Phase separation of poly (methyl methacrylate) / poly (styrene-co-acrylonitrile) blends in the presence of silica nanoparticles

The effects of silica nanoparticles on the phase separation of poly (methyl methacrylate)/poly (styrene-co-acrylonitrile) (PMMA/SAN) blends are studied by the rheological method. The binodal temperatures of near-critical compositions were obtained by the gel-like behavior during spinodal decomposition, which is a character of polymer blends with co-continuous morphology. The shifted Cole–Cole plot method was introduced to determine the binodal temperatures of off-critical compositions based on the appearance of shoulder-like transition in the terminal regime of blends with droplet morphology. Such method is found also applicable in nanoparticle filled polymer blends. Moreover, a new method to determine the spinodal temperature from Fredrickson-Larson mean field theory was suggested, where the concentration fluctuation's contribution to the storage modulus is used instead of the whole dynamic moduli. This method was also successfully extended to nanoparticle filled polymer blend. The influences of the concentration and the average diameter of silica particles on the phase separation temperature were studied. It was found that the small amount of the silica nanoparticles in PMMA/SAN blends will significantly change the phase diagram, which is related to the selective location of silica in PMMA. The comparisons with thermodynamic theory of particle-filled polymer blends are also discussed.     

Phase behavior and properties of poly(methyl methacrylate)/poly(vinyl acetate) blends prepared via in situ polymerization

Polymer blends composed of poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) were prepared via radical-initiated polymerization of methyl methacrylate (MMA) in the presence of PVAc. Differential scanning calorimetry and dynamic mechanical analysis were employed to investigate the miscibility and phase behavior of the blends. The PMMA/PVAc blends of in situ polymerization were found to be phase separated and exhibited a two-phase structure, although some chain transferring reaction between the components occurred. The phase separation resulted from the solvent effect of MMA during the in situ polymerization, which was confirmed by the investigation of phase behavior based on solution cast blending. Solubility analysis of the polymerized blends indicated that some chain transferring reaction between the components occurred during the polymerization. An abrupt increase in gel content from 21.2 to 72.4 wt % was observed when the inclusion of PVAc increased from 30 to 40 wt %, and the gel component consisted of the component polymers as shown by infrared spectroscopy studies. The thermogravimetric analysis study indicated that the inclusion of a small amount of PVAc gives rise to a marked stabilization effect on the thermal stability. The PMMA/PVAc blends exhibited increased notched impact properties with the inclusion of 5 wt % PVAc. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 675–684, 1998     

Influence of the tacticity of poly(methyl methacrylate) on the miscibility with poly(vinyl chloride)

It can be concluded from the work of Schurer et al.¹⁰ that poly(vinyl chloride) (PVC) is more miscible with syndiotactic than with isotactic poly(methyl methacrylate) (PMMA). By choosing different molar masses for the various tactic forms of PMMA it is possible to obtain blends with PVC with similar phase behaviour, i.e. in all cases a cloud-point curve with a minimum in the vicinity of 190°C. In this way a more quantitative statement about the influence of the tacticity of PMMA on its miscibility with PVC can be made. One of the principal differences between syndiotactic or atactic PMMA and isotactic PMMA is the higher flexibility of the latter. Using Flory's equation of state theory it will be shown that the effect of this difference is large enough to explain the difference in phase behaviour observed. Heats of mixing of low molar mass analogues were also measured and found to be negative.     

Preparation of graded materials for miscible polycarbonate/poly(methyl methacrylate) blends by segregation under shear flow

