Depositional influences on porewater arsenic in sediments of a mining-contaminated freshwater lake

Arsenic-containing minerals mobilized during mining activities and deposited to Lake Coeur d'Alene (CDA), Idaho sediments represent a potential source of soluble As to the overlying water. Our objective was to delineate the processes controlling porewater As concentrations within Lake CDA sediments. Sediment and porewater As concentrations were determined, and solid-phase As associations were probed using X-ray absorption near-edge structure (XANES) spectroscopy. Although maximum As in the sediment porewaters varied from 8.4 to 16.2 microM, As sorption on iron oxyhydroxides at the oxic sediment-water interface prevented flux to overlying water. Floods deposit sediment containing variable amounts of arsenopyrite (FeAsS), with majorfloods depositing large amounts of sediment that bury and preserve reduced minerals. Periods of lower deposition increase sediment residence times in the oxic zone, promoting oxidation of reduced minerals, SO4(2-) efflux, and formation of oxide precipitates. Depositional events bury oxides containing sorbed As, transitioning them into anoxic environments where they undergo dissolution, releasing As to the porewater. High Fe:S ratios limit the formation of arsenic sulfides in the anoxic zone. As a result of As sequestration at the sediment-water interface and its release upon burial, decreased concentrations of porewater As will not occur unless As-bearing erosional inputs are eliminated.     

Confounding impacts of iron reduction on arsenic retention

A transition from oxidizing to reducing conditions has long been implicated to increase aqueous As concentrations, for which reductive dissolution of iron (hydr)oxides is commonly implicated as the primary culprit. Confounding our understanding of processes controlling As retention, however, is that reductive transformation of ferrihydrite has recently been shown to promote As retention rather than release. To resolve the role iron phases have in regulating arsenic concentrations, here we examine As desorption from ferrihydrite-coated sands presorbed with As(III); experiments were performed at circumneutral pH under Fe-reducing conditions with the dissimilatory iron reducing bacterium Shewanella putrefaciens strain CN-32 over extended time periods. We reveal that with the initial phase of iron reduction, ferrihydrite undergoes transformation to secondary phases and increases As(III) retention (relative to abiotic controls). However, with increased reaction time, cessation of the phase transitions and ensuing reductive dissolution result in prolonged release of As(III) to the aqueous phase. Our results suggest that As(III) retention during iron reduction is temporally dependent on secondary precipitation of iron phases; during transformation to secondary phases, particularly magnetite, As(III) retention is enhanced even relative to oxidized systems. However, conditions that retard secondary transformation (more stable iron oxides or limited iron reducing bacterial activity), or prolonged anaerobiosis, will lead to both the dissolution of ferric (hydr)oxides and release of As(III) to the aqueous phase.     

Deposition and fate of arsenic in iron- and arsenic-enriched reservoir sediments

Deposition of arsenic to the sediments of Haiwee Reservoir (Olancha, CA) has dramatically increased since March 1996 as a result of an interim strategy for arsenic management in the Los Angeles Aqueduct (LAA) water supply. Ferric chloride and cationic polymer are introduced into the Aqueduct at the Cottonwood treatment plant, 27 km north of the Haiwee Reservoir. This treatment decreases the average arsenic concentration from 25 microg/L above Cottonwood to 8.3 microg/L below Haiwee. Iron- and arsenic-rich flocculated solids are removed by deposition to the reservoir sediments. Analysis of sediments shows a pronounced signature of this deposition with elevated sediment concentrations of iron, arsenic, and manganese relative to a control site. Sediment concentrations of these elements remain elevated throughout the core length sampled (ca. 4% iron and 600 and 200 microg/g of manganese and arsenic, respectively, on a dry weight basis). A pore water profile revealed a strong redox gradient in the sediment. Manganese in the pore waters increased below 5 cm; iron and arsenic increased below 10 cm and were strongly correlated, consistent with reductive dissolution of iron oxyhydroxides and concurrent release of associated arsenic to solution. X-ray absorption near-edge spectroscopy revealed inorganic As(V) present only in the uppermost sediment (0-2.5 cm) in addition to inorganic As(III). In the deeper sediments (to 44 cm), only oxygen-coordinated As(III) was detected. Analysis of the extended X-ray absorption fine structure spectrum indicates that the As(III) at depth remains associated with iron oxyhydroxide. We hypothesize that this phase persists in the recently deposited sediment despite reducing conditions due to slow dissolution kinetics.     

