纤维用PET/CGP的共混改性研究

采用聚对苯二甲酸乙二醇酯(PET)与聚对苯二甲酸乙二醇酯聚对苯二甲酸丁二醇酯聚丁二醇共聚酯(CGP)以不同比例共混制得一系列的改性聚酯,研究了共混改性聚酯切片的热性能和流变性能。结果表明,随着CGP加入量的增加,PET/CGP共混体系的玻璃化转变温度Tg,冷结晶峰温度Tc和熔点Tm均有所下降,热稳定性比普通PET低;PET/CGP熔体呈现“切力变稀”现象,其表观黏度明显下降。     

聚(对苯二甲酸乙二醇酯-co-对苯二甲酸异山梨醇酯)预结晶及固相聚合研究

研究了不同异山梨醇(ISB)含量的聚(对苯二甲酸乙二醇酯-co-对苯二甲酸异山梨醇酯)(PEIT)共聚酯预结晶及固相聚合工艺。探讨了温度、时间与PEIT共聚酯预结晶温度、固相聚合反应速率之间的关系;利用差式扫描量热仪(DSC)分析研究PEIT共聚固相聚合前后的热性能变化情况。结果表明:随着ISB用量的增加,PEIT共聚酯结晶困难,预结晶时间增加,固相聚合反应速率减慢;随着温度升高,PEIT共聚酯固相聚合反应速率加快,但仍慢于聚对苯二甲酸乙二醇酯(PET);固相增粘后PEIT共聚酯玻璃化转变温度(Tg)与ISB含量呈线性上升关系。     

PET/硅灰石纤维复合材料的结晶动力学研究

聚对苯二甲酸乙二醇酯(PET)性能十分优异,使用范围十分广泛,但是由于结晶速度过慢,需要对其进行改性。本实验先将硅灰石纤维制成母料,再用母粒对聚对苯二甲酸己二醇酯(PET)进行改性,对硅灰石纤维改性PET复合材料进行了差示扫描式量热(DSC)测试,并使用莫氏理论对其非等温降温结晶过程进行了动力学分析。     

聚(对苯二甲酸乙二醇酯-co-对苯二甲酸异山梨醇酯)等温结晶行为研究

以对苯二甲酸(PTA)、乙二醇(EG)、异山梨醇(ISB)为原料,通过直接熔融缩聚法合成聚(对苯二甲酸乙二醇酯-co-对苯二甲酸异山梨醇酯)(PEIT)共聚酯。利用差示扫描量热法(DSC)研究了共聚酯的结晶行为,采用Avrami方程分析了共聚酯的等温结晶动力学。结果表明,PEIT共聚酯结晶行为受共聚组成和结晶温度影响。随着ISB用量的增加或结晶温度的降低,共聚酯半结晶周期t1/2增加、结晶速率变慢;ISB摩尔分数超过20%,共聚酯无法结晶。     

生物可降解塑料的生产现状及应用

综述了生物可降解塑料聚乳酸、聚(己二酸丁二酯-co-对苯二甲酸丁二酯)、聚乙醇酸、聚羟基脂肪酸酯、聚丁二酸丁二酯、聚己内酯用途以及现有产能和在建情况。介绍了生物可降解塑料对于传统塑料的替代,到2025年,快递行业需要1 000 kt生物可降解塑料,外卖餐饮行业生物可降解塑料替代空间达到700 kt。     

聚酯瓶包装

综述了PET(聚对苯二甲酸乙二醇酯)和PEN(聚萘二甲酸乙二醇酯)瓶的特点、市场、应用结构、需求预测和发展动向,并讨论了聚酯瓶的回收问题。     

聚对苯二甲酸乙二醇酯／蒙脱土复合物的制备与表征

分别采用蒙脱土与对苯二甲酸乙二醇酯(BHET)和与乙二醇(EG)混合的方法，通过原位插层聚合制备聚对苯二甲酸乙二醇酯／蒙脱土(PET／MMT)复合材料，研究了MMT含量对PET粘均相对分子质量、复合材料微观结构及热和结晶性能的影响。结果表明，随有机化MMT的加入量增加，PET的粘均相对分子质量降低；将有机化MMT分散在乙二醇中再聚合所得复合物中MMT分散更为均匀；MMT的加入使PET的玻璃化温度、冷结晶温度和维卡软化温度降低，BHET法的PET结晶度和热结晶温度增加，而EG法的PET结晶度和热结晶温度下降。     