Exposure to shear flow produced by a pressure-driven capillary rheometer provides a concentration gradient without phase separation in miscible polymer blends of bisphenol-A polycarbonate containing low-molecular-weight poly(methyl methacrylate) (PMMA). The strand surface extruded from the rheometer contains a large amount of PMMA. However, the strand is transparent because there is no light scattering due to phase separation. The segregation behavior, that is, enrichment of the PMMA content at the strand surface, is enhanced when the molecular weight of PMMA is low. Furthermore, the segregation is also enhanced at high temperatures and at high shear rates. By contrast, the die length barely affects the degree of segregation. The segregation phenomenon should be noted because it may facilitate the modification of the surface properties of various products.     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by melt mixing. The miscibility, crystallization behavior, mechanical properties and hydrophilicity of the ternary blends have been investigated. The high compatibility of PVDF/PMMA/PVP ternary blends is induced by strong interactions between the carbonyl groups of the PMMA/PVP blend and the CF₂ or CH₂ group of PVDF. According to the Fourier transform infrared and wide‐angle X‐ray difffraction analyses, the introduction of PMMA does not change the crystalline state (i.e. α phase) of PVDF. By contrast, the addition of PVP in the blends favors the transformation of the crystalline state of PVDF from non‐polar α to polar β phase. Moreover, the crystallinity of the PVDF/PMMA/PVP ternary blends also decreases compared with neat PVDF. Through mechanical analysis, the elongation at break of the blends significantly increases to more than six times that of neat PVDF. This confirms that the addition of the PMMA/PVP blend enhances the toughness of PVDF. Besides, the hydrophilicity of PVDF is remarkably improved by blending with PMMA/PVP; in particular when the content of PVP reaches 30 wt%, the water contact angle displays its lowest value which decreased from 91.4° to 51.0°. Copyright © 2011 Society of Chemical Industry     

Probing the structure of polymer blends by vibrational spectroscopy: the case of poly(ethylene oxide) and poly(methyl methacrylate) blends

The blends of poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) are prepared in the form of thin films from solution casting. The Fourier transform infrared spectra of the blends are recorded in the spectral range 400–4000 cm^?1. The spectra are analysed using various recent techniques of vibrational spectroscopy. It is concluded that upon blending PEO takes preferentially a planar zig-zag structure. Furthermore the intermolecular interactions between the molecules of PEO and PMMA in blends are very weak and their compatibility as blends is more ‘physical’ than ‘chemical’. Further, on the basis of the atomic charges transferred from model molecules it is seen that the blending is preferred with isotactic PMMA when compared to syndiotactic PMMA.     

Kinetics of phase separation of poly(styrene‐co‐methyl methacrylate) and poly(styrene‐co‐acrylonitrile) blends

The phase behavior and kinetics of phase separation for blends of the random copolymer poly(styrene‐co‐methyl methacrylate) (SMMA) and poly(styrene‐co‐acrylonitrile) (SAN) were studied by using small‐angle laser light scattering. The partially miscible SMMA/SAN blends undergo spinodal decomposition (SD) and subsequent domain coarsening when quenched inside the unstable region. For blends of SMMA and SAN, the early stages of the phase separation process could be observed, unlike a number of other blends where the earliest stages are not visible by light scattering. The process was described in terms of the Cahn–Hilliard linear theory. Subsequently, a coarsening process was detected and the time evolution of q_m at the beginning of the late stages of phase separation followed the relationship q_m∝t^?1/3, corresponding to an evaporation–condensation mechanism. Self‐similar growth of the phase‐separated structures at different timescales was observed for the late stage. Copyright © 2004 Society of Chemical Industry     

Phase behaviour and phase separation in polymer blends of poly(methyl methacrylate) with poly(vinyl acetate)

Summary Phase behaviour and phase separation in a binary polymer blends of poly(methyl methacryate) (PMMA) with poly(vinyl acetate) (PVAc) was invistigated by cloud method and light scattering. A lower critical solution temperature (LCST) type phase diagram was found. The mixture system of PMMA/PVAc is miscible. Kinetic study on demixing at the two-phase region above the LCST was carried out by light scattering.     

Effect of poly(styrene‐co‐maleic anhydride) imidization on the miscibility and phase‐separation temperatures of poly(styrene‐co‐maleic anhydride)/poly(vinyl methyl ether) and poly(styrene‐co‐maleic anhydride)/ poly(methyl methacrylate) blends

The objective of this work was to study the miscibility and phase‐separation temperatures of poly(styrene‐co‐maleic anhydride) (SMA)/poly(vinyl methyl ether) (PVME) and SMA/poly(methyl methacrylate) (PMMA) blends with differential scanning calorimetry and small‐angle light scattering techniques. We focused on the effect of SMA partial imidization with aniline on the miscibility and phase‐separation temperatures of these blends. The SMA imidization reaction led to a partially imidized styrene N‐phenyl succinimide copolymer (SMI) with a degree of conversion of 49% and a decomposition temperature higher than that of SMA by about 20°C. We observed that both SMI/PVME and SMI/PMMA blends had lower critical solution temperature behavior. The imidization of SMA increased the phase‐separation temperature of the SMA/PVME blend and decreased that of the SMA/PMMA blend. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of a filler on the rheological and mechanical properties of the liquid‐crystalline polyester–poly(methyl methacrylate) blends

