Urchin‐Like CoSe2 as a High‐Performance Anode Material for Sodium‐Ion Batteries

Urchin‐like CoSe₂ assembled by nanorods has been synthesized via simple solvothermal route and has been first applied as an anode material for sodium‐ion batteries (SIBs) with ether‐based electrolytes. The CoSe₂ delivers excellent sodiation and desodiation properties when using 1 m NaCF₃SO₃ in diethyleneglycol dimethylether as an electrolyte and cycling between 0.5 and 3.0 V. A high discharge capacity of 0.410 Ah g^?1 is obtained at 1 A g^?1 after 1800 cycles, corresponding to a capacity retention of 98.6% calculated from the 30th cycle. Even at an ultrahigh rate of 50 A g^?1, the capacity still maintains 0.097 Ah g^?1. The reaction mechanism of the as‐prepared CoSe₂ is also investigated. The results demonstrate that at discharged 1.56 V, insertion reaction occurs, while two conversion reactions take place at the second and third plateaus around 0.98 and 0.65 V. During the charge process, Co first reacts with Na₂Se to form Na_xCoSe₂ and then turns back to CoSe₂. In addition to Na/CoSe₂ half cells, Na₃V₂(PO₄)₃/CoSe₂ full cell with excessive amount of Na₃V₂(PO₄)₃ has been studied. The full cell exhibits a reversible capacity of 0.380 Ah g^?1. This work definitely enriches the possibilities for anode materials for SIBs with high performance.     

A Composite of Carbon‐Wrapped Mo2C Nanoparticle and Carbon Nanotube Formed Directly on Ni Foam as a High‐Performance Binder‐Free Cathode for Li‐O2 Batteries

Cathode design is indispensable for building Li‐O₂ batteries with long cycle life. A composite of carbon‐wrapped Mo₂C nanoparticles and carbon nanotubes is prepared on Ni foam by direct hydrolysis and carbonization of a gel composed of ammonium heptamolybdate tetrahydrate and hydroquinone resin. The Mo₂C nanoparticles with well‐controlled particle size act as a highly active oxygen reduction reactions/oxygen evolution reactions (ORR/OER) catalyst. The carbon coating can prevent the aggregation of the Mo₂C nanoparticles. The even distribution of Mo₂C nanoparticles results in the homogenous formation of discharge products. The skeleton of porous carbon with carbon nanotubes protrudes from the composite, resulting in extra voids when applied as a cathode for Li‐O₂ batteries. The batteries deliver a high discharge capacity of ≈10 400 mAh g^?1 and a low average charge voltage of ≈4.0 V at 200 mA g^?1. With a cutoff capacity of 1000 mAh g^?1, the Li‐O₂ batteries exhibit excellent charge–discharge cycling stability for over 300 cycles. The average potential polarization of discharge/charge gaps is only ≈0.9 V, demonstrating the high ORR and OER activities of these Mo₂C nanoparticles. The excellent cycling stability and low potential polarization provide new insights into the design of highly reversible and efficient cathode materials for Li‐O₂ batteries.     

Novel Insoluble Organic Cathodes for Advanced Organic K‐Ion Batteries

Organic redox‐active molecules are inborn electrodes to store large‐radius potassium (K) ion. High‐performance organic cathodes are important for practical usage of organic potassium‐ion batteries (OPIBs). However, small‐molecule organic cathodes face serious dissolution problems against liquid electrolytes. A novel insoluble small‐molecule organic cathode [N,N′‐bis(2‐anthraquinone)]‐perylene‐3,4,9,10‐tetracarboxydiimide (PTCDI‐DAQ, 200 mAh g^?1) is initially designed for OPIBs. In half cells (1–3.8 V vs K⁺/K) using 1 m KPF₆ in dimethoxyethane (DME), PTCDI‐DAQ delivers a highly stable specific capacity of 216 mAh g^?1 and still holds the value of 133 mAh g^?1 at an ultrahigh current density of 20 A g^?1 (100 C). Using reduced potassium terephthalate (K₄TP) as the organic anode, the resulting K₄TP||PTCDI‐DAQ OPIBs with the electrolyte 1 m KPF₆ in DME realize a high energy density of maximum 295 Wh kg^?1_cathode (213 mAh g^?1_cathode × 1.38 V) and power density of 13 800 W Kg^?1_cathode (94 mAh g^?1 × 1.38 V @ 10 A g^?1) during the working voltage of 0.2–3.2 V. Meanwhile, K₄TP||PTCDI‐DAQ OPIBs fulfill the superlong lifespan with a stable discharge capacity of 62 mAh g^?1_cathode after 10 000 cycles and 40 mAh g^?1_cathode after 30 000 cycles (3 A g^?1). The integrated performance of PTCDI‐DAQ can currently defeat any cathode reported in K‐ion half/full cells.     

