The use of acrylated fatty acid methyl esters as styrene replacements in triglyceride‐based thermosetting polymers

Resins containing plant oil‐based cross‐linkers were studied with two reactive diluents: a styrene and an acrylated fatty acid methyl ester‐based (AFAME) monomer. Acrylated epoxidized soybean oil and maleinated castor oil monoglyceride were bio‐based cross‐linkers used. The viscosity and mechanical properties of the resulting polymers were measured and analyzed. Both bio‐based cross‐linkers prepared using the modified AFAME as diluent had a fairly high viscosity, so blends of AFAME and styrene were needed to meet the viscosity requirements established by the composite industry (<1000 cP at room temperature). In addition, the glass transition temperature (T_g) and stiffness of bio‐based cross‐linker/AFAME polymers were significantly lower than the resin/styrene polymers. Ternary blends of maleinated castor oil monoglyceride with AFAME and styrene improved the mechanical properties to acceptable comparable values (storage modulus at 30°C ～ 1200 MPa and T_g ～ 100°C). The addition of 5 wt% of chemically modified lignin led to an improvement in the mechanical properties of the polymeric matrix but caused an increase in the viscosity. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Replacement of styrene with acrylated epoxidized soybean oil in an unsaturated polyester resin from propylene glycol and maleic anhydride

A nonvolatile, vegetable‐oil based chemical, acrylated epoxidized soybean oil (AESO) was investigated as a replacement of volatile and toxic styrene in one of commercial UPE resins styrene‐(PG‐MA) that is a mixture of styrene and a UPE plastic from propylene glycol and maleic anhydride (PG‐MA). Neither AESO nor PG‐MA was capable of forming a strong matrix, respectively, for glass fiber‐reinforced composites. However, a mixture of AESO and PG‐MA resulted in glass fiber‐reinforced AESO‐(PG‐MA) composites that were comparable or even superior to those from styrene‐(PG‐MA) in terms of the flexural and tensile properties. Effects of AESO contents on the mechanical and viscoelastic properties of the glass fiber‐reinforced AESO‐(PG‐MA) composites were investigated. Resin viscosity and resin pot life as a function of temperature were studied. The curing mechanism of the AESO‐(PG‐MA) resins is also discussed. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45056.     

Acrylated epoxidized soybean oil as a styrene replacement in a dicyclopentadiene‐modified unsaturated polyester resin

Nonvolatile and nonhazardous acrylated epoxidized soybean oil (AESO) was investigated as a replacement for hazardous styrene in a commercial unsaturated polyester (UPE) resin [a mixture of styrene and a dicyclopentadiene (DCPD)‐modified UPE (DCPD–UPE)]. DCPD–UPE was prepared from ethylene glycol, diethylene glycol, maleic anhydride, and DCPD. Mixtures of AESO and DCPD–UPE [AESO–(DCPD–UPE) resins] were found to be homogeneous, easily pourable solutions at room temperature. The glass‐fiber‐reinforced composites from the AESO–(DCPD–UPE) resins were comparable or even superior to those from the mixture of styrene and DCPD–UPE in terms of the flexural and tensile strengths. The viscoelastic properties of the cured AESO–(DCPD–UPE) resins and the corresponding glass‐fiber‐reinforced composites were characterized by dynamic mechanical analysis. The viscosities and pot lives of the AESO–(DCPD–UPE) resins as a function of the temperature were studied. The curing mechanism of the AESO–(DCPD–UPE) resins is discussed. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46212.     

Replacement of styrene with acrylated epoxidized soybean oil in an unsaturated polyester resin from propylene glycol,isophthalic acid,and maleic anhydride

