Thermal recovery effect on light-induced degradation of amorphous silicon solar module under the sunlight

The thermal recovery effect from the light-induced degradation under the sunlight is experimentally investigated on the amorphous silicon photovoltaic module (a-Si PV module) for installing directly to the roof flames of wooden houses. To enhance the recovery effect, the heat-insulating material is attached to the back side of the module for increasing the module temperature under the sunlight: the heat-insulated module.The generated power from the heat-insulated module is compared with that from the normal module (without the heat-insulating material) for 2 yr, and it has been cleared that the generated power normalized at 25°C from the heat-insulated module is approximately 7.3% higher than that from the normal one with the average temperature increase of 4.2°C under the sunlight.     

Process development of amorphous silicon/crystalline silicon solar cells

We have already investigated some crucial limiting process steps of the amorphous silicon (a-Si)/crystalline silicon (c-Si) solar cell technology and some specific characterization tools of the ultrathin amorphous material used in devices. In this work, we focus our attention particularlyon the technology of the ITO front contact fabrication, that also is used as an antireflective coating. It is pointed out that this layer acts as a barrier layer against the diffusion of metal during the annealing treatments of the front contact grid. The criteria of the selection of the metal to be used to obtain good performance of the grid and the deposition methods best suited to the purpose are shown. We were able to fabricate low temperature heterojunction solar cells based p-type Czochralski silicon, and a conversion efficiency of 14.7% on 3.8 cm² area was obtained without back surface field and texturization.     

Advances in amorphous silicon alloy cell and module technology

The low material cost and proven manufacturability of amorphous silicon (a-Si) alloy solar panels make them ideally suited for low-cost terrestrial application. A major challenge for the researchers has been how to improve the light-to-electricity conversion efeiciency. Extensive R & D efforts have resulted in a significant improvement in stable cell and module efficiencies with the achievement of 12.8% active-area cell efficiency and 10.4% module efficiency using a spectral-splitting triple-band gap, triple-cell approach. Further gains in efficiency are expected through an improved understanding of plasma chemistry and growth kinetics. In this paper, we shall discuss the progress in science and technology of a-Si alloy photovoltaics with special emphasis on the opportunities and the challenges that exist.     

The effect of spectral variations on the performance parameters of single and double junction amorphous silicon solar cells

We present the results of an experimental investigation into the effects of spectral variations in a maritime climate on the performance parameters of single and double junction amorphous silicon solar cells. Such considerations are important for accurate modelling of system performance. It is shown that one can distinguish between two effects: a primary effect that results from variations in the total irradiance in the spectrally useful range of the device, and a secondary (mismatch) effect observed in double junction devices that is related to details of device structure. Results showing the impact on the short-circuit current, the current at the maximum-power-point, the fill factor and the overall efficiency are discussed.     

Interface effects on the carrier transport and photovoltaic properties of hydrogenated amorphous silicon/crystalline silicon solar cells

Current-voltage-temperature (I-V-T) characteristics evaluated near 150K and 300K were used to study the photovoltaic property variations in hydrogenated amorphous silicon (a-Si:H)/crystalline silicon (c-Si) solar cells. The possible carrier transport mechanisms in such devices were examined from the I-V-T data which indicated a significant influence of the amorphous /crystalline interface on the short-circuit current density (J_sc) and open-circuit voltage (V_oc) of the solar cells. Carrier transport near 300K for forward biases was by a multi-tunneling mechanism and became space charge limited with increasing bias. For devices having low J_sc and V_oc an additional region was seen in both forward and reverse biases, at low temperatures, where the current simply varied linearly with the applied bias. This characteristic manifested in both high and low temperatures region for devices with still lower photovoltaic properties, which has been reasoned to be due to a higher interface density. Passivating the c-Si surface with HF just prior to the amorphous layer deposition resulted in a large improvement in the properties. The most significant effect was on the J_sc which improved by an order of magnitude. The treatment also affected the lower temperature I-V-T data in that the current fell to very low levels. The spectral response of the treated solar cells showed enhanced blue/violet response compared with the unpassivated devices. The interface passivation plus reducing a-Si thickness has improved the solar cell efficiency from 0.39% to 9.5%.     

