Grafting vinyl monomers onto polyester fibers. III. Graft copolymerization of methyl methacrylate onto poly(ethylene terephthalate) using potassium permanganate–oxalic acid redox system

The use of the KMnO₄—oxalic acid redox system to initiate graft copolymerization of methyl methacrylate (MMA) onto poly(ethylene terephthalate) (PET) fiber has been investigated. The rate of grafting was determined by varying the concentrations of monomer, KMnO₄, oxalic acid, acidity of the medium, and temperature. The graft yield increases steadily with increasing KMnO₄ concentration. The graft yield is also influenced with concentration. The graft yield is also influenced with temperature. The effect of certain solvents on the rate of grafting has been investigated, and a suitable reaction mechanism has been proposed.     

Grafting of acrylic acid onto flax fibers using Mn(IV)‐citric acid redox system

When the flax fibers (machine tow) were treated with KMnO₄ solution, MnO₂ was deposited over‐all the fiber surface. The amount of MnO₂ deposited relied on the KMnO₄ concentration. Subjecting the flax‐containing MnO₂ to a solution consisting of monomer (acrylic acid, AA) and citric acid, CA (or any acid used in this work) resulted in formation of poly(AA)‐flax graft copolymer. Dependence of the polymer criteria, namely, the total percentage conversion (%TC) and the carboxyl content of the grafted flax fibers on various grafting parameters, viz., concentrations of the redox pair as well as AA, material‐to‐liquor ratio (M/R), duration and temperature of polymerization, kind of the acid and kind of the flax fibers pretreatment was studied systematically. The results indicated that the polymerizability of AA molecules, expressed as %TC (i.e., counting both grafting and homopolymerization) and thence the carboxyl content (i.e., evaluating the extent of AA grafting along the flax backbone) was optimized with the following conditions: [AA], 100% (based on weight of flax fibers, owf); [CA], 0.4 meq/1 g flax; [MnO₂], 0.4 meq/1 g flax; polymerization temperature, 40°C; polymerization time, 30 min; and the M/R, 1 : 50. A tentative mechanism for grafting of flax fibers with AA using MnO₂‐acid redox system was elucidated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3028–3036, 2006     

Graft copolymers of starch with mineral acid salts of dimethylaminoethyl methacrylate. Preparation and testing as flocculating agents

Mineral acid salts of dimethylaminoethyl methacrylate (DMAEMA) have been graft polymerized onto starch with ferrous ammonium sulfate–hydrogen peroxide initiation. The nitric acid salt was used in most reactions, and graft polymerizations were run in both water and aqueous–organic solvent systems. Increased monomer concentration in water led to an increase in both the percentage of poly(DMAEMA · HNO₃) in the graft copolymer (percent add-on) and the molecular weight of grafted branches. Variations in initiator concentration altered the percent add-on only slightly but affected the molecular weight of grafted polymer significantly. When swollen starch, in contrast with unswollen starch was used in graft polymerization reactions run in water, the product had a higher per cent add-on and a larger number of grafted branches of lower molecular weight. The efficiency of starch–poly(DMAEMA · HNO₃) graft copolymers as flocculants for diatomaceous silica increased with per cent add-on; however, variations in grafting frequency and graft molecular weight had less effect on the behavior of these materials as flocculants.     

Modification of carbohydrate polymers via grafting of methacrylonitrile onto pregelled starch using potassium monopersulfate/Fe2+ redox pair

