Effect of poly(epichlorohydrin) on the thermal and mechanical properties of poly(vinyl chloride)

Five kinds of polyepichlorohydrin (PECH) of different molecular weights were synthesized and characterized by gel permeation chromatography (GPC). Mechanical blending was used to mix PECH and poly(vinyl chloride) (PVC) together. The blends of different PVC/PECH ratios were characterized by thermogravimetric analysis (TGA), tensile tests, differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). TGA results show the thermal stability of PVC/PECH blends is desirable. Tensile tests indicate elongation at break is raised by increasing both the amount and the molecular weight of PECH. DSC is used to determine the glass transition temperature of PECH, and a quite low T_g is obtained. DMA results indicate that PECH has a perfect compatibility with PVC, when PECH concentration is below 20 wt %. There is only one peak in each tan δ curve, and the corresponding T_g decreases as PECH amount increases. However, above 20 wt %, phase separation takes place. The molecular weight of PECH also has a great influence on the glass transition temperature of the blends. This study shows that PECH is an excellent plasticizer for PVC, and one can tailor the glass transition temperature and tensile properties by changing the amount and the molecular weight of PECH. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Molecular aggregation in poly(vinyl chloride)

Molecular weight distributions and molecular aggregation for poly(vinyl chloride) (PVC) polymerized in bulk at ?10, ?30, and ?50°C have been measured using gel permeation chromatography. The aggregate content in PVC polymerized at ?50°C was found to be 87 wt-%. These spherical aggregates of mean diameter of 5000 A are formed preferentially from PVC chains having high molecular weights and long syndiotactic sequence lengths. A temperature of 200°C was used to disintegrate these aggregates into single PVC molecules. In disagreement with measurements of M _n and M _w published in the literature, our measured values do not reach a minimum but rather increase continuously with decreasing temperature of polymerization. This disagreement is most probably due to the phenomenon of molecular aggregation in PVC.     

Melt viscosity of poly(vinyl chloride) formulations

Commercial, suspension-type PVC resin, poly (vinyl chloride), molecular weight M_w × 10^?4 = 8.6 ± 0.9, polydispersity M_w/M_n = 2.26, was mixed with plasticizer di(2-ethyl hexyl)phthalate (DOP) and organo-tin stabilizer in four different proportions. The mixtures were milled and pressed into sheets for testing. The polymer content in these samples was 97, 80, 60, and 40 wt percent. The viscoelastic properties of the materials were investigated using a Weissenberg rheogoniometer in a cone-and-plate, steady-state shearing mode. The viscosities and primary normal stress difference coefficients were measured at shear rates of 10^?2 ≤ \documentclass{article}\pagestyle{empty}\begin{document}$ \mathop \gamma \limits^. $\end{document} (sec^?1) ≤ 10² and at temperatures from 151 to 246°C. The zero shear viscosities, plotted as log η₀ vs 1/T (T is the absolute temperature) did not follow either a straight line dependence, reported for PVC melts at low shear rates at 170–190°C, nor was any discontinuity found near 195°C as by others; the data follows a continuous concave curve. The apparent activation energy of flow increases steeply with decreasing temperature. The data can be represented by a WLF type of equation, but the magnitudes of the parameters of this relation differ from expected values. A crossplot of log η₀ (T = const.) vs log w (where w is the polymer content) also demonstrates a faster increase of η₀ with w than expected from the straight line dependence. The primary normal stress difference coefficient was found to increase with w and decrease with T, paralleling the observed dependencies of η₀.     

