Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(styrene‐co‐acrylonitrile)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMAs) (designated as iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(styrene‐co‐acrylonitrile) (abbreviated as PSAN) containing 25 wt % of acrylonitrile in tetrahydrofuran to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PSAN. The aPMMA/PSAN and sPMMA/PSAN blends were found to be miscible because all the prepared films were transparent and showed composition dependent glass transition temperatures (T_gs). The glass transition temperatures of the two miscible blends were fitted well by the Fox equation, and no broadening of the glass transition regions was observed. The iPMMA/PSAN blends were found to be immiscible, because most of the cast films were translucent and had two glass transition temperatures. Through the use of a simple binary interaction model, the following comments can be drawn. The isotactic MMA segments seemed to interact differently with styrene and with acrylonitrile segments from atactic or syndiotactic MMA segments. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2894–2899, 1999     

Viscoelastic properties of blends of poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile) having various acrylonitrile contents

Dynamic viscoelastic properties of blends of poly(methyl methacrylate) (PMMA) and poly(styrene‐co‐acrylonitrile) (SAN) with various AN contents were measured to evaluate the influence of SAN composition, consequently χ parameter, upon the melt rheology. PMMA/SAN blends were miscible and exhibited a terminal flow region characterized by Newtonian flow, when the acrylonitrile (AN) content of SAN ranges from 10 to 27 wt %. Whereas, PMMA/SAN blends were immiscible and exhibited a long time relaxation, when the AN content in SAN is less than several wt % or greater than 30 wt %. Correspondingly, melt rheology of the blends was characterized by the plots of storage modulus G′ against loss modulus G″. Log G′ versus log G″ plots exhibited a straight line of slope 2 for the miscible blends, but did not show a straight line for the immiscible blends because of their long time relaxation mechanism. The plateau modulus, determined as the storage modulus G′ in the plateau zone at the frequency where tan δ is at maximum, varied linearly with the AN content of SAN irrespective of blend miscibility. This result indicates that the additivity rule holds well for the entanglement molecular weights in miscible PMMA/SAN blends. However, the entanglement molecular weights in immiscible blends should have “apparent” values, because the above method to determine the plateau modulus is not applicable for the immiscible blends. Effect of χ parameter on the plateau modulus of the miscible blends could not be found. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphology and thermal behavior of organo‐bentonite clay/poly(styrene‐co‐methacrylic acid)/poly(isobutyl methacrylate‐co‐4‐vinylpyridine) nanocomposites

Poly(styrene‐co‐methacrylic acid) containing 29 mol % of methacrylic acid (SMA‐29) and poly(isobutyl methacrylate‐co‐4‐vinylpyridine) containing 20 mol % of 4‐vinylpyridine (IBM4VP‐20) were synthesized, characterized, and used to elaborate binary and ternary nanocomposites of different ratios with a 3% by weight hexadecylammonium‐modified bentonite from Maghnia (Algeria) by casting method from tetrahydrofuran (THF) solutions. The morphology and the thermal behavior of these binary and ternary elaborated nanocomposites were investigated by X‐ray diffraction, scanning electron microscopy, FTIR spectroscopy, differential scanning calorimetry, and thermogravimetry. Polymer nanocomposites and nanoblends of different morphologies were obtained. The effect of the organoclay and its dispersion within the blend matrix on the phase behavior of the miscible SMA29/IBM4VP20 blends is discussed. The obtained results showed that increasing the amount of SMA29 in the IBM4VP20/SMA29 blend leads to near exfoliated nanostructure with significantly improved thermal stability. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Biodegradable blends of high molecular weight poly(ethylene oxide) with poly(3‐hydroxypropionic acid) and poly(3‐hydroxybutyric acid): a miscibility study by DSC,DMTA and NMR spectroscopy

The miscibility of high molecular weight poly(ethylene oxide) blends with poly(3‐hydroxypropionic acid) and poly(3‐hydroxybutyric acid) (P(3HB)) has been investigated by differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA) and high‐resolution solid state ¹³C nuclear magnetic resonance (NMR). The DSC thermal behaviour of the blends revealed that the binary blends of poly(ethylene oxide)/poly(3‐hydroxypropionic acid) (OP blends) were miscible over the whole composition range while the miscibility of poly(ethylene oxide)/poly(3‐hydroxybutyric acid) blends (OB blends) was dependent on the blend composition. OB blends were found to be partly miscible at the middle P(3HB) contents (25 %, 50 %) and miscible at other P(3HB) contents (10 %, 75 % and 90 %). Single‐phase behaviour for OP blends and phase separation behaviour for OB blends were observed from DMTA. The results from NMR spectroscopy revealed that the two components in the OP50 blend were intimately mixed on a scale of about 35 nm, while the domain sizes in the OB blend with a P(3HB) content of 50 % were larger than about 32 nm. © 2000 Society of Chemical Industry     

