共查询到20条相似文献,搜索用时 31 毫秒
1.
In situ growth of needlelike LaAl 11O 18 grains reinforcing Al 2O 3 composites can be fabricated by a coprecipitation method using La(NO 3) 3√6H 2O and Al(NO 3) 3√9H 2O as starting materials. The new two-step process involved firstly preparing needlelike LaAl 11O 18 grains distributed homogeneously in Al 2O 3 powder and then pressureless sintering the composite powders. The Al 2O 3/25 vol.%LaAl 11O 18 samples pressureless sintered at 1550°C for 4 h achieve relative density up to 96.5% and exhibit a bending strength of 420±30 MPa and a fracture toughness of 4.3±0.4 MPa m 1/2. 相似文献
2.
A series of the Ce 1−xCu xO 2−x/Al 2O 3/FeCrAl catalysts ( x = 0–1) were prepared. The structure of the catalysts was characterized using XRD, SEM and H 2-TPR. The catalytic activity of the catalysts for the combustion of methane was evaluated. The results indicated that in the Ce 1−xCu xO 2−x/Al 2O 3/FeCrAl catalysts the surface phase structure were the Ce 1−xCu xO 2−x solid solution, -Al 2O 3 and γ-Al 2O 3. The surface particle shape and size were different with the variety of the molar ratio of Ce to Cu in the Ce 1−xCu xO 2−x solid solution. The Cu component of the Ce 1−xCu xO 2−x/Al 2O 3/FeCrAl catalysts played an important role to the catalytic activity for the methane combustion. There were the stronger interaction among the Ce 1−xCu xO 2−x solid solution and the Al 2O 3 washcoats and the FeCrAl support. 相似文献
3.
Three supported La 0.8Sr 0.2MnO 3+x catalysts were prepared, one supported on lanthanum-stabilised alumina and two supported on a NiAl 2O 4 spinel. The catalysts were characterised using X-ray diffraction, transmission electron microscopy and surface area measurements following heat-treatments at temperatures up to 1200°C in air. In the alumina-supported catalyst, a reaction occurred between the active phase and the support at high temperatures, indicating that these materials would be unsuitable for high temperature catalytic combustion. Only in the NiAl 2O 4-supported catalysts were the supported perovskite phases found to be stable at high temperature. These catalysts showed good methane combustion activity. 相似文献
4.
The effect of the Pd addition method into the fresh Pd/(OSC + Al 2O 3) and (Pd + OSC)/Al 2O 3 catalysts (OSC material = Ce xZr 1−xO 2 mixed oxides) was investigated in this study. The CO + NO and CO + NO + O 2 model reactions were studied over fresh and aged catalysts. The differences in the fresh catalysts were insignificant compared to the aged catalysts. During the CO + NO reaction, only small differences were observed in the behaviour of the fresh catalysts. The light-off temperature of CO was about 20 °C lower for the fresh Pd/(OSC + Al 2O 3) catalyst than for the fresh (Pd + OSC)/Al 2O 3 catalyst during the CO + NO + O 2 reaction. For the aged catalysts lower NO reduction and CO oxidation activities were observed, as expected. Pd on OSC-containing alumina was more active than Pd on OSC material after the agings. The activity decline is due to a decrease in the number of active sites on the surface, which was observed as a larger Pd particle size for aged catalysts than for fresh catalysts. In addition, the oxygen storage capacity of the aged Pd/(OSC + Al 2O 3) catalyst was higher than that of the (Pd + OSC)/Al 2O 3 catalyst. 相似文献
5.