Structure and properties of polyamide 6 blends with low‐density polyethylene grafted by itaconic acid and with neutralized carboxyl groups

A comparative study of the structure and properties of two‐phase blends of polyamide 6 (PA6) and low‐density polyethylene (LDPE) modified in the course of reactive extrusion, by grafting of itaconic acid (IA) without neutralization of carboxyl groups (LDPE‐g‐IA) and with neutralized carboxyl groups (LDPE‐g‐IA^?M⁺) was carried out. It was shown that 30 wt % of LDPE‐g‐IA^?M⁺ introduced to PA6 resulted in blends of higher Charpy impact strength compared with that of PA6/LDPE‐g‐IA blends. The maximum increase was achieved when Mg(OH)₂ was used as a neutralizing agent. The blend morphology has a two‐phase structure with blurred interphases because of increased adhesion between the phases. The neutralization of carboxyl groups in grafted IA did not lead to two‐phase morphology of blends, which had a negative influence on the mechanical properties. It is believed that the differences in the impact strength were caused by the influence of the added neutralizing agents on the structure of interphases, which depends on both the interfaces adhesion and structural effects resulting from the nucleating behavior of the neutralizing agent. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1702–1708, 2004     

Synthesis and characterization of ternary‐copolymer of soluble fluorinated polyimides based on 1,4‐bis (4‐amino‐2‐trifluoromethylphenoxy) benzene

A series of novel ternary‐copolymer of fluorinated polyimides (PIs) were prepared from 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene (pBATB), commercially available aromatic dianhydrides, and aromatic diamines via a conventional two‐step thermal or chemical imidization method. The structures of all the obtained PIs were characterized with FTIR, ¹H‐NMR, and element analysis. Besides, the solubility, thermal stability, mechanical properties, and moisture uptakes of the PIs were investigated. The weight‐average molecular weight (M_w) and the number‐average molecular weight (M_n) of the PIs were determined using gel‐permeation chromatography (GPC). The PIs were readily dissolved not only in polar solvents such as DMF, DMAc, and NMP, but also in some common organic solvents, such as acetic ester, chloroform, and acetone. The glass transition temperatures of these PIs ranged from 201 to 234°C and the 10% weight loss temperatures ranged from 507 to 541°C in nitrogen. Meanwhile, all the PIs left around 50% residual even at 800°C in nitrogen. The GPC results indicated that the PIs possessed moderate‐to‐high number‐average molecular weight (M_n), ranging from 9609 to 17,628. Moreover, the polymer films exhibited good mechanical properties, with elongations at break of 8–21%, tensile strength of 66.5–89.8 MPa, and Young's modulus of 1.04–1.27 GPa, and low moisture uptakes of 0.54–1.13%. These excellent combination properties ensure that the polymer could be considered as potential candidates for photoelectric and microelectronic applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Structural changes of PVC in PVC/LDPE melt‐blends: Effects of LDPE content and number of extrusions

This paper investigates the structural changes of polyvinyl chloride (PVC) in melt‐blends of a low‐density polyethylene (LDPE) and polyvinyl chloride (PVC), and the effects of LDPE content and number of extrusion passes. These effects were examined in terms of changes in weight average molecular weight and number average molecular weight, polyene and carbonyl indices, color changes of the blend, and the variations in glass transition and decomposition temperatures. It was found that loading LDPE into PVC led to the formation of short‐chain LDPE grafted PVC (s‐LDPE‐g‐PVC) copolymers, via a macro‐radical cross‐recombination reaction, which had greater weight average molecular weight with unchanged number average molecular weight, increased decomposition temperature, lower glass transition temperature, as compared to the pure PVC sample. The dehydrochlorination reaction of PVC was suppressed by the macro‐radical cross‐recombination reaction with addition of LDPE, the effect being more pronounced at 13.0 wt% LDPE. For a given LDPE content, the macro‐radical cross‐recombination and dehydrochlorination reactions competed with one another, thus causing the increases in molecular weight average and molecular weight number up to the 4th extrusion pass. At the 5th extrusion pass, the dehydrochlorination reaction was predominant owing to a depletion of LDPE content to be grafted onto PVC molecular chains. The glass transition and decomposition temperature decreased with increasing number of extrusion passes. Polym. Eng. Sci. 44:487–495, 2004. © 2004 Society of Plastics Engineers.     

