Effect of filler surface treatment on mechanical properties and thermal properties of single and hybrid filler–filled PP composites

The influence of two types of surface treatments (aminosilane and Lica‐12) on the mechanical and thermal properties of polypropylene (PP) filled with single and hybrid filler (silica and mica) was studied. An improvement in tensile properties and impact strength was found for both treatments compared to those of untreated composites. However, the filler with silane coupling agent showed better improvement compared to the filler with Lica‐12 coupling agent. This was due to better adhesion between filler and matrix. Thermal analysis indicates that surface treatments increased the nucleating ability of filler, but decreased the coefficient of thermal expansion of PP composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polypropylene composites. I. Studies of the effect of grafting of acrylic acid and silane coupling agent on the performance of polypropylene mica composites

To improve adhesion between polypropylene (PP) and mica in PP composites, acrylic acid (AA) is graft-copolymerized onto PP by a melt-mixing method. At the same time, applying a silane coupling agent to treat the surface of inorganic filler enhances the mechanical, thermal, and electrical properties, as well as decreases mold shrinkage and color difference of the composites.     

Mica reinforced nylon‐6: Effect of coupling agents on mechanical,thermal, and dielectric properties

The effects of applying titanate (TYZOR® TPT) and silane (DYNASYLAN VTMO) coupling agents to wet ground muscovite mica in nylon‐6 composites are described. Nylon‐6 composites of 5–40 wt % filler loadings were compounded using an APV Baker twin‐screw extruder. Mica (25 wt %) brought about an increase in the Young's modulus, flexural strength, and flexural modulus but did not produce significant variations in tensile and impact strength. Hence different coupling agents were employed. It was observed that titanate coupling agent improved the tensile strength and the Young's modulus of the composites much while the impact properties were enhanced by the silane coupling agent. An attempt was made to use ?‐caprolactum in improving the interfacial adhesion of the filler and the matrix. It was observed that ?‐caprolactum improved the flexural modulus of the composites most. The effect of coupling agents on the dielectric strength, heat distortion temperature, and morphology were also investigated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4074–4081, 2006     

Ink‐eliminated waste paper sludge flour‐filled polypropylene composites with different coupling agent treatments

Ink‐eliminated sludge flour (IESF), waste residue from the recycling treatments of waste paper, was utilized as a new kind of filler to reinforce polypropylene (PP) in this research work. Different coupling agents, including maleated anhydride grafted PP (MAPP), stearic acid (SA), and titanate (NDZ‐101), were used to increase the compatibility between IESF and PP. By using different measurements, the microstructure, morphology, thermal behaviors, and mechanical properties of the IESF/PP composites were investigated in detail. It was found that IESF, as a nucleation agent, not only induced the crystallization orientation of PP but also accelerate the crystallization rate of PP. Just as indicated in the experiments, the presence of IESF has shown the advantages of increasing the dimensional stability, the hardness and the flexural property, and the presence of coupling agents has a favorable effect on the improvement of dimensional stability. Moreover, the coupling agent has minor influence on the mechanical property, even causes some decrease in the impact strength. Among these three coupling agents, MAPP is found to be the best coupling agent for increasing the interfacial adhesion between IESF and PP, and the MAPP addition makes the PP composite possess the quickest crystallization rate and greatest tensile strength. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 513–520, 2003     

Influence of interfacial adhesion on the structural and mechanical behavior of PP‐banana/glass hybrid composites

Hybrid composites of polypropylene (PP), reinforced with short banana and glass fibers were fabricated using Haake torque rheocord followed by compression molding with and without the presence maleic anhydride grafted polypropylene (MAPP) as a coupling agent. Incorporation of both fibers into PP matrix resulted in increase of tensile strength, flexural strength, and impact strength upto 30 wt% with an optimum strength observed at 2 wt% MAPP treated 15 wt% banana and 15 wt% glass fiber. The rate of water absorption for the hybrid composites was decreased due to the presence of glass fiber and coupling agent. The effect of fiber loading in presence of coupling agent on the dynamic mechanical properties has been analyzed to investigate the interfacial properties. An increase in storage modulus (E′) of the treated‐composite indicates higher stiffness. The loss tangent (tan δ) spectra confirms a strong influence of fiber loading and coupling agent concentration on the α and β relaxation process of PP. The nature of fiber matrix adhesion was examined through scanning electron microscopy (SEM) of the tensile fractured specimen. Thermal measurements were carried out through differential scanning calorimetry (DSC) and the thermogravimetric analysis (TGA), indicated an increase in the crystallization temperature and thermal stability of PP with the incorporation of MAPP‐treated banana and glass fiber. POLYM. COMPOS., 31:1247–1257, 2010. © 2009 Society of Plastics Engineers     

