Selective catalytic reduction of NO by C3H8 over CoOx/Al2O3: An investigation of structure–activity relationships

A series of CoO_x/Al₂O₃ catalysts was prepared, characterized, and applied for the selective catalytic reduction (SCR) of NO by C₃H₈. The results of XRD, UV–vis, IR, Far-IR and ESR characterizations of the catalysts suggest that the predominant oxidation state of cobalt species is +2 for the catalysts with low cobalt loading (≤2 mol%) and for the catalysts with 4 mol% cobalt loading prepared by sol–gel and co-precipitation. Co₃O₄ crystallites or agglomerates are the predominant species in the catalysts with high cobalt loading prepared by incipient wetness impregnation and solid dispersion. An optimized CoO_x/Al₂O₃ catalyst shows high activity in SCR of NO by C₃H₈ (100% conversion of NO at 723 K, GHSV: 10,000 h⁻¹). The activity of the selective catalytic reduction of NO by C₃H₈ increases with the increase of cobalt–alumina interactions in the catalysts. The influences of cobalt loading and catalyst preparation method on the catalytic performance suggest that tiny CoAl₂O₄ crystallites highly dispersed on alumina are responsible for the efficient catalytic reduction of NO, whereas Co₃O₄ crystallites catalyze the combustion of C₃H₈ only.     

NO reduction by CH4 in the presence of O2 over La2O3 supported on Al2O3

Dispersing La₂O₃ on δ- or γ-Al₂O₃ significantly enhances the rate of NO reduction by CH₄ in 1% O₂, compared to unsupported La₂O₃. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La₂O₃ precursor used, the pretreatment, and the La₂O₃ loading. The most active family of catalysts consisted of La₂O₃ on γ-Al₂O₃ prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m²) occurred between the addition of one and two theoretical monolayers of La₂O₃ on the γ-Al₂O₃ surface. The best catalyst, 40% La₂O₃/γ-Al₂O₃, had a turnover frequency at 700°C of 0.05 s⁻¹, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La₂O₃/Al₂O₃ catalysts exhibited stable activity under high conversion conditions as well as high CH₄ selectivity (CH₄ + NO vs. CH₄ + O₂). The addition of Sr to a 20% La₂O₃/γ-Al₂O₃ sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO⁼₄ to the latter Sr-promoted La₂O₃/Al₂O₃ catalyst decreased activity although sulfate increased the activity of Sr-promoted La₂O₃. Dispersing La₂O₃ on SiO₂ produced catalysts with extremely low specific activities, and rates were even lower than with pure La₂O₃. This is presumably due to water sensitivity and silicate formation. The La₂O₃/Al₂O₃ catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications.     

Oxidative degradation properties of Co-based catalysts in the presence of ozone

Four series of cobalt-based catalysts, such as bare Co₃O₄ and CoO, CoO_x–CeO₂ mixed oxides, CoO_x supported over alumina and alumina–baria and CoMgAl and CoNiAl hydrotalcites have been synthesized and investigated for the oxidative degradation of phenol in the presence of ozone. Characterizations were obtained by several techniques in order to investigate the nature of cobalt species and their morphological properties, depending on the system. Analyses by XRD, BET, TPR, UV–visible diffuse reflectance spectroscopy and TG/DT were performed.

The CoNiAl hydrotalcite exhibits, after 4 h of reaction, the highest phenol ozonation activity followed by Co(3 wt%)/Al₂O₃–BaO and CoMgAl. The samples Co(1 wt%)/Al₂O₃–BaO and Co(1 and 3 wt%)/Al₂O₃ show a comparable medium activity, while the oxidation properties of bare oxides Co₃O₄, CoO and CoO_x–CeO₂ are really low. Leaching of cobalt ions in the water solution was detected during the reaction, the amount varied depending on the nature of catalysts. A massive release was observed for the CoMgAl and CoNiAl hydrotalcites, while cobalt catalysts over alumina and alumina–baria look much more stable. The recycle of CoO_x/Al₂O₃ and CoO_x/Al₂O₃–BaO was studied by performing three consecutive cycles in the phenol oxidation. Because of the potential interest of the cobalt-supported catalysts in the ozonation process, the oxidative degradation of naphtol blue black was also investigated.

