Sintering additives regulated Cr ion charge state in Cr doped YAG transparent ceramics

Cr: YAG and Cr, Nd: YAG transparent ceramics have significant application prospects in solid state lasers, therefore a controllable charge state of Cr ion in Cr doped YAG transparent ceramics is necessary. In this study, a successful regulation of Cr charge state in both Cr, Nd: YAG and Cr: YAG transparent ceramics was achieved, by a simple optimizing the sintering additives. Both ceramics with the Cr doping concentration of 0.3?at% reached to the theoretical transmittance, after the vacuum sintering and the subsequent annealing process. It was found that by adopting silica additive, divalent charged Cr²⁺ ions could be detected from the vacuum sintered samples, and they were transferred into trivalent state after further annealing in air. Meanwhile, by vacuum sintering ceramics with divalent additives (CaO and MgO), a stable trivalent charged Cr ion could be obtained, and the subsequent air annealing process indicated a significant conversion from Cr³⁺ to Cr⁴⁺. Further increasing the Cr concentration was not benefit to the optical quality as well as the conversion of Cr³⁺ ion in Cr, Nd: YAG transparent ceramics.     

Effect of MgO doping on the structure and optical properties of YAG transparent ceramics

The paper studies the features of Mg²⁺ ions as sintering aid for reactive solid-state sintering of YAG transparent ceramics. Phase composition, microstructure and optical properties of YAG ceramics, doped by 0 ÷ 0.15 wt.% MgO, were investigated. Solubility limit of Mg²⁺ ions in YAG crystal lattice was found to be in the range of 0.06 ÷ 0.1 wt.% of MgO additive. Substitution mechanism of Mg²⁺ in ceramic YAG was identified by comparison of XRD data and ab initio calculation. It was shown that within the solubility limit Mg²⁺ ions most likely substitute Al³⁺ sites. Doping by MgO above solubility limit led to precipitation of spinel secondary phases. It was found that doping by Mg²⁺ ions increases concentration of oxygen vacancies in YAG lattice that effectively promote sintering. The optimal concentration range of MgO sintering aid that allow to achieve YAG transparent ceramics was defined as 0.03 ÷ 0.06 wt.%.     

Dy3+/Ce3+ Codoped YAG Transparent Ceramics for Single‐Composition Tunable White‐Light Phosphor

Superior optical, thermal, and mechanical properties of transparent ceramics are very important in the applications of solid lasers, solid‐state lighting, and transparent armors. Herein, a series of (Dy_0.03Ce_xY_0.97?x)₃Al₅O₁₂ transparent ceramics were fabricated using vacuum reactive sintering method. Importantly, these Dy³⁺/Ce³⁺ codoped yttrium aluminum garnet (YAG) transparent ceramics served as single‐composition tunable white‐light phosphors for UV‐LEDs is developed for the first time. By combining with commercially available UV‐LEDs directly, the optimal chromaticity coordinates and correlated color temperature (CCT) are (x = 0.33, y = 0.35) and 5609 K, respectively. Notably, the codoping of Ce³⁺ enhances the luminescent intensity of Dy³⁺ ions while excited at 327 nm. The emission color of YAG transparent ceramics can be tuned from white to yellow through energy transfer between Dy³⁺ and Ce³⁺. These new phosphors, possessing of pure CIE chromaticity and environmentally friendly nature, are promising for applications in white UV‐LEDs.     

Influence of Yb and Si on the fabrication of Yb:YAG transparent ceramics using spherical Y2O3 powders

Yb:YAG (yttrium aluminum garnet) transparent ceramics were fabricated by the solid-state method using monodispersed spherical Y₂O₃ powders as well as commercial Al₂O₃ and Yb₂O₃ powders. Pure YAG phase was obtained at low temperature due to homogeneous mixing of powders. Under the same sintering conditions, the Yb:YAG ceramics with different doping contents of Yb³⁺ had similar morphologies and densification rates. After being sintered at 1700 °C in vacuum, the ceramic samples had high transparencies. The Yb:YAG ceramics doped with 0.5 wt% SiO₂ formed Y–Si–O liquid phase and nonstoichiometric point defects that enhanced sintering. Compared with Nd doping, Yb doping hardly affected the YAG grain growth, sintering densification or optical transmittance, probably because Yb³⁺ easily entered the YAG lattice and had a high segregation coefficient.     