Effects of vinyltrimethoxy silane on mechanical properties and morphology of polypropylene‐woodflour composites

The effects of composition and interface modification on the tensile properties and the impact resistance of different woodflour/polypropylene composites (WPC) were studied. The woodflour was treated with vinyltrimethoxy silane as a coupling agent, and its effect on the WPC properties was examined. In addition, the tensile data were fitted with several semiempirical models to clarify the mechanical behavior of the composites. The Pukánszky parameters obtained from the fit of the tensile strength data revealed that the distribution of the filler was more homogeneous in the composites containing silane and that interaction between components was improved. The impact strength was maximal for the composites containing 30% of silane‐treated woodflour. Morphological analysis by SEM revealed that the woodflour tended to form agglomerates when present in relatively high amounts in the formulations. For the silane‐treated composites, the dispersion of the filler into the polypropylene (PP) matrix improved, although surface treatment blocked the inclusion of PP into the wood cells. This probably decreased the elastic moduli, even when the filler‐matrix interaction was improved. The beneficial effects of the coupling agent on the WPC properties were greater in the materials containing a relatively low amount of filler (up to 30%); the effectiveness of 0.5% and 1% organosilane were very similar, demonstrating the effectiveness of the coupling agent. POLYM. ENG. SCI., 2009. © 2008 Society of Plastics Engineers     

Dynamic rheology,mechanical performance,shrinkage, and morphology of chemically coupled talc‐filled polypropylene

The oscillatory shear rheological properties, mechanical performance, shrinkage, and morphology of polypropylene (PP)‐talc composites chemically coupled by maleic‐anhydride‐grafted polypropylene (MAPP) were studied. The samples were prepared in a co‐rotating L/D = 40, 25 mm twin‐screw extruder. Tensile tests carried out on injection‐molded samples showed a reinforcing effect of talc up to 20 wt% on PP. Upon using MAPP, the mechanical performance of PP‐30% talc showed a maximum of about 10% increase in tensile strength at 1.5 wt% of MAPP. A Newtonian plateau (η₀) at the terminal zone was observed for the complex viscosity curve of pure PP and PP‐talc composites plotted against frequency up to 30 wt%. Upon increasing the talc content to 40 and 50 wt%, the complex viscosity at very low shear rates sharply increased and showed yield behavior that might be due to the formation of a network of filler agglomerates in the melt. Analysis of viscosity behavior in the power‐law region revealed that the flow behavior index‐n‐decreased from 0.45 for 10 wt% of talc down to about 0.4 for 40 wt% of talc. Upon increasing the talc content to 50 wt%, n decreased to a value even lower than that of the neat PP resin. The frequency of the crossover point represents molecular mobility and relaxation‐time behavior. The crossover frequency of the composites was nearly constant up to 30 wt% of talc and decreased at higher filler loadings. The optimum amount of coupling agent could be correlated with the minimum point in crossover frequency and crossover modulus. The shrinkage behavior of the composites with and without MAPP resin was studied and correlated with the rheological properties. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers     

Flour rice husk as filler in block copolymer polypropylene: Effect of different coupling agents

Flour rice husk (FRH) was employed as a filler in block copolymer polypropylene (PPB) in order to prepare polymer‐based reinforced composites. Four coupling agents were selected to modify the surface of the rice husk in the composite materials, including two types of functionalized polymers [PP homopolymer grafted with maleic anhydride (MA‐PP) and an elastomer styrene–ethylene–butadiene–styrene triblock copolymer grafted with MA (MA‐SEBS)] and two bifunctional organometallic coupling agents (silane and titanate with linear low‐density polyethylene as a carrier). The influence of each type of coupling agent on the interfacial bonding strength was studied by dynamic mechanical analysis, scanning electronic microscopy, and rheological tests. The results showed that strong interactions were formed between the coupling agents and the filler surface. The addition of a coupling agent with an elastomeric carrier (MA‐SEBS) increased the loss tangent and reduced the storage modulus of the composite. A similar but less intense effect was observed for the titanate coupling agent. However, an antagonistic performance was obtained when MA‐PP and silane were employed as coupling agents. In addition, when the percentage of MA‐SEBS was increased, the impact properties of FRH/PPB blends were improved and the strength was reduced. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1823–1831, 2006     

Effect of filler treatments on rheological behavior of calcium carbonate and talc‐filled polypropylene hybrid composites