The graft copolymerization of reactive pregelled starch (PGS) with methacrylonitrile (MAN) was performed and the reaction conditions were optimized using potassium monopersulfate (PMPS) in the presence of ferrous ion redox pair as initiator. Emphasis was directed towards increasing the graft formation and decreasing homopolymerization. The grafting parameters were studied with respect to graft yield and graft reaction efficiency percent. In addition, the newly prepared polymethacrylonitrile (polyMAN)‐pregelled starch graft copolymers were applied to cotton textiles to see their suitability as a new sizing agent. Based on the results obtained, appropriate conditions for grafting MAN onto pregelled starch was established and the graft yield was higher under the following conditions: using 0.004 mol l^?1 potassium monopersulfate as initiator, 0.005 mol l^?1 ferrous ion concentration, 0.003 mol l^?1, sulfuric acid, 50 % MAN concentration (based on weight of substrate), material to liquor ratio 1:2.5, reaction time 60 min, and polymerization temperature 40 °C. Finally, fabric samples sized with polyMAN‐pregelled starch graft copolymers acquired higher tensile strength and abrasion resistance than that sized with original pregelled starch, while elongation at break was unaltered. Copyright © 2004 Society of Chemical Industry     

Removal of basic dyes from aqueous solutions using starch‐graft‐acrylic acid copolymers

Graft copolymerization of acrylic acid (AA) onto starch was carried out with ceric ammonium nitrate as initiator under nitrogen atmosphere. The grafting percentages (GP%) of starch‐graft‐AA (St‐gr‐AA) copolymers were determined. When the AA molar concentrations were 0.3 and 0.5 mol/L, GP% of St‐gr‐AA copolymers were 10.5% (St‐gr‐AA‐1) and 14% (St‐gr‐AA‐2), respectively. St‐gr‐AA copolymers have been used for the adsorption of basic dye (Safranine T) from aqueous solutions. Effects of various parameters such as treatment time, initial pH of the solution (pH = 2–6), initial dye concentration (50– 500 mg/L), and GP% of starch graft copolymers were investigated.Basic dye removal capacities of the copolymers increase along with the augment of initial concentration of the adsorbate, GP% of the copolymers, and pH. The adsorption capacities for St‐gr‐AA‐1 and St‐gr‐AA‐2 reach 116.5 and 204 mg/g, respectively. Equilibrium adsorption data were obtained and fitted very well to Freundlich model. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Ammonia adsorption behavior of polypropylene nonwoven fabric grafted with acrylic acid

An attempt was made to synthesize an adsorbent by the photoinduced grafting of acrylic acid (AA) onto polypropylene nonwoven fabrics using benzophenone (BP) as a photosensitizer in a CH₃OH/H₂O medium. As the BP concentration was increased, the graft yield was increased up to a specific value and then decreased, and the effect of AA concentration showed the same tendency. It was also found that the graft yield increased with the reaction time and temperature. The amounts of ammonia adsorbed onto polypropylene nonwoven fabrics grafted with AA (PP‐g‐AA) were dependent on the graft yield, adsorption time, and ammonia gas pressure. The adsorption capacity of PP‐g‐AA was 5.86 mmol/g at the graft yield of 116.6%, which was much higher than that of active carbon or silica gel. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 295–301, 2002; DOI 10.1002/app.10328     

Grafting vinyl monomers onto silk fibers. VIII. Graft copolymerization of methyl methacrylate onto silk using tetravalent manganese–oxalic acid redox system

The graft copolymerization of methyl methacrylate onto silk fibers was investigated in aqueous solution using the Mn(IV)–oxalic acid redox system. The copolymerization reaction was carried out under a variety of conditions such as different monomer, initiator, oxalic acid, acid concentrations, and temperatures. The graft yield increases with increasing initiator concentration up to 5 × 10^?2M, and with further increase of the initiator concentration it decreases. The graft yield also increases with increasing sulfuric acid concentration up to 15 × 10^?2M, and decreases thereafter. The rate of grafting also increases with increase in oxalic acid concentration up to 1.5 × 10^?2M and 84.592 × 10^?2M, respectively, and thereafter the rate of grafting shows down. The effect of temperature, solvents, and salts on graft yield has also been investigated and a plausible rate expression has been derived.     