Stereocomplex formation between poly(L‐lactic acid) and poly(D‐lactic acid) with disproportionately low and high molecular weights from the melt

Poly(L ‐lactic acid) (PLLA) and poly(D ‐lactic acid) (PDLA) with very different weight‐average molecular weights (M_w) of 4.0 × 10³ and 7.0 × 10⁵ g mol^?1 (M_w(PDLA)/M_w(PLLA) = 175) were blended at different PDLA weight ratios (X_D = PDLA weight/blend weight) and their crystallization from the melt was investigated. The presence of low molecular weight PLLA facilitated the stereocomplexation and thereby lowered the cold crystallization temperature (T_cc) for non‐isothermal crystallization during heating and elevated the radial growth rate of spherulites (G) for isothermal crystallization, irrespective of X_D. The orientation of lamellae in the spherulites was higher for the neat PLLA, PDLA and an equimolar blend than for the non‐equimolar blends. It was found that the orientation of lamellae in the blends was maintained by the stereocomplex (SC) crystallites. Although the G values are expected to decrease with an increase in X_D or the content of high‐molecular‐weight PDLA with lower chain mobility compared with that of low‐molecular‐weight PLLA, G was highest at X_D = 0.5 where the maximum amount of SC crystallites was formed and the G values were very similar for X_D = 0.4 and X_D = 0.6 with the same enantiomeric excess. This means that the effect of SC crystallites overwhelmed that of chain mobility. The nucleating mechanisms of SC crystallites were identical for X_D = 0.1–0.5 in the T_c range 130–180 °C. Copyright © 2011 Society of Chemical Industry     

Synthesis and biological activity of medium range molecular weight polymers containing exo‐3,6‐epoxy‐1,2,3,6‐tetrahydrophthalimidocaproic acid

A new monomer, exo‐3,6‐epoxy‐1,2,3,6‐tetrahydrophthalimidocaproic acid (ETCA), was prepared by reaction of maleimidocaproic acid and furan. The homopolymer of ETCA and its copolymers with acrylic acid (AA) or with vinyl acetate (VAc) were obtained by photopolymerizations using 2,2‐dimethoxy‐2‐phenylacetophenone as an initiator at 25 °C. The synthesized ETCA and its polymers were identified by FTIR, ¹H NMR and ¹³C NMR spectroscopies. The apparent average molecular weights and polydispersity indices determined by gel permeation chromatography (GPC) were as follows: M_n = 9600 g mol^?1, M_w = 9800 g mol^?1, M_w/M_n = 1.1 for poly(ETCA); M_n = 14 300 g mol^?1, M_w = 16 200 g mol^?1, M_w/M_n = 1.2 for poly(ETCA‐co‐AA); M_n = 17 900 g mol^?1, M_w = 18 300 g mol^?1, M_w/M_n = 1.1 for poly(ETCA‐co‐VAc). The in vitro cytotoxicity of the synthesized compounds against mouse mammary carcinoma and human histiocytic lymphoma cancer cell lines decreased in the following order: 5‐fluorouracil (5‐FU) ≥ ETCA > polymers. The in vivo antitumour activity of the polymers against Balb/C mice bearing sarcoma 180 tumour cells was greater than that of 5‐FU at all doses tested. © 2001 Society of Chemical Industry     

Preparation and characterization of poly(vinyl chloride)/polystyrene/poly(ethylene glycol) hollow‐fiber ultrafiltration membranes

Hollow‐fiber ultrafiltration (UF) membranes were prepared from blends of poly(vinyl chloride) (PVC) and polystyrene (PS) with a dry/wet phase inversion method. Poly(ethylene glycol) (PEG) and N,N‐dimethylacetamide were used as the additive and solvent, respectively. The effects of the PEG concentration in the dope solution as an additive on the cross sections and inner and outer surface morphologies, permeability, and separation performance of the hollow fibers were examined. The mean pore size, pore size distribution, and mean roughness of both the inner and outer surfaces of the produced hollow fibers were determined by atomic force microscopy. Also, the mechanical properties of the hollow‐fiber membranes were investigated. UF experiments were conducted with aqueous solutions of poly(vinyl pyrrolidone) (PVP; K‐90, M_w = 360 kDa). From the results, we found that the PVC/PS hollow‐fiber membranes had two layers with a fingerlike structure. These two layers were changed from a wide and long to a thin and short morphology with increasing PEG concentration. A novel and until now undescribed shape of the nodules in the outer surfaces, which was denoted as a sea‐waves shape, was observed. The outer and inner pore sizes both increased with increasing PEG concentration. The water permeation flux of the hollow fibers increased from 104 to 367 L m^?2 h^?1 bar^?1) at higher PEG concentrations. The PVP rejection reached the highest value at a PEG concentration of 4 wt %, whereas at higher values (from 4 to 9 wt %), the rejection decreased. The same trend was found also for the tensile stress at break, Young's modulus, and elongation at break of the hollow fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 989‐1004, 2013     