Bamboo‐Like Hollow Tubes with MoS2/N‐Doped‐C Interfaces Boost Potassium‐Ion Storage

Potassium‐ion batteries (KIBs) are new‐concept of low‐cost secondary batteries, but the sluggish kinetics and huge volume expansion during cycling, both rooted in the size of large K ions, lead to poor electrochemical behavior. Here, a bamboo‐like MoS₂/N‐doped‐C hollow tubes are presented with an expanded interlayer distance of 10 Å as a high‐capacity and stable anode material for KIBs. The bamboo‐like structure provides gaps along axial direction in addition to inner cylinder hollow space to mitigate the strains in both radial and vertical directions that ultimately leads to a high structural integrity for stable long‐term cycling. Apart from being a constituent of the interstratified structure the N‐doped‐C layers weave a cage to hold the potassiation products (polysulfide and the Mo nanoparticles) together, thereby effectively hindering the continuing growth of solid electrolyte interphase in the interior of particles. The density functional theory calculations prove that the MoS₂/N‐doped‐C atomic interface can provide an additional attraction toward potassium ion. As a result, it delivers a high capacity at a low current density (330 mAh g^?1 at 50 mA g^?1 after 50 cycles) and a high‐capacity retention at a high current density (151 mAh g^?1 at 500 mA g^?1 after 1000 cycles).     

High Tap Density Co and Ni Containing P2‐Na0.66MnO2 Buckyballs: A Promising High Voltage Cathode for Stable Sodium‐Ion Batteries

Constructing high voltage (>4.5 V) cathode materials for sodium‐ion batteries has emerged in recent years to replace lithium batteries for large scale energy storage applications. Herein, an electrochemically stable Na_0.66(Ni_0.13Mn_0.54Co_0.13)O₂ (Na‐NMC) buckyballs with an uniform size of 5 µm and a high tap density of 2.34 g cm^?3, which exhibit excellent cyclability even at the high current with a cut‐off voltage of 4.7 V, is demonstrated. The Na‐NMC buckyballs are prepared from (Ni_0.13Mn_0.54Co_0.13)CO₃ (NMC) precursor synthesized using a facile hydrothermal method. The Na‐NMC delivers a reversible capacity of around 120 mAh g^?1 between 4.7 and 2 V at 1 C rate along with an excellent cyclic stability (90%) until 150 cycles, which is one of the best outcomes among the reported P2‐type cathodes tested at the high operating voltage range. Furthermore, Na‐NMC‐180 buckyballs with a high tap density is offering an enhanced volumetric energy density, a superior rate performance and an outstanding cyclic stability. The X‐ray adsorption fine structure analysis is used to study the local electronic structure changes around the Co, Mn, and Ni after cycling process at 1 C rate. The findings open opportunities for tailoring high‐performance and high‐energy cathode materials for sodium‐ion batteries.     

