Adiabatic burning velocity of H2–O2 mixtures diluted with CO2/N2/Ar

Global warming due to CO₂ emissions has led to the projection of hydrogen as an important fuel for future. A lot of research has been going on to design combustion appliances for hydrogen as fuel. This has necessitated fundamental research on combustion characteristics of hydrogen fuel. In this work, a combination of experiments and computational simulations was employed to study the effects of diluents (CO₂, N₂, and Ar) on the laminar burning velocity of premixed hydrogen/oxygen flames using the heat flux method. The experiments were conducted to measure laminar burning velocity for a range of equivalence ratios at atmospheric pressure and temperature (300 K) with reactant mixtures containing varying concentrations of CO₂, N₂, and Ar as diluents. Measured burning velocities were compared with computed results obtained from one-dimensional laminar premixed flame code PREMIX with detailed chemical kinetics and good agreement was obtained. The effectiveness of diluents in reduction of laminar burning velocity for a given diluent concentration is in the increasing order of argon, nitrogen, carbon dioxide. This may be due to increased capabilities either to quench the reaction zone by increased specific heat or due to reduced transport rates. The lean and stoichiometric H₂/O₂/CO₂ flames with 65% CO₂ dilution exhibited cellular flame structures. Detailed three-dimensional simulation was performed to understand lean H₂/O₂/CO₂ cellular flame structure and cell count from computed flame matched well with the experimental cellular flame.     

O2/CO2和O2/N2氛围下煤粉富氧燃烧数值模拟

在目前煤炭依然作为能源主体的背景下，控制燃煤污染物排放有着重要意义。基于CFD数值模拟，建立伴流燃烧器模型，控制燃料、氧化剂入口流量恒定，设计了O₂/CO₂、O₂/N₂氧化剂氛围中O₂浓度在21%～40%内的多种工况，对煤粉燃烧特性及燃烧产生的污染物进行了研究。分析了不同工况下煤粉燃烧的温度分布、燃烧速率、碳烟、NO_x的生成情况。结果显示，在O₂/CO₂、O₂/N₂两种氧化剂氛围中，随着O₂浓度的上升，煤粉燃烧温度升高、燃烧速率增大，碳烟生成量均增加，同等O2浓度条件下，O₂/CO₂氛围的煤粉燃烧温度和燃烧速率均高于O₂/N₂氛围，碳烟生成量小于O₂/N₂氛围，且O₂/CO₂...     

Oxidative steam reforming of ethanol over Ni/Al2O3 catalysts promoted by CeO2, ZrO2 and CeO2–ZrO2

Oxidative steam reforming of ethanol at low oxygen to ethanol ratios was investigated over nickel catalysts on Al₂O₃ supports that were either unpromoted or promoted with CeO₂, ZrO₂ and CeO₂–ZrO₂. The promoted catalysts showed greater activity and a higher hydrogen yield than the unpromoted catalyst. The characterization of the Ni-based catalysts promoted with CeO₂ and/or ZrO₂ showed that the variations induced in the Al₂O₃ by the addition of CeO₂ and/or ZrO₂ alter the catalyst's properties by enhancing Ni dispersion and reducing Ni particle size. The promoters, especially CeO₂–ZrO₂, improved catalytic activity by increasing the H₂ yield and the CO₂/CO and the H₂/CO values while decreasing coke formation. This results from the addition of ZrO₂ into CeO₂. This promoter highlights the advantages of oxygen storage capacity and of mobile oxygen vacancies that increase the number of surface oxygen species. The addition of oxygen facilitates the reaction by regenerating the surface oxygenation of the promoters and by oxidizing surface carbon species and carbon-containing products.     