Mechanical,morphological, and thermal properties of poly(vinyl chloride)/low‐density polyethylene composites filled with date palm leaf fiber

This article investigates the mechanical, morphological, and thermal properties of poly(vinyl chloride) (PVC) and low‐density polyethylene (LDPE) blends, at three different concentrations: 20, 50, and 80 wt% of LDPE. Besides, composite samples that were prepared from PVC/LDPE blend reinforced with different date palm leaf fiber (DPLF) content, 10, 20, and 30 wt%, were also studied. The sample in which PVC/LDPE (20 wt%/80 wt%) had the greatest tensile strength, elongation at break, and modulus. The good thermal stability of this sample can be seen that T_10% and T_20% occurred at higher temperatures compared to others blends. DPLF slightly improved the tensile strength of the polymer blend matrix at 10 wt% (C10). The modulus of the composites increased significantly with increasing filler content. Ageing conditions at 80°C for 168 h slightly improved the mechanical properties of composites. Scanning electron microscopic micrographs showed that morphological properties of tensile fracture surface are in accordance with the tensile properties of these blends and composites. Thermogravimetric analysis and derivative thermogravimetry show that the thermal degradation of PVC/LDPE (20 wt%/80 wt%) blend and PVC/LDPE/DPLF (10 and 30 wt%) composites took place in two steps: in the first step, the blend was more stable than the composites. In the second step, the composites showed a slightly better stability than the PVC/LDPE (20 wt%/80 wt%) blend. Based on the above investigation, these new green composites (PVC/LDPE/DPLF) can be used in several applications. J. VINYL ADDIT. TECHNOL., 25:E88–E93, 2019. © 2018 Society of Plastics Engineers     

Synthesis and characterization of poly(butylene terephthalate)‐co‐poly(butylene succinate)‐block‐poly(ethylene glycol) segmented block copolymers

Poly(butylene terephthalate)‐co‐poly(butylene succinate)‐block‐poly(ethylene glycol) segmented random copolymers, with poly(butylene succinate) (PBS) molar fraction (M_PBS) varying from 10 to 60 %, were synthesized through a melt polycondensation process and characterized by means of GPC, NMR, DSC and mechanical testing. The number‐average relative molecular mass of the copolymers was higher than 4 × 10⁴ g mol^?1 with polydispersity below 1.9. Sequence distribution analysis on the two types of hard segments by means of ¹H NMR revealed that the number‐average sequence length of PBT decreased from 2.80 to 1.23, while that of PBS increased from 1.27 to 4.76 with increasing M_PBS. The random distribution of hard segments was also justified because of the degree of randomness around 1.0. Micro‐phase separation structure was verified for the appearance of two glass transition temperatures and two melting points, respectively, in DSC thermograms of most samples. The crystallinity of hard segments changed with the crystallizability controlled by the average sequence length and reached the minimum value at an M_PBS of about 50–60 mol%. The results can also be ascribed to the co‐crystallization between two structurally analogous hard segments. Mechanical testing results demonstrated that incorporating a certain amount of PBS moieties (less than 30 mol%), at the expense of a minute depression of the elastic modulus, that higher relative elongation and more flexibility of polymer chain could be expected. Maximum equilibrium water absorption and faster degradation rates were observed on samples with higher M_PBS values and lower crystallinity of hard segments were better hydrophilicity of the polymer chain, through in vitro degradation experiments. Copyright © 2003 Society of Chemical Industry     