利用废弃PET酯交换法合成PBAT的研究

以废弃聚对苯二甲酸乙二醇酯（PET）矿泉水瓶为原料,采用酯交换法获得聚对苯二甲酸丁二醇酯（PBT）预聚体,再与聚己二酸丁二醇酯（PBA）共聚获得聚对苯二甲酸/己二酸丁二醇酯（PBAT）产物,通过核磁共振光谱仪、红外光谱仪、热重分析仪、差示扫描量热分析仪和万能试验机等对PBAT产物的结构和性能进行了分析表征。结果表明,PBAT产物的热稳定性良好,300℃以内不会热分解;PBAT产物的水接触角是78.54°,是一种亲水材料;PBAT产物的断裂伸长率达到900%以上,具备进一步应用推广的可能性。     

过渡金属Mn取代多金属氧簇催化醇解废旧PET

合成了一种具有三明治结构的过渡金属Mn取代的多金属氧簇(POMs)催化剂Na12[WZnMn2(H2O)2(ZnW9O34)2],用于催化聚对苯二甲酸乙二醇酯(PET)的醇解过程,对反应温度、反应时间和催化剂量等实验条件进行了优化。结果表明,在催化剂量为PET质量的1.0%、质量比PET/EG(乙二醇)为1:4及190℃的条件下反应80 min,PET降解率可达100%,对苯二甲酸乙二醇酯(BHET)的收率达84.42%。     

PET／蒙脱土纳米复合材料的制备及其性能研究

将十六烷基三甲基溴化铵／聚乙二醇混合物处理的蒙脱土与聚对苯二甲酸乙二醇酯在哈克流变仪上进行熔融复合，制备了聚对苯二甲酸乙二醇酯(PET)/蒙脱土纳米复合材料。X射线衍射以及透射电镜分析表明，蒙脱土层间距明显增大，部分剥离并分散于PET基体中。对其力学性能和热性能的分析发现，当有机化蒙脱土用量为5％(质量含量，下同)时，材料的热变形温度及弯曲模量分别达到154℃和3．335GPa。     

Melting,crystallization behaviors,and nonisothermal crystallization kinetics of PET/PTT/PBT ternary blends

The melting, crystallization behaviors, and nonisothermal crystallization kinetics of the ternary blends composed of poly(ethylene terephthalate), poly(trimethylene terephthalate) (PTT) and poly(buthylene terephthalate) (PBT) were studied with differential scanning calorimeter (DSC). PBT content in all ternary blends was settled invariably to be one‐third, which improved the melt‐crystallization temperature of the ternary blends. All of the blend compositions in amorphous state were miscible as evidenced by a single, composition‐dependent glass transition temperature (T_g) observed in DSC curves. DSC melting thermograms of different blends showed different multiple melting and crystallization peaks because of their various polymer contents. During melt‐crystallization process, three components in blends crystallized simultaneously to form mixed crystals or separated crystals depending upon their content ratio. The Avrami equation modified by Jeziorny and the Ozawa theory were employed to describe the nonisothermal crystallization process of two selected ternary blends. The results spoke that the Avrami equation was successful in describing the nonisothermal crystallization process of the ternary blends. The values of the t_1/2 and the parameters Z_c showed that the crystallization rate of the ternary blends with more poly(ethylene terephthalate) content was faster than that with the lesser one at a given cooling rate. The crystal morphology of the five ternary blends investigated by polarized optical microscopy (POM) showed different size and distortional Maltese crosses or light spots when the PTT or poly(ethylene terephthalate) component varied, suggesting that the more the PTT content, the larger crystallites formed in ternary blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Synthesis and characterisation of copolyesters from poly(ethylene terephthalate) and poly(hexamethylene terephthalate)