Synthesis and characterization of butyl acrylate graft sodium salt of partially carboxymethylated starch

Graft copolymers were synthesized by graft copolymerization of butyl acrylate (BA) onto sodium salt of partially carboxymethylated starch (Na‐PCMS). Ceric ammonium nitrate (CAN), a redox initiator, was used for initiation of graft copolymerization reaction. All the experiments were run with Na‐PCMS having degree of substitution, DS = 0.35. The grafting reaction was characterized by parameters such as % total conversion (%Ct), % grafting (%G), % grafting efficiency (%GE), and % add‐on. Graft copolymers were characterized by infrared spectral analysis and scanning electron microscopy. Variables affecting graft copolymerization reaction such as nitric acid concentration, reaction time, reaction temperature, and ceric ion concentration were investigated. The results revealed that 0.3M CAN as initiator, 0.3M HNO₃, with reaction time 4–4.5 h at 25–30°C were found as suitable parameters for maximum yield of graft copolymerization reaction. © 2006 Wiley Periodicals, Inc. JAppl Polym Sci 102: 3334–3340, 2006     

Graft polymerization of vinyl acetate onto starch. Saponification to starch–g–poly(vinyl alcohol)

Graft polymerizations of vinyl acetate onto granular corn starch were initiated by cobalt-60 irradiation of starch-monomer-water mixtures, and ungrafted poly(vinylacetate) was separated from the graft copolymer by benzene extraction. Conversions of monomer to polymer were quantitative at a radiation dose of 1.0 Mrad. However, over half of the polymer was present as ungrafted poly-(vinyl acetate) (grafting efficiency less than 50%), and the graft copolymer contained only 34% grafted synthetic polymer (34% add-on). Lower irradiation doses produced lower conversions of monomer to polymer and gave graft copolymers with lower % add-on. Addition of minor amounts of acrylamide, methyl acrylate, and methacrylic acid as comonomers produced only small increases in % add-on and grafting efficiency. However, grafting efficiency was increased to 70% when a monomer mixture containing about 10% methyl methacrylate was used. Grafting efficiency could be increased to over 90% if the graft polymerization of vinyl acetate-methyl methacrylate was carried out near 0°C, although conversion of monomers to polymer was low and grafted polymer contained 40-50% poly(methyl methacrylate). Selected graft copolymers were treated with methanolic sodium hydroxide to convert starch–g–poly(vinyl acetate) to starch–g–poly(vinyl alcohol). The molecular weight of the poly(vinyl alcohol) moiety was about 30,000. The solubility of starch–g–poly(vinyl alcohol) in hot water was less than 50%; however, solubility could be increased by substituting either acid-modified or hypochlorite-oxidized starch for unmodified starch in the graft polymerization reaction. Vinyl acetate was also graft polymerized onto acid-modified starch which had been dispersed and partially solubilized by heating in water. A total irradiation dose of either 1.0 or 0.5 Mrad gave starch–g–poly(vinyl acetate) with about 35% add-on, and a grafting efficiency of about 40% was obtained. A film cast from a starch–g–poly(vinyl alcohol) copolymer in which homopolymer was not removed exhibited a higher ultimate tensile strength than a comparable physical mixture of starch and poly(vinyl alcohol).     

Starch–acrylics graft copolymers and blends: Synthesis,characterization, and applications as matrix for drug delivery

A series of acrylic monomers–starch graft copolymers were prepared by ceric ion initiation method by varying the amount of monomers. These graft copolymers were characterized by IR and ¹³C‐NMR spectroscopy. It was seen that as the concentration of monomer [acrylic acid (AA), methacrylic acid (MA), and methyl methacrylate (MMA)] increased the percent add‐on increased in all the graft copolymers, whereas grafting efficiency increased initially but showed a slight decrease with further increase in the monomer concentration (except for MMA). The release rate of paracetamol as a model drug from graft copolymers as well as their blends was studied at two different pH, 1.2 and 7.4, spectrophotometrically. The release of paracetamol in phosphate buffer solution at pH 1.2 was insignificant in the first 3 h for St‐g‐PAA‐ and St‐g‐PMA‐graft copolymers, which was attributed to the matrix compaction and stabilization through hydrogen bonding at lower pH. At pH 7.4, the release rate was seen to decrease with increase in add‐on. The tablet containing poly(methyl methacrylate) (PMMA) did not disintegrate at the end of 30–32 h, which may be attributed to the hydrophobic nature of PMMA. These results indicate that the graft copolymers may be useful to overcome the harsh environment of the stomach and can be used as excipients in colon‐targeting matrices. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Latexes of starch-based graft polymers containing polymerized acrylonitrile