The reduction of NO x by hydrogen under lean burn conditions over Pt/Al 2O 3 is strongly poisoned by carbon monoxide. This is due to the strong adsorption and subsequent high coverage of CO, which significantly increases the temperature required to initiate the reaction. Even relatively small concentrations of CO dramatically reduce the maximum NO x conversions achievable. In contrast, the presence of CO has a pronounced promoting influence in the case of Pd/Al 2O 3. In this case, although pure H 2 and pure CO are ineffective for NO x reduction under lean burn conditions, H 2/CO mixtures are very effective. With a realistic (1:3) H 2:CO ratio, typical of actual exhaust gas, Pd/Al 2O 3 is significantly more active than Pt/Al 2O 3, delivering 45% NO x conversion at 160 °C, compared to >15% for Pt/Al 2O 3 under identical conditions. The nature of the support is also critically important, with Pd/Al 2O 3 being much more active than Pd/SiO 2. Possible mechanisms for the improved performance of Pd/Al 2O 3 in the presence of H 2+CO are discussed. 相似文献
6.
Mesostructured MnO x–Cs 2O–Al 2O 3 nanocomposites have been synthesized by reverse microemulsion method combined with hydrothermal treatment and then applied to the catalytic combustion of methane. Compared to impregnation-derived conventional MnO x/Cs 2O/Com-Al 2O 3 catalyst, the microemulsion-derived catalyst showed higher activity and stability for methane combustion. The T10% of the fresh and of the 72 h aged Mn xO–Cs 2O–Al 2O 3 were 475 and 490 °C, respectively, recommending it as a potential candidate catalyst for application in hybrid gas turbines. The homogeneous composition of the microemulsion-derived nanocomposite catalyst can hinder the loss of Cs + and accelerate the formation of Cs–β-alumina phase, ensuring thus higher activity and stability for methane combustion. 相似文献
7.
Structural, redox and catalytic deep oxidation properties of LaAl 1−xMn xO 3 ( x=0.0, 0.05, 0.1, 0.2, 0.4, 0.6, 0.8, 1.0) solid solutions prepared by the citrate method and calcined at 1073 K were investigated. XRD analysis showed that all the LaAl 1−xMn xO 3 samples are single phase perovskite-type solid solutions. Particle sizes and surface areas (SA) are in the 280–1180 Å and 4–33 m 2 g −1 ranges, respectively. Redox properties and the content of Mn 4+ were derived from temperature programmed reduction (TPR) with H 2. Two reduction steps are observed by TPR for pure LaMnO 3, the first attributed to the reduction of Mn 4+ to Mn 3+ and the second due to complete reduction of Mn 3+ to Mn 2+. The presence of Al in the LaAl 1−xMn xO 3 solid solutions produces a strong promoting effect on the Mn 4+→Mn 3+ reducibility and inhibits the further reduction to Mn 2+. Both for methane combustion and CO oxidation all Mn-containing perovskites are much more active than LaAlO 3, so pointing to the essential role of the transition metal ion in developing highly active catalysts. Partial dilution with Al appears to enhance the specific activity of Mn sites for methane combustion. 相似文献
8.
Combustion of CO, ethyl acetate and ethanol was studied over CuO x/Al 2O 3, CuO x–CeO 2/Al 2O 3, CuMn 2O 4/Al 2O 3 and Mn 2O 3/Al 2O 3 catalysts. It was found that modification of the alumina with ceria before subsequent copper oxide deposition increases the activity for combustion of CO substantially, but the effect of ceria was small on the combustion of ethyl acetate and ethanol. The activity increases with the CuO x loading until crystalline CuO particles are formed, which contribute little to the total active surface. The CuO x–CeO 2/Al 2O 3 catalyst is more active than the CuMn 2O 4/Al 2O 3 catalyst for the oxidation of CO but the CuMn 2O 4/Al 2O 3 catalyst is more active for the combustion of ethyl acetate and ethanol. Thermal ageing and water vapour in the feed caused a modest decrease in activity and did not affect the CuOx–CeO2/Al2O3 and CuMn2O4/Al2O3 catalysts differently. In addition, no difference in intermediates formed over the two catalysts was observed. Characterisation with XRD, FT-Raman and TPR indicates that the copper oxide is present as a copper aluminate surface phase on alumina at low loading. At high loading, bulk CuO crystallites are present as well. Modification of the alumina with ceria before the copper oxide deposition gives well dispersed copper oxide species and bulk CuO crystallites associated to the ceria, in addition to the two copper oxide species on the bare alumina. The distribution of copper species depends on the ceria and copper oxide loading. The alumina supported copper manganese oxide and manganese oxide catalysts consist mainly of crystalline CuMn2O4 and Mn2O3, respectively, on Al2O3. 相似文献
9.