Assessment of conversion efficiency of Cr4+ ions by aliovalent cation additives in Cr:YAG ceramic for edge cladding

0.25at.% Cr:YAG ceramics were successfully fabricated as the edge cladding of Yb:YAG transparent ceramic slabs through vacuum sintering of co‐precipitated powders, using oxide additives to introduce different cations. The effects of various cation additives (Si⁴⁺, Ca²⁺, and Si⁴⁺ + Ca²⁺) on the conversion efficiency of Cr⁴⁺ ions and optical characteristics of the Cr:YAG edge cladding were investigated. Measurements of the absorption spectra of the Cr:YAG ceramics without any additives revealed 2 absorption bands centered at 430 nm and 600 nm, which imparted the sample with a green color. The introduction of only Si⁴⁺‐bearing additive did not promote the transition of Cr ions from the 3+ to 4+ state. Theoretical analysis and experimentation revealed that the addition of CaO not only enhanced the microstructure and improved the transmittance of the Cr:YAG ceramic, but also introduced vacancies that assisted in the formation of Cr⁴⁺ ions. It was determined that CaO has the same effect on the conversion efficiency of Cr⁴⁺ ions whether it is added as a single additive or in combination with SiO₂. The underlying mechanisms by which these aliovalent cation additives influence the formation of Cr⁴⁺ ions and affect optical properties are discussed in detail. High quality composite ceramics with Yb:YAG transparent ceramic slabs and dark brown‐colored Cr⁴⁺: YAG ceramic edge cladding were achieved through the addition of 0.05 wt.% CaO to the edge cladding, with no interfacial effects between the 2 regions being observed.     

Influence of Cr doping on the phase composition of Cr,Ca:YAG ceramics by solid state reaction sintering

In the present work, the influence of Cr and Ca co-additives on the phase formation under conditions emulated the real sintering process of Cr⁴⁺:YAG ceramics is studied. The XRD analysis of the treated samples revealed the difference in formation rates of intermediate phases between the samples with and without the Cr₂O₃ additive. The formation of intermediate phases in the solid-state reaction between Y₂O₃ and Al₂O₃ is observed to shift toward higher temperatures (ie, toward the stage of fast shrinkage) if the mixture of Cr₂O₃ and CaO is added. The reason for such shift is the appearance of new intermediate, which contains Cr⁴⁺ ions in perovskite structure, as has been established by optical absorption and luminescent investigations. It is found that the Cr,Ca:YAG ceramics prepared by vacuum solid state reaction sintering at 1750°C, 10 hours possesses better optical transparency than Ca:YAG ceramics prepared under the same conditions.     

Optical properties of YMASG:Ce fluorescent ceramics prepared by hot-pressure sintering

Cerium-doped yttrium aluminum garnet (YAG:Ce) based transparent ceramics have been widely used in fluorescent lighting as high-quality inorganic fluorescent conversion materials. This paper further explores the Mg²⁺-Si⁴⁺ ions doped YAG:Ce transparent ceramics by combining the solid-phase reaction method with vacuum hot-pressure sintering and implementing protection measures against hot-pressure mold contamination, and also investigates the effect of different Mg²⁺-Si⁴⁺ doping contents on the structure, transmittance and luminescence properties of the ceramics under hot-pressure sintering. In this work, pure-phase YMASG:Ce transparent fluorescent ceramics with a grain size of about 3-6 μm and clear and clean grain boundaries were obtained with an In-line transmittance of 67% at 800 nm. Under the excitation at 460 nm, the emission peak was red-shifted by 26 nm and the full width at half maxima (FWHM) was broadened with the increase of Mg²⁺-Si⁴⁺ content, which shows that the Mg²⁺-Si⁴⁺ ion pair effectively complements the absence of the red light component in the YAG:Ce emission spectrum. The optimized YMASG:Ce ceramics obtained high-quality warm white light with a low correlated color temperature (CCT) and a high color rendering index (CRI) under the excitation of the blue LED chip. This work proved the feasibility of vacuum hot-pressure sintering to prepare YMASG:Ce transparent fluorescent ceramics, and provided a new approach for studying YMASG:Ce-based ceramics, which was significant for the application of high-power visible laser illumination.     