Few‐Layer MoSe2 Nanosheets with Expanded (002) Planes Confined in Hollow Carbon Nanospheres for Ultrahigh‐Performance Na‐Ion Batteries

Sodium‐ion batteries (SIBs) are considered as a promising alternative to lithium‐ion batteries, due to the abundant reserves and low price of Na sources. To date, the development of anode materials for SIBs is still confronted with many serious problems. In this work, encapsulation‐type structured MoSe₂@hollow carbon nanosphere (HCNS) materials assembled with expanded (002) planes few‐layer MoSe₂ nanosheets confined in HCNS are successfully synthesized through a facile strategy. Notably, the interlayer spacing of the (002) planes is expanded to 1.02 nm, which is larger than the intrinsic value of pristine MoSe₂ (0.64 nm). Furthermore, the few‐layer nanosheets are space‐confined in the inner cavity of the HCNS, forming hybrid MoSe₂@HCNS structures. When evaluated as anode materials for SIBs, it shows excellent rate capabilities, ultralong cycling life with exceptional Coulombic efficiency even at high current density, maintaining 501 and 471 mA h g^?1 over 1000 cycles at 1 and 3 A g^?1, respectively. Even when cycled at current densities as high as 10 A g^?1, a capacity retention of 382 mA h g^?1 can be achieved. The expanded (002) planes, 2D few‐layer nanosheets, and unique carbon shell structure are responsible for the ultralong cycling and high rate performance.     

Graphene Oxide Gel‐Derived,Free‐Standing,Hierarchically Porous Carbon for High‐Capacity and High‐Rate Rechargeable Li‐O2 Batteries

Lithium‐oxygen (Li‐O₂) batteries are one of the most promising candidates for high‐energy‐density storage systems. However, the low utilization of porous carbon and the inefficient transport of reactants in the cathode limit terribly the practical capacity and, in particular, the rate capability of state‐of‐the‐art Li‐O₂ batteries. Here, free‐standing, hierarchically porous carbon (FHPC) derived from graphene oxide (GO) gel in nickel foam without any additional binder is synthesized by a facile and effective in situ sol‐gel method, wherein the GO not only acts as a special carbon source, but also provides the framework of a 3D gel; more importantly, the proper acidity via its intrinsic COOH groups guarantees the formation of the whole structure. Interestingly, when employed as a cathode for Li‐O₂ batteries, the capacity reaches 11 060 mA h g^?1 at a current density of 0.2 mA cm^?2 (280 mA g^?1); and, unexpectedly, a high capacity of 2020 mA h g^?1 can be obtained even the current density increases ten times, up to 2 mA cm^?2 (2.8 A g^?1), which is the best rate performance for Li‐O₂ batteries reported to date. This excellent performance is attributed to the synergistic effect of the loose packing of the carbon, the hierarchical porous structure, and the high electronic conductivity of the Ni foam.     

Few‐Layered SnS2 on Few‐Layered Reduced Graphene Oxide as Na‐Ion Battery Anode with Ultralong Cycle Life and Superior Rate Capability

Na‐ion Batteries have been considered as promising alternatives to Li‐ion batteries due to the natural abundance of sodium resources. Searching for high‐performance anode materials currently becomes a hot topic and also a great challenge for developing Na‐ion batteries. In this work, a novel hybrid anode is synthesized consisting of ultrafine, few‐layered SnS₂ anchored on few‐layered reduced graphene oxide (rGO) by a facile solvothermal route. The SnS₂/rGO hybrid exhibits a high capacity, ultralong cycle life, and superior rate capability. The hybrid can deliver a high charge capacity of 649 mAh g^?1 at 100 mA g^?1. At 800 mA g^?1 (1.8 C), it can yield an initial charge capacity of 469 mAh g^?1, which can be maintained at 89% and 61%, respectively, after 400 and 1000 cycles. The hybrid can also sustain a current density up to 12.8 A g^?1 (≈28 C) where the charge process can be completed in only 1.3 min while still delivering a charge capacity of 337 mAh g^?1. The fast and stable Na‐storage ability of SnS₂/rGO makes it a promising anode for Na‐ion batteries.     