A comparison study was carried out on non-thermal plasma (NTP)-assisted selective catalytic reduction (SCR) of NO x by propene over Ag/USY and Ag/Al 2O 3 catalysts. Ag/USY was almost inactive in thermal SCR while it showed obvious activities in NTP-assisted SCR at 100 °C–200 °C. Although the NO x conversion over Ag/Al 2O 3 was also enhanced at 300 °C–400 °C by the assistance of NTP, it was ineffective below 250 °C. The intermediates over Ag/USY and Ag/Al 2O 3 were investigated using in situ DRIFTS method. It was found that key intermediates in HC-SCR, such as NCO, CN, oxygenates and some N-containing organic species were enriched after the assistance of NTP. The differences in the behaviors of above intermediates were not found between these two kinds of catalysts. However, some evidences suggested that different properties of the absorbed NO x species resulted in the distinction of SCR reactions over Ag/USY and Ag/Al 2O 3. TPD profiles of Ag/Al 2O 3 showed that nitrates formed over the catalyst were quite stable at low temperatures, which might occupy the active sites and were unfavorable to SCR reactions. The nitrates over Ag/USY were unstable, among which the unidentate nitrate species is probably contributed to the SCR reactions at low temperatures. 相似文献
10.
The effects of carbon dioxide on the dehydrogenation of C 3H 8 to produce C 3H 6 were investigated over several Cr 2O 3 catalysts supported on Al 2O 3, active carbon and SiO 2. Carbon dioxide exerted promoting effects only on SiO 2-supported Cr 2O 3 catalysts. The promoting effects of carbon dioxide over a Cr 2O 3/SiO 2 catalyst were to enhance the yield of C 3H 6 and to suppress the catalyst deactivation. 相似文献
11.
In this study, a novel bifunctional catalyst IrFe/Al 2O 3, which is very active and selective for preferential oxidation of CO under H 2-rich atmosphere, has been developed. When the molar ratio of Fe/Ir was 5/1, the IrFe/Al 2O 3 catalyst performed best, with CO conversion of 68% and oxygen selectivity towards CO 2 formation of 86.8% attained at 100 °C. It has also been found that the impregnation sequence of Ir and Fe species on the Al 2O 3 support had a remarkable effect on the catalytic performance; the activity decreased following the order of IrFe/Al 2O 3 > co-IrFe/Al 2O 3 > FeIr/Al 2O 3. The three catalysts were characterized by XRD, H 2-TPR, FT-IR and microcalorimetry. The results demonstrated that when Ir was supported on the pre-formed Fe/Al 2O 3, the resulting structure (IrFe/Al 2O 3) allowed more metallic Ir sites exposed on the surface and accessible for CO adsorption, while did not interfere with the O 2 activation on the FeO x species. Thus, a bifunctional catalytic mechanism has been proposed where CO adsorbed on Ir sites and O 2 adsorbed on FeO x sites; the reaction may take place at the interface of Ir and FeO x or via a spill-over process. 相似文献
12.