The rheological and mechanical properties of the blends of liquid‐crystalline polyester (LCP) and poly(methyl methacrylate) (PMMA) filled with aluminum borate whiskers have been studied. It was established the combined action of reinforcing LCP and filler onto the property of PMMA matrix leads to marked reinforcing of PMMA. At 10% of filler and 30% of LCP, the tensile strength of PMMA increases by 30% and elasticity modulus by 110%, the processability being no worse. The viscosity of the blend PMMA + 30% LCP + 10% filler practically is the same as the PMMA melt viscosity at 220°C. With increasing concentration of LCP up to 30%, the filler effect in binary matrix becomes more essential. The possible reason is the preferential adsorption of LCP at the filler interface (surface segregation) and additional ordering of LCP near the surface, possible, due to additional stretching of nematic phase in the convergent flow zone. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 993–999, 2000     

拉曼Mapping成像研究聚苯乙烯/聚甲基丙烯酸甲酯共混体系的相态结构

利用拉曼光谱成像技术研究了聚苯乙烯/聚甲基丙烯酸甲酯（PS/PMMA）共混薄膜体系及其增容体系（增容剂为PS-b-PMMA嵌段共聚物）的相态结构及化学成分分布。实验结果表明,拉曼Mapping成像技术不仅可以得到PS/PMMA共混体系化学成分的精确分布图,同时也可以获取共混体系中分散相、界面相和连续相的分子指纹光谱。研究发现,共混体系中分散相和连续相组分分布与体系的组成紧密相关,当PS/PMMA质量比30/70时,分散相为PS,连续相为PMMA;当PS/PMMA质量比为50/50时,分散相为PS,但PS分子链仍存在于PMMA连续相中;当PS/PMMA质量比为70/30时,分散相为PMMA,连续相为PS。当增容剂PS-b-PMMA加入到PS/PMMA共混体系中后,分散相粒径减小、分布更加均匀、共混体系相容性指数（N_c）增大,说明PS/PMMA共混体系由完全不相容体系趋向变成半相容性体系,这是因为增容剂能增加PS和PMMA之间的相互作用,降低了体系的相分离程度,改善了共混体系的相容性。     

Influence of tacticity of poly(methyl methacrylate) on the compatibility with poly(vinyl phenol)

Isotactic, atactic, and syndiotactic poly(methyl methacrylate) (PMMA) were mixed with poly(vinyl phenol) (PVPh) separately in tetrahydrofuran to make three polymer blend systems. Differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy were used to study the miscibility of these blends. Isotactic PMMA was found to be more miscible with PVPh than atactic or syndiotactic PMMA. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1773–1780, 1997     

Immiscibility–miscibility phase transitions in blends of poly(L‐lactide) with poly(methyl methacrylate)

BACKGROUND: The nature of phase transitions and apparently irreversible phase homogenization upon heating in blends of biodegradable poly(L ‐lactide) (PLLA) with poly(methyl methacrylate) (PMMA) were proven using differential scanning calorimetry, polarized optical microscopy, scanning electron microscopy and ¹H NMR spectroscopy. The complex phase behaviour in this blend system is puzzling and is a matter of debate; this study attempts to clarify the true nature of the phase behaviour. RESULTS: A PMMA/PLLA blend is immiscible at ambient temperature but can become miscible upon heating to higher temperatures with an upper critical solution temperature (UCST) at 230 °C. The blends, upon rapid quenching from the UCST, can be frozen into a quasi‐miscible state. In this state, the interaction strength was determined to be χ₁₂ = ? 0.15 to ? 0.19, indicating relatively weak interactions between the PLLA ester and PMMA acrylic carbonyl groups. CONCLUSION: The absence of chemical exchange reactions above the UCST and phase reversibility back to the original phase separation morphology, assisted by solvent re‐dissolution, in the heat‐homogenized PLLA/PMMA blend was shown. Verification of UCST behaviour, phase diagrams and solvent‐assisted phase reversibility were experimentally demonstrated in PMMA/PLLA blends. Copyright © 2008 Society of Chemical Industry     

