cu/ZnO/Al2O3 catalyst via gel-coprecipitation of oxalate precursors for low-temperature steam reforming of methanol

The impact of preparation methods on the structure and catalytic behavior of Cu/ZnO/Al₂O₃ catalysts for H₂ production from steam reforming of methanol (SRM) has been reported. The results show that the nanostructured Cu/ZnO/Al₂O₃ catalyst obtained by a novel gel-coprecipitation of oxalate precursors has a high specific surface area and high component dispersion, exhibiting much higher activity in the SRM reaction as compared to the catalysts prepared by conventional coprecipitation techniques. It is suggested that the superior catalytic performance of the oxalate gel-coprecipitation-derived Cu/ZnO/Al₂O₃ catalyst could be attributed to the generation of “catalytically active” copper material with a much higher metallic copper specific surface as well as a stronger Cu–Zn interaction due to an easier incorporation of zinc species into CuC₂O₄ · x H₂O precursors as a consequence of isomorphous substitution between copper and zinc in the oxalate gel-precursors.     

Effects of catalyst composition on methanol synthesis from CO2/H2

Effects of catalyst composition have been studied for Cu/support and Cu/ZnO/supports in methanol synthesis from CO₂/H₂. A strong effect of support has been observed. Different supports brought about different behavior in temperature-programmed reduction of copper, different copper surface areas, and different catalytic activity and selectivity. It seemed possible to find catalyst supports that might perform better than commercial Cu/ZnO/Al₂O₃ catalysts. A correlation was observed between catalytic activity and the copper surface area which was varied by using different supports. However, the sup]>orts appeared to influence other catalytic properties as well, for example, the surface oxygen coverage.     

Effect of Pretreatment Atmosphere on CuO/TiO2 Activities in NO + CO Reaction

Using TiO₂ as carrier, CuO/TiO₂ catalysts with different CuO loading were prepared by the impregnation method. The catalytic activities in NO+CO reaction were examined with a micro-reactor gas chromatography reaction system and the methods of TPR, XPS and NO-TPD. It was found that the catalytic activities were affected by pretreatment atmosphere, i.e. H₂ atmosphere > reduction–reoxidation > 10%CO/He > reaction gas (fresh sample). NO decomposition was better by low-valence Cu species than by high-valence Cu species, i.e. Cu⁰>Cu⁺>Cu²⁺. The XPS results indicated that Cu species on CuO/TiO₂ were Cu⁰, Cu⁺, normal Cu²⁺(Cu²⁺(I)) and chain-structured Cu²⁺(Cu²⁺(II)) as –Cu–O–Ti–O–. The activities of Cu²⁺(II) were much higher than that of Cu²⁺(I), but both species were very unstable in the reaction atmosphere and easily reduced by CO, which accounted for the variable activities of fresh catalysts with increasing reaction temperature. In NO+CO reaction, the redox process was a cycle of Cu⁺–Cu²⁺(I) at low reaction temperature but was a cycle of Cu⁰–Cu⁺ at high reaction temperature. As shown by NO-TPD, high catalytic activities could be attributed to the following factors, e.g. oxygen caves on the catalyst’s surface after pretreatment with H₂ and reduction–reoxidation, formation of Cu⁰ after pretreatment with H₂, and increment of Cu species dispersion and formation of Cu²⁺(II) after pretreatment with reduction–reoxidation.     

Synthesis of DME from syngas on the bifunctional Cu–ZnO–Al2O3/Zr-modified ferrierite: Effect of Zr content

The catalytic activity on the coprecipitated Cu–ZnO–Al₂O₃/Zr-ferrierite (CZA–ZrFER) with different Zr content from 0 to 5 wt.% was investigated for the direct synthesis of dimethylether (DME) from H₂-deficient and biomass-derived model syngas (H₂/CO molar ratio = 0.93). The catalytic functionalities, such as CO conversion and DME selectivity, showed their maxima on the bifunctional catalyst with 3 wt.% Zr-modified ferrierite. Detailed characterization studies were conducted on the catalysts to measure their properties such as surface area, acidity by temperature-programmed desorption of ammonia (NH₃-TPD), reducibility of Cu oxide by temperature-programmed reduction (TPR), copper surface area measurements by N₂O titration method, electronic states of copper by IR analysis and particle size measurement by XRD and TEM analysis. The number of acid sites measured by NH₃-TPD on the bifunctional catalysts decreased monotonously with the increase of Zr content, meanwhile, the acidic strength is found to be minimal on the catalyst showing best performance. The reducibility of copper oxide and the surface area of metallic copper also exhibited their maximum values at the same Zr composition indicating that these are responsible for the optimum functionality of the bifunctional CZA–ZrFER catalyst. The role of easily reducible copper species with small particle size and the suppressed strong acidic sites is also emphasized in the consecutive reaction from syngas to DME on the bifunctional catalyst. The different behavior of intrinsic rate of the bifunctional catalysts is also well correlated with the metallic surface area of copper and the amount of acidic sites with their acidic strength.     

