Effects of morphologies on acetone-sensing properties of tungsten trioxide nanocrystals

In this work, triclinic WO₃ nanoplates and WO₃ nanoparticles were comparatively investigated as sensing materials to detect acetone vapors. Single-crystalline WO₃ nanoplates with large side-to-thickness ratios were synthesized via a topochemical conversion from tungstate-based inorganic-organic hybrid nanobelts, and the WO₃ nanoparticles were obtained by calcining commercial H₂WO₄ powders at 550 °C. The acetone-sensing properties were evaluated by measuring the change in electrical resistance of the WO₃ sensors before and after exposure to acetone vapors with various concentrations. The WO₃ nanoplate sensors showed a high and stable sensitive response to acetone vapors with a concentration range of 2-1000 ppm, and the sensitivity was up to 42 for 1000 ppm of acetone vapor operating at 300 °C. The response and recovery times were as short as 3-10 s and 12-13 s, respectively, for the WO₃ nanoplate sensors when operating at 300 °C. The acetone-sensing performance of the WO₃ nanoplate sensors was more excellent than that of the WO₃ nanoparticle sensors under a similar operating condition. The enhancement of the WO₃ nanoplate sensors in the acetone-sensing property was attributed to the poriferous textures, single-crystalline microstructures and high surface areas of the aggregates consisting of WO₃ nanoplates, which were more favorable in rapid and efficient diffusion of acetone vapors than the WO₃ nanoparticles.     

Ethanol sensing using CuO/MWNT thin film

Copper (II) oxide (CuO)/multiwall carbon nanotube (MWNT) thin film based ethanol-sensors were fabricated by dispersing CVD-prepared MWNTs in varying concentration over DC magnetron sputtered-CuO films. The responses of these sensors as a function of MWNT concentrations and temperatures were measured, and compared. The sensing response was the maximum at an operating temperature near 400 °C for all the samples irrespective of the MWNTs dispersed over them. At optimum operating temperature (T_opt) of 407 ± 1 °C, the response is linear for 100-700 ppm range and tends to saturate at higher concentrations. In comparison with bare CuO sample, the response of CuO/MWNT sensing films increased up to 50% in the linear range. The response improvement for 2500 ppm of ethanol was up to 90% compared to bare CuO sample. In addition, the sensing response time also reduced to around 23% for lowest ethanol concentration at T_opt. However, a decrease in the sensor response was observed on films with very high concentrations of MWNTs.     

Hydrothermal synthesis of hollow ZnSnO3 microspheres and sensing properties toward butane

Hollow ZnSnO₃ microspheres were successfully prepared by hydrothermal method at 160 °C for 12 h. The prepared material was characterized by field emission scanning electron microscope (FESEM), transmission electron microscope (TEM) and X-ray diffraction measurements (XRD). The average diameter of the hollow ZnSnO₃ microspheres was in the range of 400-600 nm. Compared with solid ZnSnO₃ microspheres structure, the hollow ZnSnO₃ microspheres showed better response (S) to butane. To 500 ppm butane, the sensor response (S) of the hollow ZnSnO₃ microspheres was 5.79 at the optimum operating temperature of 380 °C, and the response and recovery time were 0.3 s and 0.65 s, respectively. The sensitivities of sensors based on this material were linear with the concentration of butane in the range of 100-1000 ppm.     

Selectivity of flame-spray-made Nb/ZnO thick films towards NO2 gas

Unloaded ZnO and Nb/ZnO nanoparticles containing 0.25, 0.5 and 1 mol.% Nb were produced in a single step by flame-spray pyrolysis (FSP) technique. The nanoparticles were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The BET surface area (SSA_BET) of the nanoparticles was measured by nitrogen adsorption. FSP yielded small Nb particles attached to the surface of the supporting ZnO nanoparticles, indicating a high SSA_BET. The morphology and accurate size of the primary particles were further investigated by TEM. Nb/ZnO nanoparticles paste composed of ethyl cellulose and terpineol as binder and solvent respectively was coated on Al₂O₃ substrate interdigitated with gold electrodes to form thick films by spin coating technique. After the sensing tests, the morphology and the cross-section of sensing film were analyzed by SEM and EDS analyses. The influence on a low dynamic range of Nb concentration on NO₂ response (0.1-4 ppm) of thick film sensor elements was studied at the operating temperatures ranging from 250 to 350 °C in the presence of dry air. The optimum Nb concentration was found be 0.5 mol.% and 0.5 mol.% Nb exhibited an optimum NO₂ response of ∼1640 and a short response time (27 s) for NO₂ concentration of 4 ppm at 300 °C.     