Cobalt‐Doped SnS2 with Dual Active Centers of Synergistic Absorption‐Catalysis Effect for High‐S Loading Li‐S Batteries

The application of Li‐S batteries is hindered by low sulfur utilization and rapid capacity decay originating from slow electrochemical kinetics of polysulfide transformation to Li₂S at the second discharge plateau around 2.1 V and harsh shuttling effects for high‐S‐loading cathodes. Herein, a cobalt‐doped SnS₂ anchored on N‐doped carbon nanotube (NCNT@Co‐SnS₂) substrate is rationally designed as both a polysulfide shield to mitigate the shuttling effects and an electrocatalyst to improve the interconversion kinetics from polysulfides to Li₂S. As a result, high‐S‐loading cathodes are demonstrated to achieve good cycling stability with high sulfur utilization. It is shown that Co‐doping plays an important role in realizing high initial capacity and good capacity retention for Li‐S batteries. The S/NCNT@Co‐SnS₂ cell (3 mg cm^?2 sulfur loading) delivers a high initial specific capacity of 1337.1 mA h g^?1 (excluding the Co‐SnS₂ capacity contribution) and 1004.3 mA h g^?1 after 100 cycles at a current density of 1.3 mA cm^?2, while the counterpart cell (S/NCNT@SnS₂) only shows an initial capacity of 1074.7 and 843 mA h g^?1 at the 100th cycle. The synergy effect of polysulfide confinement and catalyzed polysulfide conversion provides an effective strategy in improving the electrochemical performance for high‐sulfur‐loading Li‐S batteries.     

MoSe2‐Covered N,P‐Doped Carbon Nanosheets as a Long‐Life and High‐Rate Anode Material for Sodium‐Ion Batteries

MoSe₂ grown on N,P‐co‐doped carbon nanosheets is synthesized by a solvothermal reaction followed with a high‐temperature calcination. This composite has an interlayer spacing of MoSe₂ expanded to facilitate sodium‐ion diffusion, MoSe₂ immobilized on carbon nanosheets to improve charge‐transfer kinetics, and N and P incorporated into carbon to enhance its interaction with active species upon cycling. These features greatly improve the electrochemical performance of this composite, as compared to all the controls. It presents a specific capacity of 378 mAh g^?1 after 1000 cycles at 0.5 A g^?1, corresponding to 87% of the capacity at the second cycle. Ex situ Raman spectra and high‐resolution transmission electron microscopy images confirm that it is element Se, rather than MoSe₂, formed after the charging process. The interaction of the active species with modified carbon is simulated using density functional theory to explain this excellent stability. The superior rate capability, where the capacity at 15 A g^?1 equals ≈55% of that at 0.5 A g^?1, could be associated with the significant contribution of pseudocapacitance. By pairing with homemade Na₃V₂(PO₄)₃/C, this composite also exhibits excellent performances in full cells.     

A Flexible Dual‐Ion Battery Based on Sodium‐Ion Quasi‐Solid‐State Electrolyte with Long Cycling Life

Sodium‐based dual‐ion batteries (SDIBs) have attracted much attention for their advantages of high operating voltage, environmental friendliness, and especially low cost. However, the electrochemical performances of the reported SDIBs are still unsatisfied due to the decomposition problem of traditional liquid electrolyte under high working voltage. Development of quasi‐solid‐state electrolytes (QSSEs) with excellent electrochemical stability at high voltage is a possible means to improve their properties. In this work, a flexible SDIB based on a QSSE, consisting of poly(vinylidene ?uoride‐co‐hexa?uoropropylene) (PVDF‐HFP) three‐dimensionally cross‐linked with Al₂O₃ nanoparticles, which exhibits a porous 3D structure with dramatically enhanced ionic conductivity up to ≈1.3 × 10^?3 S cm^?1, facilitating fast ionic migration of both anions and cations, is reported. This quasi‐state SDIB exhibits a high specific capacity of 96.8 mAh g^?1 at a current rate of 5 C and excellent cycling stability with a capacity retention of 97.5% after 600 cycles at 5 C, which is the best performance of the SDIBs. Moreover, excellent flexibility and a wide working temperature range (?20 to 70 °C) have been realized for this battery, suggesting its potential for high‐performance flexible energy storage applications.     