Characterization of poly(vinyl pyrrolidone‐co‐isobutylstyryl polyhedral oligomeric silsesquioxane) nanocomposites

Poly(vinyl pyrrolidone‐co‐isobutyl styryl polyhedral oligomeric silsesquioxane)s (PVP–POSS) were synthesized by one‐step polymerization and characterized using FTIR, high‐resolution ¹H‐NMR, solid‐state ¹³C‐NMR, ²⁹Si‐NMR, GPC, and DSC. The POSS content can be controlled by varying the POSS feed ratio. The T_g of the PVP–POSS hybrid is influenced by three main factors: (1) a diluent role of the POSS in reducing the self‐association of the PVP; (2) a strong interaction between the POSS siloxane and the PVP carbonyl, and (3) physical aggregation of nanosized POSS. At a relatively low POSS content, the role as diluent dominates, resulting in a decrease in T_g. At a relatively high POSS content, the last two factors dominate and result in T_g increase of the PVP–POSS hybrid. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2208–2215, 2004     

Effect of the compatibility on dielectric performance and breakdown strength of poly(vinylidene fluoride)/low‐density polyethylene blends

Immiscible polymer blends with high dielectric constant (ε) and improved breakdown strength (E_b) performance were obtained by composing poly(vinylidene fluoride) (PVDF) with low‐density polyethylene (LDPE) or the LDPE grafted with maleic anhydride (LDPE‐g‐MAH) through melt‐blending way. The dielectric properties of these blends were emphasized for considering the compatibility effect on the energy storage application. Interface morphology, co‐continuity behavior, and grafted ratio were simultaneously investigated to detect the compatibility enhancement after introducing MAH. Results showed that the MAH positively improved the dielectric properties. Both the measured E_b of PVDF/LDPE and PVDF/LDPE‐g‐MAH blends showed a minimum value at v^PVDF = 50 vol % because of the worst compatibility; meanwhile, higher E_b of PVDF/LDPE‐g‐MAH than that of PVDF/LDPE blend was observed owing to the better compatibility. For considering the effect interface morphology on the dielectric performance, layer‐structure films composing with pure PVDF and LDPE layers were further constructed and studied. It was revealed that the layered structure could be treated as a helpful way to improve ε and E_b for immiscible polymer blends. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42507.     

Synthesis of poly(D,L‐lactic acid) modified by triethanolamine by direct melt copolycondensation and its characterization

Using D ,L ‐lactic acid (LA) and multifunctional group compound triethanolamine (TEA) as starting materials, a novel biodegradable material poly(D ,L ‐lactic acid‐triethanolamine) [P(LA‐TEA)] was directly synthesized by simpler and practical melt polycondensation. The appropriate synthetic condition was discussed in detail. When the molar feed ratio LA/TEA was 30/1, the optimal synthesis conditions were as follows: a prepolymerization time of 12 h; 0.5 weight percent (wt %) SnO catalyst; and melt copolycondensation for 8 h at 160°C, which gave a novel star‐shaped poly(D,L ‐lactic acid) (PDLLA) modified by TEA with the maximum intrinsic viscosity [η] 0.93 dL g⁻¹. The copolymer P(LA‐TEA) as a different molar feed ratio was characterized by [η], Fourier transform infrared spectroscopy (FTIR), proton nuclear magnetic resonance (¹H‐NMR), gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and X‐ray diffraction (XRD). Increasing the molar feed ratio of LA/TEA, T_g and M_w increased. However, all copolymers were amorphous, and their T_g (12.2°C–32.5°C) were lower than that of homopolymer PDLLA. The biggest M_w was 9400 Da, which made the biodegradable polymer be potentially used as drug delivery carrier, tissue engineering material, and green finishing agent in textile industry. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Nitroxide‐mediated synthesis of styrenic‐based segmented and tapered block copolymers using poly(lactide)‐functionalized TEMPO macromediators

