Studies in Lithium Oxide Systems: II, Li2O Al2O3–Al2 O 3

Solid-state reactions between Li₂O and Al₂ O₃ were studied in the region between Li₂O.Al₂ O ₃ and Al₂ O ₃. The compound Li₂ O Al₂ O ₃ melts at 1610°± 15°C. and undergoes a rapid reversible inversion between 1200° and 1300°C. Vaporization of Li₂ O from compositions in the system proceeds at an appreciable rate at 1400°C, as shown by fluorescence. Lithium spinel, Li₂ O -5Al₂O₃, was the only other compound observed. The effect of Li₂ O on the sintering of alumina was investigated.     

Studies in Lithium Oxide Systems: XII, Li2O-B2O3-Al2O3

Tentative phase relations in the binary system BnOa-A1₂O₃ are presented as a prerequisite to the understanding of the system Li₂O-B₂O₃-Al₂O₃. Two binary compounds, 2A1₂O₃.B₂O₃ and 9A1₂O₃.-2B₂O₃, melted incongruently at 1030° f 7°C and about 144°C, respectively. Two ternary compounds were isolated, 2Li₂O.A1₂O₃.B₂O₃ and 2Li₂O. 2AI₂O₃. 3B₂0₃. The 2:1:1 compound gave a melting reaction by differential thermal analysis at 870°± 20° C, but the exact nature of the melting behavior was not determined. The 2:2:-3 compound melted at 790°± 20° C to Li_zO.-5Al₂O₃ and liquid. X-ray diffraction data for the compounds are presented and compatibility triangles are shown.     

Studies in Lithium Oxide Systems: V, Li2O-Li20 B2O3

Nine compositions containing 40 to 68% B₂O₃ were used to study the high-lithia portion of the system Li₂O-B₂O₃ by quenching and differential thermal analysis methods. The compounds 3Li₂O 2B₂O₃ and 3Li₂O B₂O₃ melted incongruently at 700°± 6°C, and 715°± 15°C., respectively. The compound 2Li₂O B₂O₃ is assumed to dissociate slightly below 650°± 15° C., although the data could also be interpreted as in-congruent melting. Below 600°± 6°C. it does dissociate to the 3:2 and 3:1 compounds. In this narrow temperature interval the 2:1 compound had an inversion at 618°± 6°C. Both forms of the 2:1 compound could be quenched to room temperature. X-ray diffraction data for the compounds are tabulated, and the complete phase diagram for the system Li₂O-B₂O₃ is presented.     

Studies in Lithium Oxide Systems: VI, Progress Report on the System Li2O-SiO2-TiO2

Data on compatibility triangles and liquid immiscibility are presented for the portion of the ternary system bounded by SiO₂, Li₂O, SiO₂, Li₀O TiO₂, and TiO₂. X-ray data showed the ternary compound Li₂O. TiO₂. SiO₂ to be tetragonal with a = 6.41 a.u. and C = 4.40 a.u. The compound is uniaxial negative with 1.81 < < 1.82 and 1.83 < < 1.84. It melted to two liquids at 1207° 3°C. Seven joins were established by solid-state, fusion, and quenching methods. Using electron microscopy and petrographic microscope and quenching data, liquid immiscibility originating in the binary system SiO₂-TiO₂ was shown to extend over a substantial portion of the ternary system.     

Electrical Conductivity Measurements to Detect Suspected Liquid Phase in the Al2O3-I mol% TiO2-0.5 mol% NaO1/2 and Other Systems

A liquid phase in the Al₂O₃-1 mol% TiO₂-0.5 mol% NaO_1/2 composition is confirmed at ±1300°C by an electrical conductivity measurement. The ease of the method led to a study of the Al₂O₃-2 mol% CuO-2 mol% TiO₂ system and to the geologically important detection of eutectics (peritectics) in rock materials.     