Investigating arsenic speciation and mobilization in sediments with DGT and DET: a mesocosm evaluation of oxic-anoxic transitions

Mobilization of arsenic from freshwater and estuarine sediments during the transition from oxic to anoxic conditions was investigated using recently developed diffusive sampling techniques. Arsenic speciation and Fe(II) concentrations were measured at high resolution (1-3 mm) with in situ diffusive gradients in thin films (DGT) and diffusive equilibration in thin films (DET) techniques. Water column anoxia induced Fe(II) and As(III) fluxes from the sediment. A correlation between water column Fe(II) and As(III) concentrations was observed in both freshwater (r(s) = 0.896, p < 0.001) and estuarine (r(s) = 0.557, p < 0.001) mesocosms. Porewater sampling by DGT and DET techniques confirmed that arsenic mobilization was associated with the reductive dissolution of Fe(III) (hydr)oxides in the suboxic zone of the sediment; a relationship that was visible because of the ability to measure the coincident profiles of these species using combined DGT and DET samplers. The selective measurement of As(III) and total inorganic arsenic by separate DGT samplers indicated that As(III) was the primary species mobilized from the solid phase to the porewater. This measurement approach effectively ruled out substantial As(V) mobilization from the freshwater and estuarine sediments in this experiment. This study demonstrates the capabilities of the DGT and DET techniques for investigating arsenic speciation and mobilization over a range of sediment conditions.     

Spatial heterogeneity and kinetic regulation of arsenic dynamics in mangrove sediments: the sundarbans, bangladesh

The biogeochemistry of arsenic (As) in sediments is regulated by multiple factors such as particle size, dissolved organic matter (DOM), iron mobilization, and sediment binding characteristics, among others. Understanding the heterogeneity of factors affecting As deposition and the kinetics of mobilization, both horizontally and vertically, across sediment depositional environments was investigated in Sundarban mangrove ecosystems, Bengal Delta, Bangladesh. Sediment cores were collected from 3 different Sundarbans locations and As concentration down the profiles were found to be more associated with elevated Fe and Mn than with organic matter (OM). At one site chosen for field monitoring, sediment cores, pore and surface water, and in situ diffusive gradients in thin films (DGT) measurements (which were used to model As sediment pore-water concentrations and resupply from the solid phase) were sampled from four different subhabitats. Coarse-textured riverbank sediment porewaters were high in As, but with a limited resupply of As from the solid phase compared to fine-textured and high organic matter content forest floor sediments, where porewater As was low, but with much higher As resupply. Depositional environment (overbank verses forest floor) and biological activity (input of OM from forest biomass) considerably affected As dynamics over very short spatial distances in the mosaic of microhabitats that constitute a mangrove ecosystem.     

A gel probe equilibrium sampler for measuring arsenic porewater profiles and sorption gradients in sediments: II. Field application to Haiwee Reservoir sediment

Arsenic (As) geochemistry and sorption behavior were measured in As- and iron (Fe)-rich sediments of Haiwee Reservoir by deploying undoped (clear) polyacrylamide gels and hydrous ferric oxide (HFO)-doped gels in a gel probe equilibrium sampler, which is a novel technique for directly measuring the effects of porewater composition on As adsorption to Fe oxides phases in situ. Arsenic is deposited atthe sedimentsurface as As(V) and is reduced to As(III) in the upper layers of the sediment (0-8 cm), but the reduction of As(V) does not cause mobilization into the porewater. Dissolved As and Fe concentrations increased at depth in the sediment column driven by the reductive dissolution of amorphous Fe(III) oxyhydroxides and conversion to a mixed Fe(II, III) green rust-type phase. Adsorption of As and phosphorous (P) onto HFO-doped gels was inhibited at intermediate depths (10-20 cm), possibly due to dissolved organic or inorganic carbon, indicating that dissolved As concentrations were at least partially controlled by porewater composition rather than surface site availability. In sediments that had been recently exposed to air, the region of sorption inhibition was not observed, suggesting that prior exposure to air affected the extent of reductive dissolution, porewater chemistry, and As adsorption behavior. Arsenic adsorption onto the HFO-doped gels increased at depths >20 cm, and the extent of adsorption was most likely controlled by the competitive effects of dissolved phosphate. Sediment As adsorption capacity appeared to be controlled by changes in porewater composition and competitive effects at shallower depths, and by reductive dissolution and availability of sorption sites at greater burial depths.     