Poly(styrene)‐poly(lactide) (PS‐PLA), poly (tert‐butyl styrene)‐poly(lactide) (PtBuS‐PLA) diblocks, and poly(tert‐butyl styrene)‐poly(styrene)‐poly(lactide) (PtBuS‐PS‐PLA) segmented and tapered triblocks of controlled segment lengths were synthesized using nitroxide‐mediated controlled radical polymerization. Well‐defined PLA‐functionalized macromediators derived from hydroxyl terminated TEMPO (PLA_T) of various molecular weights mediated polymerizations of the styrenic monomers in bulk and in dimethylformamide (DMF) solution at 120–130°C. PS‐PLA and PtBuS‐PLA diblocks were characterized by narrow molecular weight distributions (polydispersity index (M_w/M_n) < 1.3) when using the PLA_T mediator with the lowest number average molecular weight M_n= 6.1 kg/mol while broader molecular weight distributions were exhibited (M_w/M_n = 1.47‐1.65) when using higher molecular weight mediators (M_n = 7.4 kg/mol and 11.3 kg/mol). Segmented PtBuS‐PS‐PLA triblocks were initiated cleanly from PtBuS‐PLA diblocks although polymerizations were very rapid with PS segments ～ 5–10 kg/mol added within 3–10 min of polymerization at 130°C in 50 wt % DMF solution. Tapering from the PtBuS to the PS segment in semibatch mode at a lower temperature of 120°C and in 50 wt % DMF solution was effective in incorporating a short random segment of PtBuS‐ran‐PS while maintaining a relatively narrow monomodal molecular weight distribution (M_w/M_n ≈ 1.5). © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Bulk polymerization of vinyl chloride with half-titanocene/MAO catalyst

Bulk polymerization of vinyl chloride (VC) with Cp^∗Ti(OPh)₃/MAO catalyst was investigated. The bulk polymerization of VC with Cp^∗Ti(OPh)₃/MAO catalyst proceeded to give poly(vinyl chloride) (PVC) with high molecular weight in good yields. The M_n of the polymer increased in direct proportion to polymer yields and the line passed through the origin. The M_w/M_n of the polymer decreased with an increase of polymer yield. The GPC elution curves were unimodal and the whole curves shifted clearly to the higher molecular weight as a function of reaction time. This indicates that the control of molecular weight can be achieved in the polymerization of VC with Cp^∗Ti(OPh)₃/MAO catalyst even in bulk. The structure of PVC obtained from the bulk polymerization of VC with Cp^∗Ti(OPh)₃/MAO catalyst consists of a regular structure. The thermal stability of the polymer obtained with Cp^∗Ti(OPh)/MAO catalyst was higher than that of PVC obtained from radical polymerization and depended on the molecular weight of the polymer. In contrast to that, the initial decomposition temperature of the polymer obtained from a radical polymerization did not depend on the molecular weight. We presumed that the decomposition of the polymer obtained with Cp^∗Ti(OPh)₃/MAO catalyst initiated at the chain end.     

Porous biodegradable polyesters. I. Preparation of porous poly(L‐lactide) films by extraction of poly(ethylene oxide) from their blends

Porous poly(L ‐lactide) (PLLA) films were prepared by water extraction of poly(ethylene oxide) (PEO) from solution‐cast PLLA and PEO blend films. The dependence of blend ratio and molecular weight of PEO on the porosity and pore size of films was investigated by gravimetry and scanning electron microscopy. The film porosity and extracted weight ratio were in good agreement with the expected for porous films prepared using PEO of low molecular weight (M_w = 1 × 10³), but shifted to lower values than expected when high molecular weight PEO (M_w = 1 × 10⁵) was utilized. The maximum pore size was larger for porous films prepared from PEO having higher molecular weight, when compared at the same blending ratio of PLLA and PEO before water extraction. Differential scanning calorimetry of as‐cast PLLA and PEO blend films revealed that PLLA and PEO were phase‐separated at least after solvent evaporation. On the other hand, comparison of blend films before and after extraction suggested that a small amount of PEO was trapped in the amorphous region between PLLA crystallites even after water extraction and hindered PLLA crystallization during solvent evaporation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 629–637, 2000     

