Reactive blending of poly(L‐lactic acid) with poly(ethylene‐co‐vinyl alcohol)

Poly(L ‐lactic acid) (PLLA) was blended with poly(ethylene‐co‐vinyl alcohol) (EVOH) in the presence of an esterification catalyst to induce reaction between the hydroxyl groups of EVOH and the terminal carboxylic group of PLLA. Nascent low‐molecular‐weight PLLA, obtained from a direct condensation polymerization of L ‐lactic acid in bulk state, was used for the blending. Domain size of the PLLA phase in the graft copolymer was much smaller than that corresponding to a PLLA/EVOH simple blend. The mechanical properties of the graft copolymer were far superior to those of the simple blend, and the graft copolymer exhibited excellent mechanical properties even though the biodegradable fraction substantially exceeded the percolation level. The grafted PLLA reduced the crystallization rate of the EVOH moiety. Melting peak temperature (T_m) of the PLLA phase was not observed until the content of PLLA in the graft reaction medium went over 60 wt %. The modified Sturm test results demonstrated that biodegradation of EVOH‐g‐PLLA took place more slowly than that of an EVOH/PLLA simple blend, indicating that the chemically bound PLLA moiety was less susceptible to microbial attack than PLLA in the simple blend. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 886–890, 2005     

Synthesis and thermal properties of poly(methyl methacrylate)‐poly(L‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer

Poly(methyl methacrylate)‐poly(L ‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer was prepared using atom transfer radical polymerization (ATRP). The structure and properties of the copolymer were analyzed using infrared spectroscopy, gel permeation chromatography, nuclear magnetic resonance (¹H‐NMR, ¹³C‐NMR), thermogravimetry, and differential scanning calorimetry. The kinetic plot for the ATRP of methyl methacrylate using poly(L ‐lactic acid) (PLLA) as the initiator shows that the reaction time increases linearly with ln[M]₀/[M]. The results indicate that it is possible to achieve grafted chains with well‐defined molecular weights, and block copolymers with narrowed molecular weight distributions. The thermal stability of PLLA is improved by copolymerization. A new wash‐extraction method for removing copper from the ATRP has also exhibits satisfactory results. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Preparation of high‐molecular‐weight poly(L‐lactic acid)‐based polymers through direct condensation polymerization in bulk state

Poly(L ‐lactic acid‐co‐succinic acid‐co‐1,4‐butanediol) (PLASB) was synthesized by a direct condensation copolymerization of L ‐lactic acid, succinic acid (SA), and 1,4‐butanediol (BD) in bulk state using titanium(IV) butoxide (TNBT) as a catalyst. Weight average molecular weight (M_w) of PLASB increased from 3.5 × 10⁴ to 2.1 × 10⁵ as the content of SA and BD went up from 0.01 to 0.5 mol/100 mol of L ‐lactic acid (LA). PLASB having M_w in the range from 1.8 × 10⁵ to 2.1 × 10⁵ showed tensile properties comparable to those of commercially available poly(L ‐lactic acid) (PLLA). In sharp contrast, homopolymerization of LA in bulk state produced PLLA with M_w as low as 4.1 × 10⁴, and it was too brittle to prepare specimens for the tensile tests. M_w of PLASB synthesized by using titanium(IV)‐2‐ethyl(hexoxide), indium acetate, indium hydroxide, antimony acetate, antimony trioxide, dibutyl tin oxide, and stannous‐2‐ethyl 1‐hexanoate was compared with that of PLASB obtained by TNBT. Ethylene glycol oligomers with different chain length were added to LA/SA in place of BD to investigate effect of chain length of ethylene glycol oligomers on the M_w of the resulting copolymers. Biodegradability of PLASB was analyzed by using the modified Sturm test. Toxicity of PLASB was evaluated by counting viable cell number of mouse fibroblast cells that had been in contact with PLASB discs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 466–472, 2006     

Synthesis and characterization of star‐shaped poly(ethylene glycol)‐block‐poly(L‐lactic acid) copolymers by melt polycondensation