Arsenic redistribution between sediments and water near a highly contaminated source

Mechanisms controlling arsenic partitioning between sediment, groundwater, porewaters, and surface waters were investigated at the Vineland Chemical Company Superfund site in southern New Jersey. Extensive inorganic and organic arsenic contamination at this site (historical total arsenic > 10 000 microg L(-1) or > 130 microM in groundwater) has spread downstream to the Blackwater Branch, Maurice River, and Union Lake. Stream discharge was measured in the Blackwater Branch, and water samples and sediment cores were obtained from both the stream and the lake. Porewaters and sediments were analyzed for arsenic speciation as well as total arsenic, iron, manganese, and sulfur, and they indicate that geochemical processes controlling mobility of arsenic were different in these two locations. Arsenic partitioning in the Blackwater Branch was consistent with arsenic primarily being controlled by sulfur, whereas in Union Lake, the data were consistent with arsenic being controlled largely by iron. Stream discharge and arsenic concentrations indicate that despite large-scale groundwater extraction and treatment, > 99% of arsenic transport away from the site results from continued discharge of high arsenic groundwater to the stream, rather than remobilization of arsenic in stream sediments. Changing redox conditions would be expected to change arsenic retention on sediments. In sulfur-controlled stream sediments, more oxic conditions could oxidize arsenic-bearing sulfide minerals, thereby releasing arsenic to porewaters and streamwaters; in iron-controlled lake sediments, more reducing conditions could release arsenic from sediments via reductive dissolution of arsenic-bearing iron oxides.     

Arsenic sequestration by ferric iron plaque on cattail roots

Typha latifolia (cattail) sequesters arsenic within predominantlyferric iron root coatings, thus decreasing mobility of this toxic element in wetland sediments. Element-specific XRF microtomographic imaging illustrated a high spatial correlation between iron and arsenic in root plaques, with little arsenic in the interior of the roots. XANES analyses demonstrated that the plaque was predominantly ferric iron and contained approximately 20% As(III) and 80% As(V), which is significant because the two oxidation states form species that differ in toxicity and mobility. For the first time, spatial distribution maps of As oxidation states were developed, indicating that As(III) and As(V) are both fairly heterogeneous throughoutthe plaque. Chemical extractions showed that As was strongly adsorbed in the plaque rather than coprecipitated. Iron and arsenic concentrations ranged from 0.03 to 0.8 g Fe g(-1) wet plaque and 30 to 1200 microg As g(-1) wet plaque, consistent with a mechanism of As adsorption onto Fe(III) oxyhydroxide plaque. Because this mechanism decreases the concentrations of both As(III) and As(V) in groundwater, we propose that disruption of vegetation could increase the concentrations of mobile arsenic.     

Arsenite retention mechanisms within estuarine sediments of Pescadero, CA

Arsenic, a toxic metalloid, is commonly associated with sulfide minerals in anoxic sediments. Here we characterize arsenic(III) retention on sediments from a sulfidic estuarine marsh using a series of sorption experiments, and probe the structure of retained arsenite with X-ray absorption spectroscopy. Although the extent of sorption varied with sampling locations, several adsorption characteristics were apparent. A fraction of arsenite adsorbed over the entire pH range examined, although it was most extensive at pH greater than 7, and conformed to a Langmuir isotherm. Iron sulfide phases were responsible for As partitioning in these sediments. Initially, an FeAsS-like precipitate formed with a structure similar to those reported for As(III) sorbed on iron sulfides, a complex that is highly reactive. Following reaction for 21 d, much of the FeAsS-like precipitate was converted to As2S3. A drop in the redox potential accompanied this conversion, suggesting that the evolution of sulfide and other reduced species stabilizes bound arsenic. Processes discerned in this study reveal the importance of sulfide minerals in As sequestration within anoxic environments.     

