Fast and Secure Handover Authentication Scheme Based on Ticket for WiMAX and WiFi Heterogeneous Networks

Integrated WiMAX and WiFi networks is of great potential for the future due to the wider coverage of WiMAX and the high data transport capacity of WiFi. However, seamless and secure handover (HO) is one of the most challenging issues in the WiMAX and WiFi heterogeneous networks. In this paper, we present a fast and secure HO authentication scheme based on credential ticket for WiMAX and WiFi heterogeneous networks. In the proposed scheme, Mobile Station (MS) shows its corresponding credential ticket generated by the previously visited Base Station (BS)/Access Point (AP) to the target BS/AP whenever an HO occurs, and then the MS and target BS/AP can complete the mutual authentication and derive their shared session key without interacting with the Authentication, Authorization, and Accounting server, which significantly reduces the HO authentication delay. Moreover, our scheme fulfills the essential security requirements in HO authentication semantics and the formal verification by the AVISPA tool shows that the proposed scheme is secure against various malicious attacks. In addition, the theoretical analysis and simulation indicate that our scheme outperforms the existing HO authentication schemes in terms of communication and computation cost.     

Throughput Evaluation of Oversampled Receiver: An Example of WiMAX System

In this paper, we propose an oversampled WiMAX receiver as an attempt to improve throughput of WiMAX system. In communication, oversampling is a technique that a signal is sampled with a higher sampling frequency than its original bandwidth at the receiver side. Thus more signal sequences, which is received through different paths, may be obtained compare to system with conventional sampling. These additional sequences generate diversity. This study theoretically analyzes an oversampled wireless communication system in case of capacity with outage over Rayleigh distributed flat fading channel and presents throughput of the oversampled WiMAX receiver that obtained by simulation over a realistic channel model and by experimental tests. Since the performance of an oversampled system very much depends on the channel conditions, realistic channel model and experimental study are essential to exhibit realistic performance benchmarks. Theoretical analyzes, simulations and experimental results clearly show that the oversampled receiver significantly outperforms the spectrum efficiency of the communication system.     

Design and implementation of a new scheduler for enhancing multi-rate fairness in IEEE 802.16

Without the definition of a mandatory scheduling algorithm for channel resource assignment, WiMAX is open to Quality of Service (QoS) enhancements by research groups and developers, at the aim of managing heterogeneous flows with different QoS requirements. Furthermore, besides performance enhancement, another key issue arises for QoS delivery: it is known as multi-rate fairness and it deals with efficient resource allocation for providing sufficient bandwidth to high rate flows, without penalizing low rate ones. In this paper, uplink scheduling algorithms are studied and an innovative solution is proposed to achieve performance enhancement, multi-rate fairness and improved QoS management. After an overview of the state of the art, two scheduling algorithms based on Deficit Round Robin are studied, implemented and tested in NS2 simulator. The schedulers are validated and compared through exhaustive simulations, showing the benefits coming from the adoption of the proposed scheduling mechanism.     

UPTIME: an IMS-based mobility framework for next generation mobile networks

Seamless inter-technology mobility is one of the fundamental requirements of next generation mobile networks. For seamless mobility, handover delay and packet loss should be minimized. However, existing solutions suffer from a number of shortcomings in satisfying these requirements: first, handover preparation schemes fail to minimize the handover delay as much as possible. Second, minimizing packet loss which is usually using soft handover (SHO) schemes are excessively wasteful of scarce resources. In this paper, we propose the uninterrupted proactive connection transfer for IMS mobility enhancement (UPTIME) mobility framework which achieves seamless mobility while minimizing excessive power and radio resource consumption. UPTIME incorporates two mechanisms; a proactive handover preparation method and an optimized SHO technique for handover execution. We demonstrate the benefits of the proposed framework through both analysis and simulation. Our simulation results for typical LTE/WiMAX handovers show that the handover preparation delay can be reduced by 70 %, and good packet loss performance can be achieved whilst saving 43 % of radio resources and 48 % of battery power.     