On the basis of TPR and UV–visible results it appears that highly dispersed Co²⁺ ions especially present over Co(3 wt%)/Al₂O₃–BaO are the main active sites for phenol and naphtol blue black oxidative degradation by ozone.     

η-Al2O3与γ-Al2O3在CS2催化水解反应中的性能比较

通过制备高纯度的前驱体湃铝石获得了η-Al₂O₃材料,采用XRD验证了η-Al₂O₃与γ-Al₂O₃在晶相结构上的差异,比较了两者的表面形貌、织构及酸碱性能,结果显示,η-Al₂O₃与γ-Al₂O₃的比表面积相当,但η-Al₂O₃具有更弱的弱碱位和较少的强碱位,并拥有丰富的中等强度酸性位。将η-Al₂O₃与γ-Al₂O₃作为催化剂应用于CS₂水解反应,结果表明,在(200~450) ℃测试温度范围内,η-Al₂O₃催化剂对CS₂的水解活性始终优于γ-Al₂O₃,两种催化剂上CS₂反应的浓度效应也明显不同,推测与它们的酸碱性质影响了对CS₂的吸附能力有关,导致两者催化CS₂水解反应遵循了不同的机制。     

Partial oxidation of methane to synthesis gas over Co/Ca/Al2O3 catalysts

A series of calcium-modified alumina-supported cobalt catalysts were prepared with a two-step impregnation method, and the effect of calcium on the catalytic performances of the catalysts for the partial oxidation of methane to syngas (CO and H₂) was investigated at 750 °C. Also, the catalysts were characterized by XRD, TEM, TPR and (in situ) Raman. At 6 wt.% of cobalt loading, the unmodified alumina-supported cobalt catalyst showed a very low activity and a rapid deactivation, while the calcium-modified catalyst presented a good performance for this process with the CH₄ conversion of 88%, CO selectivity of 94% and undetectable carbon deposition during a long-time running. Characterization results showed that the calcium modification can effectively increase the dispersion and reducibility of Co₃O₄, decrease the Co metal particle size, and suppress the reoxidation of cobalt as well as the phase transformation to form CoAl₂O₄ spinel phases under the reaction conditions. These could be related to the excellent catalytic performances of Co/Ca/Al₂O₃ catalysts.     

Role of CeO2 in Ni/CeO2–Al2O3 catalysts for carbon dioxide reforming of methane

Ni catalysts supported on γ-Al₂O₃, CeO₂ and CeO₂–Al₂O₃ systems were tested for catalytic CO₂ reforming of methane into synthesis gas. Ni/CeO₂–Al₂O₃ catalysts showed much better catalytic performance than either CeO₂- or γ-Al₂O₃-supported Ni catalysts. CeO₂ as a support for Ni catalysts produced a strong metal–support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO₂ had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/γ-Al₂O₃ catalysts for this reaction. A weight loading of 1–5 wt% CeO₂ was found to be the optimum. Ni catalysts with CeO₂ promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO₂-promoted catalysts are attributed to the oxidative properties of CeO₂.     

Ce1−xCuxO2−x/Al2O3/FeCrAl catalysts for catalytic combustion of methane

A series of the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts (x = 0–1) were prepared. The structure of the catalysts was characterized using XRD, SEM and H₂-TPR. The catalytic activity of the catalysts for the combustion of methane was evaluated. The results indicated that in the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts the surface phase structure were the Ce_1−xCu_xO_2−x solid solution, -Al₂O₃ and γ-Al₂O₃. The surface particle shape and size were different with the variety of the molar ratio of Ce to Cu in the Ce_1−xCu_xO_2−x solid solution. The Cu component of the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts played an important role to the catalytic activity for the methane combustion. There were the stronger interaction among the Ce_1−xCu_xO_2−x solid solution and the Al₂O₃ washcoats and the FeCrAl support.     