Phase behavior of ternary blends containing dimethylpolycarbonate,tetramethylpolycarbonate and poly[styrene‐co‐(methyl methacrylate)] copolymers (or polystyrene)

The miscibility and phase behavior of ternary blends containing dimethylpolycarbonate (DMPC), tetramethylpolycarbonate (TMPC) and poly[styrene‐co‐(methyl methacrylate)] copolymer (SMMA) have been explored. Ternary blends containing polystyrene (PS) instead of SMMA were also examined. Blends of DMPC with SMMA copolymers (or PS) did not form miscible blends regardless of methyl methacrylate (MMA) content in copolymers. However, DMPC blends with SMMA (or PS) blends become miscible by adding TMPC. The miscible region of ternary blends is compared with the previously determined miscibility region of binary blends having the same chemical components and compositions. The region where the ternary blends are miscible is much narrower than that of binary blends. Based on lattice fluid theory, the observed phase behavior of ternary blends was analyzed. Even though the term representing the Gibbs free energy change of mixing for certain ternary blends had a negative value, blends were immiscible. It was revealed that a negative value of the Gibbs free energy change of mixing was not a sufficient condition for miscible ternary blends because of the asymmetry in the binary interactions involved in ternary blends. Copyright © 2004 Society of Chemical Industry     

Compatibility and thermal properties of poly(acrylonitrile–butadiene–styrene) copolymer blends with poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile)

The mechanical and heat‐resistant properties of acrylonitrile–butadiene–styrene (ABS) binary and ternary blends were investigated. The relationship of compatibility and properties was discussed. The results show that poly(methyl methacrylate) (PMMA) and styrene–maleic anhydride (SMA) can improve the thermal properties of conventional ABS. The Izod impact property of ABS/PMMA blends increases significantly with the addition of PMMA, whereas that of ABS/SMA blends decreases significantly with the addition of SMA. Blends mixed with high‐viscosity PMMA are characterized by higher heat‐distortion temperature (HDT), and their heat resistance is similar to that of blends mixed with SMA. For high‐viscosity PMMA, from 10 to 20%, it is clear that blends appear at the brittle–ductile transition, which is related to the compatibility of the two phases. TEM micrographs show low‐content and high‐viscosity PMMA in large, abnormally shaped forms in the matrix. Compatibility between PMMA and ABS is dependent on both the amount and the viscosity of PMMA. When the amount of high‐viscosity PMMA varied from 10 to 20 wt %, the morphology of the ABS binary blends varied from poor to satisfactory compatibility. As the viscosity of PMMA decreases, the critical amount of PMMA needed for the compatibility of the two phases also decreases. SMA, as a compatibilizer, improved the interfacial adhesiveness of ABS and PMMA, which results in PMMA having good dispersion in the matrix. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2652–2660, 2002     

Criteria dilemma of phase behavior in ternary blends comprising polystyrene, poly(alpha-methyl styrene), and poly(4-methyl styrene)

A ternary blend system of polystyrene (aPS), poly(α-methyl styrene) (PαMS), and poly(4-methyl styrene) (P4MS) (blends of three styrenic homopolymers of similar molecular structures) was investigated by using differential scanning calorimetry (DSC), polarized-light optical microscopy (POM), scanning electron microscopy (SEM), and solid-state ¹³C cross-polarization/magic angle spinning nuclear magnetic resonance (CP/MAS NMR). This ternary system of aPS/PαMS/P4MS exhibits a small miscibility loop only at relatively high percentages of PαMS (≥80%), while most of the aPS/PαMS/P4MS compositions exhibit two coexisting aPS/PαMS and aPS/P4MS phases in the immiscibility loop. In the immiscible loop, SEM measurements revealed evidence in contrasting with DSC for criteria of miscibility. DSC characterization revealed a single T_g for most ternary blend compositions; however, SEM graphs apparently indicated sub-micron phase domains, except for several PαMS-rich compositions (>80%). The and techniques using NMR were found to resolve the dilemma between the conventional thermal analysis and microscopy results, and indeed supported that the ternary blends at above 80% PαMS are completely homogeneous on the molecular level. Attempts have been made to resolve the seemingly contradictory interpretations on the complex ternary phase structures and domains from the DSC, and microscopy results.     