Effect of complex Si4++Mg2+ additive on sintering and properties of undoped YAG ceramics

The paper is devoted to studying of Si⁴⁺+Mg²⁺ complex additive for obtaining transparent YAG ceramics for laser applications. Ceramics were fabricated by reactive vacuum sintering of commercial Y₂O₃, Al₂O₃ powders taken in a stoichiometric mixture with TEOS and MgO as sintering aids. Microstructure and optical properties of YAG:Si⁴⁺,Mg²⁺ ceramics were investigated as a function of the Si⁴⁺/Mg²⁺ ratio. It was found that the influence of complex additive does not correspond to the direct superposition of known Si⁴⁺- and Mg²⁺-induced sintering mechanisms and involves interaction between Si⁴⁺ and Mg²⁺ ions during sintering. It was shown that C_Si/C_Mg> 1 provides more effective pore elimination and uniform microstructure when C_Si/C_Mg< 1 gives more intense inhibition of grain grown which may be important for scaling the size of ceramics.     

Effect of air annealing on the optical properties and luminescence performance of Ce:YAG ceramics for light-emitting diodes at different Ce concentrations

(Y_1-x%Ce_x%)₃Al₅O₁₂ (x = 0.2,0.4,0.6,0.8,1.0) transparent ceramics were fabricated by vacuum sintering technology, followed by air annealing at different temperatures. Transmittance of ceramics, valence of cerium, and luminescent properties with varying annealing temperatures are studied in detail. The negative effect of Ce³⁺ oxidation induced by annealing gets increasingly evident when Ce concentration increases. Collaborating Ce:YAG ceramics with InGaN blue chips, light-emitting diodes (LEDs) with superior performance were constructed. The relationships between Ce concentration, annealing temperature, and luminous flux of LEDs are elucidated, showing that the optimized annealing temperature of Ce:YAG ceramics decreases from 1200 °C to 900 °C as Ce concentration increases from 0.2 at% to 1.0 at%. The luminous fluxes of optimized LEDs increase by ～10 % compared with that of unannealed LEDs.     

Annealing induced discoloration of transparent YAG ceramics using divalent additives in solid-state reaction sintering

Tetraethyl orthosilicate (TEOS) was commonly served as a sintering additive to promote the densification of transparent Y₃Al₅O₁₂ (YAG) ceramics. However, Si⁴⁺ that decomposed from TEOS would restrain the conversion of dopants into a higher valence state (e.g., Cr³⁺ → Cr⁴⁺). In this study, by using divalent sintering additives (CaO and MgO), the colorless and highly transparent YAG ceramics (T = 84.6%, at 1064 nm) were obtained after vacuum sintering at 1840 °C for 8 h and without subsequent annealing in air. An absorption peak centered at ∼320 nm was observed before annealing, and it extended to ∼550 nm after annealing at 1450 °C for 10 h in air. A discoloration phenomenon occurred and more scattering centers were observed with the formation of new [Mg/Ca²⁺F⁺] color centers. Air annealing did not improve the optical quality of the as-fabricated YAG ceramics with divalent dopants as sintering additives, owing to the formation of scattering centers.     

Single CaO accelerated densification and microstructure control of highly transparent YAG ceramic

In this work, a small amount of CaO single dopant was adopted to realize the densification and microstructure control of fine grained YAG ceramic with excellent optical quality, by a simple solid‐state reaction and one‐step vacuum sintering method. Then, highly transparent YAG ceramics (T = 84.4% at 1064 nm) were obtained just after vacuum sintering at 1820°C for 8 hours. The average grain size was only 2.7 μm, when the total amount of CaO was as low as 0.045 wt%. The effect of CaO on the microstructural evolution and optical property of the as‐fabricated YAG ceramics was systematically investigated in detail. It was found that CaO dopant promoted both densification and grain growth of YAG ceramics when the sintering temperature was lower than 1660°C, however, it dramatically inhibited grain growth when the sintering temperature was further increased.     