Commercial stearic acid treated calcium carbonate (CaCO₃) was used to make a comparative study on rheological behavior of the CaCO₃ and talc‐filled polypropylene (PP) hybrid composites with nontreated filler. Apparent shear viscosity and extrudate swell were investigated with variation of filler ratio and temperature with 30% by weight total of filler was used in PP composite. The Shimadzu capillary rheometer was used to evaluate shear viscosity and shear rate of the composite. It was found that the shear viscosities decrease with increasing shear rate. The apparent shear viscosity of the composite containing the stearic acid treated is slightly lower than untreated filler. Shear thickening behavior at higher shear rate has also shown by 15/15 treated composites at higher temperature about 220°C and investigation by SEM has proved that filler being densely packed at that condition. Treated composites also exhibit lower swelling ratio value than untreated composite, and swelling ratio also decreases linearly with increasing temperature and the die length–diameter ratio. It is believed that dispersion of filler play an important role not only on shear viscosity but also on swelling ratio of PP composite. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5421–5426, 2006     

Maleic anhydride grafted polypropylene as a coupling agent for polypropylene composites filled with ink‐eliminated waste paper sludge flour

Ink‐eliminated sludge flour (IESF), a waste residue from the recycling treatment of waste paper, is a promising new kind of filler for thermoplastic polymers with a good price/performance ratio and advantages for environmental protection. In this study, high‐impact polypropylene (PP) and maleic anhydride grafted polypropylene (MAPP) were chosen as a polymer matrix and a coupling agent, respectively, for the preparation of IESF/PP composites, and the structures and properties of the obtained composites were also investigated. The experimental results revealed that IESF not only induced the crystallization orientation of PP along the b axis but also had a restraining effect on the formation of the β phase during the recrystallization of PP from the melt; the addition of MAPP further strengthened this effect to some extent. In addition, the proper addition of MAPP was helpful for improving the thermal stability of the IESF/PP composites. With the strengthening of the interfacial interaction between the IESF and PP matrix by MAPP, the resultant efficient stress transfer from the PP matrix to the IESF particles led to increased tensile and flexural strength. However, the original greater rigidity of MAPP, with respect to PP, reduced the toughness of the composites and caused some negative effects on the impact strength and the elongation at break. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2320–2325, 2004     

Synthesis and characterization of polypropylene reinforced with cellulose I and II fibers

Recently, cellulose fiber–thermoplastic composites have played an important role in some applications. Plastics reinforced with cellulose and natural fibers have been widely studied. However, composites with regenerated cellulose have rarely been investigated. In this study, the lyocell fiber of Lenzing AG (cellulose II) and its raw material a bleached hardwood pulp (cellulose I) were used as reinforcement materials. The mechanical and thermal properties of polypropylene (PP) reinforced with pulp and lyocell fibers were characterized and compared with regard to the content of the fiber and the addition of maleated polypropylene (MAPP). PPs with cellulose I or II as a reinforcement material had similar mechanical properties. However, when MAPP was used as coupling agent, the mechanical properties of the composites were different. The crystallinity of the composites were determined by differential scanning calorimetry. Cellulose I (pulp) promoted the crystallization of PP, whereas cellulose II did not. MAPP reduced this effect in cellulose I fibers, but it induced crystallization when cellulose II (lyocell) was used as a reinforcement material. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 364–369, 2006     

Cellulose nanofibril‐reinforced polypropylene composites for material extrusion: Rheological properties

Polypropylene (PP) is not typically utilized in 3D printing material extrusion because PP shrinks and warps during the printing process. Cellulose nanofibrils (CNF) have the potential to make PP 3D printer processable and also enhance mechanical properties of PP printed parts. The rheological behavior of CNF‐PP composites during material extrusion requires study because it is different from injection molding and compression molding processes. This study revealed the effects of CNF contents (3 and 10 wt%) and maleic anhydride polypropylene (MAPP) coupling agent on the rheological properties of CNF–PP composites. Morphological analysis showed that CNF agglomerated during spray drying and a spherical structure was formed. Rheological tests showed that the elastic modulus, complex viscosity, viscosity, and transient flow shear stress of PP were increased by the addition of 10 wt% CNF, while the creep strain of PP was reduced. The damping factor and stress relaxation time remained the same when 10 wt% CNF was added to the PP. Incorporation of MAPP into the CNF–PP composites impacted the rheological properties of the CNF–PP composites. Flexural strength and modulus of PP were improved by 5.9% and 26.8% by adding 10 wt% CNF compared to the control. POLYM. ENG. SCI., 2017. © 2017 Society of Plastics Engineers     