O2/CO2气氛添加CaCO3对徐州烟煤PM2.5排放的影响

采用管式炉研究了在O2/CO2气氛下添加CaCO3对PM2.5(空气动力学直径小于2.5,μm的颗粒物)排放特性的影响.试验采用荷电低压撞击器(ELPI)采集和分析燃烧后的PM2.5.结果表明,添加CaCO3是燃烧过程中影响PM2.5生成的重要因素.添加CaCO3后,生成PM1的数密度和质量浓度均降低,而PM1-2.5的数密度和质量浓度均略有增加,PM2.5粒径分布均呈双峰分布,峰值点分别出现在0.2,μm和2.0,μm左右.随着CaCO3添加质量分数的增加,PM2.5中的S、Pb、Cu、Na和K几种元素的浓度呈下降趋势.     

Rh promoted and ZrO2/Al2O3 supported Ni/Co based catalysts: High activity for CO2 reforming,steam–CO2 reforming and oxy–CO2 reforming of CH4

Ni (2.5 wt%) and Co (2.5 wt%) supported over ZrO₂/Al₂O₃ were prepared by following a hydrolytic co-precipitation method. The synthesized catalysts were further promoted by Rh incorporation (0.01–1.00 wt%) and tested for their catalytic performance for dry CO₂ reforming, combined steam–CO₂ reforming and oxy–CO₂ reforming of methane for production of syngas. The catalysts were characterized by using N₂ physical adsorption, XRD, H₂–TPR, SEM, CO₂–TPD, NH₃–TPD, TEM and TGA. The results revealed that ZrO₂ phase was in crystalline form in the catalysts along with amorphous Al oxides. Ni and Co were confirmed to be in their respective spinel phases that were reducible to metallic form at 800 °C under H₂. Ni and Co were well dispersed with their nano-crystalline nature. The catalyst with 0.2% loading of Rh showed superior performance in the studied reactions for reforming of methane. This catalyst also showed good coke resistance ability for dry CO₂ reforming reaction with 3.8 wt% of carbon formation during the reaction as compared to 11.6 wt% carbon formation over the catalyst without Rh. The catalyst performance was stable throughout the reaction time for CH₄ conversions, irrespective of carbon formation with slight decline (～1%) in CO₂ conversion. For dry CO₂ reforming reaction, this catalyst showed good conversion for both CH₄ and CO₂ (67.6% and 71.8% respectively) with a H₂/CO ratio of 0.84, while for the Oxy-CO₂ reforming reaction, the activity was superior with CH₄ and CO₂ conversions (73.7% and 83.8% respectively) and H₂/CO ratio of 1.05.     

O2/CO2气氛下生物质混煤燃烧SO2排放特性的实验研究

在水平管式炉上通过在线烟气分析仪研究了O2/CO2气氛下生物质混合比例、温度、燃烧气氛及氧浓度对生物质混煤SO2排放特性的影响规律。结果表明,O2/CO2气氛下,随着生物质混合比例的增大,生物质混煤SO2释放峰值减小,SO2排放完毕的时间减少,SO2的排放量降低;随着温度的升高,生物质混煤SO2的排放量增加。O2/CO2和O2/N2气氛下随着氧浓度的增大,生物质混煤SO2的排放量均增加。相同氧浓度时,O2/CO2气氛下生物质混煤SO2的排放量略小于O2/N2气氛下的情况,其降低幅度约为5%左右。     

Reversible hydrogenation/dehydrogenation performances of the Na2LiAlH6–Mg(NH2)2 system

Complex hydrides and Metal–N–H-based materials have attracted considerable attention due to their high hydrogen content. In this paper, a novel amide–hydride combined system was prepared by ball milling a mixture of Na₂LiAlH₆–Mg(NH₂)₂ in a molar ratio of 1:1.5. The hydrogen storage performances of the Na₂LiAlH₆–1.5Mg(NH₂)₂ system were systematically investigated by a series of dehydrogenation/hydrogenation evaluation and structural analyses. It was found that a total of ∼5.08 wt% of hydrogen, equivalent to 8.65 moles of H atoms, was desorbed from the Na₂LiAlH₆–1.5Mg(NH₂)₂ combined system. In-depth investigations revealed that the variable milling treatments resulted in the different dehydrogenation reaction pathways due to the combination of Al and N caused by the energetic milling. Hydrogen uptake experiment indicated that only ∼4 moles of H atoms could be reversibly stored in the Na₂LiAlH₆–1.5Mg(NH₂)₂ system perhaps due to the formation of AlN and Mg₃N₂ after dehydrogenation.     