Temperature dependent H2S and Cl2 sensing selectivity of Cr2O3 thin films

The conductometric gas sensing characteristics of Cr₂O₃ thin films - prepared by electron-beam deposition of Cr films on quartz substrate followed by oxygen annealing - have been investigated for a host of gases (CH₄, CO, NO₂, Cl₂, NH₃ and H₂S) as a function of operating temperature (between 30 and 300 °C) and gas concentration (1-30 ppm). We demonstrate that these films are highly selective to H₂S at an operating temperature of 100 °C, while at 220 °C the films become selective to Cl₂. This result has been explained on the basis of depletion of chemisorbed oxygen from the surface of films due to temperature and/or interaction with Cl₂/H₂S, which is supported experimentally by carrying out the work function measurements using Kelvin probe method. The temperature dependent selectivity of Cr₂O₃ thin films provides a flexibility to use same film for the sensing of Cl₂ as well as H₂S.     

Gas sensors based on anodic tungsten oxide

Nanostructured porous tungsten oxide materials were synthesized by the means of electrochemical etching (anodization) of tungsten foils in aqueous NaF electrolyte. Formation of the sub-micrometer size mesoporous particles has been achieved by infiltrating the pores with water. The obtained colloidal anodic tungsten oxide dispersions have been used to fabricate resistive WO₃ gas sensors by drop casting the sub-micrometer size mesoporous particles between Pt electrodes on Si/SiO₂ substrate followed by calcination at 400 °C in air for 2 h. The synthesized WO₃ films show slightly nonlinear current-voltage characteristics with strong thermally activated carrier transport behavior measured at temperatures between −20 °C and 280 °C. Gas response measurements carried out in CO, H₂, NO and O₂ analytes (concentration from 1 to 640 ppm) in air as well as in Ar buffers (O₂ only in Ar) exhibited a rapid change of sensor conductance for each gas and showed pronounced response towards H₂ and NO in Ar and air, respectively. The response of the sensors was dependent on temperature and yielded highest values between 170 °C and 220 °C.     

SnO2 thin film sensor with enhanced response for NO2 gas at lower temperatures

Semiconducting SnO₂ thin films having higher value of electrical conductivity have been deposited using RF sputtering technique in the reactive gas environment (30% O₂ + 70% Ar) using a metallic tin (Sn) target for detection of oxidizing NO₂ gas. The effect of growth pressure (12-18 mTorr) on the surface morphology and structural property of SnO₂ film was studied using Atomic force microscopy (AFM), Scanning electron microscopy (SEM) and X-ray Diffraction (XRD) respectively. Film deposited at 16 mTorr sputtering pressure was porous with rough microstructure and exhibits high sensor response (∼2.9 × 10⁴) towards 50 ppm NO₂ gas at a comparatively low operating temperature (∼100 °C). The sensor response was found to increase linearly from 1.31 × 10² to 2.9 × 10⁴ while the response time decrease from 12.4 to 1.6 min with increase in the concentration of NO₂ gas from 1 to 50 ppm. The reaction kinetics of target NO₂ gas on the surface of SnO₂ thin film at the Sn sites play important role in enhancing the response characteristics at lower operating temperature (∼100 °C). The results obtained in the present study are encouraging for realization of SnO₂ thin film based sensor for efficient detection of NO₂ gas with low power consumption.     

Enhanced room temperature response of SnO2 thin film sensor loaded with Pt catalyst clusters under UV radiation for LPG

The room temperature response characteristics of SnO₂ thin film sensor loaded with platinum catalyst clusters are investigated for LPG under the exposure of ultraviolet radiation. The SnO₂-Pt cluster sensor structures have been prepared using rf sputtering. Combined effect of UV radiation exposure (λ = 365 nm) and presence of Pt catalyst clusters (10 nm thick) on SnO₂ thin film sensor surface is seen to lead to an enhanced response (4.4 × 10³) for the detection of LPG (200 ppm) at room temperature whereas in the absence of UV illumination a comparable response (∼5 × 10³) could be obtained but only at an elevated temperature of 220 °C. The present study therefore investigates the effect of UV illumination on LPG sensing characteristics of SnO₂ sensors loaded with Pt clusters of varying thickness values. Results indicate the possibility of utilizing the sensor structure with novel dispersal of Pt catalyst clusters on SnO₂ film surface for efficient detection of LPG at room temperature under the illumination of UV radiations.     