Compact Planar Monopole Antenna with Dual Band Notched Characteristics Using T-Shaped Stub and Rectangular Mushroom Type Electromagnetic Band Gap Structure for UWB and Bluetooth Applications

In this paper, an ultra-wideband (UWB) antenna with dual band-notched characteristics is proposed. The proposed antenna also covers ISM (Industrial, Scientific, and Medical)/Bluetooth band. The antenna consists of a microstrip fed truncated U-shaped patch, T-shaped stub, rectangular mushroom type electromagnetic band gap structures (EBG), and partial ground plane. To mitigate the problem of interference due to standard narrow bands (like wireless interoperability microwave access (WiMAX) and wireless local area network (WLAN)) lie in the range of UWB, dual band notched characteristics is introduced. The WiMAX and WLAN band notched characteristics are realized by introducing a T-shaped stub and rectangular mushroom type EBG structures, respectively. The proposed antenna is printed on a 1.6 mm thick FR4 substrate with relative permittivity \((\upvarepsilon _{\mathrm{r}})\) 4.4 and the size of actual antenna is \(36 \times 40\hbox { mm}^{2}\) . The measured results shows that the proposed antenna attains a wide impedance bandwidth \((\hbox {VSWR} \le 2)\) from 2.35 to 11.6 GHz with dual band notched characteristics from 3.29 to 3.9 GHz and 5.1 to 5.85 GHz with stable radiation patterns. The time domain behaviors of the proposed antenna is also analyzed for pulse handling capability.     

Triple cascaded current-reuse low noise amplifier

A triple cascaded current-reuse CMOS low noise amplifier for 3.5 GHz WiMAX application is presented. Three common-source amplifiers are stacked and reuse the same current. This triple cascaded topology is able to enhance power gain but needs two coupling networks which costs enormous chip size. In order to have reasonable chip size, two coupling methods are investigated. For obtaining simultaneous input and noise matching, an additional capacitor is employed to adjust quality factor and reduce the gate induced current noise. The measurement results show a maximum power gain of 21.7 dB and minimum noise figure of 3.11 dB. The chip size is 1.05 mm \(\times\) 0.93 mm including all pads and the power consumption is 5.16 mW with a supply voltage of 1.5 V. A figure-of-merit of 49.7 is reached.     

Radio resource allocation algorithms for multi-service OFDMA networks: the uniform power loading scenario

Adaptive Radio Resource Allocation is essential for guaranteeing high bandwidth and power utilization as well as satisfying heterogeneous Quality-of-Service requests regarding next generation broadband multicarrier wireless access networks like LTE and Mobile WiMAX. A downlink OFDMA single-cell scenario is considered where heterogeneous Constant-Bit-Rate and Best-Effort QoS profiles coexist and the power is uniformly spread over the system bandwidth utilizing a Uniform Power Loading (UPL) scenario. We express this particular QoS provision scenario in mathematical terms, as a variation of the well-known generalized assignment problem answered in the combinatorial optimization field. Based on this concept, we propose two heuristic search algorithms for dynamically allocating subchannels to the competing QoS classes and users which are executed under polynomially-bounded cost. We also propose an Integer Linear Programming model for optimally solving and acquiring a performance upper bound for the same problem at reasonable yet high execution times. Through extensive simulation results we show that the proposed algorithms exhibit high close-to-optimal performance, thus comprising attractive candidates for implementation in modern OFDMA-based systems.     

Implementation of AES Key Schedule Using Look-Ahead Technique

The commencement of decryption process of Advanced Encryption Standard (AES) algorithm is dependent on availability of the last round key. In this paper, we propose a look-ahead technique for increasing the speed of implementation of AES key schedule using which the last round key can be made available fast. The other round keys can also be computed in a parallel path using the proposed technique. Applications such as key search engines need to be agile to key changes for decrypting given encrypted messages using all the keys in the available key space so that fast decryption is possible. The FPGA implementation results using Xilinx XC5VLX85 are also provided.     