高压O2/CO2气氛下煤焦理论计算研究

研究表明在6MPa压力,富氧浓度为30%的条件下的增压富氧燃烧的经济性可以达到最佳。在此气氛下用一个简单的燃烧模型对碳球燃烧的情况进行理论计算,与空气气氛下的燃烧情况作对比,得到增压富氧燃烧在煤粉的燃烧时间和对烟气捕集回收二氧化碳上的优越性。从而为增压富氧燃烧的进一步发展提供理论基础。     

O2/CO2气氛下石灰石脱硫特性的研究

在沉降炉中进行了石灰石的脱硫特性研究.表明用20%O2+80%CO2的混合气体作助燃气时比用空气作助燃气时有较好的脱硫效果,并能减少NOx的排放,是一种新的能同时控制CO2,SO2和NOx三种污染物的好方法.图8参8     

Li2CO3/Na2CO3/K2CO3及其混合熔融盐储热材料热物性分子动力学研究

对Li₂CO₃/Na₂CO₃/K₂CO₃及其二元和三元混合熔融盐的密度、比热容、黏度、热导率进行分子动力学模拟(MD),对比得出模拟结果与现有的实验数据和模拟值相近。结果表明：随着温度的升高,密度逐渐减小,离子之间的距离增加,导致对剪切应力的抵抗力变小,这说明单组分、二元和三元熔融盐黏度的负温度依赖性。对于熔融盐的热导率,单组分和二元熔融盐也呈现出负温度依赖性,而三元熔融盐趋势是随温度的升高呈上升状态。     

Syngas production by CO2 reforming of coke oven gas over Ni/La2O3–ZrO2 catalysts

Syngas production by CO₂ reforming of coke oven gas (COG) was studied in a fixed-bed reactor over Ni/La₂O₃–ZrO₂ catalysts. The catalysts were prepared by sol–gel technique and tested by XRF, BET, XRD, H₂-TPR, TEM and TG–DSC. The influence of nickel loadings and calcination temperature of the catalysts on reforming reaction was measured. The characterization results revealed that all of the catalysts present excellent resistance to coking. The catalyst with appropriate nickel content and calcination temperature has better dispersion of active metal and higher conversion. It is found that the Ni/La₂O₃–ZrO₂ catalyst with 10 wt% nickel loading provides the best catalytic activity with the conversions of CH₄ and CO₂ both more than 95% at 800 °C under the atmospheric pressure. The Ni/La₂O₃–ZrO₂ catalysts show excellent catalytic performance and anti-carbon property, which will be of great prospects for catalytic CO₂ reforming of COG in the future.     

H2 and CO production over a stable Ni–MgO–Ce0.8Zr0.2O2 catalyst from CO2 reforming of CH4

Ni–Ce_0.8Zr_0.2O₂ and Ni–MgO–Ce_0.8Zr_0.2O₂ catalysts were investigated for H₂ production from CO₂ reforming of CH₄ reaction at a very high gas hourly space velocity of 480,000 h⁻¹. Ni–MgO–Ce_0.8Zr_0.2O₂ exhibited higher catalytic activity and stability (CH₄ conversion >95% at 800 °C for 200 h). The outstanding catalytic performance is mainly due to the basic nature of MgO and an intimate interaction between Ni and MgO.     