Binary and ternary polymer blends containing poly(vinylidene chloride‐co‐acrylonitrile)

Poly(vinylidene chloride‐co‐acrylonitrile) (Saran F), poly(hydroxy ether of bisphenol A) (phenoxy), poly(styrene‐co‐acrylonitrile) (PSAN), and poly(vinyl phenol) (PVPh) all have the same characteristic: miscibility with atactic poly(methyl methacrylate) (aPMMA). However, the miscibility of Saran F with the other polymer (phenoxy, PSAN, or PVPh) is not guaranteed and was thus investigated. Saran F was found to be miscible only with PSAN but not miscible with phenoxy and PVPh. Because Saran F and PVPh are not miscible, although they are both miscible with aPMMA, aPMMA can thus be used as a potential cosolvent to homogenize PVPh/Saran F. The second part of this report focused on the miscibility of a ternary blend consisting of Saran F, PVPh, and aPMMA to investigate the cosolvent effect of aPMMA. Factors affecting the miscibility were studied. The established phase diagram indicated that the ternary blends with high PVPh/Saran F weight ratio were found to be mostly immiscible. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3068–3073, 2004     

Synthesis and characterization of p‐perfluoro{1‐[2‐(2‐fluorosulfonyl‐ethoxy)propoxy]}ethylated poly(α‐methyl styrene)

p‐Perfluoro{1‐[2‐(2‐fluorosulfonyl‐ethoxy)propoxy]}ethylated poly(α‐ methyl styrene) 3 was synthesized via electron transfer of perfluoro‐di{2‐[2‐(2‐fluorosulfonyl‐ethoxy)propoxy]}propionyl peroxide 2 and poly(α‐methyl styrene) 1 at different reactant molar ratios (2 : 1). The modified polymer 3 was characterized by various techniques. The ring p‐substitution was proved by FTIR and ¹⁹FNMR. The desulfonation appeared at above 124°C was found by TGA. The molecular weight determined by GPC increased with the increase of reactant molar ratio, and the polydispersity values indicated there was no degradation of the parent polymer chain in the reaction. Followed by hydrolysis and acidification, the modified polymer 3 could be further quantitatively converted into its sulfonic form 4. Ion exchange capacity of novel polyelectrolyte 4 can be controlled by changing reactant molar ratio (2 : 1). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3615–3618, 2006     

Phase behavior of binary and ternary blends of poly(styrene‐co‐methacrylic acid), poly(styrene‐co‐4‐vinylpyridine), and poly(2,6‐dimethyl‐1,4‐phenylene oxide)

Poly(styrene‐co‐methacrylic acid) (PSMA) and poly(styrene‐co‐4‐vinylpyridine) (PS4VP) of different compositions were prepared and characterized. The phase behavior of these copolymers as binary PSMA/PS4VP mixtures or with poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) as PPO/PSMA or PPO/PS4VP and PPO/PSMA/PS4VP ternary blends was investigated by differential scanning calorimetry (DSC). This study showed that PPO was miscible with PS4VP containing up to 15 mol % 4‐vinylpyridine (4VP) but immiscible with PS4VP‐30 (where the number following the hyphen refers to the percentage 4VP in the polymer) and PSMA‐20 (where the number following the hyphen refers to the percentage methacrylic acid in the polymer) over the entire composition range. To examine the morphology of the immiscible blends, scanning electron microscopy was used. Because of the hydrogen‐bonding specific interactions that occurred between the carboxylic groups of PSMA and the pyridine groups of PS4VP, chloroform solutions of PSMA‐20 and PS4VP‐15 formed interpolymer complexes. The obtained glass‐transition temperatures (T_g's) of the PSMA‐20/PS4VP‐15 complexes were found to be higher than those calculated from the additivity rule. Although, depending on the content of 4VP, the shape of the T_g of the PPO/PS4VP blends changed from concave to S‐shaped in the case of the miscible blends, two T_g were observed with each PPO/PS4VP‐30 and PPO/PS4VP‐40 blend. The thermal stability of the PSMA‐20/PS4VP‐15 interpolymer complexes was studied by thermogravimetry. On the basis of the obtained results, the phase behavior of the ternary PPO/PSMA‐20/PS4VP‐15 blends was investigated by DSC. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Miscibility and crystallization kinetics of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/ poly(methyl methacrylate) blends