Synthesis of poly(octadecyl acrylate‐b‐styrene‐b‐octadecyl acrylate) triblock copolymer by atom transfer radical polymerization

The synthesis of triblock copolymer poly(octadecyl acrylate‐b‐styrene‐b‐octadecyl acrylate), using atom transfer radical polymerization (ATRP), is reported. The copolymers were prepared in two steps. First, polystyrene was synthesized by ATRP using α,α′‐dichloro‐p‐xylene/CuBr/bpy as the initiating system; Second, polystyrene was further used as macroinitiator for the ATRP of octadecyl acrylate to prepare ABA triblock copolymers in the presence of FeCl₂·4H₂O/PPh₃ in toluene. Polymers with controlled molecular weight (M_n = 17,000–23,400) and low polydispersity index value (1.33–1.44) were obtained. The relationship between molecular weight versus conversion showed a straight line. The effect of reaction temperature on polymerization was also investigated, showing a faster polymerization rate under higher temperature. The copolymers were characterized by FTIR, ¹H‐NMR, DSC, and GPC and the crystallization behavior of the copolymers was also studied. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1539–1545, 2004     

Metal‐solvating and self‐association of amphiphilic polyamides containing poly(oxyethylene) blocks

An amphiphilic poly(ether amide) consisting of hydrophilic poly(oxyethylene) amide blocks was prepared from the copolymerization of sebacic acid and two poly(oxyalkylene) diamines including a poly(oxyethylene) diamine (POE‐amine at 2000 M_w) and a poly(oxypropylene) diamine (POP‐amine at 230 M_w). The copolymer was estimated to have an average molecular weight of 15,000 M_w (GPC) or approximately three hydrophilic POE segments per strain. The presence of POE segments rendered polymer hydrophilicity and complexing ability for Li⁺, K⁺, Ca⁺², Ni⁺², Pd⁺², and Cu⁺² salts. In particular, lithium perchlorate affected the copolymer to the greatest extent in enhancing electrostatic dissipation or reducing surface resistivity as low as 10^5.0 Ω/sq (cross‐sectional area) at 1/180 Li⁺/EO from 10^7.2 Ω/sq (without metal ion). In such a metal complexation, the copolymer showed a new POE segmental crystalline phase at a melting temperature between ?10.4 and ?14°C, accompanied with the metal‐free original phase of ?31°C. In static toluene/water, the metal ions had no effect on the copolymer surfactancy in lowering the interfacial tension, reaching 4.4 dyn/cm at a critical micelle concentration (cmc) of 0.01 wt %. When mixing toluene and water, the lithium or nickel ions were found to be detrimental to the emulsifying process. Without the metal ion, fine droplets at average sizes of 4.5–5.0 μm were observed in the copolymer/ toluene/water emulsification. These amphiphilic behaviors of the POE‐segmented polyamide with or without metal ions were explained by the competing noncovalent bonding interactions among POE/metal ion/water. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 612–621, 2002     

Synthesis of 1,3‐benzodioxole end‐functionalized polymers via reversible addition–fragmentation chain transfer polymerization

Reversible addition–fragmentation chain transfer (RAFT) polymerization of styrene was carried out in the presence of a novel RAFT reagent, bearing 1,3‐benzodioxole group, benzo [1,3]dioxole‐5‐carbodithioic acid benzo [1,3]dioxol‐5‐ylmethyl ester (BDCB), to prepare end‐functionalized polystyrene. The polymerization results showed that RAFT polymerization of styrene could be well controlled. Number–average molecular weight (M_n(GPC)) increased linearly with monomer conversion, and molecular weight distributions were narrow (M_w/M_n < 1.4). The successful reaction of chain extension and analysis of ¹H NMR spectra confirmed the existence of the functional 1,3‐benzodioxole group at the chain‐end of polystyrene. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3535–3539, 2006