Highly-doped YAG:Sm3+ transparent ceramics: Effect of Sm3+ ions concentration

YAG:Sm³⁺ (3–15 at.%) transparent ceramics, a promising cladding material for suppressors of parasitic oscillations at 1064 nm of YAG:Nd³⁺ lasers, have been prepared by solid-state reactive sintering at 1725 °C. The effect of samarium ions concentration on the microstructure and optical properties of YAG:Sm³⁺ sintered ceramics was studied for the first time. The solubility limit of samarium ions in the garnet matrix was found to lie within the range of 9–11 at.%. The spectroscopic characterization of YAG:Sm³⁺ (3–15 at.%) ceramic samples showed that the absorption coefficients corresponding to Sm³⁺ ions transitions increased linearly with increasing Sm³⁺ doping. Also, the increase in the concentration of Sm³⁺ ions contributes to the increase in the intensities of the satellites, leading to the broadening of the main spectral lines and implicitly to the increase of the absorption coefficient around 1064 nm. It was shown that YAG:Sm³⁺ ceramics doped with 9 at.% Sm³⁺ ions possess optical losses of 0.07 cm^?1 at 808 nm and an optical absorption coefficient of 4.45 cm^?1 at 1064 nm. The concentration dependence of the ⁴G_5/2 level decay confirmed that the luminescence extinction is due to the energy transfer between the Sm³⁺ ions through cross-relaxation processes. All these results show that highly-doped YAG:Sm³⁺ (9 at.%) ceramics could be the best candidate for parasitic oscillation suppression in high-power YAG:Nd³⁺ lasers at 1064 nm.     

Fabrication of Ce:YAG,Ce,Cr:YAG and Ce:YAG/Ce,Cr:YAG dual-layered composite phosphor ceramics for the application of white LEDs

(Ce_0.001Y_0.999)₃Al₅O₁₂ and (Ce_0.001Y_0.999)₃(Cr_xAl_1−x)₅O₁₂ (x=0.001−0.005) transparent ceramics were synthesized by the solid state reaction and vacuum sintering and their optical properties were measured. High quality white light was obtained when the Ce:YAG/Ce,Cr:YAG dual-layered composite ceramic was directly combined with commercial blue LED chip. A maximum luminous efficacy exceeding 76 lm/W at a low correlated color temperature of 4905 K was obtained. The color temperature can be controlled by variations of Cr³⁺ concentration and the ceramic thickness. Hence, the Ce:YAG/Ce,Cr:YAG dual-layered composite phosphor ceramic may be a promising candidate for white LEDs.     

The effect of silica doping on neodymium diffusion in yttrium aluminum garnet ceramics: implications for sintering mechanisms

The Nd³⁺ cation diffusion into transparent polycrystalline YAG (Y₃Al₅O₁₂) was investigated as a function of temperature and silica content. Thin neodymium oxide layers were deposited on sintered YAG substrates prior to annealing under air at temperatures from 1400 to 1600 °C. Bulk and grain boundary neodymium diffusion coefficients were measured by secondary ion mass spectrometry. The experimental results show that silica addition increases the diffusivity of Nd³⁺ by a factor 10 whatever the diffusion path, probably as a result of extrinsic point defects formation, especially rare-earth vacancies.The experimental diffusion data were used to elucidate the sintering mechanism of Nd:YAG ceramics in the temperature range 1450–1550 °C. Firstly, it appeared that the intermediate stage of solid-state sintering should be controlled by the rare-earth diffusion along the grain boundary with an activation energy of about 600 kJ mol^?1. Secondly, grain growth mechanism at the final stage of liquid-phase sintering was investigated for silica-doped Nd:YAG samples. Thus, the grain growth should be limited by the reaction at interfaces at a temperature lower than 1500 °C, with an activation energy of about 880 kJ mol^?1. At higher temperature, it seems to be limited by the ionic diffusion through the intergranular liquid phase, with an activation energy of 250 kJ mol^?1.     