Commercial unsaturated polyester (UPE) resins typically contain a high amount of volatile toxic styrene. A non‐volatile acrylated epoxidized soybean oil (AESO) was found to be an excellent replacement of styrene in a commercially available UPE resin [designated as Styrene‐(PG‐IPA‐MA)] that is derived from propylene glycol (PG), isophthalic acid (IPA), and maleic anhydride (MA) in terms of the mechanical properties of the resulting kenaf fiber‐reinforced composites. The AESO‐(PG‐IPA‐MA) resins had low viscosity and long pot life below 70°C for a typical fiber‐reinforced composite application. AESO and PG‐IPA‐MA were not able to form a strong polymer matrix individually for fiber‐reinforced composites. However, a combination of AESO and PG‐IPA‐MA saw strong synergistic effects between them. The flexural, tensile, and water absorption properties of kenaf fiber‐reinforced composites made from AESO‐(PG‐IPA‐MA) resins were comparable with or even superior to those from the Styrene‐(PG‐IPA‐MA) resin. The AESO/(PG‐IPA‐MA) weight ratio was investigated for maximizing the mechanical properties of the kenaf fiber‐reinforced composites. The curing mechanism of the AESO‐(PG‐IPA‐MA) resins is discussed in detail. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43052.     

Soybean‐ and castor‐oil‐based thermosetting polymers: Mechanical properties

Maleic anhydride modified soybean‐ and castor‐oil‐based monomers, prepared via the malination of the alcoholysis products of the oils with various polyols, such as pentaerythritol, glycerol, and bisphenol A propoxylate, were copolymerized with styrene to give hard rigid plastics. These triglyceride‐based polymers exhibited a wide range of properties depending on their chemical structure. They exhibited flexural moduli in the 0.8–2.5 GPa range, flexural strength in the 32–112 MPa range, glass transition temperatures (T_g) ranging from 72 to 152°C, and surface hardness values in the 77–90 D range. The polymers prepared from castor oil exhibited significantly improved modulus, strength, and T_g values when compared with soybean‐oil‐based polymers. These novel castor and soybean‐oil‐based polymers show comparable properties to those of the high‐performance unsaturated polyester (UP) resins and show promise as an alternative to replace these petroleum‐based materials. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1497–1504, 2006     

Photo‐fabricated unsaturated polyester resin composites reinforced by kenaf fibers,synthesis and characterization

New bio‐fiber composites (UPRC) cured by ultraviolet radiation were produced using kenaf fiber as reinforcing agent and unsaturated polyester resins as matrix in the presence of styrene and IRGACURE 1800 as photoinitiator. Unsaturated polyester resins based on palm oil were prepared from various ratios of monoglyceride (MG)/maleic anhydride (MA) by the interaction of the corresponding MG monomer, with different equivalents of MA, in the presence of 2‐methylimidazole as catalyst. The various characteristics of the obtained bio‐fiber composites, including mechanical, gel content, water absorption and thickness swelling test, thermal analysis, were determined and the data were discussed. Bio‐fiber composite with MG: MA ratio (1 : 4 eq./eq.) showed better mechanical properties (tensile, flexural, and impact strength) than other formulations. Gel content increased as the amount of MA was increased up to the MG: MA ratio was 1 : 4 (eq./eq.) then slightly decreased at the higher ratio formulation. Bio‐fiber composite (UPRC_c) was considered the best prepared bio‐fiber composite which contained higher degree double bond, cross‐linking and thermal stability. Moreover, morphological study of selected examples of the formed bio‐fiber composites was also carried out and showed the evidence of the enhancement of the compatibility between fiber and polymer matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polyurethane foams from soyoil‐based polyols

The focus of this work was to synthesize bio‐based polyurethane (PU) foams from soybean oil (SO). Different polyols from SO were produced as follows: soybean oil monoglyceride (SOMG), hydroxylated soybean oil (HSO), and soybean oil methanol polyol (SOMP). The SOMG was a mixture of 90.1% of monoglyceride, 1.3% of diglyceride, and 8.6% of glycerol. The effect of various variables (polyol reactivity, water content curing temperature, type of catalyst, isocyanate, and surfactant) on the foam structure and properties were analyzed. SOMG had the highest reactivity because it was the only polyol‐containing primary hydroxyl (? OH) groups in addition to a secondary ? OH group. PU foams made with SOMG and synthetic polyol contained small uniform cells, whereas the other SO polyols produced foams with a mixture of larger and less uniform cells. The type of isocyanate also had an influence on the morphology, especially on the type of cells produced. The foam structure was found to be affected by the water and catalyst content, which controlled the foam density and the cure rate of the PU polymer. We observed that the glass transition (T_g) increased with the OH value and the type of diisocyanate. Also, we found that the degree of solvent swelling (DS) decreased as T_g increased with crosslink density. These results are consistent with the Twinkling Fractal Theory of T_g. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Rigid,thermosetting liquid molding resins from renewable resources. I. Synthesis and polymerization of soy oil monoglyceride maleates