Compared with linear diblock or triblock poly(ethylene glycol)‐block‐poly(L ‐lactic acid) copolymer (PEG‐b‐PLLA), star‐shaped PEG‐b‐PLLA (sPEG‐b‐PLLA) copolymers exhibit smaller hydrodynamic radius and lower viscosity and are expected to display peculiar morphologies, thermal properties, and degradation profiles. Compared with the synthesis routine of PEG‐b‐PLLA form lactide and PEG, the traditional synthesis routine from LA and PEG were suffered by the low reaction efficiency, low purity, lower molecular weight, and wide molecular weight distribution. In this article, multiarm sPEG‐b‐PLLA copolymer was prepared from multiarm sPEG and L ‐lactic acid (LLA using an improved method of melt polycondensation, in which two types of sPEG, that is, sPEG₁ (four arm, Mn = 4300) and sPEG₂ (three arm, Mn = 3200) were chosen as the core. It was found the molecular weight of sPEG‐b‐PLLA could be strongly affected by the purity of LLA and sPEGs, and the purification technology of vacuum dewater and vacuum distillation could help to remove most of the impurities in commercial available LLA. The polymers, including sPEG and sPEG‐b‐PLLA with varied core (sPEG₁ and sPEG₂) and LLA/sPEG feeding ratios, were characterized and confirmed by ¹H‐NMR and ¹³C‐NMR spectroscopy, Fourier transform infrared spectroscopy (FT‐IR) and gel permeation chromatography, which showed that the terminal hydroxyl group in each arm of sPEGs had reacted with LLA to form sPEG‐b‐PLLA copolymers with fairly narrow molecular weight distribution. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Melt polycondensation of L‐lactic acid catalyzed by 1,3‐dialkylimidazolium ionic liquids

BACKGROUND: In syntheses of biodegradable and bioresorbable polymers, efficient metal‐free catalysts are very desirable as the resulting products may be more biocompatible. As an attempt to find new metal‐free catalysts, 1,3‐dialkylimidazolium salts, the most commonly used ionic liquids or organic melt salts, were used as single‐component catalysts in the melt polycondensation of L ‐lactic acid for the first time. The resulting poly(L ‐lactic acid) (PLLA) was characterized using gel permeation chromatography, ¹³C NMR, DSC and polarimetry. RESULTS: It has been found that less bulky substituents on the imidazolium ring are conducive to catalytic activity. PLLA with molar mass of about 20 000 g mol^?1 was synthesized at high yield (over 70%) in the presence of various 1,3‐dialkylimidazolium salts. The product exhibits satisfactory color (white to slightly yellow), optical purity (89–95%) and crystallinity (40–55%). A possible catalytic mechanism is proposed. CONCLUSION: As compared with the well‐known binary catalyst system SnCl₂ · 2H₂O/toluene sulfonic acid, the catalysts used in this investigation are better in terms of increasing PLLA yield and preventing discoloration and comparable in terms of racemization. Copyright © 2008 Society of Chemical Industry     

Effect of pH,ionic strength,and temperature on uranyl ion adsorption by poly(N‐vinyl 2‐pyrrolidone‐g‐tartaric acid) hydrogels

Poly‐electrolyte N‐vinyl 2‐pyrrolidone‐g‐tartaric acid (PVP‐g‐TA) hydrogels with varying compositions were prepared in the form of rods from ternary mixtures of N‐vinyl 2‐pyrrolidone/tartaric acid/water. The effect of external stimuli, such as the solution pH, ionic strength, and temperature, on uranyl adsorption by these hydrogels was investigated. Uranyl adsorption capacities of the hydrogels were determined to be 53.2–72.2 (mg UO/g dry gel) at pH 1.8, and 35.3–60.7 (mg UO/g dry gel) at pH 3.8, depending on the amount of TA in the hydrogel. The adsorption studies have shown that the temperature and the ionic strength of the swelling solution also influence uranyl ion adsorption by PVP‐g‐TA hydrogels. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2219–2226, 2000     

Highly enhanced accelerating effect of melt‐recrystallized stereocomplex crystallites on poly(L‐lactic acid) crystallization: effects of molecular weight of poly(D‐lactic acid)

The effects of the molecular weight of poly(D ‐lactic acid) (PDLA), which forms stereocomplex (SC) crystallites with poly(L ‐lactic acid) (PLLA), and those of processing temperature T_p on the acceleration (or nucleation) of PLLA homocrystallization were investigated using PLLA films containing 10 wt% PDLA with number‐average molecular weight (M_n) values of 5.47 × 10⁵, 9.67 × 10⁴ and 3.67 × 10⁴ g mol^–1 (PDLA‐H, PDLA‐M and PDLA‐L, respectively). For the PLLA/PDLA‐H and PLLA/PDLA‐M films, the SC crystallites that were ‘non’‐melted and those that were ‘completely’ melted at T_p values just above their endset melting temperature and recrystallized during cooling were found to act as effective accelerating (or nucleation) agents for PLLA homocrystallization. In contrast, SC crystallites formed from PDLA‐L, having the lowest M_n, were effective accelerating agents without any restrictions on T_p. In this case, the accelerating effects can be attributed to the plasticizer effect of PDLA‐L with the lowest M_n. The accelerating effects of SC crystallites in the PLLA/PDLA‐H and PLLA/PDLA‐M films was dependent on crystalline thickness for T_p values below the melting peak temperature of SC crystallites, whereas for T_p values above the melting peak temperature the accelerating effects are suggested to be affected by the interaction between the SC crystalline regions and PLLA amorphous regions.     