The scope of graft reactions to produce starch-based latexes was extended by graft polymerization of acrylonitrile (AN) onto gelatinized cationic starch possessing quaternary amine functionality and by graft terpolymerization of AN and t-butylaminoethyl methacrylate (TBAEM) onto gelatinized starch by cerium (IV) initiation at 25°C. Grafting onto starches containing highly basic quaternary amines gave polyacrylonitrile [poly(AN)] grafts having about one fourth the number-average molecular weight (M?_n) (178,000–232,000) of those produced by grafting AN onto starches containing the less basic tertiary amine groups. Sonification at 20 KHz of graft polymerization reaction mixtures having up to 8% solids reduced viscosities from 400–3000 cP to 10–40 cP. Diameters of dried particles measured about 300–1500 Å. Shaker-type agitation during grafting onto starch having quaternary amine groups produced poly(AN) chains with lower M?_n values than those produced during blade stirrer-type agitation. M?_n values of grafted poly(AN) decreased with increasing reaction time, degree of substitution of amine in the starch, gelation time of cationic starch at 95°C, and cerium (IV) concentration. AN was copolymerized with TBAEM at molar ratios of 14–85:1 in grafting onto gelatinized starch to yield copolymer side-chain grafts analyzing 8–52:1 of polymerized AN to TBAEM moieties.     

A study on graft copolymerization of methyl methacrylate onto jute fiber

A kinetic study of the graft copolymerization of methyl methacrylate onto jute fiber using KMnO₄–malonic acid redox initiator system has been made. Effects of the concentrations of malonic acid, monomer, and KMnO₄ on graft yield have been studied. Besides, the effects of temperature, acid, and reaction medium, some inorganic salts on graft yield have been investigated. The most remarkable features of the investigation include the proposition of a mechanism, derivation of rate expression for the grafting process, and characterization of the grafted fiber by thermogravimetric analysis.     

Graft copolymers of starch with mixtures of acrylamide and the nitric acid salt of dimethylaminoethyl methacrylate

Mixtures of acrylamide and the nitric acid salt of dimethylaminoethyl methacrylate (DMAEMA·HNO₃) have been graft polymerized onto unmodified wheat starch with ferrous ammonium sulfate–hydrogen peroxide initiation. Graft polymerizations were carried out with both unswollen starch granules and granules that had been swollen by heating in water to 60°C. Ungrafted synthetic polymers were removed from graft copolymers by cold-water extraction and were characterized by their M?_n and DMAEMA·HNO₃ content. Graft copolymers were characterized with respect to per cent add-on, M?_n and DMAEMA·HNO₃ content of grafted polymer, and grafting frequency. Ungrafted synthetic polymers contained a mole percentage of DMAEMA·HNO₃ equal to or greater than that present in the initial monomer mixtures; whereas in most grafted polymers the mole-% DMAEMA·HNO₃ in the grafted branches was less than that in the starting monomers. At all monomer ratios examined, polymer grafted to swollen starch granules contained a higher percentage of DMAEMA·HNO₃ then polymer grafted to unswollen starch. The influence of starch granule swelling on the molecular weight and frequency of grafted branches was correlated with the composition of the initial monomer mixture. It was determined that the effect of granule swelling on graft copolymer structure would be minimal when 25–30 mole-% DMAEMA·HNO₃ was used. In an acetonitrile–water solvent system, reactions with 20 and 50 mole-% DMAEMA·HNO₃ produced graft copolymers with less DMAEMA·HNO₃ in grafted branches than corresponding graft polymerizations run in water. The flocculation of 3% aqueous suspensions of diatomaceous silica was examined with selected starch graft copolymers.     