Low-temperature deposition of amorphous silicon solar cells

We develop amorphous silicon (a-Si:H)-based solar cells by plasma-enhanced chemical vapor deposition (PECVD) at deposition temperatures of T_s=75°C and 100°C, compatible with low-cost plastic substrates. The structural and electronic properties of low-temperature standard PECVD a-Si:H, both doped and undoped, prevent the photovoltaic application of this material. In this paper, we demonstrate how to achieve device-quality a-Si:H even at low deposition temperatures. In the first part, we show the dependence of structural and carrier transport properties on the deposition temperature. The sub-band gap absorption coefficient and the Urbach energy increase when the deposition temperature declines from T_s=150°C to 50°C, the conductivity of doped layers and mobility-lifetime product of intrinsic a-Si:H drop drastically. Therefore, in the second part we investigate the impact of increasing hydrogen dilution of the feedstock gases on the properties of low-temperature a-Si:H. We restore n-type a-Si : H device-quality conductivity while the p-type a-Si:H conductivity is still inferior. For undoped layers, we depict the hole diffusion length, the mobility-lifetime product for electrons, the Urbach energy, and sub-band gap absorption coefficient as a function of the hydrogen dilution ratio. We incorporate these optimized materials in solar cell structures of single and multilayer design and record initial efficiencies of η=6.0% at a deposition temperature of T_s=100°C, and η=3.8% at T_s=75°C. For prospective opaque polymer substrates we develop, in addition to our conventional pin cells, devices in nip design with similar performance.     

Amorphous silicon/p-type crystalline silicon heterojunction solar cells with a microcrystalline silicon buffer layer

Undoped hydrogenated amorphous silicon (a-Si:H)/p-type crystalline silicon (c-Si) structures with and without a microcrystalline silicon (μc-Si) buffer layer have been investigated as a potential low-cost heterojunction (HJ) solar cell. Unlike the conventional HJ silicon solar cell with a highly doped window layer, the undoped a-Si:H emitter was photovoltaically active, and a thicker emitter layer was proven to be advantageous for more light absorption, as long as the carriers generated in the layer are effectively collected at the junction. In addition, without using heavy doping and transparent front contacts, the solar cell exhibited a fill factor comparable to the conventional HJ silicon solar cell. The optimized configuration consisted of an undoped a-Si:H emitter layer (700 Å), providing an excellent light absorption and defect passivation, and a thin μc-Si buffer layer (200 Å), providing an improved carrier collection by lowering barrier height at the interface, resulting in a maximum conversion efficiency of 10% without an anti-reflective coating.     

An amorphous silicon random nanocone/polymer hybrid solar cell

This paper proposes and experimentally demonstrates an a-Si:H random nanocone/PEDOT:PSS/P3HT:PCBM hybrid solar cell to extend the absorption to near infrared and solve the difficulty of carrier transport through organic-inorganic interface. The internal electrical field inside a-Si:H random nanocone force holes move to the anode and electrons move to the cathode. The insertion of a layer of PEDOT:PSS conducting polymer between organic-inorganic interface could cause electrons and holes to partially recombine, thus establishing an electrically connected a-Si:H and P3HT:PCBM bulk heterojunction, which enables carriers transport through organic-inorganic interfaces efficiently. As compared to conventional polymer solar cells, the open-circuit voltage of hybrid solar cells was increased from 0.51 to 0.78 V. Additionally, the power conversion efficiency was increased from 1.73% to 2.22%, which demonstrates approximately 28% enhancement, indicating that the hybrid structure could largely increase the efficiency of polymer solar cells.     