Copolyesters containing poly(ethylene terephthalate) and poly(hexamethylene terephthalate) (PHT) were prepared by a melt condensation reaction. The copolymers were characterised by infrared spectroscopy and intrinsic viscosity measurements. The density of the copolyesters decreased with increasing percentage of PHT segments in the backbone. Glass transition temperatures (T_g). melting points (T_m) and crystallisation temperatures (T_c) were determined by differential scanning calorimetry. An increase in the percentage of PHT resulted in decrease in T_g, T_m and T_c. The as-prepared copolyesters were crystalline in nature and no exotherm indicative of cold crystallisation was observed. The relative thermal stability of the polymers was evaluated by dynamic thermogravimetry in a nitrogen atmosphere. An increase in percentage of PHT resulted in a decrease in initial decomposition temperature. The rate of crystallisation of the copolymers was studied by small angle light scattering. An increase in percentage of PHT resulted in an increase in the rate of crystallisation.     

Blends of poly(ethylene terephthalate) and poly(butylene terephthalate)

Commercial grade poly(ethylene terephthalate), (PET, intrinsic viscosity = 0.80 dL/g) and poly(butylene terephthalate), (PBT, intrinsic viscosity = 1.00 dL/g) were melt blended over the entire composition range using a counterrotating twin‐screw extruder. The mechanical, thermal, electrical, and rheological properties of the blends were studied. All of the blends showed higher impact properties than that of PET or PBT. The 50:50 blend composition exhibited the highest impact value. Other mechanical properties also showed similar trends for blends of this composition. The addition of PBT increased the processability of PET. Differential scanning calorimetry data showed the presence of both phases. For all blends, only a single glass‐transition temperature was observed. The melting characteristics of one phase were influenced by the presence of the other. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 75–82, 2005     

聚对苯二甲酸甲二酯的热分解行为及其动力学研究

研究了惰性气氛下聚对苯二甲酸甲二酯(PMT)的非等温热分解行为及其动力学,并与聚对苯二甲酸丁二酯 (PBT)进行了对比。研究发现,PMT的热降解过程包括两个主要失重阶段,其热分解反应不是一级反应。第一阶段的起始分解温度较低是由于产物的分子链末端基中含有Br或Cl能催化聚合物的降解反应;第二阶段为分子链主体的热分解过程,由于分子链中苯环的密度较大,分子链的热稳定性比具有较低苯环密度的PBT要高。而PBT的降解失重过程仅为一个阶段,为一级反应。     

PET与PTT共聚酯的合成及其性能研究

采用直接酯化法合成了不同比例的PET与PTT共聚酯,研究了所得共聚酯的热性能、力学性能及染色性等与不同组成比之间关系。     

PET/PTT共混体系的研究进展

综述了PET/PTT共混体系的国内外发展现状,重点对共混体系的相容性,共混体系的结构形态,熔融结晶行为和结晶动力学和结晶熔融行为进行了论述,并对其发展前景进行了展望。     

Properties of glass‐filled thermoplastic polyesters

The thermal, mechanical, and rheological properties of glass‐filled poly(propylene terephthalate) (GF PPT) were compared to glass‐filled poly(butylene terephthalate) (GF PBT). The impetus for this study was the recent commercial interest in PPT as a new glass‐reinforced thermoplastic for injection‐molding applications. This article represents the first systematic comparison of the properties of GF PPT and GF PBT in which differences in properties can be attributed solely to differences in the polyester matrices, that is, glass‐fiber size and composition, polymer melt viscosity, nucleant content and composition, polymerization catalyst composition and content, and processing conditions were kept constant. Under these controlled conditions, GF PPT showed marginally higher tensile and flexural properties and significantly lower impact strength compared to GF PBT. The crystallization behavior observed by cooling from the melt at a constant rate showed that GF PBT crystallized significantly faster than did GF PPT. Nucleation of GF PPT with either talc or sodium stearate increased the rate of crystallization, but not to the level of GF PBT. The slower crystallization rate of GF PPT was found to strongly affect thermomechanical properties of injection‐molded specimens. For example, increasing the polymer molecular weight and decreasing the mold temperature significantly increased the modulus drop associated with the glass transition. In contrast, the modulus–temperature response of GF PBT was just marginally influenced by the polymer molecular weight and was essentially independent of the mold temperature. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 889–899, 1999     