Landfill-stimulated iron reduction and arsenic release at the Coakley Superfund Site (NH)

Arsenic is a contaminant at more than one-third of all Superfund Sites in the United States. Frequently this contamination appearsto resultfrom geochemical processes rather than the presence of a well-defined arsenic source. Here we examine the geochemical processes that regulate arsenic levels at the Coakley Landfill Superfund Site (NH), a site contaminated with As, Cr, Pb, Ni, Zn, and aromatic hydrocarbons. Long-term field observations indicate that the concentrations of most of these contaminants have diminished as a result of treatment by monitored natural attenuation begun in 1998; however, dissolved arsenic levels increased modestly over the same interval. We attribute this increase to the reductive release of arsenic associated with poorly crystalline iron hydroxides within a glaciomarine clay layer within the overburden underlying the former landfill. Anaerobic batch incubations that stimulated iron reduction in the glaciomarine clay released appreciable dissolved arsenic and iron. Field observations also suggest that iron reduction associated with biodegradation of organic waste are partly responsible for arsenic release; over the five-year study period since a cap was emplaced to prevent water flow through the site, decreases in groundwater dissolved benzene concentrations at the landfill are correlated with increases in dissolved arsenic concentrations, consistent with the microbial decomposition of both benzene and other organics, and reduction of arsenic-bearing iron oxides. Treatment of contaminated groundwater increasingly is based on stimulating natural biogeochemical processes to degrade the contaminants. These results indicate that reducing environments created within organic contaminant plumes may release arsenic. In fact, the strong correlation (>80%) between elevated arsenic levels and organic contamination in groundwater systems at Superfund Sites across the United States suggests that arsenic contamination caused by natural degradation of organic contaminants may be widespread.     

Electrochemical study of arsenate and water reduction on iron media used for arsenic removal from potable water

Zerovalent iron filings have been proposed as a filter medium for removing As(III) and As(V) compounds from potable water. The removal mechanism involves complex formation of arsenite and arsenate with the iron surface and with iron oxides produced from iron corrosion. There is conflicting evidence in the literature on whether As(V) can be reduced to As(III) by iron filter media. This research uses electrochemical methods to investigate the redox reactions that occur on the surface of zerovalent iron in arsenic solutions. The effect of arsenic on the corrosion rate of zerovalent iron was investigated by analysis of Tafel diagrams for iron wire electrodes in anaerobic solutions with As(V) concentrations between 100 and 20,000 microg/L. As(V) reduction in the absence of surface oxides was investigated by analysis of chronoamperometry profiles for iron wire electrodes in solutions with As(V) concentrations ranging from 10000 to 106 microg/L. The effect of pH on As(V) reduction was investigated by analyses of chronopotentiometry profiles for iron wire electrodes at pH values of 2, 6.5, and 11. For freely corroding iron, the presence of As(III) and As(V) decreased the iron corrosion rate by a factor of 5 as compared to that in a 3 mM CaSO4 blank electrolyte solution. The decrease in corrosion rate was independent of the arsenic concentration and was due to the blocking of cathodic sites for water reduction by arsenic compounds chemisorbed to the iron surface. The chronoamperometry and chronopotentiometry experiments showed that elevated pH and increased As(III) to As(V) ratios near the iron surface decreased the thermodynamic favorability for As(V) reduction. Therefore, reduction of As(V) occurred only at potentials that were significantly below the apparent equilibrium potentials based on bulk solution pH values and As(III) to As(V) ratios. The potentials required to reduce more than 1% of the As(V) to As(III) were below those that are obtainable in freely corroding iron media. This indicates that there will be minimal or no reduction of As(V) in iron media filters under conditions relevant to potable water treatment.     