O2/CO2/H2O气氛下CO燃烧机理的分子动力学模拟研究

采用反应分子动力学(ReaxFF MD)模拟方法研究了O₂/CO₂/H₂O气氛下CO的燃烧。结果表明：根据化学平衡原理,高浓度CO₂抑制CO的氧化,同时CO₂在高温下参与反应CO₂+H—→CO+OH,进一步抑制CO氧化。在较低温度条件下,较高浓度H₂O的三体效应显著,抑制了CO氧化。另一方面,在较高温度条件下,H₂O参与的H₂O+H—→H₂+OH和H₂O+O—→OH+OH反应占据其化学作用的主导地位,进而促进CO氧化。随着O₂浓度的增加,CO的氧化速度加快。     

O2/CO2气氛下煤燃烧NOx排放特性的实验研究

利用管式电阻炉在O₂/CO₂气氛和O₂/N₂气氛下对煤粉燃烧过程中NO_x排放特性进行实验,研究在不同停留时间、炉内燃料/氧化学当量比、温度、氧浓度等因素对燃煤过程中NO_x放特性的影响,并对这两种燃烧方式下NO_x的排放特性进行对比。结果表明:在O₂/CO₂气氛下NO_x的生成量要远远低于O₂/N₂气氛下NO_x的生成量。随着停留时间的延长,NO_x沿程释放特性是先增大后减少。随着燃料/氧化学当量比的增加,NO_x排放浓度也呈现出先增加后降低的趋势。随着炉内温度的增加,2种气氛下NO_x的排放浓度均增加。随着氧浓度的提高,NO_x排放浓度增大。     

Effects of MoS2 addition on the hydrogen storage properties of 2LiBH4–MgH2 systems

A 2LiBH₄–MgH₂–MoS₂ composite was prepared by solid-state ball milling, and the effects of MoS₂ as an additive on the hydrogen storage properties of 2LiBH₄–MgH₂ system together with the corresponding mechanism were investigated. As shown in the TG–DSC and MS results, with the addition of 20 wt.% of MoS₂, the onset dehydrogenation temperature is reduced to 206 °C, which is 113 °C lower than that of the pristine 2LiBH₄–MgH₂ system. Meanwhile, the total dehydrogenation amount can be increased from 9.26 wt.% to 10.47 wt.%, and no gas impurities such as B₂H₆ and H₂S are released. Furthermore, MoS₂ improves the dehydrogenation kinetics, and lowers the activation energy (E_a) 34.49 kJ mol⁻¹ of the dehydrogenation reaction between Mg and LiBH₄ to a value lower than that of the pristine 2LiBH₄–MgH₂ sample. According to the XRD test, Li₂S and MoB₂ are formed by the reaction between LiBH₄ and MoS₂, which act as catalysts and are responsible for the improved hydrogen storage properties of the 2LiBH₄–MgH₂ system.     

Laminar burning velocities and flame characteristics of CO–H2–CO2–O2 mixtures

Laminar burning velocities of CO–H₂–CO₂–O₂ flames were measured by using the outwardly spherical propagating flame method. The effect of large fraction of hydrogen and CO₂ on flame radiation, chemical reaction, and intrinsic flame instability were investigated. Results show that the laminar burning velocities of CO–H₂–CO₂–O₂ mixtures increase with the increase of hydrogen fraction and decrease with the increase of CO₂ fraction. The effect of hydrogen fraction on laminar burning velocity is weakened with the increase of CO₂ fraction. The Davis et al. syngas mechanism can be used to calculate the syngas oxyfuel combustion at low hydrogen and CO₂ fraction but needs to be revised and validated by additional experimental data for the high hydrogen and CO₂ fraction. The radiation of syngas oxyfuel flame is much stronger than that of syngas–air and hydrocarbons–air flame due to the existence of large amount of CO₂ in the flame. The CO₂ acts as an inhibitor in the reaction process of syngas oxyfuel combustion due to the competition of the reactions of H + O₂ = O + OH, CO + OH = CO₂ + H and H + O₂(+M) = HO₂(+M) on H radical. Flame cellular structure is promoted with the increase of hydrogen fraction and is suppressed with the increase of CO₂ fraction due to the combination effect of hydrodynamic and thermal-diffusive instability.     