Modeling of light-induced degradation of amorphous silicon solar cells

Light-induced degradation of hydrogenated amorphous silicon (a-Si:H) solar cells has been modeled using computer simulations. In the computer model, the creation of light-induced defects as a function of position in the solar cell was calculated using the recombination profile. In this way, a new defect profile in the solar cell was obtained and the performance was calculated again. The results of computer simulations were compared to experimental results obtained on a-Si:H solar cell with different intrinsic layer thickness. These experimental solar cells were degraded under both open- and short-circuit conditions, because the recombination profile in the solar cells could then be altered significantly. A reasonable match was obtained between the experimental and simulation results if only the mid-gap defect density was increased. To our knowledge, it is the first time that light-induced degradation of the performance and the quantum efficiency of a thickness series of a-Si:H solar cells has been modeled at once using computer simulations.     

Voltage-dependent quantum efficiency measurements of amorphous silicon multi-junction mini-modules

Multi-junction solar cells have the potential to provide higher efficiencies than single junction devices and to reduce the impact of Staebler-Wronski degradation on amorphous silicon (a-Si) devices. They could, therefore, reduce the cost of solar electricity. However, their characterization presents additional challenges over that of single junction devices. Achieving acceptable accuracy of any current-voltage calibration requires correction of the current-voltage data with external quantum efficiency measurements and spectral mismatch calculations. This paper presents voltage-dependent EQE curves for both single junction and double junction a-Si solar cells, along with dispersion curves extracted from these data. In the case of single junction a-Si devices the mismatch factor is known to be voltage-dependent and a similar trend is shown to apply to multi-junction devices as well. However, the error introduced into current-voltage calibrations due to this bias dependence is found to be <1% for spectral mismatch calculations.     

Theory of amorphous silicon solar cell (b): a five layer analytical model

A theoretical analysis of recombination kinetics and space charge distribution in amorphous silicon is carried out with a view to bring out the underlying physics. A uniform excitation with a flat quasi-Fermi level and a constant np product has been used as a probe to estimate the relative importance of various parameters. Recombination rates have been calculated for various ratios of capture rates for Coulomb attractive and neutral traps. In practice a large ratio of capture rates exists and for this case two peaks of recombination maxima are found to lie in the space charge regions corresponding to transitions at the energy level E₁ (for D⁺–D⁰ transition) at the p–i edge and for E₂ energy level (corresponding to D⁰–D⁻ transition) at the i–n interface. A two independent level model therefore holds to a good approximation. The dangling bond density is found to determine both the space charge distribution and the recombination rate. Based on space charge density distribution i-layer can be divided in the five parts. The two recombination rate peaks are found to exist at the p–i and i–n space charge transitions respectively. This enables us to develop a simple model for the i-layer of the p–i–n diode.     

A high efficiency thin film silicon solar cell and module

A photoelectric conversion efficiency of over 10% has been achieved in thin-film microcrystalline silicon solar cells which consist of a 2 μm thick layer of polycrystalline silicon. It was found that an adequate current can be extracted even from a thin film due to the very effective light trapping effect of silicon with a low absorption coefficient. As a result, this technology may eventually lead to the development of low-cost solar cells. Also, an initial aperture efficiency as high as 13.5% has been achieved with a large area (91 cm × 45 cm) tandem solar cell module of microcrystalline silicon and amorphous silicon (thin film Si hybrid solar cell). An even greater initial efficiency of 14.7% has been achieved in devices with a small size (area of 1 cm²), and further increases of efficiency can be expected.     

Development of thin film amorphous silicon oxide/microcrystalline silicon double-junction solar cells and their temperature dependence