System study on direct sequence spectrum of radio-frequency identification

This paper considers points of secure and anti-collision of the Radio-frequency identification (RFID) technology. Source symbols are represented by a special coding, termed Minimum Energy (ME) coding, which exploits redundant bits for saving power when transmitted via RF links with On-Off Keying (OOK). This ME coding is applied to Direct Sequence Spread Spectrum (DSSS) RFID tag in order to enhance security as well as to reduce collision. This synchronized DSSS RFID system is designed and simulation is conducted to verify the advantage of DSSS RFID and present the power efficiency enhance 4 dB, quantities are taken at Bit Error Rate (BER) of 10e-4. When the channel uses the ME coding combined with a DSSS code and OOK without FM0 encoding as is disclosed in the EPC-C1G2/ISO 18000-6 Type C standard. Finally, the maximum number of users in this Direct-Sequence Code Division Multiple Access (DS-CDMA) RFID system is calculated under the condition of successfully acquired.     

Specific features of the hydride vapor-phase epitaxy of nitride materials on a silicon substrate

Specific features of the growth of the GaN/AlN/Si heterocomposite in which layers of Group-III element nitrides are grown on a silicon substrate by hydride vapor-phase epitaxy are studied. The effect of the temperature at which the AlN buffer layer is grown on diffusion processes at the heterointerfaces and on the quality of the epitaxial layers being grown is considered. It is shown that, with the epitaxial technique used, the buffer layer should be grown at high temperatures (1080°C) because the thickness of the component-mixing region is minimized in this case and abrupt interfaces are formed in the GaN/AlN/Si heterocomposite. The double-stage growth of gallium nitride on the high-temperature AlN buffer layer with a thickness of 300–400 nm makes it possible to obtain GaN layers with thicknesses of up to 0.3 μm without crack formation.     

Simulation of Terahertz Generation from Lateral Diffusion Currents in Semiconductor Devices

In this paper we model the carrier dynamics and resulting THz emission from lateral diffusion currents within a semiconductor device which has been partially masked by a metallic mask. We present a numerical 1D model and a 1D Monte Carlo simulation which both demonstrate that regardless of the excitation laser spot shape we do not expect to see measurable THz emission in the direction of the optical pump propagation from lateral diffusion currents. Experimentally such devices do produce strong THz emission. We analytically investigate the role of the metal mask and we found that it suppresses the emission of dipoles that are in a region that is less than a wavelength away from the interface. The results from the numerical model are also included in a finite element analysis model of the geometry which predicts THz emission if and only if the metal mask is present.     

Channel Estimation in Long Term Evolution Uplink Using Minimum Mean Square Error-Support Vector Regression

In this paper, minimum mean square error-support vector regression (MMSE-SVR) is proposed, which is shown to be adequate for the estimation of the long term evolution (LTE) uplink channel with nonlinear features. MMSE-SVR was applied to estimate real channel environments such as the vehicular A channels defined by the International Telecommunication Union (ITU). The simulation results show that the proposed method has a better performance than the least squares support vector machine (LS-SVM) and the standard MMSE with linear and spline interpolation.     

Effects of Propagation Models on AODV in Mobile Ad-hoc Networks

Mobile ad-hoc networks (MANET) operate like self organizing entity. The mobile nodes are operate in a host as well as in a router and dynamic topology. In MANET every network node operates autonomously. It has limited resources like power, bandwidth and storage capacity. Selection of a propagation model plays the vital role of application possibilities in MANET. In this paper, calculations have been performed for three propagation models: Two-ray ground, COST 231 and Okumura–Hata model. The paper shows the impact of these propagation models based on Ad-hoc on-demand distance vector (AODV) protocol at 1.5 GHz frequency, varying transmitted power and number of nodes. This paper also studies effects of the propagation models with the conclusion of choosing the most accurate propagation model. Okumura–Hata propagation model shows better results at 1.5 GHz frequency as compared to COST 231 and Two-ray ground model in open space using Network Simulator (NS 2.35). Two-ray ground propagation model shows better results with varying transmitted power and number of nodes as compared to COST 231 and Okumura–Hata model.     

Ant Optimized Link Quality for Ad Hoc on Demand Distance Vector

The wireless interfaces in Mobile Ad-Hoc Networks (MANETs) have limited transmission range and traffic is relayed through intermediate nodes to ensure intra node communication. Routing plays an important role in network reliability and performance. MANET’s characteristics like mobility and resource constraints adversely affect routing performance. A new MANET routing method based on Ad hoc On- demand Distance Vector (AODV) and Ant Colony Optimization is proposed in this paper. Ad hoc networks can emulate achievement of complex solutions with limited intelligence and individual capacity as seen in ant communities. A new link quality metric enhances AODV routing algorithm to enable it to handle link quality to evaluate routes between nodes.     