Graft copolymerization of p‐acryloyloxybenzoic acid and p‐methacryloyloxybenzoic acid onto isotactic polypropylene and their thermal properties: Part I

The polymerization and grafting of the monomers p‐acryloyloxybenzoic acid and p‐methacryloyloxybenzoic acid were studied. Poly(acryloyloxybenzoic acid) was obtained by γ‐radiation‐induced solution polymerization and bulk melt polymerization initiated by dicumyl peroxide. Poly(methacryloyloxybenzoic acid) could be obtained only by bulk melt polymerization. The graft copolymerization of the monomers onto isotactic polypropylene was carried out in bulk. The maximum grafting was reached in shorter times at higher temperatures, and it also increased with the concentration of the monomers in the reaction medium. The thermal and crystallization behavior of the graft copolymers was studied with differential scanning calorimetry and wide‐angle X‐ray diffraction. The graft copolymerization of p‐acryloyloxybenzoic acid did not have any influence on the formation of both α forms (monoclinic) of polypropylene, whereas p‐methacryloyloxybenzoic acid led to the α₂ form. The β‐crystalline modification (hexagonal) formed in poly(acryloyloxybenzoic acid)‐g‐polypropylene products at 185°C and at higher grafting temperatures and also in the second run of differential scanning calorimetry studies after fast cooling. The β form was not observed in graft copolymers of poly(methacryloyloxybenzoic acid). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Radiation Graft Co-polymerization of Methacrylic Acid (MAA) onto Sago Starch Films

Abstract

In this work, the factors that may affect the gamma radiation-induced grafting of methacrylic acid monomer (MAA) onto sago starch films were investigated. The graft copolymers were characterized by tensile mechanical testing, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and infrared spectroscopy. The results showed that the highest grafting yield was obtained within the irradiation dosage level of 10–20 kGy and by using monomer concentration range of 15–20 wt%. The highest tensile mechanical properties were observed for sago starch films having 66% graft yield of MAA. The DSC thermograms indicated a decrease in the gelatinization temperature (temperature at which the disruption of the molecular orders in the starch granules occurs) of sago starch as a result of grafting. This behavior was explained on the basis that radiation grafting prevents the retrograddation process of starch (starch re-crystallization). On the other hand, the IR spectra indicate an increase in the intensity of the absorption band due to C?O stretching, confirming the occurrence of grafted chains of MAA.     

Competitive removal of nickel (II), cobalt (II), and zinc (II) ions from aqueous solutions by starch‐graft‐acrylic acid copolymers

Graft copolymerization of acrylic acid (AA) onto starch was carried out with ceric ammonium nitrate as initiator under nitrogen atmosphere. The grafting percentages (GP%) of starch‐graft‐acrylic acid (St‐g‐AA) copolymers were determined. The effect of GP% of St‐g‐AA copolymers on the competitive removal of Co²⁺, Ni²⁺, Zn²⁺ ions from aqueous solution was investigated at different pH (2, 4, 6). The concentrations of each ion in aqueous solution 5 mmol/L. Effects of various parameters such as treatment time, initial pH of the solution and grafting percentage of starch graft copolymers were investigated. Metal ion removal capacities of St‐g‐AA copolymers increased with GP% of the copolymers and pH. The results show that the removal of metal ions followed as given in the order Co²⁺ > Ni²⁺ > Zn²⁺. In this study, metal ion removal capacities were determined by atomic absorption spectrophotometer (AAS). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Graft copolymerization of methyl acrylate onto sago starch using ceric ammonium nitrate as an initiator