Carbon formation and its influence on ethanol steam reforming over Ni/Al2O3 catalysts

Ethanol steam reforming was studied over Ni/Al₂O₃ catalysts. The effect of support (- and γ-Al₂O₃), metal loading and a comparison between conventional H₂ reduction with an activation method employing a CH₄/O₂ mixture was investigated. The properties of catalysts were studied by N₂ physisorption, X-ray diffraction (XRD) and temperature programmed reduction (TPR). After activity tests, the catalysts were analyzed by scanning electron microscopy (SEM) and thermogravimetric analysis (TG/DTA). Ni supported on γ-Al₂O₃ was more active for H₂ production than the catalyst supported on -Al₂O₃. Metal loading did not affect the catalytic performance. The alternative activation method with CH₄/O₂ mixture affected differently the activity and stability of the Ni/γ-Al₂O₃ and the Ni/-Al₂O₃ catalyst. This activation method increased significantly the stability of Ni/-Al₂O₃ compared to H₂ reduction. SEM and TG/DTA analysis indicate the formation of filamentous carbon during the CH₄/O₂ activation step, which is associated with the increasing catalyst activity and stability. The effect of temperature on the type of carbon formed was investigated; indicating that filamentous coke increased activity while encapsulating coke promoted deactivation. A discussion about carbon formation and the influence on the activity is presented.     

Hydrodesulfurization over supported monometallic, bimetallic and promoted carbide and nitride catalysts

The preparation of alumina-supported β-Mo₂C, MoC_1−x (x≈0.5), γ-Mo₂N, Co–Mo₂C, Ni₂Mo₃N, Co₃Mo₃N and Co₃Mo₃C catalysts is described and their hydrodesulfurization (HDS) catalytic properties are compared to conventional sulfide catalysts having similar metal loadings. Alumina-supported β-Mo₂C and γ-Mo₂N catalysts (Mo₂C/Al₂O₃ and Mo₂N/Al₂O₃, respectively) are significantly more active than sulfided MoO₃/Al₂O₃ catalysts, and X-ray diffraction, pulsed chemisorption and flow reactor studies of the Mo₂C/Al₂O₃ catalysts indicate that they exhibit strong resistance to deep sulfidation. A model is presented for the active surface of Mo₂C/Al₂O₃ and Mo₂N/Al₂O₃ catalysts in which a thin layer of sulfided Mo exposing a high density of sites forms at the surface of the alumina-supported β-Mo₂C and γ-Mo₂N particles under HDS conditions. Cobalt promoted catalysts, Co–Mo₂C/Al₂O₃, have been found to be substantially more active than conventional sulfided Co–MoO₃/Al₂O₃ catalysts, while requiring less Co to achieve optimal HDS activity than is observed for the sulfide catalysts. Alumina-supported bimetallic nitride and carbide catalysts (Ni₂Mo₃N/Al₂O₃, Co₃Mo₃N/Al₂O₃, Co₃Mo₃C/Al₂O₃), while significantly more active for thiophene HDS than unpromoted Mo nitride and carbide catalysts, are less active than conventional sulfided Ni–Mo and Co–Mo catalysts prepared from the same oxidic precursors.     

Total oxidation of propene and propane over gold–copper oxide on alumina catalysts: Comparison with Pt/Al2O3

Oxidation of propene and propane to CO₂ and H₂O has been studied over Au/Al₂O₃ and two different Au/CuO/Al₂O₃ (4 wt.% Au and 7.4 wt.% Au) catalysts and compared with the catalytic behaviour of Au/Co₃O₄/Al₂O₃ (4.1 wt.% Au) and Pt/Al₂O₃ (4.8 wt.% Pt) catalysts. The various characterization techniques employed (XRD, HRTEM, TPR and DR-UV–vis) revealed the presence of metallic gold, along with a highly dispersed CuO (6 wt.% CuO), or more crystalline CuO phase (12 wt.% CuO).