Melting behavior of poly(trimethylene terephthalate)

In this study, the melting behavior of isothermally crystallized polytri‐ methylene terephthalate (PTT) was investigated. Multiple melting behaviors in DSC heating trace were found because two populations of lamellar stacks were formed during primary crystallization and the recrystallization at heating process, respectively. This fact could be also confirmed from the result of optical microscopy observation. The Hoffman–Weeks equation was applied to obtain equilibrium melting temperature (T). The T value of PTT is about 525 K, which is 10 K higher than that reported. Combining the enthalpy of fusion from the DSC result and the degree of crystallinity from WAXD result, the value of the equilibrium‐melting enthalpy ΔH was deduced to be approximately 28.8 kJ mol^?1. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2426–2433, 2002     

Photodegradation of Poly(L‐lactic acid): Effects of Photosensitizer

Summary: Amorphous and crystallized poly(L ‐lactic acid) (PLLA‐A and PLLA‐C, respectively) films with different contents of N,N,N′,N′‐tetramethyl‐1,4‐phenylenediamine (TMPD) as a photosensitizer were prepared, and the effects of the addition of TMPD on the photodegradation of PLLA films were investigated. It was found that the addition of TMPD effectively enhanced the photodegradation of PLLA films and thereby decreased their molecular weight of PLLA films regardless of their crystallinity, and that PLLA films with different molecular weights can be prepared by the addition of different amounts of TMPD and subsequent UV irradiation. Too high contents of TMPD however caused the brittleness of PLLA films due to a large decrease in molecular weight. The PLLA chains in crystalline regions as well as those in amorphous regions are photodegradable even at an early stage, in marked contrast to their hydrolytic degradation, where the chains in the amorphous regions are selectively degraded. The basic changes in glass transition, cold crystallization, and melting temperatures (T_g, T_cc, and T_m, respectively) of PLLA films during UV irradiation can be ascribed to low‐temperature annealing effects; i.e., annealing‐induced stabilization in chain packing should have elevated T_g, and annealing‐induced formation of crystallite nuclei should have lowered T_cc and increased T_m. The exceptional large decreases in T_cc and T_m of UV‐irradiated PLLA‐A films and in T_g of UV‐irradiated PLLA‐C films at high TMPD contents are attributable to the large decrease in molecular weight, whereas the exceptional decrease in T_m of PLLA‐C films at high TMPD contents can be due to the folding surface structural change of crystalline regions or to the lattice disorder caused by molecular structural changes.

of PLLA‐A films before UV irradiation and after UV irradiation for 60 h as a function of TMPD content.     

Porous biodegradable polyester blends of poly(L‐lactic acid) and poly(ε‐caprolactone): physical properties,morphology, and biodegradation

Poly(L ‐lactic acid) (PLLA), poly(ε‐caprolactone) (PCL), and their films without or blended with 50 wt% poly(ethylene glycol) (PEG) were prepared by solution casting. Porous films were obtained by water‐extraction of PEG from solution‐cast phase‐separated PLLA‐blend‐PCL‐blend‐PEG films. The effects of PLLA/PCL ratio on the morphology of the porous films and the effects of PLLA/PCL ratio and pores on the physical properties and biodegradability of the films were investigated. The pore size of the blend films decreased with increasing PLLA/PCL ratio. Polymer blending and pore formation gave biodegradable PLLA‐blend‐PCL materials with a wide variety of tensile properties with Young's modulus in the range of 0.07–1.4 GPa and elongation at break in the range 3–380%. Pore formation markedly increased the PLLA crystallinity of porous films, except for low PLLA/PCL ratio. Polymer blending as well as pore formation enhanced the enzymatic degradation of biodegradable polyester blends. Copyright © 2006 Society of Chemical Industry     