Iron(II)-catalyzed oxidation of arsenic(III) in a sediment column

Arsenic contamination in aquatic systems is a worldwide concern. Understanding the redox cycling of arsenic in sediments is critical in evaluating the fate of arsenic in aquatic environments and in developing sediment quality guidelines. The direct oxidation of inorganic trivalent arsenic, As(III), by dissolved molecular oxygen has been studied and found to be quite slow. A chemical pathway for As(III) oxidation has been proposed recently in which a radical species, Fe(IV), produced during the oxidation of divalent iron, Fe(II), facilitates the oxidation of As(III). Rapid oxidation of As(III) was observed (on a time scale of hours) in batch systems at pH 7 and 7.5, but the extent of As(III) oxidation was limited. The Fe(II)-catalyzed oxidation of As(III) is examined in a sediment column using both computational and experimental studies. A reactive-transport model is constructed that incorporates the complex kinetics of radical species generation and Fe(II) and As(III) oxidation that have been developed previously. The model is applied to experimental column data. Results indicate that the proposed chemical pathway can explain As(III) oxidation in sediments and that transport in sediments plays a vital role in increasing the extent of As(III) oxidation and efficiency of the Fe(II) catalysis.     

Organic matter-solid phase interactions are critical for predicting arsenic release and plant uptake in Bangladesh paddy soils

Agroecological zones within Bangladesh with low levels of arsenic in groundwater and soils produce rice that is high in arsenic with respect to other producing regions of the globe. Little is known about arsenic cycling in these soils and the labile fractions relevant for plant uptake when flooded. Soil porewater dynamics of field soils (n = 39) were recreated under standardized laboratory conditions to investigate the mobility and interplay of arsenic, Fe, Si, C, and other elements, in relation to rice grain element composition, using the dynamic sampling technique diffusive gradients in thin films (DGT). Based on a simple model using only labile DGT measured arsenic and dissolved organic carbon (DOC), concentrations of arsenic in Aman (Monsoon season) rice grain were predicted reliably. DOC was the strongest determinant of arsenic solid-solution phase partitioning, while arsenic release to the soil porewater was shown to be decoupled from that of Fe. This study demonstrates the dual importance of organic matter (OM), in terms of enhancing arsenic release from soils, while reducing bioavailability by sequestering arsenic in solution.     

Arsenic removal with iron(II) and iron(III) in waters with high silicate and phosphate concentrations

Arsenic removal by passive treatment, in which naturally present Fe(II) is oxidized by aeration and the forming iron(III) (hydr)oxides precipitate with adsorbed arsenic, is the simplest conceivable water treatment option. However, competing anions and low iron concentrations often require additional iron. Application of Fe(II) instead of the usually applied Fe(III) is shown to be advantageous, as oxidation of Fe(II) by dissolved oxygen causes partial oxidation of As(III) and iron(III) (hydr)oxides formed from Fe(II) have higher sorption capacities. In simulated groundwater (8.2 mM HCO3(-), 2.5 mM Ca2+, 1.6 mM Mg2+, 30 mg/L Si, 3 mg/L P, 500 ppb As(III), or As(V), pH 7.0 +/- 0.1), addition of Fe(II) clearly leads to better As removal than Fe(III). Multiple additions of Fe(II) further improved the removal of As(II). A competitive coprecipitation model that considers As(III) oxidation explains the observed results and allows the estimation of arsenic removal under different conditions. Lowering 500 microg/L As(III) to below 50 microg/L As(tot) in filtered water required > 80 mg/L Fe(III), 50-55 mg/L Fe(II) in one single addition, and 20-25 mg/L in multiple additions. With As(V), 10-12 mg/L Fe(II) and 15-18 mg/L Fe(III) was required. In the absence of Si and P, removal efficiencies for Fe(II) and Fe(III) were similar: 30-40 mg/L was required for As(II), and 2.0-2.5 mg/L was required for As(V). In a field study with 22 tubewells in Bangladesh, passive treatment efficiently removed phosphate, but iron contents were generally too low for efficient arsenic removal.     