Influence of preparation method on performance of Cu(Zn)(Zr)-alumina catalysts for the hydrogen production via steam reforming of methanol

The selective production of hydrogen via steam reforming of methanol (SRM) was performed using prepared catalysts at atmospheric pressure over a temperature range 200–260^∘C. Reverse water gas shift reaction and methanol decomposition reactions also take place simultaneously with the steam reforming reaction producing carbon monoxide which is highly poisonous to the platinum anode of PEM fuel cell, therefore the detailed study of effect of catalyst preparation method and of different promoters on SRM has been carried out for the minimization of carbon monoxide formation and maximization of hydrogen production. Wet impregnation and co-precipitation methods have been comparatively examined for the preparation of precursors to Cu(Zn)(Al₂O₃) and Cu(Zn)(Zr)(Al₂O₃). The catalyst preparation method affected the methanol conversion, hydrogen yield and carbon monoxide formation significantly. Incorporation of zirconia in Cu(Zn)(Al₂O₃) catalyst enhanced the catalytic activity, hydrogen selectivity and also lower the CO formation. Catalyst Cu(Zn)(Zr)(Al₂O₃) with composition Cu/Zn/Zr/Al:12/4/4/80 prepared by co-precipitation method was the most active catalyst giving methanol conversion up to 97% and CO concentration up to 400 ppm. Catalysts were characterized by atomic absorption spectroscopy (AAS), Brunauer-Emett-Teller (BET) surface area, pore volume, pore size and X-ray powder diffraction (XRPD). The XRPD patterns revealed that the addition of zirconia improves the dispersion of copper which resulted in the better catalytic performance of Cu(Zn)(Zr)(Al₂O₃). The time-on-stream (TOS) catalysts stability test was also conducted for which the Cu(Zn)(Zr)(Al₂O₃) catalyst gave the consistent performance for a long time compared to other catalysts.     

Supported PdCl2CuCl2 catalysts for carbon monoxide oxidation II. XAFS characterization

A heterogenized Wacker catalyst system in which pores of a high surface area alumina were filled with an aqueous solution of PdCl₂CuCl₂ was active for the oxidation of CO near room temperature. The structure of the catalyst was studied by X-ray absorption fine structure (XAFS). The active phase of Pd was a Pd¹¹ species containing chlorine and, probably, carbonyl ligands. Direct interaction of PdPd or PdCu was not detected. The active phase of copper was found to be solid Cu₂Cl(OH)₃ particles in agreement with the X-ray diffraction (XRD) results. The presence of Cu was essential to keep the Pd in the Pd¹¹ state during the reaction. The rates of CO oxidation measured at temperatures of 30–70°C showed a minimum at 40°C, which was attributable partly to an unusual structure change of the active palladium species during the reaction at this temperature.     

CO Poisoning of Ethylene Hydrogenation over Pt Catalysts: A Comparison of Pt(111) Single Crystal and Pt Nanoparticle Activities

The ethylene hydrogenation reaction was studied on two platinum model catalyst systems in the presence of carbon monoxide to examine poisoning effects. The catalysts were a Pt(111) single crystal and lithographically fabricated platinum nanoparticles deposited on alumina. Gas chromatographic results for Pt(111) show that CO adsorption reduces the turnover rate from 10¹ to 10^-2 molecules/Pt site/s at 413 K, and the activation energy for hydrogenation on the poisoned surface becomes 20.2 ± 0.1 kcal/mol. The activation energy for ethylene hydrogenation over Pt(111) in the absence of CO is 10.8 kcal/mol. The Pt nanoparticle system shows the same rate for the reaction as over Pt(111) in the absence of CO. When CO is adsorbed on the Pt nanoparticle array, the rate of the reaction is reduced from 10² to 10⁰ nmol/s at 413 K. However, the activation energy remains largely unchanged. The Pt nanoparticles show an apparent activation energy for ethylene hydrogenation of 10.2 ± 0.2 kcal/mol in the absence of CO and 11.4 ± 0.6 kcal/mol on the CO-poisoned nanoparticle array. This is the first observation of a significant difference in catalytic behavior between Pt(111) and the Pt nanoparticle arrays. It is proposed that the active sites at the oxide--metal interface are responsible for the difference in activation energies for the hydrogenation reaction over the two model platinum catalysts.     

Supported Cu Catalysts with Yttria-Doped Ceria for Steam Reforming of Methanol

The steam reforming of methanol was studied over Cu/Al₂O₃ catalysts with the addition of yttria-doped ceria (YDC). The YDC-modified catalysts were prepared by impregnating a -Al₂O₃ support with Y and Ce then with Cu. The addition of YDC drastically enhanced the activity of Cu/Al₂O₃ in the methanol reforming reaction. The enhanced activity was attributed to the increase of Cu⁺ species by YDC in the methanol reforming environment. However, the addition of YDC decreased the copper dispersion. The Cu dispersion could be enhanced by adding chromium oxide. The addition of YDC and Cr where Al₂O₃ was first impregnated with Cr then with YDC showed the most pronounced enhancement of the catalyst activity. At reaction temperatures of 200250 °C, the CO concentration in the products was smaller than 0.1%.     