Relationship between the crystallization behavior of poly(ethylene glycol) and stereocomplex crystallization of poly(L‐lactic acid)/poly(D‐lactic acid)

Poly(l ‐lactic acid) (PLLA) is a good biomedical polymer material with wide applications. The addition of poly(ethylene glycol) (PEG) as a plasticizer and the formation of stereocomplex crystals (SCs) have been proved to be effective methods for improving the crystallization of PLLA, which will promote its heat resistance. In this work, the crystallization behavior of PEG and PLLA/poly(d ‐lactic acid) (PDLA) in PLLA/PDLA/PEG and PEG‐b‐PLLA/PEG‐b‐PDLA blends has been investigated using differential scanning calorimetry, polarized optical microscopy and X‐ray diffraction. Both SCs and homocrystals (HCs) were observed in blends with asymmetric mass ratio of PLLA/PDLA, while exclusively SCs were observed in blends with approximately equal mass ratio of PLLA/PDLA. The crystallization of PEG was only observed for the symmetric blends of PLLA_39k/PDLA_35k/PEG_2k, PLLA_39k/PDLA_35k/PEG_5k, PLLA_69k/PDLA_96k/PEG_5k and PEG‐b‐PLLA_31k/PEG‐b‐PDLA_27k, where the mass ratio of PLLA/PDLA was approximately 1/1. The results demonstrated that the formation of exclusively SCs would facilitate the crystallization of PEG, while the existence of both HCs and SCs could restrict the crystallization of PEG. The crystallization of PEG is related to the crystallinity of PLLA and PDLA, which will be promoted by the formation of SCs. © 2017 Society of Chemical Industry     

Thermally induced crystallization and enzymatic degradation studies of poly (L‐lactic acid) films

Poly(L ‐lactic acid) (PLLA) films with different crystallinities were prepared by solvent casting and subsequently annealed at various temperatures (T_a) (80–110°C). The effects of crystallinity on enzymatic degradation of PLLA films were examined in the presence of proteinase K at 37°C by means of weight loss, DSC, FTIR spectroscopy, and optical microscopy. DSC and the absorbance ratio of 921 and 956 cm^?1 (A₉₂₁/A₉₅₆) were used to evaluate crystallinity changes during thermally induced crystallization and enzymatic hydrolysis. The highest percentage of weight loss was observed for the film with the lowest initial crystallinity and the lowest percentage of weight loss was observed for the film with highest crystallinity. FTIR investigation of degraded films showed a band at 922 cm^?1 and no band at 908 cm^?1 suggested that all degraded samples form α crystals. The rate of degradation was found to depend on the initial crystallinity of PLLA film and shown that enzymatic degradation kinetics followed first‐order kinetics for a given enzyme concentration. DSC crystallinity and IR absorbance ratio, A₉₂₁/A₉₅₆ ratio, showed no significant changes with degradation time for annealed PLLA films whereas as‐cast PLLA film showed an increase in crystallinity with degradation; this revealed that degradation takes place predominantly in the free amorphous region of annealed PLLA films without changing long range and short range order © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

The effect of gel composition on the uranyl ions adsorption capacity of poly(N‐vinyl 2‐pyrrolidone‐g‐citric acid) hydrogels prepared by gamma rays

Poly(N‐vinyl 2‐pyrrolidone‐g‐citric acid) (PVP‐g‐CA) hydrogels with varying compositions were prepared from ternary mixtures of N‐vinyl 2‐pyrrolidone–citric acid–water by using ⁶⁰Co γ‐rays. The effect of gel composition on the uranyl ions adsorption capacity of PVP‐g‐CA hydrogels was investigated. Uranyl adsorption capacity of these hydrogels were found to be in the range of 18–144 mg [UO]/g dry gel from the aqueous solution of uranyl nitrate and 22–156 mg [UO]/g dry gel from the aqueous solution of uranyl acetate, depending on the content of citric acid in the hydrogel, while poly(N‐vinyl 2‐pyrrolidone) hydrogel did not sorb any uranyl ion. The swelling of PVP‐g‐CA hydrogel containing 2.7 mol % CA was observed in water (1620%), in uranyl acetate solution (1450%) and in uranyl nitrate solution (1360%), as compared to 700% swelling of pure PVP hydrogels. The diffusion coefficients were varied from 12.57 up to 4.04 • 10⁻⁸ m² s⁻¹. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1037–1043, 2000     

Stereocomplex formation between poly(L‐lactic acid) and poly(D‐lactic acid) with disproportionately low and high molecular weights from the melt