Highly sensitive and selective LPG sensor based on α-Fe2O3 nanorods

The α-Fe₂O₃ nanorods were successfully synthesized without any templates by calcining the α-FeOOH precursor in air at 300 °C for 2 h and their LPG sensing characteristics were investigated. The α-FeOOH precursor was prepared through a simple and low cost wet chemical route at low temperature (40 °C) using FeSO₄·7H₂O and CH₃COONa as starting materials. The formation of α-FeOOH precursor and its topotactic transformation to α-Fe₂O₃ upon calcination was confirmed by X-ray diffraction measurement (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) analysis. The α-Fe₂O₃ nanorods exhibited outstanding gas sensing characteristics such as, higher gas response (∼1746-50 ppm LPG at 300 °C), extremely rapid response (∼3-4 s), relatively slow recovery (∼8-9 min), excellent repeatability, good selectivity and lower operating temperature (∼300 °C). Furthermore, the α-Fe₂O₃ nanorods are able to detect up to 5 ppm for LPG with reasonable response (∼15) at the operating temperature of 300 °C and they can be reliably used to monitor the concentration of LPG over the range (5-60 ppm). The experimental results clearly demonstrate the potential of using the α-Fe₂O₃ nanorods as sensing material in the fabrication of LPG sensors. Plausible LP G sensing mechanism of the α-Fe₂O₃ nanorods is also discussed.     

Facile synthesis of hierarchical SnO2 semiconductor microspheres for gas sensor application

Hierarchical SnO₂ microspheres were synthesized by a hydrothermal method at 140 °C using stannic chloride hydrate and sodium hydroxide as starting materials. The individual hierarchical SnO₂ microsphere ranged from 700 to 900 nm in diameter. After these microspheres were heated at 600 °C for 2 h, the spheres were cross-linked into clusters by short SnO₂ nanorods as revealed by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Most importantly, SnO₂ hierarchical microsphere sensor exhibits excellent selectivity and fast response to ethanol. Response and recovery times were 0.6 s and 11 s when the sensor was exposed to 50 ppm ethanol at an operating temperature of 300 °C. Thus, hierarchical structures play a significant role in the field of gas sensing.     

Fabrication of N-type Fe2O3 and P-type LaFeO3 nanobelts by electrospinning and determination of gas-sensing properties

N-type Fe₂O₃ nanobelts and P-type LaFeO₃ nanobelts were prepared by electrospinning. The structure and micro-morphology of the materials were characterized by X-ray diffraction (XRD) and scanning of electron microscopy (SEM). The gas sensing properties of the materials were investigated. The results show that the optimum operating temperature of the gas sensors fabricated from Fe₂O₃ nanobelts is 285 °C, whereas that from LaFeO₃ nanobelts is 170 °C. Under optimum operating temperatures at 500 ppm ethanol, the response of the gas sensors based on these two materials is 4.9 and 8.9, respectively. The response of LaFeO₃-based gas sensors behaves linearly with the ethanol concentration at 10-200 ppm. Sensitivities to different gases were examined, and the results show that LaFeO₃ nanobelts exhibit good selectivity to ethanol, making them promising candidates as practical detectors of ethanol.     

Ag nanoparticles modified TiO2 spherical heterostructures with enhanced gas-sensing performance

Monodispersed TiO₂ spherical colloids with diameters of about 250 nm were prepared by a sol-gel method. Heterostructural Ag-TiO₂ spheres were manipulated by surface engineering, in which the Ag nanoparticles with an average size of 10 nm were uniformly distributed on the surface of the TiO₂ nanospheres by in situ reduction and growth. The gas-sensing properties of the TiO₂ nanospheres and heterostructural Ag-TiO₂ nanospheres to ethanol and acetone were measured at 350 °C. The results indicated that Ag nanoparticles greatly enhanced the response, stability and response characteristic of TiO₂ nanospheres to the tested gases. Response times of Ag-TiO₂ sensor to 30 ppm acetone and 50 ppm ethanol were <5 s.     