In this study, rigid thermoset polymers were prepared from radical copolymerization of the soybean oil monoglyceride maleates with styrene. In the first part of the study, soybean oil monoglycerides (SOMGs) were obtained from the reaction of soybean oil with glycerol at 220–240°C with an optimization of the reaction to maximize the monoglyceride yield. In the following step, SOMG were reacted with maleic anhydride at temperatures around 100°C to produce the SOMG maleate half esters. Different catalysts and different reaction conditions were examined to increase the maleate half esters' yields. The reactions were followed by IR and ¹H NMR, and the products were characterized by mass spectrometry. In the final step, the radical initiated copolymerization of the SOMG maleates with styrene produced rigid, thermoset polymers. The emulsion copolymerization of the SOMG maleates with styrene was also carried out successfully without the addition of an emulsifier. The obtained polymers were characterized by IR and the crosslinked network structure of the copolymers was examined with the swelling behavior in different solvents. Mechanical properties of the cured resin such as T_g, dynamic flexural modulus, and surface hardness were also determined. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 69–77, 2001     

Thermal and mechanical properties of acrylated expoxidized‐soybean oil‐based thermosets

A series of epoxidized‐soybean oil (ESO) with different epoxyl content were synthesized by in situ epoxidation of soybean oil (SBO). The acrylated epoxidized‐soybean oil (AESO) was obtained by the reaction of ring opening of ESO using acrylic acid as ring opener. The acrylated expoxidized‐soybean oil‐based thermosets have been synthesized by bulk radical polymerization of these AESOs and styrene. The thermal properties of the resins were characterized by differential scanning calorimetry (DSC) and thermo‐gravimetric analysis (TG). The results showed that these resins possess high thermal stability. There were two glass transition temperature of each resin due to the triglycerides structure of the resins. The tensile strength and impact strength of the resins were also recorded, and the tensile strength and impact strength increased as the iodine value of ESO decreased. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Development of acrylated soybean oil‐based UV‐curable coatings with high impact strength from low viscosity oligomer

In recent years, more and more attention has been paid to bio‐based materials due to their sustainability and environmental friendliness. The combination of biomass and ultraviolet (UV) curing technology can reduce the dependence on petroleum products and emissions of volatile organic compounds. In this article, a new environment‐friendly UV‐curable coating with good performances was successfully prepared from acrylated soybean oil (ACSO). ACSO was obtained at low temperature without catalyst and inhibitor by reacting soybean oil‐based polyol with acryloyl chloride and characterized by Fourier transform infrared spectroscopy and nuclear magnetic resonance. It was found that the UV‐curable oligomer of ACSO had lower viscosity and better ductility, compared to acrylated epoxidized soybean oil (AESO). The properties of UV‐cured films prepared by ACSO were studied and compared with films from AESO. The results showed that the ACSO‐based films were significantly improved in the adhesion and impact resistance. Furthermore, the addition of styrene could enhance the hardness and impact resistance of films. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45698.     

Rigid thermosetting liquid molding resins from renewable resources. II. Copolymers of soybean oil monoglyceride maleates with neopentyl glycol and bisphenol A maleates