Thermal and mechanical properties of poly(methyl methacrylate) and ethylene vinyl acetate copolymer blends

A series of poly(methyl methacrylate) (PMMA) blends have been prepared with different compositions viz., 5, 10, 15, and 20 wt % ethylene vinyl acetate (EVA) copolymer by melt blending method in Haake Rheocord. The effect of different compositions of EVA on the physico‐mechanical and thermal properties of PMMA and EVA copolymer blends have been studied. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and thermogravimetric analysis (TGA) has been employed to investigate the phase behavior of PMMA/EVA blends from the point of view of component specific interactions, molecular motions and morphology. The resulting morphologies of the various blends also studied by optical microscope. The DSC analysis indicates the phase separation between the PMMA matrix and EVA domains. The impact strength analysis revealed a substantial increase in impact strength from 19 to 32 J/m. The TGA analysis reveals the reduction in onset of thermal degradation temperature of PMMA with increase in EVA component of the blend. The optical microscope photographs have demonstrated the PMMA/EVA system had a microphase separated structure consisting of dispersed EVA domains within a continuous PMMA matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

An inelastic electron tunnelling spectroscopy (IETS) study of poly(vinylacetate) poly(methyl methacrylate) and poly(vinylalcohol) adsorbed on aluminium oxide

IETS is used to investigate the adsorption of poly(vinylacetate) (PVA), poly(methylmethacrylate) (PMMA), and poly(vinylalcohol) (PVOH) on aluminium oxide. These polymers are of interest in the field of adhesion science, and until now synthetic macromolecules have not been studied in this way. Both commercially available polymers and those synthesized in our laboratory have been used. On the basis of IET spectra presented here, and existing i.r. spectra it is believed that PMMA and PVA undergo ester cleavage at the oxide surface leading to their subsequent adsorption. For PMMA this is thought to be via carboxylate anions generated on the polymer side groups, while PVA is expected to be adsorbed as PVOH. Bonding of PVOH to the oxide is not fully understood, but may occur by the formation of an AlOC bridge. Another possibility for the above polymers, that of intermolecular hydrogen bonding between polar polymer side groups, and adsorbed hydroxyl species present on the oxide surface, cannot be ruled out.     

Preparation of antibacterial poly(methyl methacrylate) by solution blending with water-insoluble antibacterial agent poly[(tert-buty1amino) ethyl methacrylate]

A simple and effective way was developed to prepare antibacterial poly(methyl methacrylate) (PMMA) materials from commercial PMMA and synthesized poly[2-(tert-butylamino) ethyl methacrylate] (PTBAEMA) by solution blending and solvent evaporation methods. The chemical structure of as-synthesized PTBAEMA was characterized by FTIR and ¹H-NMR, and the molecular weight (M_w) and polydispersity index was determined by Gel Permeation Chromatograph. The two components, that is, PMMA and PTBAEMA, were partially miscible and of regular domain size and shape as revealed by SEM observation. Antibacterial assay revealed PMMA/PTBAEMA blends inherited the good antibacterial activity of PTBAEMA against both Staphylococcus aureus and Escherichia coli, no matter whether the bacteria were waterborne or airborne. Besides, the antibacterial performance of PMMA/PTBAEMA blends depended on the M_w and dosage of PTBAEMA, and type of bacteria strain. Furthermore, it was proved that PMMA/PTBAEMA blends killed bacteria on direct contact without releasing active component, which sufficiently met the demand of developing environment-friendly antibacterial materials. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Morphological and infra-red studies on highly oriented poly(vinylidene fluoride)/poly(methyl methacrylate) blends