Synthesis and characterisation of nanosized TiO2-ZrO2 binary system prepared by an aqueous sol-gel process: Physical and sensing properties

Nanostructured TiO₂-ZrO₂ thin films and powders were prepared by a straightforward aqueous particulate sol-gel route. Titanium (IV) isopropoxide and zirconium (IV) acetate hydrate were used as precursors, and hydroxypropyl cellulose was used as a polymeric fugitive agent in order to increase the specific surface area. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy revealed that the powder were crystallised at the low temperature of 500 °C, containing anatase-TiO₂ and tetragonal-ZrO₂ phases. Furthermore, it was found that ZrO₂ retarded the anatase-to-rutile transformation up to 900 °C. The activation energies for crystallite growth of TiO₂ and ZrO₂ components in the binary system were calculated 10.16 and 3.12 kJ/mol, respectively. Transmission electron microscope (TEM) image showed that one of the smallest crystallite sizes was obtained for TiO₂-ZrO₂ binary mixed oxide, being 5 nm at 500 °C. Field emission scanning electron microscope (FESEM) analysis revealed that the deposited thin films had nanostructured morphology with the average grain size of 20 nm at 500 °C and 36 nm at 900 °C. Thin films produced under optimised conditions showed excellent microstructural properties for gas sensing applications. They exhibited a remarkable response towards low concentrations of CO and NO₂ gases at low operating temperature of 150 °C, resulted in an increase of thermal stability of sensing films as well as a decrease in the power consumption. Furthermore, calibration curves revealed that TiO₂-ZrO₂ sensor follows the power law, S = A[gas]^B (where S is sensor response, coefficients A and B are constants and [gas] is gas concentration) for the two types of gases, and it has excellent capability for the detection of low gas concentrations.     

Gas sensing properties at room temperature of a quartz crystal microbalance coated with ZnO nanorods

Gas sensors based on a quartz crystal microbalance (QCM) coated with ZnO nanorods were developed for detection of NH₃ at room temperature. Vertically well-aligned ZnO nanorods were synthesized by a novel wet chemical route at a low temperature of 90 °C, which was used to grow the ZnO nanorods directly on the QCM for the gas sensor application. The morphology of the ZnO nanorods was examined by field-emission scanning electron microscopy (FE-SEM). The diameter and length of the nanorods were 100 nm and 3 μm, respectively. The QCM coated with the ZnO nanorods gas sensor showed excellent performance to NH₃ gas. The frequency shift (Δf) to 50 ppm NH₃ at room temperature was about 9.1 Hz. It was found that the response and recovery times were varied with the ammonia concentration. The fabricated gas sensors showed good reproducibility and high stability. Moreover, the sensor showed a high selectivity to ammoniac gas over liquefied petroleum gas (LPG), nitrous oxide (N₂O), carbon monoxide (CO), nitrogen dioxide (NO₂), and carbon dioxide (CO₂).     

Effect of thickness of platinum catalyst clusters on response of SnO2 thin film sensor for LPG

This paper reports the sensing response characteristics of rf-sputtered SnO₂ thin films (90 nm thick) loaded with platinum catalyst cluster of varying thickness (2-20 nm) for LPG detection. The enhanced response (5 × 10³) was obtained for 200 ppm LPG with the presence of 10 nm thin and uniformly distributed Pt catalyst clusters on the surface of SnO₂ thin film at a relatively low operating temperature (220 °C). The high response for LPG is shown to be primarily due to the enhanced catalytic activity for adsorbed oxygen on the surface of SnO₂ thin film besides the spill over mechanism at elevated temperature.     

WO3 nanocrystals: Synthesis and application in highly sensitive detection of acetone

WO₃ nanocrystals have been prepared by a sol-gel route and characterized by X-ray diffractometry, scanning electron microscopy, and transmission electron microscopy. The experimental results show that WO₃ nanocrystals have a high crystallographic quality and a good dispersivity. The particles’ sizes are in the range of 25-100 nm. The fabricated WO₃ nanocrystal-based sensors have an excellent sensitivity and selectivity to acetone, and display a rapid response and recovery characteristics. The developed sensors exhibit a detection limit down to 0.05 ppm at 300 °C, rendering a promising application in noninvasive diagnosis of diabetes. The response mechanism of the WO₃ nanocrystal sensor to low concentration of acetone has been discussed based on the depletion layer model.     