Layered P2‐Type K0.65Fe0.5Mn0.5O2 Microspheres as Superior Cathode for High‐Energy Potassium‐Ion Batteries

Potassium‐ion batteries have been regarded as the potential alternatives to lithium‐ion batteries (LIBs) due to the low cost, earth abundance, and low potential of K (?2.936 vs standard hydrogen electrode (SHE)). However, the lack of low‐cost cathodes with high energy density and long cycle life always limits its application. In this work, high‐energy layered P2‐type hierarchical K_0.65Fe_0.5Mn_0.5O₂ (P2‐KFMO) microspheres, assembled by the primary nanoparticles, are fabricated via a modified solvent‐thermal method. Benefiting from the unique microspheres with primary nanoparticles, the K⁺ intercalation/deintercalation kinetics of P2‐KFMO is greatly enhanced with a stabilized cathodic electrolyte interphase on the cathode. The P2‐KFMO microsphere presents a highly reversible potassium storage capacity of 151 mAh g^?1 at 20 mA g^?1, fast rate capability of 103 mAh g^?1 at 100 mA g^?1, and long cycling stability with 78% capacity retention after 350 cycles. A full cell with P2‐KFMO microspheres as cathode and hard carbon as anode is constructed, which exhibits long‐term cycling stability (>80% of retention after 100 cycles). The present high‐performance P2‐KFMO microsphere cathode synthesized using earth‐abundant elements provides a new cost‐effective alternative to LIBs for large‐scale energy storage.     

A Low‐Cost,Self‐Standing NiCo2O4@CNT/CNT Multilayer Electrode for Flexible Asymmetric Solid‐State Supercapacitors

The demand for a new generation of flexible, portable, and high‐capacity power sources increases rapidly with the development of advanced wearable electronic devices. Here we report a simple process for large‐scale fabrication of self‐standing composite film electrodes composed of NiCo₂O₄@carbon nanotube (CNT) for supercapacitors. Among all composite electrodes prepared, the one fired in air displays the best electrochemical behavior, achieving a specific capacitance of 1,590 F g^?1 at 0.5 A g^?1 while maintaining excellent stability. The NiCo₂O₄@CNT/CNT film electrodes are fabricated via stacking NiCo₂O₄@CNT and CNT alternately through vacuum filtration. Lightweight, flexible, and self‐standing film electrodes (≈24.3 µm thick) exhibit high volumetric capacitance of 873 F cm^?3 (with an areal mass of 2.5 mg cm^?2) at 0.5 A g^?1. An all‐solid‐state asymmetric supercapacitor consists of a composite film electrode and a treated carbon cloth electrode has not only high energy density (≈27.6 Wh kg^?1) at 0.55 kW kg^?1 (including the weight of the two electrodes) but also excellent cycling stability (retaining ≈95% of the initial capacitance after 5000 cycles), demonstrating the potential for practical application in wearable devices.     

Three‐Dimensional Co3O4@MnO2 Hierarchical Nanoneedle Arrays: Morphology Control and Electrochemical Energy Storage

In this paper, a highly ordered three‐dimensional Co₃O₄@MnO₂ hierarchical porous nanoneedle array on nickel foam is fabricated by a facile, stepwise hydrothermal approach. The morphologies evolution of Co₃O₄ and Co₃O₄@MnO₂ nanostructures upon reaction times and growth temperature are investigated in detail. Moreover, the as‐prepared Co₃O₄@MnO₂ hierarchical structures are investigated as anodes for both supercapacitors and Li‐ion batteries. When used for supercapacitors, excellent electrochemical performances such as high specific capacitances of 932.8 F g^?1 at a scan rate of 10 mV s^?1 and 1693.2 F g^?1 at a current density of 1 A g^?1 as well as long‐term cycling stability and high energy density (66.2 W h kg^?1 at a power density of 0.25 kW kg^?1), which are better than that of the individual component of Co₃O₄ nanoneedles and MnO₂ nanosheets, are obtained. The Co₃O₄@MnO₂ NAs are also tested as anode material for LIBs for the first time, which presents an improved performance with high reversible capacity of 1060 mA h g^?1 at a rate of 120 mA g^?1, good cycling stability, and rate capability.     