Compost-based permeable reactive barriers for the source treatment of arsenic contaminations in aquifers: column studies and solid-phase investigations

The bulk of arsenic (As) at contaminated sites is frequently associated with iron (hydr)oxides. Various studies ascribe increasing dissolved As concentrations to the transformation of iron (hydr)oxides into iron sulfides, which is initiated by dissolved sulfide. We investigated whetherthis processes can be utilized as a source treatment approach using compost-based permeable reactive barriers (PRB), which promote microbial sulfate reduction. Arsenic-bearing aquifer sedimentfrom a contaminated industrial site showed a decrease in As content of <10% after 420 days of percolation with sulfide-free artificial groundwater. In contrast, water that had previously passed through organic matter and exhibited sulfide concentrations of 10-30 mg/L decreased As content in the sediment by 87% within 360 days. X-ray diffraction showed no arsenic sulfides, but XANES spectra (X-ray absorption near edge structure) and associated linear combinations revealed that adsorbed arsenate of the original sediment was in part reduced to arsenite and indicated the formation of minor amounts of a substance that contains As and sulfur. The speciation of dissolved As changed from initially As(V)-dominated to As(III)-dominated after sulfide flushing was started, which increases the mobility of As. Because sulfide can be supplied not only by compost-based PRBs but also by direct injection, sulfide flushing has a wide range of application for the source treatment of arsenic.     

Real-time X-ray absorption spectroscopy of uranium, iron, and manganese in contaminated sediments during bioreduction

The oxidation status of uranium in sediments is important because the solubility of this toxic and radioactive element is much greater for U(VI) than for U(IV) species. Thus, redox manipulation to promote precipitation of UO2 is receiving interest as a method to remediate U-contaminated sediments. Presence of Fe and Mn oxides in sediments at much higher concentrations than U requires an understanding of their redox status as well. This study was conducted to determine changes in oxidation states of U, Fe, and Mn in U-contaminated sediments from Oak Ridge National Laboratory. Oxidation states of these elements were measured in real-time and nondestructively using X-ray absorption spectroscopy on sediment columns supplied with synthetic groundwater containing organic carbon (OC, 0, 3, 10, 30, and 100 mM OC as lactate) for over 400 days. In sediments supplied with OC > or = 30 mM, 80% of the U was reduced to U(IV), with transient reoxidation at about 150 days. Mn(III,IV) oxides were completely reduced to Mn(II) in sediments infused with OC > or = 3 mM. However, Fe remained largely unreduced in all sediment columns, showing that Fe(III) can persist as an electron acceptor in reducing sediments over long times. This result in combination with the complete reduction of all other potential electron acceptors supports the hypothesis that the reactive Fe(III) fraction was responsible for reoxidizing U(IV).     

Arsenic(III) and arsenic(V) reactions with zerovalent iron corrosion products

Zerovalent iron (Fe0) has tremendous potential as a remediation material for removal of arsenic from groundwater and drinking water. This study investigates the speciation of arsenate (As(V)) and arsenite (As(III)) after reaction with two Fe0 materials, their iron oxide corrosion products, and several model iron oxides. A variety of analytical techniques were used to study the reaction products including HPLC-hydride generation atomic absorption spectrometry, X-ray diffraction, scanning electron microscopy-energy-dispersive X-ray analysis, and X-ray absorption spectroscopy. The products of corrosion of Fe0 include lepidocrocite (gamma-FeOOH), magnetite (Fe3O4), and/or maghemite (gamma-Fe2O3), all of which indicate Fe(II) oxidation as an intermediate step in the Fe0 corrosion process. The in-situ Fe0 corrosion reaction caused a high As(III) and As(V) uptake with both Fe0 materials studied. Under aerobic conditions, the Fe0 corrosion reaction did not cause As(V) reduction to As(III) but did cause As(III) oxidation to As(V). Oxidation of As(III) was also caused by maghemite and hematite minerals indicating that the formation of certain iron oxides during Fe0 corrosion favors the As(V) species. Water reduction and the release of OH- to solution on the surface of corroding Fe0 may also promote As(III) oxidation. Analysis of As(III) and As(V) adsorption complexes in the Fe0 corrosion products and synthetic iron oxides by extended X-ray absorption fine structure spectroscopy (EXAFS) gave predominant As-Fe interatomic distances of 3.30-3.36 A. This was attributed to inner-sphere, bidentate As(III) and As(V) complexes. The results of this study suggest that Fe0 can be used as a versatile and economical sorbent for in-situ treatment of groundwater containing As(III) and As(V).     