We have developed thin film silicon double-junction solar cells by using micromorph structure. Wide bandgap hydrogenated amorphous silicon oxide (a-SiO:H) film was used as an absorber layer of top cell in order to obtain solar cells with high open circuit voltage (V_oc), which are attractive for the use in high temperature environment. All p, i and n layers were deposited on transparent conductive oxide (TCO) coated glass substrate by a 60 MHz-very-high-frequency plasma enhanced chemical vapor deposition (VHF-PECVD) technique. The p-i-n-p-i-n double-junction solar cells were fabricated by varying the CO₂ and H₂ flow rate of i top layer in order to obtain the wide bandgap with good quality material, which deposited near the phase boundary between a-SiO:H and hydrogenated microcrystalline silicon oxide (μc-SiO:H), where the high V_oc can be expected. The typical a-SiO:H/μc-Si:H solar cell showed the highest initial cell efficiency of 10.5%. The temperature coefficient (TC) of solar cells indicated that the values of TC for conversion efficiency (η) of the double-junction solar cells were inversely proportional to the initial V_oc, which corresponds to the bandgap of the top cells. The TC for η of typical a-SiO:H/μc-Si:H was −0.32%/ °C, lower than the value of conventional a-Si:H/μc-Si:H solar cell. Both the a-SiO:H/μc-Si:H solar cell and the conventional solar cell showed the same light induced degradation ratio of about 20%. We concluded that the solar cells using wide bandgap a-SiO:H film in the top cells are promising for the use in high temperature regions.     

Fabrication of amorphous silicon p-i-n solar cells using ion shower doping technique

We have studied the fabrication of amorphous silicon (a-Si : H) p-i-n solar cells using an ion shower doped n⁺-layer. The p-i-n cells with ion-doped n⁺-layer exhibited open-circuit voltage of > 0.8 V, fill factor of > 0.62 and conversion efficiency of > 8.4% when the ion acceleration voltage was between 3 and 7 kV. The a-Si : H p-i-n solar cell fabricated under an optimized ion-doping condition exhibited an open-circuit voltage of 0.84 V, a fill factor of 0.66 and a conversion efficiency of 9.9% which was very similar to those of conventional a-Si : H p-i-n cells fabricated in the same deposition chamber. Therefore, ion shower doping technique can be applied to fabricate large area, high performance a-Si : H p-i-n solar cells.     

Influence of defects and band offsets on carrier transport mechanisms in amorphous silicon/crystalline silicon heterojunction solar cells

We have investigated the carrier transport mechanisms in undoped a-Si:H/p-type c-Si heterojunctions with and without a μc-Si buffer layer, as well as their effects on the photovoltaic properties of the junction. The conduction behavior of the junction is strongly affected by the defect state distribution and band offset at the hetero-interface. The recombination process involving the interface states on the thin film silicon (a-Si:H/μc-Si) side dominates at low forward bias (V<0.3 V), whereas multistep tunneling capture emission (MTCE) dominates in the higher bias region (0.3<V<0.55 V) until the conduction becomes space charge limited (V>0.55 V). The MTCE process seems to be more closely related to the bulk defects in the thin film silicon than the interface states. In addition, the position of a trapping level, where the tunneling process occurs, seems to be determined by the hole energy at the edge of the c-Si and the trap distribution in the thin film silicon. Despite the domination of MTCE in the indicated voltage range, the reduced band offset at the interface increases current levels by the enhanced diffusion and/or emission processes. The insertion of a 200 Å thick μc-Si buffer layer between the a-Si:H (700 Å)/c-Si increases the solar cell efficiency to 10%, without an antireflective coating, by improving both the carrier transport and the red response of the cell.     

Performance of p-type silicon-oxide windows in amorphous silicon solar cell

a-SiO_x films have been prepared using silane and pure oxygen as reactive gases in plasma CVD system. Diborane was introduced as a doping gas to obtain p-type conduction silicon oxide. Infrared absorption spectra show the incorporation of Si–O stretch mode around 1000 cm⁻¹. The optical bandgap increases with the oxygen to silane gas ratio, while the electrical conductivity decreases. Hydrogenated amorphous silicon solar cells have been fabricated using p-type a-SiO_x with around 1.85 eV optical bandgap and conductivity greater than 10⁻⁷ S/cm. The measured current–voltage characteristics of the solar cells under 100 mW/cm² artificial light are V_oc=0.84 V, J_sc=14.7 mA/cm², FF=0.635 with a conversion efficiency of 7.84%.     