Electrospun Cu-doped ZnO nanofibers for H2S sensing

Pure and Cu-doped ZnO nanofibers were synthesized via electrospinning technology. The morphology and structure of the as-synthesized nanofibers were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and Raman spectroscopy. The effects of Cu doping on H₂S sensing properties at low concentration (1-10 ppm) were investigated at 230 °C. The results show that the H₂S sensing properties of ZnO nanofibers are effectively improved by Cu doping: 6 at% Cu-doped ZnO nanofibers show a maximum sensitivity to H₂S gas, and the response to 10 ppm H₂S is one order of magnitude higher than the one of pure ZnO nanofibers.     

Acetylene sensor based on Pt/ZnO thick films as prepared by flame spray pyrolysis

ZnO nanoparticles loaded with 0.2-2.0 at.% Pt have been successfully produced in a single step by flame spray pyrolysis (FSP) technique using zinc naphthenate and platinum(II) acetylacetonate, as precursors dissolved in xylene and their acetylene sensing characteristics have been investigated. The particle properties were analyzed by XRD, BET, TEM, SEM and EDS. Under the 5/5 (precursor/oxygen) flame condition, ZnO nanoparticles and nanorods were observed. The crystallite sizes of ZnO spherical and hexagonal particles were found to be ranging from 5 to 20 nm while ZnO nanorods were seen to be 5-20 nm in width and 20-40 nm in length. In addition, very fine Pt nanoparticles with diameter of ∼1 nm were uniformly deposited on the surface of ZnO particles. From gas-sensing characterization, acetylene sensing characteristics of ZnO nanoparticles is significantly improved as Pt content increased from 0 to 2  at.%. The 2 at.% Pt loaded ZnO sensing film showed an optimum C₂H₂ response of ∼836 at 1% acetylene concentration and 300 °C operating temperature. A low detection limit of 50 ppm was obtained at 300 °C operating temperature. In addition, Pt loaded ZnO sensing films exhibited good selectivity towards hydrogen, methane and carbon monoxide.     

Gas sensing properties of p-type hollow NiO hemispheres prepared by polymeric colloidal templating method

This work presents a simple and versatile route to produce macroporous p-type metal oxide thin films. Two-dimensional arrays of p-type NiO films with a hollow hemisphere structure were fabricated by colloidal templating and RF-sputtering followed by a subsequent heat treatment. The diameter and shell thickness of the NiO hemisphere were 800 nm and 20 nm, respectively. X-ray diffraction and high-resolution transmission electron microscopy analysis indicate that the pure NiO phase with grain size of 10 nm was obtained at calcination temperatures that exceeded 450 °C. Close-packed arrays of hollow NiO hemispheres were found to exhibit p-type gas sensing properties against (CO, H₂, C₃H₈, CH₄, NO₂, and C₂H₅OH), leading to significantly enhanced responses to C₂H₅OH (R_gas/R_air = 5.0 at 200 ppm).     

Enhanced ammonia sensing performances of Pd-sensitized flowerlike ZnO nanostructure

We report the synthesis of flowerlike ZnO nanostructure using a facile hydrothermal process, and the investigation on the ammonia (NH₃)-sensing properties of the pure and palladium (Pd)-sensitized flowerlike ZnO nanostructure. The phase purity, morphology, and structure of the pure and Pd-sensitized ZnO nanostructure are investigated. The characterized results reveal that the flowerlike ZnO has a wurtzite structure and is composed of numerous aggregated single-crystalline ZnO nanorods with a diameter of about 60 nm. Having fabricated gas sensors based on the pure and Pd-sensitized flowerlike ZnO, we find that the Pd-sensitized sensor exhibits a response of 45.7-50 ppm NH₃ at 210 °C, which is about 8 times higher than that of pure ZnO at the optimal operating temperature of 350 °C. The enhanced NH₃-sensing performance demonstrates that the significant decrease in optimal operating temperature and the distinct increase in response are attributed to the sensitization effect of Pd.