The effectiveness of Ag/Al 2O 3 catalyst depends greatly on the alumina source used for preparation. A series of alumina-supported catalysts derived from AlOOH, Al 2O 3, and Al(OH) 3 was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet–visible (UV–vis) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, O 2, NO + O 2-temperature programmed desorption (TPD), H 2-temperature programmed reduction (TPR), thermal gravimetric analysis (TGA) and activity test, with a focus on the correlation between their redox properties and catalytic behavior towards C 3H 6-selective catalytic reduction (SCR) of NO reaction. The best SCR activity along with a moderated C 3H 6 conversion was achieved over Ag/Al 2O 3 (I) employing AlOOH source. The high density of Ag–O–Al species in Ag/Al 2O 3 (I) is deemed to be crucial for NO selective reduction into N 2. By contrast, a high C 3H 6 conversion simultaneously with a moderate N 2 yield was observed over Ag/Al 2O 3 (II) prepared from a γ-Al 2O 3 source. The larger particles of Ag mO ( m > 2) crystallites were believed to facilitate the propene oxidation therefore leading to a scarcity of reductant for SCR of NO. An amorphous Ag/Al 2O 3 (III) was obtained via employing a Al(OH) 3 source and 500 °C calcination exhibiting a poor SCR performance similar to that for Ag-free Al 2O 3 (I). A subsequent calcination of Ag/Al 2O 3 (III) at 800 °C led to the generation of Ag/Al 2O 3 (IV) catalyst yielding a significant enhancement in both N 2 yield and C 3H 6 conversion, which was attributed to the appearance of γ-phase structure and an increase in surface area. Further thermo treatment at 950 °C for the preparation of Ag/Al 2O 3 (V) accelerated the sintering of Ag clusters resulting in a severe unselective combustion, which competes with SCR of NO reaction. In view of the transient studies, the redox properties of the prepared catalysts were investigated showing an oxidation capability of Ag/Al 2O 3 (II and V) > Ag/Al 2O 3 (IV) > Ag/Al 2O 3 (I) > Ag/Al 2O 3 (III) and Al 2O 3 (I). The formation of nitrate species is an important step for the deNO x process, which can be promoted by increasing O 2 feed concentration as evidenced by NO + O 2-TPD study for Ag/Al 2O 3 (I), achieving a better catalytic performance. 相似文献
13.
The role of La 2O 3 loading in Pd/Al 2O 3-La 2O 3 prepared by sol–gel on the catalytic properties in the NO reduction with H 2 was studied. The catalysts were characterized by N 2 physisorption, temperature-programmed reduction, differential thermal analysis, temperature-programmed oxidation and temperature-programmed desorption of NO. The physicochemical properties of Pd catalysts as well as the catalytic activity and selectivity are modified by La2O3 inclusion. The selectivity depends on the NO/H2 molar ratio (GHSV = 72,000 h−1) and the extent of interaction between Pd and La2O3. At NO/H2 = 0.5, the catalysts show high N2 selectivity (60–75%) at temperatures lower than 250 °C. For NO/H2 = 1, the N2 selectivity is almost 100% mainly for high temperatures, and even in the presence of 10% H2O vapor. The high N2 selectivity indicates a high capability of the catalysts to dissociate NO upon adsorption. This property is attributed to the creation of new adsorption sites through the formation of a surface PdOx phase interacting with La2O3. The formation of this phase is favored by the spreading of PdO promoted by La2O3. DTA shows that the phase transformation takes place at temperatures of 280–350 °C, while TPO indicates that this phase transformation is related to the oxidation process of PdO: in the case of Pd/Al2O3 the O2 uptake is consistent with the oxidation of PdO to PdO2, and when La2O3 is present the O2 uptake exceeds that amount (1.5 times). La2O3 in Pd catalysts promotes also the oxidation of Pd and dissociative adsorption of NO mainly at low temperatures (<250 °C) favoring the formation of N2. 相似文献
14.
The reduction of NO under cyclic “lean”/“rich” conditions was examined over two model 1 wt.% Pt/20 wt.% BaO/Al 2O 3 and 1 wt.% Pd/20 wt.% BaO/Al 2O 3 NO x storage reduction (NSR) catalysts. At temperatures between 250 and 350 °C, the Pd/BaO/Al 2O 3 catalyst exhibits higher overall NO x reduction activity. Limited amounts of N 2O were formed over both catalysts. Identical cyclic studies conducted with non-BaO-containing 1 wt.% Pt/Al 2O 3 and Pd/Al 2O 3 catalysts demonstrate that under these conditions Pd exhibits a higher activity for the oxidation of both propylene and NO. Furthermore, in situ FTIR studies conducted under identical conditions suggest the formation of higher amounts of surface nitrite species on Pd/BaO/Al 2O 3. The IR results indicate that this species is substantially more active towards reaction with propylene. Moreover, its formation and reduction appear to represent the main pathway for the storage and reduction of NO under the conditions examined. Consequently, the higher activity of Pd can be attributed to its higher oxidation activity, leading both to a higher storage capacity ( i.e., higher concentration of surface nitrites under “lean” conditions) and a higher reduction activity ( i.e., higher concentration of partially oxidized active propylene species under “rich” conditions). The performance of Pt and Pd is nearly identical at temperatures above 375 °C. 相似文献
15.