A higher CuO loading does not significantly influence the catalytic performance of the catalyst in propene oxidation, the gold loading appears to be more important. Moreover, it was found that 7.4Au/CuO/Al₂O₃ is almost as active as Pt/Al₂O₃, whereas Au/Co₃O₄/Al₂O₃ performs less than any of the CuO-containing gold-based catalysts.

The light-off temperature for C₃H₈ oxidation is significantly higher than for C₃H₆. For this reaction the particle size effect appears to prevail over the effect of gold loading. The most active catalysts are 4Au/CuO/Al₂O₃ (gold particles less than 3 nm) and 4Au/Co₃O₄/Al₂O₃ (gold particles less than 5 nm).     

Performance and characterization of Ru/Al2O3 and Ru/SiO2 catalysts modified with Mn for Fischer–Tropsch synthesis

Mn effect and characterization on γ-Al₂O₃-, -Al₂O₃- and SiO₂-supported Ru catalysts were investigated for Fischer–Tropsch synthesis under pressurized conditions. In the slurry phase Fischer–Tropsch reaction, γ-Al₂O₃ catalysts showed higher performance on CO conversion and C₅⁺ selectivity than -Al₂O₃ and SiO₂ catalysts. Moreover, Ru/Mn/γ-Al₂O₃ exhibited high resistance to catalyst deactivation and other catalysts were deactivated during the reaction. From characterization results on XRD, TPR, TEM, XPS and pore distribution, Ru particles were clearly observed over the catalysts, and γ-Al₂O₃ catalysts showed a moderate pore and particle size such as 8 nm, where -Al₂O₃ and SiO₂ showed highly dispersed ruthenium particles. The addition of Mn to γ-Al₂O₃ enhanced the removal of chloride from RuCl₃, which can lead to the formation of metallic Ru with moderate particle size, which would be an active site for Fischer–Tropsch reaction. Concomitantly, manganese chloride is formed. These schemes can be assigned to the stable nature of Ru/Mn/γ-Al₂O₃ catalyst.     

The effect of CeO2 structure on the activity of supported Pd catalysts used for methane steam reforming

Palladium (Pd) supported on CeO₂-promoted γ-Al₂O₃ with various CeO₂ (ceria) crystallinities, were used as catalysts in the methane steam reforming reaction. X-ray diffraction (XRD) analysis, FTIR spectroscopy of adsorbed CO, and X-ray photoelectron spectroscopy (XPS) were employed to characterize the samples in terms of Pd and CeO₂ structure and dispersion on the γ-Al₂O₃ support. These results were correlated with the observed catalytic activity and deactivation process. Arrhenius plots at steady-state conditions are presented as a function of CeO₂ structure. Pd is present on the oxidized CeO₂-promoted catalysts as Pd⁰, Pd⁺ and Pd²⁺, at ratios strongly dependent on CeO₂ structure. XRD measurements indicated that Pd is well dispersed (particles <2 nm) on crystalline CeO₂ and is agglomerated as large clusters (particles in 10–20 nm range) on amorphous CeO₂. FTIR spectra of adsorbed CO revealed that after pre-treatment under H₂ or in the presence of amorphous CeO₂, partial encapsulation of Pd particles occurs. CeO₂ structure influences the CH₄ steam reforming reaction rates. Crystalline CeO₂ and dispersed Pd favor high reaction rates (low activation energy). The presence of CeO₂ as a promoter conferred high catalytic activity to the alumina-supported Pd catalysts. The catalytic activity is significantly lower on Pd/γ-Al₂O₃ or on amorphous (reduced) CeO₂/Al₂O₃ catalysts. The reaction rates are two orders of magnitude higher on Pd/CeO₂/γ-Al₂O₃ than on Pd/γ-Al₂O₃, which is attributed to a catalytic synergism between Pd and CeO₂. The low rates on the reduced Pd/CeO₂/Al₂O₃ catalysts can be correlated with the loss of Pd sites through encapsulation or particle agglomeration, a process found mostly irreversible after catalyst regeneration.     