Subsolidus Phase Relationships in the System Fe2O3–Al2O3–TiO2 between 1000° and 1300°C

Subsolidus phase equilibria in the system Fe₂O₃–Al₂O₃–TiO₂ were investigated between 1000° and 1300°C. Quenched samples were examined using powder X-ray diffraction and electron probe microanalytical methods. The main features of the phase relations were: (a) the presence of an M₃O₅ solid solution series between end members Fe₂TiO₅ and Al₂TiO₅, (b) a miscibility gap along the Fe₂O₃–Al₂O₃ binary, (c) an α-M₂O₃( ss ) ternary solid-solution region based on mutual solubility between Fe₂O₃, Al₂O₃, and TiO₂, and (d) an extensive three-phase region characterized by the assemblage M₃O₅+α-M₂O₃( ss ) + Cor( ss ). A comparison of results with previously established phase relations for the Fe₂O₃–Al₂O₃–TiO₂ system shows considerable discrepancy.     

Phase Relations in the System Al2O3–B2O3–Nd2O3

The phase relations at a temperature below "subsolidus" in the system Al₂O₃–B₂O₃–Nd₂O₃ are reported. Specimens were prepared from various compositions of Al₂O₃, B₂O₃, and Nd₂O₃ of purity 99.5%, 99.99%, and 99.9%, respectively, and fired at 1100°C. There are six binary compounds and one ternary compound in this system. The ternary compound, NdAl₃(BO₃)₄ (NAB), has a phase transition at 950°C ± 15°C. The high-temperature form of NAB has a second harmonic generation (SHG) efficiency of KH₂PO₄ (KDP) of the order of magnitude of the form which has been used as a good self-activated laser material, and the low-temperature form of NAB has no SHG efficiency.     

Ionically Conducting Composite Membranes from the Li2O–Al2O3–TiO2–P2O5 Glass–Ceramic

This paper reports processing of lithium ion-conducting, composite membranes comprised of 14Li₂O·9Al₂O₃·38 TiO₂·39P₂O₅ glass–ceramic and polyethylene. The processing involved tape casting of 14Li₂O·9Al₂O₃·38TiO₂·39P₂O₅ glass powder with organic additives into tapes, subjecting the green tape to binder burnout and thermal soaking in the temperature range of 950°–1100°C, and finally infiltrating the porous tape with polyethylene solution. The ionic conductivity and microstructure of 150–350 μm thick membranes were characterized and are discussed in this paper. The crystallites of the glass–ceramic show liquid-like conductivity at ambient temperature, whereas the grain boundary conductivity is lower by a factor of five. The lower grain boundary conductivity is explained on the basis of crystallographic mismatch and the existence of AlPO₄ at the grain boundary. The polyethylene infiltration in the porous membrane improved mechanical resilience with a minor adverse effect on conductivity.     

Formation and Transformation of TiO2 (Anatase) Solid Solution in the System TiO2—Al2O3

In the system TiO₂—Al₂O₃, TiO₂ (anatase, tetragonal) solid solutions crystallize at low temperatures (with up to ∼ 22 mol% Al₂O₃) from amorphous materials prepared by the simultaneous hydrolysis of titanium and aluminum alkoxides. The lattice parameter a is relatively constant regardless of composition, whereas parameter c decreases linearly with increasing Al₂O₃. At higher temperatures, anatase solid solutions transform into TiO₂ (rutile) with the formation of α-Al₂O₃. Powder characterization is studied. Pure anatase crystallizes at 220° to 360°C, and the anatase-to-rutile phase transformation occurs at 770° to 850°C.     

Studies in Germanium Oxide Systems: I, Phase Equilibria in the System Li2O—GeO2

Phase equilibrium relations in the system Li₂O-GeO₂ were determined using standard quenching techniques. In contrast to published literature five congruently melting compounds were found to exist. They are Li₂O·7GeO₂, 3Li₂O O·8GeO₂, Li₂O O·GeO₂, 3Li₂O O·2GeO₂, and 2Li₂O.-GeO₂. The melting points, respectively, are 1033°± 5°C, 953°± 5°C, 1245°± 15°C, 1125°± 15°C, and 1280°± 15°C. Simple binary eutectic relations exist among the compounds. The eutectic temperature between 1:7 and GeO₂ is 1025°± 1h0°C at about 96.8 wt% GeO₂; the eutectic temperature between the 1:7 and 3:8 compounds is 935°± 10°C at about 90.9 wt% GeO₂; the eutectic temperature between the 3:8 and 1:1 compounds is 930°± 10 °C at about 89.8 wt% GeO₂. Liquidus data for compositions richer in lithia than the 1:1 compound are only approximate because of the difficulty of quenching them; the phase relations between the 1:1 and 3:2 and between the 3:2 and 2:l compounds, however, are found to be of the simple binary eutectic type. The glass–forming region was also determined. Melts allowed to cool in air crystallized. When, however, the melts were quenched, glasses containing as much as 8 wt% GeO₂ could be prepared in 5–g quantities. Both the refractive index–composition and density–composition curves for the glasses showed maxi–mums at about 6 to 8 wt% Li₂O.     