CO2 Hydrogenation to Methanol Over Cu/ZnO/Al2O3 Catalysts Prepared by a Novel Gel-Network-Coprecipitation Method

A novel gel-network-coprecipitation process has been developed to prepare ultrafine Cu/ZnO/Al₂O₃ catalysts for methanol synthesis from CO₂ hydrogenation. It is demonstrated that the gel-network-coprecipitation method can allow the preparation of the ultrafine Cu/ZnO/Al₂O₃ catalysts by homogeneous coprecipitation of the metal nitrate salts in the gel network formed by gelatin solution, which makes the metallic copper in the reduced catalyst exist in much smaller crystallite size and exhibit a much higher metallic copper-specific surface area. The effect of the gel concentration of gelatin on the structure, morphology and catalytic properties of the Cu/ZnO/Al₂O₃ catalysts for methanol synthesis from hydrogenation of carbon dioxide was investigated. The Cu/ZnO/Al₂O₃ catalysts prepared by the gel-network-coprecipitation method exhibit a high catalytic activity and selectivity in CO₂ hydrogenation to methanol.     

Role of ZnO in Cu/ZnO/Al2O3 catalyst for hydrogenolysis of butyl butyrate

For hydrogenolysis of butyl butyrate (BB), a series of Cu/ZnO/Al₂O₃ catalysts with different metal compositions were prepared, and characterized by N₂O chemisorption for measuring Cu surface area and by chromatographic experiment for determining the heat of BB adsorption. As a result, the presence of ZnO in Cu-based catalysts was found to enhance the catalytic activity of Cu due to dual function of ZnO. The Cu surface area was linearly correlated with the butanol productivity, demonstrating that ZnO exerts the structural function in Cu/ZnO/Al₂O₃ catalysts. Additionally, the role of ZnO as a chemical contributor was revealed such that its presence leads to lower activation energy of the surface reaction, thus resulting in higher Cu catalytic activity obtained at a low temperature such as 200 °C. Consequently, optimizing the Cu/Zn ratio in Cu/ZnO/Al₂O₃ catalyst is required to tune its structural and chemical characteristics of Cu metals, and thus to obtain a higher activity on the hydrogenolysis reaction.     

Characterization and catalytic properties of the CuO/SiO2 catalysts prepared by precipitation-gel method in the hydrogenolysis of glycerol to 1,2-propanediol: Effect of residual sodium

The effect of residual sodium on the CuO/SiO₂ catalysts prepared by precipitation-gel (PG) method has been investigated in correlation with the detailed characteristics of active component performance and catalytic performance in glycerol hydrogenolysis. Characterization of the catalysts showed that the residual sodium had a negative effect on the chemical–physical properties of the catalysts, such as the BET surface area, the dispersion of copper, and the reducibility of Cu²⁺ species as well as the adsorbility of reactant molecules. As a consequence, the conversion and selectivity of the catalysts in glycerol reactions generally decreased with increasing sodium content. The leaching of sodium from catalyst surface as a base could, however, on the one hand, weakly promote the activity of the catalyst, and on the other hand, could help retard the leaching of the active copper component and reduce the deactivation rate of the catalyst. The glycerol hydrogenolysis reaction is supposed to be a structure-sensitive reaction, in which copper particle sizes lower than a critical limit or those that did not fulfill a certain ensemble requirement were not active for glycerol reaction. Such details explained the lower TOFs of the catalysts with much smaller sizes. A certain amount of sodium is deduced to be needed for CuO/SiO₂ catalyst to exhibit both high catalytic activity and good stability. In addition, a reaction mechanism based on the effect of sodium on the activity and selectivity in glycerol hydrogenolysis has been proposed.     

Cu–ZrO2 Catalysts for Water-gas-shift Reaction at Low Temperatures

A series of Cu–ZrO₂ catalysts with Cu content in the range of 10–70 at.% Cu (=100×Cu/(Cu+Zr)) were prepared by coprecipitation, and their performances were tested for the water-gas-shift (WGS) reaction. The activity of the catalyst increased with Cu loading and, depending on the loading, the activity was comparable to or better than the activity of a conventional Cu–ZnO–Al₂O₃ catalyst at low temperatures below 473 K. Characterization of the catalysts revealed that the amount of Cu⁺ present on the catalyst surface, after being reduced by a H₂ mixture at 573 K, was well correlated with the activity of the catalyst, indicating that the Cu⁺ species were the active sites of the WGS reaction. The easy redox between Cu²⁺ and Cu⁺ during the WGS reaction was considered to be responsible for the high activity of Cu–ZrO₂ at low temperatures. A reaction mechanism based on the redox was proposed.