A practical RFID authentication mechanism for digital television

As information technology continuously progresses, more applied technologies are developed, such as radio frequency identification (RFID). In this paper, we propose a novel digital television (DTV) structure that uses RFID for encryption. RFID is widely used for various applications because of its advantages such as an extended lifetime and security, and it is less affected by environmental constraints. The proposed protocol uses RFID for encryption to withstand many attacks that the traditional system is vulnerable to, such as impersonation attack, replay attack and smart card cloning. Compared with other protocols, the proposed protocol is more secure and efficient. Thus, our proposed protocol makes the DTV framework more complete and secure.     

Fir laser stabilization using stark effect: Data on CH3Br and CH3Cl

Data on the influence of the Stark Effect on an optically pumped FIR laser with CH₃Cl or CH₃Br as active medium are given for various wavelengths. A very simple method for an effective FIR power stabilisation based on the Stark Effect is described. Its working is illustrated with the EPR signal of a 10% diluted DAG sphere.     

GaAs Schottky barrier mixer diodes for the frequency range 1–10 THz

Recent technological advances have made possible the development of heterodyne receivers with high sensitivity and high spectral resolution for frequencies up to 3,000 GHz (3 THz). These receivers rely on GaAs Schottky barrier mixer diodes to translate the high-frequency signal to a lower frequency where amplification and signal processing are possible. In the frequency range from 1–10 THz several new effects will limit diode performance. These effects are discussed and guidelines for diode design are presented.     

Charge transport in Si-SiO2 and Si-TiO2 nanocomposite structures

The experimental data on dispersed Si-SiO₂ and Si-TiO₂ nanocomposite structures different in terms of physical, chemical, and insulator properties of oxide components are reported. The parameters of the nanocomposite structures are studied by FTIR spectroscopy and impedance spectroscopy. It is shown that, in such structures, the mechanisms of charge-carrier transport are defined by the properties of Si nanocrystallites and the corresponding oxide as well as by interaction processes at interfaces between grains.     

The Performance of the Adaptive Aggregation Mechanism (AAM) Under Mixed Traffic Loads

The adaptive packet aggregation algorithm (AAM) has been shown to have a superior performance over the first-in first-out (FIFO) algorithm in terms of the throughput and delay (Deng and Davis in International conference on wireless communications and signal processing 2013 (WCSP2013), Hangzhou, China, pp 449–504, 2013; 20th IEEE symposium on communications and vehicular technology in the Benelux 2013 (IEEE SCVT 2013), Namur, 2013). In this paper, we will show that when compared with the FIFO and smallest-size first-served algorithms, the AAM algorithm has the best performances in terms of the trade-off between the overhead saving and the average delay under mixed traffic loads in wireless LANs. The simulation results show that the AAM algorithm produces the largest average aggregate packet size.     

Wavelet Based Identification of Substances in Terahertz Tomography Measurements

In comparison to the X-ray computed tomography Terahertz technique significantly enhances the amount of the information acquired during the sample measurement. Not only amplitude, but also phase, time and spectral characteristics can be determined in THz time-domain spectroscopy. Thus, Terahertz tomography allows localization and identification of substances within the objects due to the characteristic fingerprints in this frequency range. Certainly, an appropriate data processing and comparison algorithms are crucial for the accurate identification of the substances in the measured sample. Therefore, we present a new wavelet-based identification method which is suitable even for the substances with broad absorption curves and small or no absorption peaks. The performance of this algorithm was evaluated with the help of a tomographic sample filled with four substances, which were previously characterized for the external database. The continuous wavelet transform was applied to every data cell of the tomographic measurement and compared to the database. Received sinograms were reconstructed into images which depict estimated similarity between the measured and database substances. Furthermore, we suggest a method for the reduction of spectral data after the continuous wavelet transform. This method is based on the extraction of the distinctive features in the form of ridge lines.