Pseudobinary Phase Relations of Li2Ti3O7

The Li₂O-TiO₂ pseudobinary phase diagram was determined from 50 to 100 mol% TiO₂ by DTA, microscopy, and X-ray analysis; Li₂Ti₃O₇ effectively melts congruently at 1300° and decomposes eutectoidally at 940°C. A solid solution based on Li₂TlO₃ from 50 to ∼65 mol% TiO₃ was observed to exist at >930°C. A new metastable phase was discovered with a composition of ∼75 mol% TiO₂ and with a hexagonal unit cell (8.78 by 69.86 × 10⁻¹nm). Discrepancies in the literature regarding some of these phase equilibria are reconciled.     

Uranium Oxide Phase Equilibrium Systems: I, UO2–Al2O3

The UO₂–Al₂O₃ phase equilibrium system was found to contain no new compounds or solid solutions. Uranium dioxide melted at 2878°± 22°C. and Al₂O₃ melted at 2034°± 16°C. The eutectic temperature was approximately 1930°C. There is an indication that two immiscible liquids formed above the eutectic temperature between 53 and 74 mole % Al₂O₃.     

Reactions in the System TiO2-P2O5

The system TiO₂-P₂O₅ was investigated in the compositional range TiO₂.P₂O₅ to 100% TiO₂. Two compounds exist, TiO₂.P₂O₅ and 5TiO₂.-2P₂O₅. TiO₂.P₂O₅ begins to lose P₂O₅ at 1400°C. and both fusion and vaporization proceed rapidly at 1500°C. 5TiO₂.2P₂O₆ melts congruently at 1260°± 3°C. to a glass which can be retained in substantial quantities at room temperature. Physical properties of certain compositions are described.     

Mineralizing Effect of Li2B4O7 and Na2B4O7 on Magnesium Aluminate Spinel Formation

Lithium borate (Li₂B₄O₇) and sodium borate (Na₂B₄O₇) mineralize spinel formation from stoichiometric MgO and Al₂O₃ between 1000° and 1100°C. Mineralization with both compounds is shown to be mediated by B-containing liquids which form glass on cooling. However, the liquid compositions depend on the type of mineralizer and temperature, suggesting that templated grain growth or dissolution–precipitation mechanisms are operating, one dominating over the other under certain conditions. Na₂B₄O₇-mineralized compositions show predominantly templated grain growth at 1000°C, which changes to dissolution–precipitation at 1100°C, whereas Li₂B₄O₇-mineralized compositions show dissolution–precipitation from 1000°C. Li₂B₄O₇ is a stronger mineralizer as spinel formation is complete with 3 wt% Li₂B₄O₇ at 1000°C and with ≥1.5 wt% addition at 1100°C, whereas Na₂B₄O₇-mineralized compositions are found to retain some unreacted corundum even at 1100°C.     