The miscibility and crystallization kinetics of the blends of random poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(HB‐co‐HV)] copolymer and poly(methyl methacrylate) (PMMA) were investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PMMA blends were miscible in the melt. Thus the single glass‐transition temperature (T_g) of the blends within the whole composition range suggests that P(HB‐co‐HV) and PMMA were totally miscible for the miscible blends. The equilibrium melting point (T°_m) of P(HB‐co‐HV) in the P(HB‐co‐HV)/PMMA blends decreased with increasing PMMA. The T°_m depression supports the miscibility of the blends. With respect to the results of crystallization kinetics, it was found that both the spherulitic growth rate and the overall crystallization rate decreased with the addition of PMMA. The kinetics retardation was attributed to the decrease in P(HB‐co‐HV) molecular mobility and dilution of P(HB‐co‐HV) concentration resulting from the addition of PMMA, which has a higher T_g. According to secondary nucleation theory, the kinetics of spherulitic crystallization of P(HB‐co‐HV) in the blends was analyzed in the studied temperature range. The crystallizations of P(HB‐co‐HV) in P(HB‐co‐HV)/PMMA blends were assigned to n = 4, regime III growth process. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3595–3603, 2004     

Effect of in situ polymerization conditions of methyl methacrylate on the structural and morphological properties of poly(methyl methacrylate)/poly(acrylonitrile‐g‐(ethylene‐co‐propylene‐co‐diene)‐g‐styrene) PMMA/AES Blends

In this study, the structural and morphological properties of poly(methyl methacrylate)/poly(acrylonitrile‐g‐(ethylene‐co‐propylene‐co‐diene‐g‐styrene) (PMMA‐AES) blends were investigated with emphasis on the influence of the in situ polymerization conditions of methyl methacrylate. PMMA‐AES blends were obtained by in situ polymerization, varying the solvent (chloroform or toluene) and polymerization conditions: method A—no stirring and air atmosphere; method B—stirring and N₂ atmosphere. The blends were characterized by infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and dynamic mechanical analysis (DMA). The results showed that the PMMA‐AES blends are immiscible and present complex morphologies. This morphology shows an elastomeric dispersed phase in a glassy matrix, with inclusion of the matrix in the elastomer domains, suggesting core shell or salami morphology. The occlusion of the glassy phase within the elastomeric domains can be due to the formation of graft copolymer and/or phase inversion during polymerization. However, this morphology is affected by the polymerization conditions (stirring and air or N₂ atmosphere) and by the solvent used. The selective extraction of the blends' components and infrared spectroscopy showed that crosslinked and/or grafting reactions occur on the elastomer chains during MMA polymerization. The glass transition of the elastomer phase is influenced by morphology, crosslinking, and grafting degree and, therefore, T_g depends on the polymerization conditions. On the other hand, the behavior of T_g of the glassy phase with blend composition suggests miscibility or partial miscibility for the SAN phase of AES and PMMA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Thermal,mechanical, and morphological characterization studies of poly(2,6‐dimethyl‐1,4‐phenylene oxide) blends with polystyrene and brominated polystyrene

The miscibility of the binary and ternary blends of poly(2,6‐dimethyl‐1,4‐phenylene oxide), brominated polystyrene, and polystyrene was investigated using a differential scanning calorimeter. The morphology of these blends was characterized by scanning electron microscopy. These studies revealed a close relation between the blend structure and its mechanical properties. The compatibilizing effect of poly(2,6‐dimethyl‐1,4‐phenylene oxide) on the miscibility of the polystyrene/brominated polystyrene blends was examined. It was found that poly(2,6‐dimethyl‐1,4‐phenylene oxide), which was miscible with polystyrene and partially miscible with brominated polystyrene, compatibilizes these two immiscible polymers if its contention exceeds 33 wt %. Upon the addition of poly(2,6‐dimethyl‐1,4‐phenylene oxide) to the immiscible blends of polystyrene/brominated polystyrene, we observed a change in the morphology of the mixtures. An improvement in the mechanical properties was noticed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 225–231, 2000     