Solubility limit of Si in YAG at 1700 °C in vacuum

Measurement of the solubility limit of Si in yttrium aluminum garnet (YAG-Y₃Al₅O₁₂) is crucial for understanding the mechanisms by which Si influences grain boundary mobility, and the mechanisms by which grain boundaries migrate. In the present work, the solubility limit of Si in YAG at 1700 °C in vacuum (5 × 10⁻⁶ Torr), which are the most common sintering temperature and environment for YAG, was measured for the first time. Measurements were conducted by wavelength dispersive spectroscopy (WDS), using polished YAG specimens with 3700 ppm Si (0.8 wt% SiO₂). Si content to ensure saturation with Si. The accuracy of the WDS result was confirmed by using a series of doped specimens and by comparing to inductively coupled plasma mass spectrometry ICP-MS results. The results indicate that the solubility limit of Si in YAG at 1700 °C (5 × 10⁻⁶ Torr), is 980 ± 60 ppm. The measured Si solubility was found to significantly depend on the cooling rate, where for furnace cooled specimens the measured Si solubility was 650 ± 60 ppm. A second phase in triple junction was repeatedly observed when higher content of Si was used, confirming this work results.     

Pump laser induced photodarkening in ZrO2-doped Yb:Y2O3 laser ceramics

5 at.% Yb:Y₂O₃ transparent ceramics were fabricated using vacuum sintering plus HIP. The ceramics doped with 1 at.% ZrO₂ as the sintering additive were densified at 1700 °C in vacuum followed by HIPing at 1775 °C, while those without sintering additives were densified at 1520 °C in vacuum followed by HIPing at 1450 °C. After sintering, both ceramics had relatively high in-line transmittance. However, during laser experiments, the ZrO₂-doped Yb:Y₂O₃ (Zr-YbY) ceramics were photodarkened when irradiated by 940 nm pump light. The discoloration might be attributed to the formation of Zr³⁺ color centers during lasing. In contrast, no photodarkening effect was detected in the pure Yb:Y₂O₃ ceramics without sintering additives (P-YbY). The P-YbY ceramics exhibited much higher lasing efficiency (17%) than the Zr-YbY ceramics (9%). To our best knowledge, it is the first time that the photodarkening effect was detected in rare-earth doped sesquioxide laser ceramics.     

Influence of calcium concentration on formation of tetravalent chromium doped Y3Al5O12 ceramics

Yttrium Aluminium Garnet (YAG) ceramics doped with chromium were prepared by solid-state reactive sintering in a vacuum. The influence of the charge compensator Ca²⁺ concentration on microstructure, optical properties and efficacy of Cr³⁺ oxidation to Cr⁴⁺ under air annealing was investigated. A non-monotonic dependence of these features on the amount of CaO as an additive was found. The changes in ceramic transparency and microstructure were explained considering the interaction between CaO and Cr₂O₃ at the ceramic grain boundaries, which leads to a different pore evolution in distinct samples during sintering. The efficacy of the oxidation of Cr³⁺ to Cr⁴⁺ strongly depends on the concentration of Ca dissolved in the YAG. The calcium solubility decreases due to the higher oxygen partial pressure of the extra phases on the grain boundaries that decreases the amount of generated Cr⁴⁺ ions. Such phenomenon explains the lower concentration of Cr⁴⁺ ions in the sample with 0.8% of Ca against the one with 0.5%. The experiment shows that the ceramic with 0.5% of Ca has a better in-line transmission and a higher concentration of Cr⁴⁺ ions in comparison with samples with a different Ca concentration.     