Effective nanoconfinement of 2LiBH4–MgH2 via simply MgH2 premilling for reversible hydrogen storages

To improve nanoconfinement of LiBH₄ and MgH₂ in carbon aerogel scaffold (CAS), particle size reduction of MgH₂ by premilling technique before melt infiltration is proposed. MgH₂ is premilled for 5 h prior to milling with LiBH₄ and nanoconfinement in CAS to obtained nanoconfined 2LiBH₄–premilled MgH₂. Significant confinement of both LiBH₄ and MgH₂ in CAS, confirmed by SEM–EDS–mapping results, is achieved due to MgH₂ premilling. Due to effective nanoconfinement, enhancement of CAS:hydride composite weight ratio to 1:1, resulting in increase of hydrogen storage capacity, is possible. Nanoconfined 2LiBH₄–premilled MgH₂ reveals a single–step dehydrogenation at 345 °C with no B₂H₆ release, while dehydrogenation of nanoconfined sample without MgH₂ premilling performs in multiple steps at elevated temperatures (up to 430 °C) together with considerable amount of B₂H₆ release. Activation energy (E_A) for the main dehydrogenation of nanoconfined 2LiBH₄–premilled MgH₂ is considerably lower than those of LiBH₄ and MgH₂ of bulk 2LiBH₄–MgH₂ (ΔE_A = 31.9 and 55.8 kJ/mol with respect to LiBH₄ and MgH₂, respectively). Approximately twice faster dehydrogenation rate are accomplished after MgH₂ premilling. Three hydrogen release (T = 320 °C, P(H₂) = 3–4 bar) and uptake (T = 320–325 °C, P(H₂) = 84 bar) cycles of nanoconfined 2LiBH₄–premilled MgH₂ reveal up to 4.96 wt. % H₂ (10 wt. % H₂ with respect to hydride composite content), while the 1st desorption of nanoconfined sample without MgH₂ premilling gives 4.30 wt. % of combined B₂H₆ and H₂ gases. It should be remarked that not only kinetic improvement and B₂H₆ suppression are obtained by MgH₂ premilling, but also the lowest dehydrogenation temperature (T = 320 °C) among other modified 2LiBH₄–MgH₂ systems is acquired.     

Raman spectroscopic observation of dehydrogenation in ball-milled LiNH2–LiBH4–MgH2 nanoparticles

In situ Raman spectroscopy was used to monitor the dehydrogenation of ball-milled mixtures of LiNH₂–LiBH₄–MgH₂ nanoparticles. The as-milled powders were found to contain a mixture of Li₄BN₃H₁₀ and Mg(NH₂)₂, with no evidence of residual LiNH₂ or LiBH₄. It was observed that the dehydrogenation of both of Li₄BN₃H₁₀ and Mg(NH₂)₂ begins at 353 K. The Mg(NH₂)₂ was completely consumed by 415 K, while Li₄BN₃H₁₀ persisted and continued to release hydrogen up to 453 K. At higher temperatures Li₄BN₃H₁₀ melts and reacts with MgH₂ to form Li₂Mg(NH)₂ and hydrogen gas. Cycling studies of the ball-milled mixture at 423 K and 8 MPa (80 bar) found that during rehydrogenation of Li₄BN₃H₁₀ Raman spectral modes reappear, indicating partial reversal of the Li₄BN₃H₁₀ to Li₂Mg(NH)₂ transformation.     

Releasing 9.6 wt% of H2 from Mg(NH2)2–3LiH–NH3BH3 through mechanochemical reaction

Ball milling the mixture of Mg(NH₂)₂, LiH and NH₃BH₃ in a molar ratio of 1:3:1 results in the direct liberation of 9.6 wt% H₂ (11 equiv. H), which is superior to binary systems such as LiH–AB (6 equiv. H), AB–Mg(NH₂)₂ (No H₂ release) and LiH–Mg(NH₂)₂ (4 equiv. H), respectively. The overall dehydrogenation is a three-step process in which LiH firstly reacts with AB to yield LiNH₂BH₃ and LiNH₂BH₃ further reacts with Mg(NH₂)₂ to form LiMgBN₃H₃. LiMgBN₃H₃ subsequently interacts with additional 2 equivalents of LiH to form Li₃BN₂ and MgNH as well as hydrogen.