PTT／PET共混体系结晶行为和形态研究

利用差示扫描量热仪、正交偏光显微镜研究了聚对苯二甲酸丙二醇酯(PTT)、聚对苯二甲酸乙二醇酯(PET)及PTT/PET共混体系(质量比为25∶75)的结晶行为、形态和等温结晶动力学。结果表明,PTT/PET共混物中,少量的PTT部分地起到了成核作用,但在一定程度上阻碍了PET链段规则地进入晶格,影响了结晶速率。偏光显微镜观察到PET、PTT和PTT/PET共混物在120℃下1、20min的溶液滴膜有较清晰的球晶。     

Polymorphic and miscibility behavior in crystalline/crystalline blends of poly(pentamethylene terephthalate) with poly(heptamethylene terephthalate)

BACKGROUND: The phase behavior of blends of semicrystalline aryl polyesters with long methylene segments (? (CH₂)_n? with n = 5 or 7) in the repeat units has not been much studied. Thus, crystalline/crystalline blends comprising monomorphic poly(pentamethylene terephthalate) (PPT) and polymorphic poly(heptamethylene terephthalate) (PHepT) were prepared and the crystal growth kinetics, polymorphism behavior and miscibility in this blend system were probed using polarized‐light optical microscopy, differential scanning calorimetry and wide‐angle X‐ray diffraction. RESULTS: The PPT/PHepT blends of all compositions were first proven to be miscible in the melt state or quenched amorphous phase, whose interaction strength was determined (χ₁₂ = ? 0.35), showing favorable interactions and phase homogeneity. Although the spherulites of neat PPT and PHepT could exhibit ring bands at different crystallization temperature (T_c) ranges (100–110 and 50–65 °C, respectively), the spherulites of PPT/PHepT (50/50) blend became ringless in the range 50–110 °C. Growth analysis and polymorphic behavior in the crystalline phases of the blends provided extra evidence for the miscibility between these two crystalline polymers. Spherulitic growth rates of PPT in the PPT/PHepT blends were significantly reduced in comparison with those of neat PPT. In addition, miscible blending of a small fraction of monomorphic PPT (20 wt%) with polymorphic PHepT altered the crystal stability and led to the originally polymorphic PHepT exhibiting only the β‐crystal form when melt‐crystallized at all values of T_c. CONCLUSION: The highly intimate mixing in polymer chains of crystalline PPT and PHepT causes significant disruption in ring‐band patterns and reduction in crystallization rates of PPT as well as alteration in the polymorphic behavior of PHepT. Copyright © 2009 Society of Chemical Industry     

PET/PTT合金结晶形态的研究

采用XP-201热台偏光显微镜研究了对苯二甲酸乙二醇酯（PET）/对苯二甲酸丙二醇酯（PTT）合金等温结晶时的结晶形态及影响因素。研究结果表明：随着等温结晶温度的升高,PET/PTT(40/60)合金的结晶诱导期变长;在观察的时间范围内各样品的球晶尺寸随着时间的延长而增大;随着PTT含量的增加,样品球晶的线生长速率增大,球晶尺寸增大;对比不同温度下等温结晶的球晶形态,PET/PTT(100/0)样品在190℃结晶时球晶尺寸最大, PET/PTT(40/60)样品和PET/PTT(100/0)样品在180℃结晶时球晶尺寸最大; PET/PTT(0/100)样品等温结晶时呈现出了复杂的条带球晶。