Catalytic performance of Co3O4/CeO2 and Co3O4/CeO2–ZrO2 composite oxides for methane combustion: Influence of catalyst pretreatment temperature and oxygen concentration in the reaction mixture

The influence of catalyst pre-treatment temperature (650 and 750 °C) and oxygen concentration (λ = 8 and 1) on the light-off temperature of methane combustion has been investigated over two composite oxides, Co₃O₄/CeO₂ and Co₃O₄/CeO₂–ZrO₂ containing 30 wt.% of Co₃O₄. The catalytic materials prepared by the co-precipitation method were calcined at 650 °C for 5 h (fresh samples); a portion of them was further treated at 750 °C for 7 h, in a furnace in static air (aged samples).

Tests of methane combustion were carried out on fresh and aged catalysts at two different WHSV values (12 000 and 60 000 mL g⁻¹ h⁻¹). The catalytic performance of Co₃O₄/CeO₂ and Co₃O₄/CeO₂–ZrO₂ were compared with those of two pure Co₃O₄ oxides, a sample obtained by the precipitation method and a commercial reference. Characterization studies by X-ray diffraction (XRD), BET and temperature-programmed reduction (TPR) show that the catalytic activity is related to the dispersion of crystalline phases, Co₃O₄/CeO₂ and Co₃O₄/CeO₂–ZrO₂ as well as to their reducibility. Particular attention was paid to the thermal stability of the Co₃O₄ phase in the temperature range of 750–800 °C, in both static (in a furnace) and dynamic conditions (continuous flow). The results indicate that the thermal stability of the phase Co₃O₄ heated up to 800 °C depends on the size of the cobalt oxide crystallites (fresh or aged samples) and on the oxygen content (excess λ = 8, stoichiometric λ = 1) in the reaction mixture. A stabilizing effect due to the presence of ceria or ceria–zirconia against Co₃O₄ decomposition into CoO was observed.

Moreover, the role of ceria and ceria–zirconia is to maintain a good combustion activity of the cobalt composite oxides by dispersing the active phase Co₃O₄ and by promoting the reduction at low temperature.     

Ozonation of alachlor catalyzed by Cu/Al2O3 in water

The Cu/Al₂O₃ catalyzed ozonation for degrading an endocrine disruptor—alachlor in water was investigated. The Cu/Al₂O₃ powders were coated on a cordierite honeycomb column, which was taken as the reactor of catalytic ozonation of alachlor. Additional uncatalyzed experiments were carried out and the results were compared to those of the catalytic runs.

The experimental results demonstrated that Cu/Al₂O₃ was a very effective catalyst for ozonation of alachlor. The removal rate of alachlor in total organic carbon (TOC) with ozonation in the absence of Cu/Al₂O₃ was only above 20% in 180 min, while the reduction of totle organic carbon (TOC) in the presence of Cu/Al₂O₃ was more than 60%. Correspondingly, more inorganic ions created and less by-products produced in the Cu/Al₂O₃ catalyzed ozonation than in the unanalyzed process. These results indicated that the use of Cu/Al₂O₃ substantially enhanced the mineralization of alachlor in ozonation. The EPR experiments verified that more √OH radicals generated in the Cu/Al₂O₃ catalyzed ozonation could bring on a higher alachlor removal rate.     

Effect of phosphorus addition on the hydrotreating activity of NiMo/Al2O3 carbide catalyst