Soybean oil monoglycerides (SOMG), obtained by the glycerolysis of soybean oil, were reacted with maleic anhydride to produce SOMG maleate half esters. The copolymers of the SOMG maleates with styrene produced rigid thermosetting polymers. The dynamic mechanical analysis (DMA) of this polymer showed a glass‐transition temperature (T_g) around 133°C and a storage modulus (E′) value around 0.94 GPa at 35°C. The tensile tests performed on this polymer showed a tensile strength of 29.36 MPa and a tensile modulus of 0.84 GPa. Mixtures of SOMG with neopentyl glycol (NPG) and SOMG with bisphenol A (BPA) were also maleinized under the same reaction conditions and the resulting maleates were then copolymerized with styrene. The resulting polymers were analyzed for their mechanical properties. The T_g of the copolymers of the SOMG/NPG maleates with styrene was 145°C and the E′ value at 35°C was 2 GPa. The tensile strength of this polymer as calculated from the stress–strain data was 15.65 MPa and the tensile modulus was 1.49 GPa. The T_g of the copolymers of SOMG/BPA maleates, on the other hand, was found to be around 131°C and the E′ value was 1.34 GPa at 35°C. The changes observed in the mechanical properties of the resulting polymers with the introduction of NPG maleates and BPA maleates to the SOMG maleates can be explained by the structural changes on the polymer backbone. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 972–980, 2002     

Synthesis and characterization of bio‐based thermosetting resins from lactic acid and glycerol

A bio‐based thermoset resin has been synthesized from glycerol reacted with lactic acid oligomers of three different chain lengths (n): 3, 7, and 10. Lactic acid was first reacted with glycerol by direct condensation and the resulting branched molecule was then end‐functionalized with methacrylic anhydride. The resins were characterized by Fourier‐transform infrared spectroscopy (FT‐IR), by ¹³C‐NMR spectroscopy to confirm the chemical structure of the resin, and by differential scanning calorimetry and dynamic mechanical thermal analysis (DMTA) to obtain the thermal properties. The resin flow viscosities were also measured using a rheometer with different stress levels for each temperature used, as this is an important characteristic of resins that are intended to be used as a matrix in composite applications. The resin with a chain length of three had better mechanical, thermal, and rheological properties than the resins with chain lengths of seven and 10. Also, its bio‐based content of 78% and glass transition temperature of 97°C makes this resin comparable to commercial unsaturated polyester resins. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40488.     

New polymers from plant oil derivatives and styrene‐maleic anhydride copolymers

In this study, styrene maleic anhydride copolymer (SMA2000, Styrene : Maleic Anhydride 2 : 1) is grafted and/or crosslinked with epoxidized methyl oleate, epoxidized soybean oil, methyl ricinoleate (MR), castor oil (CO), and soybean oil diglyceride. Base catalyzed epoxy‐anhydride and alcohol‐anhydride polyesters were synthesized by using the anhydride on SMA, the epoxy or secondary alcohol groups on the triglyceride based monomers. The characterizations of the products were done by DMA, TGA, and IR spectroscopy. SMA‐epoxidized soy oil and SMA‐CO polymers are crosslinked rigid infusible polymers. SMA‐epoxidized soy oil and SMA‐CO showed T_g's at 70 and 66°C, respectively. Dynamic moduli of the two polymers were 11.73 and 3.34 Mpa respectively. SMA‐epoxidized methyl oleate, poly[styrene‐co‐(maleic anhydride)]‐graft‐(methyl ricinoleate), and SMA‐soy oil diglyceride polymers were soluble and thermoplastic polymers and were characterized by TGA, GPC, DSC, NMR, and IR spectroscopy. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Morphology and flame‐retardancy properties of ternary high‐impact polystyrene/elastomer/polystyrene‐encapsulated magnesium hydroxide composites

The effects of elastomer type on the morphology, flammability, and mechanical properties of high‐impact polystyrene (HIPS)/polystyrene (PS)‐encapsulated magnesium hydroxide (MH) were investigated. The ternary composites were characterized by cone calorimetry, mechanical testing, and scanning electron microscopy. Morphology was controlled with poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) triblock copolymer or the corresponding maleinated poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS‐g‐MA). The HIPS/SEBS/PS‐encapsulated MH composites exhibited separation of the filler and elastomer, whereas the HIPS/SEBS‐g‐MA/PS‐encapsulated MH composites exhibited encapsulation of the filler by SEBS‐g‐MA. The flame‐retardant and mechanical properties of the ternary composites were strongly dependent on microstructure. The composites with an encapsulation structure showed higher flame‐retardant properties than those with a separation structure at the optimum use level of SEBS‐g‐MA. Furthermore, the composites with a separation structure showed a higher modulus and impact strength than those with an encapsulation structure. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Palm oil‐based unsaturated polyester: Activation energy and swelling properties