Nanostructured Li2MnSiO4/C Cathodes with Hierarchical Macro‐/Mesoporosity for Lithium‐Ion Batteries

Li₂MnSiO₄/C nanocomposite with hierarchical macroporosity is prepared with poly(methyl methacrylate) (PMMA) colloidal crystals as a sacrificial hard‐template and water‐soluble phenol‐formaldehyde (PF) resin as the carbon source. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses confirm that the periodic macropores are ≈400 nm in diameter with 20–40 nm walls comprising Li₂MnSiO₄/C nanocrystals that produce additional large mesopores (< 30 nm) between the nanocrystals. The nanostructured Li₂MnSiO₄/C cathode exhibits a high reversible discharge capacity of 200 mAh g^?1 at C/10 (16 mA g^?1) rate at 1.5–4.8 V at 45 °C. Although the discharge capacity can be further increased on operating at 55 °C, the sample exhibits a relatively fast capacity fade at 55 °C, which can be partially solved by simply narrowing the voltage window to avoid side reactions of the electrolyte. The good performance of the Li₂MnSiO₄/C cathodes is attributed to the unique macro‐/mesostructure of the silicate coupled with uniform carbon coating.     

Self‐Standing Porous LiCoO2 Nanosheet Arrays as 3D Cathodes for Flexible Li‐Ion Batteries

Self‐standing electrodes are the key to realize flexible Li‐ion batteries. However, fabrication of self‐standing cathodes is still a major challenge. In this work, porous LiCoO₂ nanosheet arrays are grown on Au‐coated stainless steel (Au/SS) substrates via a facile “hydrothermal lithiation” method using Co₃O₄ nanosheet arrays as the template followed by quick annealing in air. The binder‐free and self‐standing LiCoO₂ nanosheet arrays represent the 3D cathode and exhibit superior rate capability and cycling stability. In specific, the LiCoO₂ nanosheet array electrode can deliver a high reversible capacity of 104.6 mA h g^?1 at 10 C rate and achieve a capacity retention of 81.8% at 0.1 C rate after 1000 cycles. By coupling with Li₄Ti₅O₁₂ nanosheet arrays as anode, an all‐nanosheet array based LiCoO₂//Li₄Ti₅O₁₂ flexible Li‐ion battery is constructed. Benefiting from the 3D nanoarchitectures for both cathode and anode, the flexible LiCoO₂//Li₄Ti₅O₁₂ battery can deliver large specific reversible capacities of 130.7 mA h g^?1 at 0.1 C rate and 85.3 mA h g^?1 at 10 C rate (based on the weight of cathode material). The full cell device also exhibits good cycling stability with 80.5% capacity retention after 1000 cycles at 0.1 C rate, making it promising for the application in flexible Li‐ion batteries.     

Hierarchical Porous Te@ZnCo2O4 Nanofibers Derived from Te@Metal‐Organic Frameworks for Superior Lithium Storage Capability

1D hierarchical porous nanocomposites with tailored chemical composition are gaining popularity in lithium‐ion batteries. Here, with core@shell Te@ZIF‐8 (Zn, Co) nanofibers as a starting point, rational designed porous Te@ZnCo₂O₄ nanocomposite has been fabricated by a simple morphology‐maintained and calcination‐induced oxidative decomposition process, with the purpose of simultaneously settling the pulverization and conductivity issues of transition metal oxides. This is the first time to integrate Te and ZnCo₂O₄ into one architecture at nanometer level. The Te@ZnCo₂O₄ nanofibers combine both advantages of Te such as excellent electrical conductivity and ZnCo₂O₄ with high capacity as well as take full use of their synergistic effect. With the favorable 1D porous structure and the unique composition, this novel Te@ZnCo₂O₄ nanofiber manifests strong ability to improve the lithium storage performances with a high specific capacity of 1364 mA h g^?1 in the initial discharge and a reversible capacity of 956 mA h g^?1 after 100 cycles. When increased the current density to 2000 mA g^?1, the capacity still remains as 307 mA h g^?1, demonstrating superior rate capability. Furthermore, this general strategy can be extended to construct other core@shell Te@MOFs composites.     