The graft copolymerization of methyl acrylate onto sago starch was carried out by a free radical initiating process. The free radicals were produced by the chemical initiation method in which ceric ammonium nitrate was used as an initiator. It was found that the percentages of grafting, grafting efficiency, and rate of grafting were all dependent on the concentration of ceric ammonium nitrate (CAN), methyl acrylate (MA), sago starch (AGU), mineral acid (H₂SO₄), and reaction temperature and period. The variables affecting the graft copolymerization were thoroughly examined. The optimum yield of grafting was obtained when the concentration of CAN, MA, AGU, and H₂SO₄ were used at 8.77 × 10⁻³, 0.803, 0.135, and 0.175 mol L⁻¹, respectively. The optimum reaction temperature and period were 50°C and 60 min, respectively. The rate of graft polymerization was explored on the basis of experimental results and reaction mechanism. The evidence of grafted copolymers was investigated by using FTIR spectroscopy, TG, and DSC analysis. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 516–523, 2000     

Grafting of acrylamide onto guar gum using KMNO4/oxalic acid redox system

The grafting of acrylamide onto guar gum in aqueous medium initiated by KMnO₄/oxalic acid redox system has been studied gravimetrically at the temperature 35 ± 0.2°C. The effect of redox components, acrylamide concentration and quantity of guar gum has been studied in terms of percentage and efficiency of grafting. A plausible mechanism of grafting and a suitable rate expression has been suggested. The rate of grafting was found to increase with increase in temperature and concentrations of redox components and acrylamide, but, at high concentration of guar gum, the rate was found to decrease.     

Graft copolymerization of acrylic acid onto guar gum

The graft copolymerization of acrylic acid (AA) onto guar gum (GOH) was carried out by a peroxydiphosphate (PDP)–silver(I) system. Grafting ratio, efficiency, add‐on, and conversion increase upon increasing the concentration of PDP and acrylic acid, whereas they decrease upon increasing the concentration of guar gum. Upon increasing the concentration of silver and hydrogen ions up to 2.0 × 10⁻³ and 4.87 × 10⁻² mol dm⁻³, respectively, the grafting ratio and efficiency increase but decrease upon further increasing the concentration. The increase in temperature from 30 to 45°C increases the grafting ratio but the conversion efficiency decreases. The optimum time period for graft copolymerization was found to be 2 h. The graft copolymers were characterized by infrared spectroscopy and thermogravimetric analysis. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 39–44, 2000     

Grafting of poly(3‐hydroxyalkanoate) and linoleic acid onto chitosan

Poly(3‐hydroxy octanoate) (PHO), poly(3‐hydroxy butyrate‐co‐3‐hydroxyvalerate) (PHBV), and linoleic acid were grafted onto chitosan via condensation reactions between carboxylic acids and amine groups. Unreacted PHAs and linoleic acid were eliminated via chloroform extraction and for elimination of unreacted chitosan were used 2 wt % of HOAc solution. The pure chitosan graft copolymers were isolated and then characterized by FTIR, ¹³C‐NMR (in solid state), DSC, and TGA. Microbial polyester percentage grafted onto chitosan backbone was varying from 7 to 52 wt % as a function of molecular weight of PHAs, namely as a function of steric effect. Solubility tests were also performed. Graft copolymers were soluble, partially soluble or insoluble in 2 wt % of HOAc depending on the amount of free primary amine groups on chitosan backbone or degree of grafting percent. Thermal analysis of PHO‐g‐Chitosan graft copolymers indicated that the plastizer effect of PHO by means that they showed melting transitions T_ms at 80, 100, and 113°C or a broad T_ms between 60.5–124.5°C and 75–125°C while pure chitosan showed a sharp T_m at 123°C. In comparison of the solubility and thermal properties of graft copolymers, linoleic acid derivatives of chitosan were used. Thus, the grafting of poly(3‐hydroxyalkanoate) and linoleic acid onto chitosan decrease the thermal stability of chitosan backbone. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103:81–89, 2007