In this study, unsaturated polyester (UP) resin based on palm oil was synthesized. Palm oil monoglyceride (POMG) was obtained by alchoholysis process of palm oil at 230°C for 3 h. Then, POMG was treated with maleic anhydride (MA) at different ratio of POMG:MA to produce UP resin. The products were then characterized using Fourier transform infrared (FTIR) spectrometer and proton nuclear magnetic resonance (¹H‐NMR) spectrometer. FTIR and ¹H‐NMR spectrum analyses confirmed that the unsaturated group of MA was chemically attached to POMG. The activation energy of POMG/MA reaction was also studied. The results showed that the ratio of reactants and the presence of 2‐methylimidazole influenced the activation energy of reaction. The prepared UP resin was mixed with 35% of styrene, 0.3% of cobalt naphthenate, and 1% of methyl ethyl ketone peroxide before it was subjected to curing process. The effect of POMG/MG ratio on swelling properties of the cured UP was studied, and the result indicated that toluene and cured UP resin were compatible. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Renewably sourced phenolic resins from lignin bio‐oil

Traditional lignin pyrolysis generates a bio‐oil with a complex mixture of alkyl‐functionalized guaiacol and syringol monomers that have limited utility to completely replace phenol in resins. In this work, formate assisted fast pyrolysis (FAsP) of lignin yielded a bio‐oil consisting of alkylated phenol compounds, due to deoxyhydrogenation, that was used to synthesize phenol/formaldehyde resins. A solvent extraction method was developed to concentrate the phenolics in the extract to yield a phenol rich monomer mixture. Phenolic resins were synthesized using phenol (phenol resin), FAsP bio‐oil (oil resin), and an extract mimic (mimic resin) that was prepared to resemble the extract after further purification. All three phenolic sources could synthesize novolac resins with reactive sites remaining for subsequent resin curing. Differential scanning calorimetry and thermogravimetric analysis of the three resins revealed similar thermal and decomposition behavior of phenol and the mimic resins, while the oil resin was less stable. Resins were cured with hexamethylenetetramine and the mimic resin demonstrated improved curing energies compared to the oil resin. The adhesive strength of the mimic resin was found to be superior to that of the oil resins. These results confirmed that extracting a mixture of substituted aromatics from FAsP bio‐oil could synthesize resins with properties similar to those from phenol and improved over the parent bio‐oil. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44827.     

New sheet molding compound resins from soybean oil. I. Synthesis and characterization

Thermosetting resins were synthesized from soybean oil, which are suited to sheet molding compound (SMC) applications. It was achieved by introducing acid functionality and CC groups onto triglyceride molecules. The acid groups can react with divalent metallic oxides and/or hydroxides to form the sheet, while CC groups undergo free radical polymerization. An acrylated epoxidized soybean oil (AESO), which has an average of 3.4 acrylates per triglyceride, was used as starting material. The hydroxyl groups on AESO reacted with maleic anhydride (MA) to render acid groups on the molecule. The resulting monomer was then copolymerized with 33 wt% styrene to form rigid polymers. Dynamic mechanical analysis showed storage moduli (E′) for these polymers ranging from 1.9 to 2.2 GPa at room temperature, and the glass transition temperatures (T_g) in the range of 100-115 °C. Both the E′ and T_g were increased by increasing the molar ratio of MA to AESO, and the transition from the glassy to the rubbery state was broadened by increasing the amount of MA. The effect of styrene as a comonomer was also examined, and a final formulation for SMC was optimized. The resulting resins exhibited appropriate viscosity during the SMC thickening process.     