A series of phosphorus promoted γ-Al₂O₃ supported NiMo carbide catalysts with 0–4.5 wt.% P, 13 wt.% Mo and 2.5 wt.% Ni were synthesized and characterized by elemental analysis, pulsed CO chemisorption, BET surface area measurement, X-ray diffraction, near-edge X-ray absorption fine structure, DRIFT spectroscopy of CO adsorption and H₂ temperature programmed reduction. X-ray diffraction patterns and CO uptake showed the P addition to NiMo/γ-Al₂O₃ carbide, increased the dispersion of β-Mo₂C particles. DRIFT spectra of adsorbed CO revealed that P addition to NiMo/γ-Al₂O₃ carbide catalyst not only increases the dispersion of Ni-Mo carbide phase, but also changes the nature of surface active sites. The hydrodenitrogenation (HDN) and hydrodesulfurization (HDS) activities of these P promoted NiMo/γ-Al₂O₃ carbide catalysts were performed in trickle bed reactor using light gas oil (LGO) derived from Athabasca bitumen and model feed containing quinoline and dibenzothiophene at industrial conditions. The P added NiMo/γ-Al₂O₃ carbide catalysts showed enhanced HDN activity compared to the NiMo/γ-Al₂O₃ catalysts with both the feed stocks. The P had almost no influence on the HDS activity of NiMo/γ-Al₂O₃ carbide with LGO and dibenzothiophene. P addition to NiMo/γ-Al₂O₃ carbide accelerated CN bond breaking and thus increased the HDN activity.     

Interactions NO—CO and O2—NO—CO on CuCo2O4/γ-Al2O3 and on γ-Al2O3- and CuCo2O4/γ-Al2O3-supported Pt, Rh and Pt—Rh catalysts, a transient response study

The interactions NO—CO and O₂—NO—CO have been studied onCuCo₂O₄γ-Al₂O₃ and on γ-Al₂O₃- and CuCo₂O₄γ-Al₂O₃-supported Pt, Rh and Pt—Rh catalysts. The deposition of noble metals (Pt, Rh and Pt—Rh) on CuCo₂O₄γ-Al₂O₃ instead of γ-Al₂O₃ is beneficial in: lowering the temperature at which maximum N₂O is formed and decreasing the maximum N₂O concentration attained; lowering the onset temperature of NO to N₂ reduction, and increasing the N₂ selectivity; preserving the activity towards NO to N₂ reduction on a higher level following the concentration step NO + COO₂+ NO + CO and changing the conditions from stoichiometric to oxidizing (50% excess of oxidants). The reason for this behaviour of the CuCo₂O₄γ-Al₂O₃-based noble metal catalysts is the formation (reversible) of a reduced surface layer on the CuCo₂O₄ supported spinel under the conditions of a stoichiometric NO + CO mixture.     

Surface properties and reactivity of Cu/γ-Al2O3 catalysts for NO reduction by C3H6: Influences of calcination temperatures and additives

The influences of calcination temperatures and additives for 10 wt.% Cu/γ-Al₂O₃ catalysts on the surface properties and reactivity for NO reduction by C₃H₆ in the presence of excess oxygen were investigated. The results of XRD and XPS show that the 10 wt.% Cu/γ-Al₂O₃ catalysts calcined below 973 K possess highly dispersed surface and bulk CuO phases. The 10 wt.% Cu/γ-Al₂O₃ and 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalysts calcined at 1073 K possess a CuAl₂O₄ phase with a spinel-type structure. In addition, the 10 wt.% La–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses a bulk CuO phase. The result of NO reduction by C₃H₆ shows that the CuAl₂O₄ is a more active phase than the highly dispersed and bulk CuO phase. However, the 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses significantly lower reactivity for NO reduction than the 10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K, although these catalysts possess the same CuAl₂O₄ phase. The low reactivity for NO reduction for 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K is attributed to the formation of less active CuAl₂O₄ phase with high aggregation and preferential promotion of C₃H₆ combustion to CO_x by MnO₂. The engine dynamometer test for NO reduction shows that the C₃H₆ is a more effective reducing agent for NO reduction than the C₂H₅OH. The maximum reactivity for NO reduction by C₃H₆ is reached when the NO/C₃H₆ ratio is one.     