Amorphous silicon/p-type crystalline silicon heterojunction solar cells

We have investigated the photovoltaic (PV) characteristics of both glow discharge deposited hydrogenated amorphous silicon (a-Si:H) on crystalline silicon (c-Si) in a n⁺ a-Si:H/undoped a-Si:H/p c-Si type structure, and DC magnetron sputtered a-Si:H in a n-type a-Si:H/p c-Si type solar cell structure. It was found that the PV properties of the solar cells were influenced very strongly by the a-Si/c-Si interface. Properties of strongly interface limited devices were found to be independent of a-Si thickness and c-Si resistivity. A hydrofluoric acid passivation prior to RF glow discharge deposition of a-Si:H increases the short circuit current density from 2.57 to 25.00 mA/cm² under 1 sun conditions.DC magnetron sputtering of a-Si:H in a Ar/H₂ ambient was found to be a controlled way of depositing n type a-Si:H layers on c-Si for solar cells and also a tool to study the PV response with a-Si/c-Si interface variations. 300 Å a-Si sputtered onto 1–10 ω cm p-type c-Si resulted in 10.6% efficient solar cells, without an A/R coating, with an open circuit voltage of 0.55 V and a short circuit current density of 30 mA/cm² over a 0.3 cm² area. High frequency capacitance-voltage measurements indicate good junction characteristics with zero bias depletion width in c-Si of 0.65 μm. The properties of the devices have been investigated over a wide range of variables like substrate resistivity, a-Si thickness, and sputtering power. The processing has focused on identifying and studying the conditions that result in an improved a-Si/c-Si interface that leads to better PV properties.     

Amorphous silicon solar cells

The perfectioning of the deposition techniques of amorphous silicon over large areas, in particular film homogeneity and the reproducibility of the electro-optical characteristics, has allowed a more accurate study of the most intriguing bane of this material: the degradation under sun-light illumination. Optical band-gap and film thickness engineering have enabled device efficiency to stabilize with only a 10–15% loss in the as-deposited device efficiency. More sophisticated computer simulations of the device have also strongly contributed to achieve the highest stable efficiencies in the case of multijunction devices. Novel use of nanocrystalline thin films offers new possibilities of high efficiency and stability. Short term goals of great economical impact can be achieved by the amorphous silicon/crystalline silicon heterojunction. A review is made of the most innovative achievements in amorphous silicon solar cell design and material engineering.     

Crystalline silicon surface passivation by amorphous silicon carbide films

This article reviews the surface passivation of n- and p-type crystalline silicon by hydrogenated amorphous silicon carbide films, which provide surface recombination velocities in the range of 10 cm s⁻¹. Films are deposited by plasma-enhanced chemical vapor deposition from a silane/methane plasma. We determine the passivation quality measuring the injection level (Δn)-dependent lifetime (τ_eff(Δn)) by the quasi-steady-state photoconductance technique. We analyze the experimental τ_eff(Δn)-curves using a physical model based on an insulator/semiconductor structure and an automatic fitting routine to calculate physical parameters like the fundamental recombination velocities of electrons and holes and the fixed charge created in the film. In this way, we get a deeper insight into the effect of the deposition temperature, the gas flow ratio, the doping density of the substrate and the film thickness on surface passivation quality.     

Hydrogenated amorphous silicon films with significantly improved stability

A new regime of plasma-enhanced chemical-vapor deposition (PECVD), referred to as “uninterrupted growth/annealing” method, has been proposed for preparation of high-quality hydrogenated amorphous silicon (a-Si:H) films. By using this regime, the deposition process no longer needs to be interrupted, as done in the chemical annealing or layer by layer deposition, while the growing surface is continuously subjected to an enhanced annealing treatment with atomic hydrogen created in the hydrogen-diluted reactant gas mixture at a relatively high plasma power. The intensity of the hydrogen plasma treatment is controlled at such a level that the deposition conditions of the resultant films approach the threshold for microcrystal formation. In addition, a low level of B-compensation is used to adjust the position of the Fermi level close to the midgap. Under these conditions, we find that the stability and optoelectronic properties of a-Si:H films have been significantly improved.