Effects of Gd Substitution on Sintering and Optical Properties of Highly Transparent (Y0.95−xGdxEu0.05)2O3 Ceramics

Highly transparent (Y_0.95?xGd_xEu_0.05)₂O₃ (x = 0.15–0.55) ceramics have been fabricated by vacuum sintering at the relatively low temperature of 1700°C for 4 h with the in‐line transmittances of 73.6%–79.5% at the Eu³⁺ emission wavelength of 613 nm (~91.9%–99.3% of the theoretical transmittance of Y_1.34Gd_0.6Eu_0.06O₃ single crystal), whereas the x = 0.65 ceramic undergoes a phase transformation at 1650°C and has a transparency of 53.4% at the lower sintering temperature of 1625°C. The effects of Gd³⁺ substitution for Y³⁺ on the particle characteristics, sintering kinetics, and optical performances of the materials were systematically studied. The results show that (1) calcining the layered rare‐earth hydroxide precursors of the ternary Y–Gd–Eu system yielded rounded oxide particles with greatly reduced hard agglomeration and the particle/crystallite size slightly decreases along with increasing Gd³⁺ incorporation; (2) in the temperature range 1100°C–1480°C, the sintering kinetics of (Y_0.95?xGd_xEu_0.05)₂O₃ is mainly controlled by grain‐boundary diffusion with similar activation energies of ~230 kJ/mol; (3) Gd³⁺ addition promotes grain growth and densification in the temperature range 1100°C–1400°C; (4) the bandgap energies of the (Y_0.95?xGd_xEu_0.05)₂O₃ ceramics generally decrease with increasing x; however, they are much lower than those of the oxide powders; (5) both the oxide powders and the transparent ceramics exhibit the typical red emission of Eu³⁺ at ~613 nm (the ⁵D₀→⁷F₂ transition) under charge transfer (CT) excitation. Gd³⁺ incorporation enhances the photoluminescence and shortens the fluorescence lifetime of Eu³⁺.     

Effect of Ca2+ and Mg2+ ions on the sintering and spectroscopic properties of cr-doped yttrium aluminum garnet ceramics

In this work, we investigated the effects of Ca²⁺ and Mg²⁺ ions and annealing temperature on the spectroscopic parameters of chromium-doped yttrium aluminum garnet ceramics (Cr:YAG). Samples were obtained with either a separate or a simultaneous addition of calcium and magnesium oxides. To achieve this, aqueous suspensions were prepared using Y₂O₃, Al₂O₃, Cr₂O₃, MgO, and CaO high-purity powders as raw materials. The obtained suspensions were freeze-granulated, pressed into pellets, debinded, and subjected to reactive sintering in vacuum at 1715°C for 6 h. Each material was annealed in air with temperatures between 1300 and 1700°C. Samples were also compared to Cr:YAG ceramics with the addition of silica as a sintering aid. All the materials obtained were then exposed to 445 nm excitation, and emission spectra in the visible and infrared wavelengths were recorded. The results showed that the emission spectra of Cr:YAG ceramics varied according to the annealing conditions: as-sintered samples exhibited strong emissions of around 680 nm and, after air annealing, of around 1400 nm. This phenomenon is attributed to the Cr³⁺→Cr⁴⁺ transition. Samples doped solely with MgO exhibited the highest emission intensity in the infrared region. Thus, Mg²⁺ ions provided the best conversion efficiency of chromium ions.     

Effects of Sintering Aids on the Transparency and Conversion Efficiency of Cr4+ Ions in Cr: YAG Transparent Ceramics

Tetravalent chromium‐doped Y₃Al₅O₁₂ ceramics were fabricated by solid‐state reactive sintering method using high‐purity Y₂O₃, α‐ Al₂O₃, and Cr₂O₃ powders as the starting materials. CaO and MgO were co‐doped as the sintering aids. The effects of TEOS and divalent dopants (CaO and MgO) on the optical qualities, the conversion efficiency of Cr⁴⁺ ions, and the microstructure evolutions of 0.1 at.% Cr⁴⁺: YAG ceramics were investigated. Fully dense, dark brown colored Cr⁴⁺: YAG ceramics with an average grain size of 3.1 μm were achieved. The in‐line transmittance of the as‐prepared ceramic at 2000 nm was 85.3% (4 mm thick), and the absorption coefficient at 1030 nm (the characteristic absorption peak of Cr⁴⁺ ions) was as high as 3.7 cm^?1, which was higher than that of corresponding single crystals fabricated by Czochralski method.