负载型Pt-Fe/Al2O3催化剂用于室温催化氧化甲醛

采用胶体沉积法制备不同载体（Ni₂O₃、Co₃O₄、TiO₂、Al₂O₃）的Pt-Fe/MeO_x催化剂用于甲醛室温催化氧化。活性测试表明,以γ-Al₂O₃为载体的Pt-Fe/Al₂O₃催化剂具有较高的催化活性,在25℃时甲醛的转化率可达到100%,而且Pt-Fe/ Al₂O₃催化剂还表现出良好的稳定性。采用各种表征技术对Pt-Fe/Al₂O₃的形貌、价态及氧化还原性等物理化学性质进行了研究,结果表明：Pt-Fe/Al₂O₃催化剂中Pt物种和Fe物种在Al₂O₃载体的表面上均匀分散;二者之间存在着较强的相互作用,在Al₂O₃载体的表面上形成一些类似Pt-O-Fe活性物种,有效促进了Pt-Fe/Al₂O₃催化性能,从而显示出较高的氧化活性。     

Lean reduction of NO by C3H6 over Ag/alumina derived from Al2O3, AlOOH and Al(OH)3

The effectiveness of Ag/Al₂O₃ catalyst depends greatly on the alumina source used for preparation. A series of alumina-supported catalysts derived from AlOOH, Al₂O₃, and Al(OH)₃ was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet–visible (UV–vis) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, O₂, NO + O₂-temperature programmed desorption (TPD), H₂-temperature programmed reduction (TPR), thermal gravimetric analysis (TGA) and activity test, with a focus on the correlation between their redox properties and catalytic behavior towards C₃H₆-selective catalytic reduction (SCR) of NO reaction. The best SCR activity along with a moderated C₃H₆ conversion was achieved over Ag/Al₂O₃ (I) employing AlOOH source. The high density of Ag–O–Al species in Ag/Al₂O₃ (I) is deemed to be crucial for NO selective reduction into N₂. By contrast, a high C₃H₆ conversion simultaneously with a moderate N₂ yield was observed over Ag/Al₂O₃ (II) prepared from a γ-Al₂O₃ source. The larger particles of Ag_mO (m > 2) crystallites were believed to facilitate the propene oxidation therefore leading to a scarcity of reductant for SCR of NO. An amorphous Ag/Al₂O₃ (III) was obtained via employing a Al(OH)₃ source and 500 °C calcination exhibiting a poor SCR performance similar to that for Ag-free Al₂O₃ (I). A subsequent calcination of Ag/Al₂O₃ (III) at 800 °C led to the generation of Ag/Al₂O₃ (IV) catalyst yielding a significant enhancement in both N₂ yield and C₃H₆ conversion, which was attributed to the appearance of γ-phase structure and an increase in surface area. Further thermo treatment at 950 °C for the preparation of Ag/Al₂O₃ (V) accelerated the sintering of Ag clusters resulting in a severe unselective combustion, which competes with SCR of NO reaction. In view of the transient studies, the redox properties of the prepared catalysts were investigated showing an oxidation capability of Ag/Al₂O₃ (II and V) > Ag/Al₂O₃ (IV) > Ag/Al₂O₃ (I) > Ag/Al₂O₃ (III) and Al₂O₃ (I). The formation of nitrate species is an important step for the deNO_x process, which can be promoted by increasing O₂ feed concentration as evidenced by NO + O₂-TPD study for Ag/Al₂O₃ (I), achieving a better catalytic performance.     

Pt/Pt-Ce/γ-Al2O3催化氧化甲苯研究

通过等体积浸渍法制备单贵金属Pt/γ-Al₂O₃和双金属Pt-Ce/γ-Al₂O₃催化剂,考察Ce对催化剂活性的影响,确定催化剂最优配比。结果表明,当Pt的负载量为质量分数0.5%时,Pt/γ-Al₂O₃催化活性最高;当Pt的负载量为质量分数0.2%,Ce的负载量为质量分数1.0%时,Pt-Ce/γ-Al₂O₃催化剂的催化活性最高。Pt-Ce/γ-Al₂O₃催化剂的甲苯转化率高于Pt/γ-Al₂O₃催化剂。随着Pt负载量增大,催化剂孔容、孔径减小。粉体式催化剂性能优于整体式催化剂,但差别不大;Ce的添加有助于催化剂活性的提升。