Poly(L ‐lactic acid) (PLLA) and poly(D ‐lactic acid) (PDLA) with very different weight‐average molecular weights (M_w) of 4.0 × 10³ and 7.0 × 10⁵ g mol^?1 (M_w(PDLA)/M_w(PLLA) = 175) were blended at different PDLA weight ratios (X_D = PDLA weight/blend weight) and their crystallization from the melt was investigated. The presence of low molecular weight PLLA facilitated the stereocomplexation and thereby lowered the cold crystallization temperature (T_cc) for non‐isothermal crystallization during heating and elevated the radial growth rate of spherulites (G) for isothermal crystallization, irrespective of X_D. The orientation of lamellae in the spherulites was higher for the neat PLLA, PDLA and an equimolar blend than for the non‐equimolar blends. It was found that the orientation of lamellae in the blends was maintained by the stereocomplex (SC) crystallites. Although the G values are expected to decrease with an increase in X_D or the content of high‐molecular‐weight PDLA with lower chain mobility compared with that of low‐molecular‐weight PLLA, G was highest at X_D = 0.5 where the maximum amount of SC crystallites was formed and the G values were very similar for X_D = 0.4 and X_D = 0.6 with the same enantiomeric excess. This means that the effect of SC crystallites overwhelmed that of chain mobility. The nucleating mechanisms of SC crystallites were identical for X_D = 0.1–0.5 in the T_c range 130–180 °C. Copyright © 2011 Society of Chemical Industry     

Electrochemical synthesis and properties of poly(3‐methylthiophene): Novel synthesis of poly(3‐methylthiophene) with pentachlorostannate and hexachloroantimonate

Poly(3‐methylthiophene) (P3‐MeT) doped with different anions were prepared electrochemically in the presence of tetraalkylammonium salts. The new poly(3‐methylthiophene) SnCl and SbCl (P3‐MeT SnCl₅ and P3‐MeT SbCl₆) were prepared electrochemically using tetra‐n‐butylammonium pentachlorostannate and tetra‐n‐butylammonium hexachloroantimonate as the supporting electrolytes. The effect of current density, salt concentration, reaction temperature, and the nature of solvents on the polymer yield and polymer conductivities have been investigated. Cyclic voltammetry of poly(3‐methylthiophene) has been examined at platinum electrode in 1,2‐dichloroethane medium containing n‐Bu₄NSnCl₅, Bu₄NSbCl₆, and Bu₄NClO₄ as the supporting electrolytes in the range of −1.0 to 1.7 V versus SCE in the presence and absence of 3‐methylthiophene. Electrical conductivity, magnetic susceptibility measurements, and structural determination by elemental analysis and infrared studies were also made. Scanning electron microscopy revealed a globular, branched, fibrous and a spongy, fibrous morphology of poly(3‐methylthiophene) SnCl, ClO, and SbCl, respectively. The thermal analysis of the polymers was also investigated. Possible causes for the observed lower conductivity of these polymers have also been discussed. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 91–102, 1999     

Crystallization behavior and crystallite morphology control of poly(L‐lactic acid) through N,N′‐bis(benzoyl)sebacic acid dihydrazide

Adding a nucleating agent is one of the best ways to accelerate the crystallization rate of poly(L ‐lactic acid) (PLLA) so as to obtain a high degree of crystallinity during the process, which will improve the heat distortion temperature of final products. In the work reported, N, N′‐bis(benzoyl)sebacic acid dihydrazide (BSAD) was synthesized and used as a nucleating agent for PLLA. Isothermal and non‐isothermal crystallization behaviors were investigated using differential scanning calorimetry (DSC). The addition of BSAD successfully enhances the crystallization rate of PLLA. A unique phase separation behavior of PLLA/BSAD blends is found from DSC as well as from polarized optical microscopy, which explains the difference of optimal BSAD concentration between isothermal and non‐isothermal crystallization. This is the first recording of a phase separation peak in PLLA/nucleating agent blends using DSC. In thermogravimetric analysis, the enhanced thermal stability indicates that there are strong hydrogen bonds between BSAD and PLLA matrix. BSAD can dissolve in PLLA melt below its melting point through intermolecular hydrogen bonding with PLLA and self‐assemble upon cooling, leading to the surface being capable of nucleating PLLA. Different phase separation temperatures can be used to control the morphology of BSAD, which finally determines the crystallite morphology of PLLA. © 2012 Society of Chemical Industry     