Phase Formation in the System Na2O · Al2O3-CaO · A12O3-Al2O3 at 1200°C in Air

Phase relations in the system Na₂O_· Al₂O₃-CaO· Al₂O₃-Al₂O₃ at 1200°C in air were determined using the quenching method and high-temperature X-ray diffraction. The compound 2Na₂O · 3CaO · 5Al₂O₃, known from the literature, was reformulated as Na₂O · CaO · 2Al₂O₃. A new compound with the probable composition Na₂O · 3CaO · 8Al₂O₃ was found. Cell parameters of both compounds were determined. The compound Na₂O · CaO-2Al₂O₃ is tetragonal with a = 1.04348(24) and c = 0.72539(31) nm; it forms solid solutions with Na₂O · Al₂O₃ up to 38 mol% Na₂O at 1200°C. The compound Na₂O · 3CaO · 8Al₂O₃ is hexagonal with) a = 0.98436(4) and c = 0.69415(4) nm. The compound CaO · 6Al₂O₃ is not initially formed from oxide components at 1200°C but behaves as an equilibrium phase when it is formed separately at higher temperatures. The very slow transformation kinetics between β and β "-Al₂O₃ make it very difficult to determine equilibrium phase relations in the high-Al₂O₃ part of the diagram. Conclusions as to lifetime processes in high-pressure sodium discharge lamps can be drawn from the phase diagram.     

Fabrication and Microstructure Characterization of Continuous Porous TiO2/Al2O3 Composite Membrane

Using a multipass extrusion process, continuous porous Al₂O₃ body (∼41% porosity) was produced and used as a substrate to fabricate continuous porous TiO₂/Al₂O₃ composite membrane. The diameter of the continuous pores of the porous Al₂O₃ body was about 150 μm. The TiO₂ nanopowders dip coated on the continuous pore-surface Al₂O₃ body existed as rutile and anatase phases after calcination at 520°C in air. However, after aging of the fabricated continuous porous TiO₂/Al₂O₃ composite membrane in 20% NaOH at 60°C for 24 h, a large number of TiO₂ fibers frequently observed on the pore surface. The diameter of the TiO₂ fibers was about 150 nm having a high specific surface area. However, after 48-h aging period, the diameter of the TiO₂ fibers increased, which was about 3 μm. Most of the TiO₂ fibers had polycrystalline structure having nanosized rutile and anatase crystals of about 20 nm.     

Phase Relations in the System Li2O.B2O3-B2O3-NiO

Phase equilibria were determined by standard quench methods in binary systems NIO-B₂O₃, the binary join Li₂O.B₂O₃-NiO, and three other sections through the Li₂O.B₂O₃-B₂O₃-NiO system. The only new compound observed was 2NiO.B₂O₃, which is stable from 1303° to 1480°C.     

The Al2O3-Nd2O3 Phase Diagram

A tentative phase diagram for the system Al₂0₃-Nd₂O₃ is presented. Three compounds were obtained: a β -A1₂O₃-type compound, the perovskite NdAlO₃, and Nd₄Al₂O₉. The perovskite melts congruently (mp 2090°C), and the two other compounds exhibit incongruent melting behavior: β -Nd/Al₂O₃, mp 1900°C; Nd₄Al₂O₉, mp 1905°C. Two eutectics exist with the following compositions and melting points: 80 mol% Al₂O₃, 1750°C; 23 mol% Al₂O₃,1800°C. Nd₄Al₂O9 decomposes in the solid state at 1780°C.     

The System CaO-Al2O3-H2O

Phase equilibria have been determined in the system CaO-Al₂O₃-H₂O in the temperature range 100° to 1000°C. under water pressures of up to 3000 atmospheres. Only three hydrated phases are formed stably in the system: Ca(OH)₂, 3CaO·Al₂O₃·6H₂O, and 4CaO·3Al₂O₃-3H₂O. Pressure-temperature curves delineating the equilibrium decomposition of each of these phases have been determined, and some ther-mochemical data have been deduced therefrom. It has been established that both the compounds CaO·Al₂O₃ and 3CaO·Al₂O₃ have a minimum temperature of stability which is above 1000°C. The relevance of the new data to some aspects of cement chemistry is discussed.     

Preparation and Sintering of Monosized Al2O3-TiO2 Composite Powder

An unagglomerated, monosized Al₂O₃TiO₂ composite powder was prepared by the stepwise hydrolysis of titanium alkoxide in an Al₂O₃ dispersion. Particle size was controlled by selecting the particle size of the starting Al₂O₃ powder; TiO₂ content was determined by the amount of alkoxide hydrolyzed. A composite-powder compact containing 50 mol% TiO₂, when fired at 1350°C for 30 min, showed nearly theoretical density with aluminum titanate phase formation.