Bio‐oil from whole‐tree feedstock in resol‐type phenolic resins

Renewable chemicals are of growing importance in terms of opportunities for environmental concerns over fossil‐based chemicals. Lignocellulosic biomass can be converted into energy and chemicals via thermal and biological processes. Among all the transformation processes available, fast pyrolysis is the only one to produce a high yield of a liquid‐phase product called bio‐oil or pyrolysis oil. Bio‐oil is considered to be a promising substitute for phenol in phenol formaldehyde (PF) resin synthesis. In this work, bio‐based phenolic resins have been formulated, partially substituting phenol by bio‐oils from two Canadian whole‐tree species. The new resins are produced by replacing 25, 50, and 75% of phenol with bio‐oil for each species (three bioresins per species). The aim of this study is to synthesize renewable resins with competitive price and satisfactory quality. The results obtained have shown that substitution degree up to 50% provided reactivity and performance equal or superior to the pure PF resin. They also present a good storage stability, improved shear strength, and thermal stability comparable to the pure PF. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 40014.     

Thermosets resins prepared from soybean oil and lignin derivatives with high biocontent,superior thermal properties,and biodegradability

A bio-based monomer, methacrylated vanillyl alcohol (MVA), had been synthesized from vanillyl alcohol with methacrylate anhydride (MAA) via a solvent-free, efficient method. The synthesis of MVA was confirmed by Fourier transform infrared (FTIR) and proton nuclear magnetic resonance (¹H NMR). It was used to copolymerize with acrylated epoxidized soybean oil (AESO) to prepare a bio-based resin (MVA–AESO). Excess MAA of MVA synthesis was further used to modify AESO with hydroxyl groups, generating (MVA–MAESO) with higher unsaturation degree. Their chemical structure and modification were characterized using ¹³C NMR and Fourier transform infrared analyses. Pure AESO and MVA resins were used to compare with MVA–AESO and MVA–MAESO in terms of their viscosity, curing performance, mechanical, and thermal properties. The synthesized MVA–AESO and MVA–MAESO resins showed much lower viscosities than pure AESO due to the dilution of MVA. In addition, the incorporation of MVA reduced curing temperatures, activation energies which caused MVA–AESO and MVA–MAESO had higher curing degree than pure AESO. With the combination of MVA and modification of MAA, flexible AESO networks exhibited superior flexural properties, storage modulus, glass-transition temperature, and thermal stability. Furthermore, the biodegradation of the formulated bio-based resins were also investigated. Results showed that the addition of monomer and the increase in the content of CC bonds did not significantly affect the biodegradability of AESO, which may be due to the fact that the degradable groups of AESO were not affected. This environmentally friendly, low (volatile organic) resin, prepared by a high efficiency and environmental protection synthetic route, can potentially replace typical petroleum-based thermosets for the production environmentally friendly thermosetting resins. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48827.     

Development of a bio‐based composite material from soybean oil and keratin fibers

A novel bio‐based composite material, suitable for electronic as well as automotive and aeronautical applications, was developed from soybean oils and keratin feather fibers (KF). This environmentally friendly, low‐cost composite can be a substitute for petroleum‐based composite materials. Keratin fibers are a hollow, light, and tough material and are compatible with several soybean (S) resins, such as acrylated epoxidized soybean oil (AESO). The new KFS lightweight composites have a density ρ ≈ 1 g/cm³, when the KF volume fraction is 30%. The hollow keratin fibers were not filled by resin infusion and the composite retained a significant volume of air in the hollow structure of the fibers. Due to the retained air, the dielectric constant, k, of the composite material was in the range of 1.7–2.7, depending on the fiber volume fraction, and these values are significantly lower than the conventional silicon dioxide or epoxy, or polymer dielectric insulators. The coefficient of thermal expansion (CTE) of the 30 wt % composite was 67.4 ppm/°C; this value is low enough for electronic application and similar to the value of silicon materials or polyimides used in printed circuit boards. The water absorption of the AESO polymer was 0.5 wt % at equilibrium and the diffusion coefficient in the KFS composites was dependent on the keratin fiber content. The incorporation of keratin fibers in the soy oil polymer enhanced the mechanical properties such as storage modulus, fracture toughness, and flexural properties, ca. 100% increase at 30 vol %. The fracture energy of a single keratin fiber in the composite was determined to be about 3 kJ/m² with a fracture stress of about 100–200 MPa. Considerable improvements in the KFS composite properties should be possible by optimization of the resin structure and fiber selection. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1524–1538, 2005