Highly oriented melt drawn films of poly(vinylidene fluoride) (PVDF) and blends of poly(vinylidene fluoride) and poly(methyl methacrylate) (PMMA) have been studied by transmission electron microscopy, electron diffraction and infra-red spectroscopy. Infra-red spectra show the second moment of the orientation function for PVDF samples to be greater than 0.94. Using such a sample, the transition dipole directions relative to the chain axis have been calculated. Electron microscopic studies of the PVDF/PMMA blends show a transformation for pure PVDF from a lamellar morphology to a mixture of lamellar and needle-like crystals for the 80/20 blend. The 60/40 blend shows a pure needle-like morphology. The β phase content for this blend is dependent upon the composition and thermal history. An increase in the β phase content is observed with the addition of PMMA. After annealing at 110°C, the 50/50 blend shows a lamellar β phase morphology. A significant increase in the segmental orientation of PVDF is also observed.     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(vinyl pyrrolidone)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMA) (designated iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(vinyl pyrrolidone) (PVP) primarily in chloroform to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PVP. The aPMMA/PVP and sPMMA/PVP blends were found to be miscible because all the prepared films showed composition-dependent glass-transition temperatures (T_g). The glass-transition temperatures of the aPMMA/PVP blends are equal to or lower than weight average and can be qualitatively described by the Gordon–Taylor equation. The glass-transition temperatures of the other miscible blends (i.e., sPMMA/PVP blends) are mostly higher than weight average and can be approximately fitted by the simplified Kwei equation. The iPMMA/PVP blends were found to be immiscible or partially miscible based on the observation of two glass-transition temperatures. The immiscibility is probably attributable to a stronger interaction among isotactic MMA segments because its ordination and molecular packing contribute to form a rigid domain. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3190–3197, 2001     

Viscoelastic properties of blends of poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile) having various acrylonitrile contents

Dynamic viscoelastic properties of blends of poly(methyl methacrylate) (PMMA) and poly(styrene‐co‐acrylonitrile) (SAN) with various AN contents were measured to evaluate the influence of SAN composition, consequently χ parameter, upon the melt rheology. PMMA/SAN blends were miscible and exhibited a terminal flow region characterized by Newtonian flow, when the acrylonitrile (AN) content of SAN ranges from 10 to 27 wt %. Whereas, PMMA/SAN blends were immiscible and exhibited a long time relaxation, when the AN content in SAN is less than several wt % or greater than 30 wt %. Correspondingly, melt rheology of the blends was characterized by the plots of storage modulus G′ against loss modulus G″. Log G′ versus log G″ plots exhibited a straight line of slope 2 for the miscible blends, but did not show a straight line for the immiscible blends because of their long time relaxation mechanism. The plateau modulus, determined as the storage modulus G′ in the plateau zone at the frequency where tan δ is at maximum, varied linearly with the AN content of SAN irrespective of blend miscibility. This result indicates that the additivity rule holds well for the entanglement molecular weights in miscible PMMA/SAN blends. However, the entanglement molecular weights in immiscible blends should have “apparent” values, because the above method to determine the plateau modulus is not applicable for the immiscible blends. Effect of χ parameter on the plateau modulus of the miscible blends could not be found. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Solvent effects on the miscibility of poly(methyl methacrylate)/poly(bisphenol a carbonate) blends

Blends of atactic or syndiotactic poly(methyl methacrylate) (designated as aPMMA or sPMMA) and poly(bisphenol A carbonate) (PC) were prepared from solution casting. Tetrahydrofuran (THF) and chloroform were used as solvent. Experimental results indicated that the as‐cast blends from THF were quite different from the chloroform‐cast ones. After film preparation, THF‐cast blends did not show any visible phase separation. However, chloroform‐cast blends formed a phase‐separated structure. The as‐cast PC from either solvent was not completely amorphous, and had a melting point at 239–242°C, indicating a certain degree of crystallinity. In contrast, the quenched samples of aPMMA/PC blends prepared from the two solvents behaved virtually the same. They both showed aPMMA dissolves better in PC, but PC solubility in aPMMA is very little. Using sPMMA instead of aPMMA to blend with PC, different results were obtained. The quenched sPMMA/PC blends cast from THF showed only one T_g. However, immiscibility (i.e., two T_gs) was found in the same blend system when cast from chloroform. THF was believed to cause the observation of single T_g due to the following kinetic reason. sPMMA and PC were still trapped together even after THF removal in a homogeneous, but nonequilibrium state below the glass transition. Therefore, the quenched sPMMA/PC blends were not truly thermodynamically miscible. From the results of aPMMA or sPMMA with PC, increasing syndiotacticity seemed to improve the miscibility between PMMA and PC. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2842–2850, 2001