Methane combustion over Pd/Al 2O 3 catalysts with and without added Pt and CeO 2 in both oxygen-rich and methane-rich mixtures at temperatures in the range 250–520°C has been investigated using a temperature-programmed reaction procedure with on-line gas analysis (FTIR). During the temperature loop under oxygen-rich conditions, there was an appreciable hysteresis in the activity of unmodified Pd/Al 2O 3, which was greatly enhanced over Pd–Pt/Al 2O 3. Over both catalysts the hysteresis was reversed under slightly methane-rich atmospheres, and as temperature was reduced, a sudden collapse or fluctuations in activity were shown respectively over Pd–Pt/Al 2O 3 and Pd/Al 2O 3. Such non-steady behaviour was almost eliminated over Pd/Al 2O 3–CeO 2. Under a very narrow range of conditions and over a Pd/Al 2O 3 packed bed, oscillation of methane combustion was observed. 相似文献
16.
A multi-component NO x-trap catalyst consisting of Pt and K supported on γ-Al 2O 3 was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H 2O and CO 2 on NO x storage. The Al 2O 3 support was shown to have NO x trapping capability with and without Pt present (at 250 °C Pt/Al 2O 3 adsorbs 2.3 μmols NO x/m 2). NO x is primarily trapped on Al 2O 3 in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO x/m 2, and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al 2O 3 catalyst are coordinated on the Al 2O 3 support at saturation. When 5% CO2 was included in a feed stream with 300 ppm NO and 12% O2, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H2O was included in a feed stream with 300 ppm NO and 12% O2, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al2O3-based nitrates decreased by 92%. Interestingly, with both 5% CO2 and 5% H2O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al2O3 destabilized the K–CO2 bond; specifically, H2O mitigates the NOx storage capacity losses associated with carboxylate competition. 相似文献
17.
The water-gas shift (WGS) activity of platinum catalysts dispersed on a variety of single metal oxides as well as on composite MO x/Al 2O 3 and MO x/TiO 2 supports (M = Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Y, Zr, La, Ce, Nd, Sm, Eu, Gd, Ho, Er, Tm) has been investigated in the temperature range of 150–500 °C, using a feed composition consisting of 3% CO an 10% H 2O. For Pt catalysts supported on single metal oxides, it has been found that both the apparent activation energy of the reaction and the intrinsic rate depend strongly on the nature of the support. In particular, specific activity of Pt at 250 °C is 1–2 orders of magnitude higher when supported on “reducible” compared to “irreducible” metal oxides. For composite Pt/MO x/Al 2O 3 and Pt/MO x/TiO 2 catalysts, it is shown that the presence of MO x results in a shift of the CO conversion curve toward lower reaction temperatures, compared to that obtained for Pt/Al 2O 3 or Pt/TiO 2, respectively. The specific reaction rate is in most cases higher for composite catalysts and varies in a manner which depends on the nature, loading, and primary crystallite size of dispersed MO x. Results are explained by considering that reducibility of small oxide particles increases with decreasing crystallite size, thereby resulting in enhanced WGS activity. Therefore, evidence is provided that the metal oxide support is directly involved in the WGS reaction mechanism and determines to a significant extent the catalytic performance of supported noble metal catalysts. Results of catalytic performance tests obtained under realistic feed composition, consisting of 3% CO, 10% H 2O, 20% H 2 and 6% CO 2, showed that certain composite Pt/MO x/Al 2O 3 and Pt/MO x/TiO 2 catalysts are promising candidates for the development of active WGS catalysts suitable for fuel cell applications. 相似文献
18.