Banana/Glass Fiber-Reinforced Polypropylene Hybrid Composites: Fabrication and Performance Evaluation

Hybrid composites of Polypropylene (PP) reinforced with intimately mixed short banana and glass fibers were fabricated using Haake twin screw extruder followed by compression molding with and without the presence maleic anhydride grafted polypropylene (MAPP) as a coupling agent. Incorporation of both the fibers into PP matrix resulted in an increase in tensile, flexural and impact strength with an increasing level of fiber content upto 30 wt% at banana: glass fiber ratio of 15:15 wt% and 2 wt% of MAPP. The rate of water absorption for the hybrid composites decreased due to the presence of glass fiber and coupling agent. The effect of fiber loading in presence of coupling agent on the dynamic mechanical properties has also been analyzed to investigate the interfacial properties. An increase in the storage modulus (E′) of the treated composite indicates higher stiffness. The tan δ spectra confirms a strong influence of fiber contents and coupling agent on the α and β relaxation processes of PP. The nature of fiber matrix adhesion was examined through scanning electron microscopy (SEM) of the tensile fractured specimen. Thermal measurements were carried out employing differential scanning calorimetry (DSC) and the thermogravimetric analysis (TGA) which indicated a decrease in the crystallization temperature and thermal stability of PP with the incorporation of MAPP treated banana and Glass fiber.     

Composition,tensile properties,and dispersion of polypropylene composites reinforced with viscose fibers

The reinforcement mechanics of viscose‐fiber‐reinforced polypropylene (PP) composites were studied. The effect of the coupling agent, maleated polypropylene (MAPP), was of special interest. The fibers, coupling agent, and PP were extruded and injection‐molded. The composition, mechanical properties, fracture morphology, and dispersion of the composites were examined. Thermogravimetric analysis showed that the fiber content in the tensile specimens varied slightly with the sample location; however, the differences in the values were within 1.0%. Scanning electron microscopy images of the fracture surfaces of the composites showed that the surfaces of the composites without MAPP were covered with fibers pulled out from the matrix. A lack of adhesion further appeared as a cracked matrix–fiber interface. A new scanning thermal microscopy method, microthermal analysis, was used to study the dispersion of the fibers in the composites. Local thermal analyses gave further information about the location of the fibers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2676–2684, 2004     

Effects of vinyltrimethoxy silane on thermal properties and dynamic mechanical properties of polypropylene–wood flour composites

The viability of vinyltrimethoxy silane was investigated as a coupling agent for the manufacture of wood–plastic composites (WPC). The effect of silane pretreatment of the wood flour on the thermal and the dynamic mechanical properties and thermal degradation properties of the composites were studied. Moreover, the effect of organosilane on the properties of composites was compared with the effect of maleated polypropylene (MAPP). DSC studies indicated that the wood flour acts as a PP-nucleating agent, increasing the PP crystallization rate. In general, pretreatment with small amounts of silane improved this behavior in all the WPCs studied. Thermal degradation studies of the WPCs indicated that the presence of wood flour delayed degradation of the PP. Silane pretreatment of the wood flour augmented this effect, though without significantly affecting cellulose degradation. Studies of dynamic mechanical properties revealed that the wood flour (at up to 30 wt %) increased storage modulus values with respect to those of pure PP; in WPCs with a higher wood flour amount, there was no additional increase in storage modulus. Pretreatment of the wood flour with silane basically had no effect on the dynamic mechanical properties of the WPC. These results show that with small amounts of vinyltrimethoxy silane similar properties to the MAPP are reached. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Impact behavior of sawdust/recycled–PP composites

The instrumented Izod and Charpy tests were performed on the sawdust–polypropylene (PP) composites to study the nature of impact resistance in the thermoplastic wood composites. The notched Izod strength was found to increase with filler content in composites containing the Maleic–anhydride–grafted PP (MAPP) additive. The Izod strength even exceeds that of the neat matrix resin at higher filler contents, indicating a methodology for applying the recycled PP and also for reinforcing the thermoplastics with wood powders. While the static tensile results show evidences for the reinforcing role of the wood filler, a fracture mechanics characterization through the Charpy impact tests effects of MAPP under the impact loading rates. The choice of MAPP as the additive was discussed accordingly for application of the sort of materials. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1420–1428, 2001     

An investigation on the mechanical and dynamic rheological properties of single and hybrid filler/polypropylene composites based on talc and calcium carbonate