Melt rheology of poly(ϵ‐caprolactone)/poly(styrene‐co‐acrylonitrile) blends

Dynamic viscoelastic properties for miscible blends of poly(?‐caprolactone) (PCL) and poly(styrene‐co‐acrylonitrile) (SAN) were measured. It was found that the time–temperature superposition principle is applicable over the entire temperature range studied for the blends. The temperature dependency of the shift factors a_T can be expressed by the Williams–Landel–Ferry equation: log a_T = ?8.86(T ? T_s)/(101.6 + T ? T_s). The compositional dependency of T_s represents the Gordon–Taylor equation. The zero‐shear viscosities are found to increase concavely upward with an increase in weight fraction of SAN at constant temperature, but concavely downward at constant free volume fraction. It is concluded that the relaxation behavior of the PCL/SAN blends is similar to that of a blend consisting of homologous polymers. It is emphasized that the viscoelastic functions of the miscible blends should be compared in the iso‐free volume state. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2037–2041, 2001     

Influence of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) on miscibility and properties of atactic poly(methyl methacrylate)

Miscibility and properties of two atactic poly(methyl methacrylate)‐based blends [containing 10 and 20% of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)] have been investigated as a function of thermal treatments. Differential scanning calorimetry and dynamic mechanical thermal analysis of blends quenched in liquid nitrogen or ice/water, after annealing at T > 190 °C, showed a single glass transition temperature, indicating miscibility of the components for the time‐temperature history. Two glass transition temperatures, equal to those of the pure components, are instead found for blends after annealing at T < 190 °C. Scanning electron microscopy confirmed the homogeneity for the former quenched blends and phase separation for the latter. These results indicate the presence of an upper critical solution temperature (UCST). Tensile experiments, performed on two series of samples annealed at temperatures above and below the UCST, showed that the copolyester induces a decrease of Young's modulus and stresses at yielding and break points, and a marked increase of elongation at break. Differences in tensile properties between the two series of annealed blends are accounted for by the physical state of the components at room temperature after annealing above or below the UCST. Copyright © 2004 Society of Chemical Industry     

Specific interactions in poly(styrene‐co‐2‐hydroxyethyl acrylate)/poly(styrene‐co‐N,N‐dimethylacrylamide) systems

Amphiphilic copolymers of poly(styrene‐co‐2‐hydroxyethyl acrylate) (SHEA) and poly(styrene‐co‐N, N‐dimethylacrylamide) (SAD) of different compositions were prepared by free radical copolymerization and characterized by different techniques. Depending on the nature of the solvent and the densities of interacting species incorporated within the polystyrene matrices, novel materials as blends or interpolymer complexes with properties different from those of their constituents were elaborated when these copolymers are mixed together. The specific interpolymer interactions of hydrogen bonding type and the phase behavior of the elaborated materials were investigated by differential scanning calorimetry (DSC) and Fourier transform infra red spectroscopy (FTIR). The specific interactions of hydrogen bonding type that occurred within the SHEA and within their blends with the SAD were evidenced by FTIR qualitatively by the appearance of a new band at 1626 cm^?1 and quantitatively using appropriate spectral curve fitting in the carbonyl and amide regions. The variation of the glass transition temperature with the blend composition behaved differently with the densities of interacting species. The thermal degradation behavior of the materials was studied by thermogravimetry. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Interpolymer‐specific interactions and miscibility in poly(styrene‐co‐acrylic acid)/poly(styrene‐co‐N,N‐dimethylacrylamide) blends

The miscibility or complexation of poly(styrene‐co‐acrylic acid) containing 27 mol % of acrylic acid (SAA‐27) and poly(styrene‐co‐N,N‐dimethylacrylamide) containing 17 or 32 mol % of N,N‐dimethylacrylamide (SAD‐17, SAD‐32) or poly(N,N‐dimethylacrylamide) (PDMA) were investigated by different techniques. The differential scanning calorimetry (DSC) analysis showed that a single glass‐transition temperature was observed for all the mixtures prepared from tetrahydrofuran (THF) or butan‐2‐one. This is an evidence of their miscibility or complexation over the entire composition range. As the content of the basic constituent increases as within SAA‐27/SAD‐32 and SAA‐27/PDMA, higher number of specific interpolymer interactins occurred and led to the formation of interpolymer complexes in butan‐2‐one. The qualitative Fourier transform infrared (FTIR) spectroscopy study carried out for SAA‐27/SAD‐17 blends revealed that hydrogen bonding occurred between the hydroxyl groups of SAA‐27 and the carbonyl amide of SAD‐17. Quantitative analysis carried out in the 160–210°C temperature range for the SAA‐27 copolymer and its blends of different ratios using the Painter–Coleman association model led to the estimation of the equilibrium constants K₂, K_A and the enthalpies of hydrogen bond formation. These blends are miscible even at 180°C as confirmed from the negative values of the total free energy of mixing ΔG_M over the entire blend composition. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1011–1024, 2007     