Crystallization kinetics of poly (L‐lactic acid)/montmorillonite nanocomposites under isothermal crystallization condition

Poly(L ‐lactic acid)/o‐MMT nanocomposites, incorporating various amounts of organically modified montmorillonite (o‐MMT; 0–10 wt %), were prepared by solution intercalation. The montmorillonite (MMT) was organically modified with dilauryl dimethyl ammonium bromide (DDAB) by ion exchange. Transmission electron microscopy (TEM) and X‐ray diffraction (XRD) reveal that the o‐MMT was exfoliated in a poly(L ‐lactic acid), (PLLA) matrix. A series of the test specimens were prepared and subjected to isothermal crystallization at various temperatures (T₁–T₅). The DSC plots revealed that the PLLA/o‐MMT nanocomposites that were prepared under nonisothermal conditions exhibited an obvious crystallization peak and recrystallization, but neat PLLA exhibited neither. The PLLA/o‐MMT nanocomposites (2–10 wt %) yielded two endothermic peaks only under isothermal conditions at low temperature (T₁), and the intensity of Tm₂ (the higher melting point) was proportional to the o‐MMT content (at around 171°C). The melting point of the test samples increased with the isothermal crystallization temperature. In the Avrami equation, the constant of the crystallization rate (k) was inversely proportional to the isothermal crystallization temperature and increased with the o‐MMT content, especially at low temperature (T₁). The Avrami exponent (n) of the PLLA/o‐MMT nanocomposites (4–10 wt %) was 2.61–3.56 higher than that of neat PLLA, 2.10–2.56, revealing that crystallization occurred in three dimensions. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Sorption and transport properties of the semi‐interpenetrating network based on crosslinked poly(vinyl alcohol) and poly(styrene sulfonic acid‐co‐maleic anhydride) as proton‐conducting membranes

This study investigates the sorption and transport properties of hydrocarbon membranes based on poly(vinyl alcohol) network and poly(styrene sulfonic acid‐co‐maleic acid) (PSSA‐MA). The water and methanol self‐diffusion coefficients through an 80 wt % PSSA‐MA interpenetrating SIPN‐80 membrane measured 3.75 × 10^?6 and 5.47 × 10^?7 cm²/s, respectively. These results are lower than the corresponding values of Nafion® 115 (8.89 × 10^?6 cm²/s for water and 8.63 × 10^?6 cm²/s for methanol). The methanol permeability of SIPN‐80 membrane is 4.1 × 10^?7 cm²/s, or about one‐fourth that of Nafion® 115. The difference in self‐diffusion behaviors of Nafion® 115 and SIPN‐80 membranes is well correlated with their sorption characteristics. The solvent uptake of Nafion® 115 increased as the methanol concentration increased up to a methanol mole fraction of 0.63, and then decreased. However, the solvent uptake of the SIPN‐80 membranes decreased sluggishly as the methanol concentration increased. The λ values of water and methanol (i.e., λ and λ) in Nafion® 115 are quite close, indicating no sorption preference between water and methanol. In contrast, the λ value is only one‐third λ for a SIPN‐80 membrane. Accordingly, the SIPN membranes are regarded as candidates for direct methanol fuel cell applications. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

A comprehensive single‐particle model for solid‐state polymerization of poly(L‐lactic acid)

We propose here, a comprehensive model for the solid‐state polymerization (SSP) of a low to moderate molecular weight (MW) prepolymer of lactic acid, to produce high MW poly(L ‐lactic acid) (PLLA). The reactions are rationally assumed to occur only in the amorphous region, and effective concentrations of end groups, vary with crystalinity, X_c, during SSP. We estimate byproduct diffusivities, D, using free volume theory. The effects of various parameters on the SSP of PLLA prepolymer have been examined with respect to the optimum MW, X_c and D. We introduce self‐consistently, scaling factors of ～ 0.27, in the experimental procedure, to determine via ¹⁹F‐NMR, concentrations of the end groups, after converting them to fluorinated ester groups. The relevant reaction rate constants are obtained by fitting to early time data from representative SSP experiments at 150°C, under high vacuum, on PLLA prepolymer powder (i.e., spherical geometry) of number average MW, M_n0 ～ 10,200 Da, which attains M_n ～ 150,000 Da, via SSP. The subsequent successful comparison of the model predictions with experimental data throughout the entire SSP duration indicates that the model is comprehensive and accounts for all the relevant phenomena occurring during the SSP to synthesize high MW PLLA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011