Some results of experiments on the mechanical and rheological properties of mineral filled polypropylene were presented. Single filler and hybrid filler composites of talc and calcium carbonate (CaCO₃) were prepared in a co‐rotating twin‐screw extruder. The effect of filler type, filler content, and coupling agent on the mechanical and rheological properties of the polypropylene were studied. The coupling agent was maleic anhydride‐grafted polypropylene (PP‐g‐MA). It was found that the mechanical properties are affected by filler type, filler concentration, and the interaction between filler and matrix. The tensile strength of the composite is more affected by the talc while the impact strength is influenced mostly by CaCO₃ content. The elongation at break of PP/CaCO₃ composites was higher than that of PP/talc composites. The incorporation of coupling agent into PP/mineral filler composites increased the mechanical properties. Rheological properties indicated that the complex viscosity and storage modulus of talc filled samples were higher than those of calcium carbonate filled samples while the tan δ was lower. The rheological properties of hybrid‐filler filled sample were more affected by the talc than calcium carbonate. The PP‐g‐MA increased the complex viscosity and storage modulus of both single and hybrid composites. POLYM. COMPOS., 2009. © 2009 Society of Plastics Engineers     

Morphological,mechanical, and physical properties of composites made with wood flour‐reinforced polypropylene/recycled poly(ethylene terephthalate) blends

Wood flour (WF)‐filled composites based on a polypropylene (PP)/recycled polyethylene terephthalate (r‐PET) matrix were prepared using two‐step extrusion. Maleic anhydride grafted polypropylene (MAPP) was added to improve the compatibility between polymer matrices and WF. The effects of filler and MAPP compatibilization on the water absorption, mechanical properties, and morphological features of PP/r‐PET/WF composites were investigated. The addition of MAPP significantly improved mechanical properties such as tensile strength, flexural strength, tensile modulus, and flexural modulus compared with uncompatibilized composites, but decreased elongation at break. Scanning electron microscopic images of fracture surface specimens revealed better interfacial interaction between WF and polymer matrix for MAPP‐compatibilized PP/r‐PET/WF composites. MAPP‐compatibilized PP/r‐PET/WF composites also showed reduced water absorption due to improved interfacial bonding, which limited the amount of absorbable water molecules. These results indicated that MAPP acts as an effective compatibilizer in PP/r‐PET/WF composites. POLYM. COMPOS., 38:1749–1755, 2017. © 2015 Society of Plastics Engineers     

Effects of hygrothermal ageing on mechanical properties of flax pulps and their polypropylene matrix composites

The aim of this work was to study the kinetics of water uptake and its influence on mechanical behavior of both flax pulps and their composites with a maleic anhydride polypropylene copolymer (MAPP) modified polypropylene (PP) matrix by immersion in distilled water at 30, 50, 70, and 100°C. Both the influence of two different MAPP compatibilizers and the optimum doses of each ones were analyzed. The kinetics of water uptake was studied from weight measurements at regular interval times. The diffusion coefficient was dependent on the immersion temperature and MAPP content. Tensile modulus and strength of single flax fiber decreased by water immersion. Both flexural strength and modulus of composites decreased as a result of the combined effect of thermal ageing and moisture absorption. MAPP coupling agent increases moisture resistance and mechanical properties for MAPP‐modified systems with respect to the unmodified ones. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3438–3445, 2006     

The influence of filler treatment on the properties of TPU/PP blends: I. Thermal properties and stability

Commercially available organosilane (3‐glycidoxypropyltrimethoxysilane (GPTMS)) coupling agent was used to treat talc in order to improve the affinity relative between the filler and the polymer in composites as well as filler and polymer in the thermoplastic polyurethane/polypropylene (TPU/PP) blends (talc content was 5 wt%). The talc particles were first modified with GPTMS and then introduced into TPU, PP as well as TPU/PP blends with different weight ratios of polymers using blending method and subsequently injection molded in a hydraulic press. The aim was to report the effect of silane coupling agent on the thermal and morphological properties of talc filled composites and blends. The results showed that the thermal properties of the TPU, PP composites and TPU/PP blends were improved with the addition of silane treated talc (higher melting (T_m), crystallization (T_c) temperatures and degree of crystallinity (χ_c)). The glass transition temperature (T_g) obtained by dynamic mechanical analysis (DMA) of the TPU soft segments in TPU/PP blends increased with the addition of untreated and silane treated talc due to lower mobility of the soft segments in TPU and better miscibility of TPU and PP. TPU/PP blends with the silane treated talc show better thermal stability than the TPU/PP blends with untreated talc. POLYM. ENG. SCI., 55:1920–1930, 2015. © 2014 Society of Plastics Engineers