ZnCl2 “Water‐in‐Salt” Electrolyte Transforms the Performance of Vanadium Oxide as a Zn Battery Cathode

Zn batteries potentially offer the highest energy density among aqueous batteries that are inherently safe, inexpensive, and sustainable. However, most cathode materials in Zn batteries suffer from capacity fading, particularly at a low current rate. Herein, it is shown that the ZnCl₂ “water‐in‐salt” electrolyte (WiSE) addresses this capacity fading problem to a large extent by facilitating unprecedented performance of a Zn battery cathode of Ca_0.20V₂O₅?0.80H₂O. Upon increasing the concentration of aqueous ZnCl₂ electrolytes from 1 m to 30 m, the capacity of Ca_0.20V₂O₅?0.80H₂O rises from 296 mAh g^?1 to 496 mAh g^?1; its absolute working potential increases by 0.4 V, and most importantly, at a low current rate of 50 mA g^?1, that is, C/10; its capacity retention increases from 8.4% to 51.1% over 100 cycles. Ex situ characterization results point to the formation of a new ready‐to‐dissolve phase on the electrode in the dilute electrolyte. The results demonstrate that the Zn‐based WiSE may provide the underpinning platform for the applications of Zn batteries for stationary grid‐level storage.     

Enhanced Performance of P2‐Na0.66(Mn0.54Co0.13Ni0.13)O2 Cathode for Sodium‐Ion Batteries by Ultrathin Metal Oxide Coatings via Atomic Layer Deposition

Sodium‐ion batteries are widely considered as promising energy storage systems for large‐scale applications, but their relatively low energy density hinders further practical applications. Developing high‐voltage cathode materials is an effective approach to increase the overall energy density of sodium‐ion batteries. When cut‐off voltage is elevated over 4.3 V, however, the cathode becomes extremely unstable due to structural transformations as well as metal dissolution into the electrolytes. In this work, the cyclic stability of P2‐Na_0.66(Mn_0.54Co_0.13Ni_0.13)O₂ (MCN) electrode at a cut‐off voltage of 4.5 V is successfully improved by using ultrathin metal oxide surface coatings (Al₂O₃, ZrO₂, and TiO₂) deposited by an atomic layer deposition technique. The MCN electrode coated with the Al₂O₃ layer exhibits higher capacity retention among the MCN electrodes. Moreover, the rate performance of the MCN electrode is greatly improved by the metal oxide coatings in the order of TiO₂ < Al₂O₃ < ZrO₂, due to increased fracture toughness and electrical conductivity of the metal oxide coating layers. A ZrO₂‐coated MCN electrode shows a discharge capacity of 83 mAh g^?1 at 2.4 A g^?1, in comparison to 61 mAh g^?1 for a pristine MCN electrode. Cyclic voltammetry and electrochemical impedance analysis disclose the reduced charge transfer resistance from 1421 to 760.2 Ω after cycles, suggesting that the metal oxide coating layer can effectively minimize the undesirable phase transition, buffer inherent stress and strain between the binder, cathode, and current collector, and avoid volumetric changes, thus increasing the cyclic stability of the MCN electrode.     

Self‐Assembly of Flexible Free‐Standing 3D Porous MoS2‐Reduced Graphene Oxide Structure for High‐Performance Lithium‐Ion Batteries

Flexible freestanding electrodes are highly desired to realize wearable/flexible batteries as required for the design and production of flexible electronic devices. Here, the excellent electrochemical performance and inherent flexibility of atomically thin 2D MoS₂ along with the self‐assembly properties of liquid crystalline graphene oxide (LCGO) dispersion are exploited to fabricate a porous anode for high‐performance lithium ion batteries. Flexible, free‐standing MoS₂–reduced graphene oxide (MG) film with a 3D porous structure is fabricated via a facile spontaneous self‐assembly process and subsequent freeze‐drying. This is the first report of a one‐pot self‐assembly, gelation, and subsequent reduction of MoS₂/LCGO composite to form a flexible, high performance electrode for charge storage. The gelation process occurs directly in the mixed dispersion of MoS₂ and LCGO nanosheets at a low temperature (70 °C) and normal atmosphere (1 atm). The MG film with 75 wt% of MoS₂ exhibits a high reversible capacity of 800 mAh g^?1 at a current density of 100 mA g^?1. It also demonstrates excellent rate capability, and excellent cycling stability with no capacity drop over 500 charge/discharge cycles at a current density of 400 mA g^?1.