Comparison of arsenic(V) and arsenic(III) sorption onto iron oxide minerals: implications for arsenic mobility

Arsenic derived from natural sources occurs in groundwater in many countries, affecting the health of millions of people. The combined effects of As(V) reduction and diagenesis of iron oxide minerals on arsenic mobility are investigated in this study by comparing As(V) and As(III) sorption onto amorphous iron oxide (HFO), goethite, and magnetite at varying solution compositions. Experimental data are modeled with a diffuse double layer surface complexation model, and the extracted model parameters are used to examine the consistency of our results with those previously reported. Sorption of As(V) onto HFO and goethite is more favorable than that of As(III) below pH 5-6, whereas, above pH 7-8, As(II) has a higher affinity for the solids. The pH at which As(V) and As(III) are equally sorbed depends on the solid-to-solution ratio and type and specific surface area of the minerals and is shifted to lower pH values in the presence of phosphate, which competes for sorption sites. The sorption data indicate that, under most of the chemical conditions investigated in this study, reduction of As(V) in the presence of HFO or goethite would have only minor effects on or even decrease its mobility in the environment at near-neutral pH conditions. As(V) and As(III) sorption isotherms indicate similar surface site densities on the three oxides. Intrinsic surface complexation constants for As(V) are higher for goethite than HFO, whereas As(III) binding is similar for both of these oxides and also for magnetite. However, decrease in specific surface area and hence sorption site density that accompanies transformation of amorphous iron oxides to more crystalline phases could increase arsenic mobility.     

Arsenate and arsenite adsorption and desorption behavior on coprecipitated aluminum:iron hydroxides

Although arsenic adsorption/desorption behavior on aluminum and iron (oxyhydr)oxides has been extensively studied, little is known about arsenic adsorption/desorption behavior by bimetal Al:Fe hydroxides. In this study, influence of the Al:Fe molar ratio, pH, and counterion (Ca2+ versus Na+) on arsenic adsorption/desorption by preformed coprecipitated Al:Fe hydroxides was investigated. Adsorbents were formed by initial hydrolysis of mixed Al3+/ Fe3+ salts to form coprecipitated Al:Fe hydroxide products. At Al:Fe molar ratios < or = 1:4, Al3+ was largely incorporated into the iron hydroxide structure to form a poorly crystalline bimetal hydroxide; however, at higher Al:Fe molar ratios, crystalline aluminum hydroxides (bayerite and gibbsite) were formed. Although approximately equal As(V) adsorption maxima were observed for 0:1 and 1:4 Al:Fe hydroxides, the As(III) adsorption maximum was greater with the 0:1 Al: Fe hydroxide. As(V) and As(III) adsorption decreased with further increases in Al:Fe molar ratio. As(V) exhibited strong affinity to 0:1 and 1:4 Al:Fe hydroxides at pH 3-6. Adsorption decreased at pH > 6.5; however, the presence of Ca2+ compared to Na+ as the counterion enhanced As( retention by both hydroxides. There was more As(V) and especially As(III) desorption by phosphate with an increase in Al:Fe molar ratio.     

Removal of arsenic from synthetic acid mine drainage by electrochemical pH adjustment and coprecipitation with iron hydroxide

Acid mine drainage (AMD), which is caused by the biological oxidation of sulfidic materials, frequently contains arsenic in the form of arsenite, As(III), and/or arsenate, As(V), along with much higher concentrations of dissolved iron. The present work is directed toward the removal of arsenic from synthetic AMD by raising the pH of the solution by electrochemical reduction of H+ to elemental hydrogen and coprecipitation of arsenic with iron(III) hydroxide, following aeration of the catholyte. Electrolysis was carried out at constant current using two-compartment cells separated with a cation exchange membrane. Four different AMD model systems were studied: Fe(III)/As(V), Fe(III)/As(III), Fe(II)/As(V), and Fe(II)/As(III) with the initial concentrations for Fe(III) 260 mg/L, Fe(II) 300 mg/L, As(V), and As(III) 8 mg/L. Essentially quantitative removal of arsenic and iron was achieved in all four systems, and the results were independent of whether the pH was adjusted electrochemically or by the addition of NaOH. Current efficiencies were approximately 85% when the pH of the effluent was 4-7. Residual concentrations of arsenic were close to the drinking water standard proposed by the World Health Organization (10 microg/L), far below the mine waste effluent standard (500 microg/L).