Thermal properties of blends of poly(hydroxybutyrate‐co‐hydroxyvalerate) and poly(styrene‐co‐acrylonitrile)

Thermal properties of blends of poly(hydroxybutyrate‐co‐hydroxyvalerate) (PHBV) and poly(styrene‐co‐acrylonitrile) (SAN) prepared by solution casting were investigated by differential scanning calorimetry. In the study of PHBV‐SAN blends by differential scanning calorimetry, glass transition temperature and melting point of PHBV in the PHBV‐SAN blends were almost unchanged compared with those of the pure PHBV. This result indicates that the blends of PHBV and SAN are immiscible. However, crystallization temperature of the PHBV in the blends decreased approximately 9–15°. From the results of the Avrami analysis of PHBV in the PHBV‐SAN blends, crystallization rate constant of PHBV in the PHBV‐SAN blends decreased compared with that of the pure PHBV. From the above results, it is suggested that the nucleation of PHBV in the blends is suppressed by the addition of SAN. From the measured crystallization half time and degree of supercooling, interfacial free energy for the formation of heterogeneous nuclei of PHBV in the PHBV‐SAN blends was calculated and found to be 2360 (mN/m)³ for the pure PHBV and 2920–3120 (mN/m)³ for the blends. The values of interfacial free energy indicate that heterogeneity of PHBV in the PHBV‐SAN blends is deactivated by the SAN. This result is consistent with the results of crystallization temperature and crystallization rate constant of PHBV in the PHBV‐SAN blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 673–679, 2000     

Miscibility of polymer blends of poly(styrene‐co‐4‐hydroxystyrene) with bisphenol‐A polycarbonate

The miscibility of blends of bisphenol‐A polycarbonate (BAPC) and tetramethyl bisphenol‐A polycarbonate (TMPC) with copolymers of poly(styrene‐co‐4‐hydroxystyrene) (PSHS) was studied in this work. It has been demonstrated that BAPC is miscible with PSHS over a region of approximately 45–75 mol % hydroxyl groups in the copolymer. TMPC has a wider miscible window than BAPC when blended with PSHS. The blend miscibility was considered to be driven by the intermolecular attractive interactions between the hydroxyl groups of the PSHS and the π electrons of the aromatic rings of both polycarbonates (PCs). As the FTIR measurements showed, after blending of BAPC with PSHS, there is no visible shift of the carbonyl band of BAPC at 1774 cm⁻¹, whereas the stretching frequency of the free hydroxyl groups of the copoly‐ mers at 3523 cm⁻¹ disappeared. The large positive values of the segment interaction energy density parameter B_st‐HS calculated from the group contribution approach indicated that the intramolecular repulsive interaction may also have played a role in the promotion of the blend miscibility. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 639–646, 1999     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by melt mixing. The miscibility, crystallization behavior, mechanical properties and hydrophilicity of the ternary blends have been investigated. The high compatibility of PVDF/PMMA/PVP ternary blends is induced by strong interactions between the carbonyl groups of the PMMA/PVP blend and the CF₂ or CH₂ group of PVDF. According to the Fourier transform infrared and wide‐angle X‐ray difffraction analyses, the introduction of PMMA does not change the crystalline state (i.e. α phase) of PVDF. By contrast, the addition of PVP in the blends favors the transformation of the crystalline state of PVDF from non‐polar α to polar β phase. Moreover, the crystallinity of the PVDF/PMMA/PVP ternary blends also decreases compared with neat PVDF. Through mechanical analysis, the elongation at break of the blends significantly increases to more than six times that of neat PVDF. This confirms that the addition of the PMMA/PVP blend enhances the toughness of PVDF. Besides, the hydrophilicity of PVDF is remarkably improved by blending with PMMA/PVP; in particular when the content of PVP reaches 30 wt%, the water contact angle displays its lowest value which decreased from 91.4° to 51.0°. Copyright © 2011 Society of Chemical Industry