Ni catalysts supported on γ-Al 2O 3, CeO 2 and CeO 2–Al 2O 3 systems were tested for catalytic CO 2 reforming of methane into synthesis gas. Ni/CeO 2–Al 2O 3 catalysts showed much better catalytic performance than either CeO 2- or γ-Al 2O 3-supported Ni catalysts. CeO 2 as a support for Ni catalysts produced a strong metal–support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO 2 had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/γ-Al 2O 3 catalysts for this reaction. A weight loading of 1–5 wt% CeO 2 was found to be the optimum. Ni catalysts with CeO 2 promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO 2-promoted catalysts are attributed to the oxidative properties of CeO 2. 相似文献
19.
The performance of unpromoted and MO x-(M: alkali (earth), transition metal and cerium) promoted Au/Al 2O 3 catalysts have been studied for combustion of the saturated hydrocarbons methane and propane. As expected, higher temperatures are required to oxidize CH 4 (above 400 °C), compared with C 3H 8 (above 250 °C). The addition of various MO x to Au/Al 2O 3 improves the catalytic activity in both methane and propane oxidation. For methane oxidation, the most efficient promoters to enhance the catalytic performance of Au/Al 2O 3 are FeO x and MnO x. For C 3H 8 oxidation a direct relationship is found between the catalytic performance and the average size of the gold particles in the presence of alkali (earth) metal oxides. The effect of the gold particle size becomes less important for additives of the type of transition metal oxides and ceria. The results suggest that the role of the alkali (earth) metal oxides is related to the stabilization of the gold nanoparticles, whereas transition metal oxide and ceria additives may be involved in oxygen activation. 相似文献
20.
Catalytic performance for partial oxidation of methane (POM) to synthesis gas was studied over the Rh/Al 2O 3 catalysts with Rh loadings between 0.1 and 3 wt%. It was found that the ignition temperature of POM reaction increased with the decreasing of the Rh loadings in the catalysts. For the POM reaction over the catalysts with high (≥1 wt%) Rh loadings, steady-state reactivity was observed. For the reaction over the catalysts with low (≤0.25 wt%) Rh loadings, however, oscillations in CH 4 and reaction products (CO, H 2, and CO 2) were observed. Comparative studies using H 2-TPR, O 2-TPD and high temperature in situ Raman spectroscopy techniques were carried out in order to elucidate the relation between the redox property of the Rh species in the Rh/Al 2O 3 with different Rh loadings and the performance of the catalysts for the reaction. Three kinds of oxidized rhodium species, i.e. the rhodium oxide species insignificantly affected by the support (RhO x), that intimately interacting with the Al 2O 3 surface (Rh iO x) and the Rh(AlO 2) y species formed by diffusion of rhodium oxides in to sublayers of Al 2O 3 [C.P. Hwang, C.T. Yeh, Q.M. Zhu, Catal. Today, 51 (1999) 93.], were identified by H 2-TPR and O 2-TPD experiments. Among them, the first two species can be easily reduced by H 2 at temperature below 350 °C, while the last one can only be reduced by H 2 at temperature above 500 °C. The ignition temperatures of POM reaction over the catalysts are closely related to the temperature at which most of the RhO x and Rh iO x species can be reduced by CH 4 in the reaction mixture. Compared to the Rh/Al 2O 3 with high Rh loadings, the catalysts with low Rh loadings contain more Rh iO x species which possess stronger RhO bond strength and are more difficult to be reduced than RhO x by the reaction mixture. Higher temperature is therefore required to ignite the POM reaction over the catalysts with lower Rh loadings. The oscillation during the POM reaction over the Rh/Al 2O 3 with low Rh loadings can be related to the behaviour of Rh(AlO 2) y species in the catalyst switching cyclically from the oxidized state to the reduced state during the reaction. 相似文献
|