Soft switching resonant converter with duty-cycle control in DC micro-grid system

Resonant converter has been widely used for the benefits of low switching losses and high circuit efficiency. However, the wide frequency variation is the main drawback of resonant converter. This paper studies a new modular resonant converter with duty-cycle control to overcome this problem and realise the advantages of low switching losses, no reverse recovery current loss, balance input split voltages and constant frequency operation for medium voltage direct currentgrid or system network. Series full-bridge (FB) converters are used in the studied circuit in order to reduce the voltage stresses and power rating on power semiconductors. Flying capacitor is used between two FB converters to balance input split voltages. Two circuit modules are paralleled on the secondary side to lessen the current rating of rectifier diodes and the size of magnetic components. The resonant tank is operated at inductive load circuit to help power switches to be turned on at zero voltage with wide load range. The pulse-width modulation scheme is used to regulate output voltage. Experimental verifications are provided to show the performance of the proposed circuit.     

Interleaved soft switching resonant converter with a small input ripple current

ABSTRACT

An interleaved frequency control soft switching converter is studied for solar power or fuel cell power applications. The proposed circuit topology contains two parallel current-fed circuit cells with interleaved pulse-width modulation operation. Thus, the ripple currents at input and output terminals are decreased. In each circuit cell, the proposed current-fed dc-dc converter includes boost circuit and resonant circuit to achieve current ripple-free on low voltage side and less switching losses on active devices. The boost circuit and the resonant circuit have same active devices to decrease power switches. Due to the resonant behaviour, the reverse recovery current loss on secondary diodes is removed. The voltage doubler circuit topology is accomplished on secondary-side to reduce diode counts and conduction loss. The performance and effectiveness of the developed interleaved PWM current-fed converter are verified and confirmed by experiments.     

A zero-voltage-switched PWM boost converter with an energyfeedforward auxiliary circuit

A zero-voltage-switched (ZVS) pulsewidth-modulated (PWM) boost converter with an energy feedforward auxiliary circuit is proposed in this paper. The auxiliary circuit, which is a resonant circuit consisting of a switch and passive components, ensures that the converter's main switch and boost diode operate with soft switching. This converter can function with PWM control because the auxiliary resonant circuit operates for a small fraction of the switching cycle. Since the auxiliary circuit is a resonant circuit, the auxiliary switch itself has both a soft turn on and turn off, resulting in reduced switching losses and electromagnetic interference (EMI). This is unlike other proposed ZVS boost converters with auxiliary circuits where the auxiliary switch has a hard turn off. Peak switch stresses are only slightly higher than those found in a conventional PWM boost converter because part of the energy that would otherwise circulate in the auxiliary circuit and drastically increase peak switch stresses is fed to the load. In this paper, the operation of the converter is explained and analyzed, design guidelines are given, and experimental results obtained from a prototype are presented. The proposed converter is found to be about 2%-3% more efficient than the conventional PWM boost converter     

一种新型软开关DC-DC PWM升压变换器设计

为提高转换效率并降低电源开关的电流应力,提出一种基于新型有源缓冲电路的PWM DC-DC升压变换器。该有源缓冲电路使用ZVT—ZCT软开关技术,分别提供了总开关ZVT开启及ZCT闭合、辅助开关ZCS开启及ZCT闭合。消除了总开关额外的电流及电压应力,消除了辅助开关电压应力,且有源缓冲电路的耦合电感降低了电流应力。另外,通过连续将二极管添加到辅助开关电路,防止来自共振电路的输入电流应力进入总开关。实验结果表明,相比传统的PWM变换器,新的DC-DC PWM升压变换器在满负荷时电流应力降低且总体效率能达到98.7%。     

Resonant link bidirectional power converter. I. Resonant circuit

This paper proposes a novel resonant circuit capable of PWM operation with zero switching losses. The resonant circuit is aimed at providing zero voltage intervals in the DC link of the PWM converter during the required converter device switching periods, and it gives minimum DC bus voltage stresses and minimum peak resonant current. It requires only two additional switches compared to a conventional PWM converter. It is observed that the resonant circuit guarantees the soft switching of all the switching power devices of converters including the switches for resonant operation. Simulation results and experimental results are presented to verify the operating principles     

低损耗软开关Boost变换器

介绍一种新的软开关Boost变换器。传统的Boost变换器在开通和关断时将产生开关损耗,因此使整个系统的效率下降。新的Boost变换器利用软开关方法增加了辅助开关管和谐振电路。这样,相比硬开关情况下,变换器减小了开关损耗。这种变换器可以应用在光伏系统、功率因子校正等装置中。详细分析电路的工作原理以及实现软开关的条件,利用Pspice9．2软件进行仿真验证。仿真结果表明,该变换器的所有开关器件都实现了软开关,从而使效率得到提高。     

A new active clamping zero-voltage switching PWM current-fed half-bridge converter

A new active clamping zero-voltage switching (ZVS) pulse-width modulation (PWM) current-fed half-bridge converter (CFHB) is proposed in this paper. Its active clamping snubber (ACS) can not only absorb the voltage surge across the turned-off switch, but also achieve the ZVS of all power switches. Moreover, it can be applied to all current-fed power conversion topologies and its operation as well as structure is very simple. Since auxiliary switches in the snubber circuit are switched in a complementary way to main switches, an additional PWM IC is not necessary. In addition, it does not need any clamp winding and auxiliary circuit besides additional two power switches and one capacitor while the conventional current-fed half bridge converter has to be equipped with two clamp windings, two ZVS circuits, and two snubbers. Therefore, it can ensure the higher operating frequency, smaller-sized reactive components, lower cost of production, easier implementation, and higher efficiency. The operational principle, theoretical analysis, and design considerations are presented. To confirm the operation, validity, and features of the proposed circuit, experimental results from a 200-W, 24-200Vdc prototype are presented.     

Novel zero-voltage and zero-current-switching (ZVZCS) full-bridge PWM converter using coupled output inductor

A novel zero-voltage and zero-current-switching (ZVZCS) full-bridge pulse-width-modulated (PWM) converter is proposed to improve the previously proposed ZVZCS full-bridge PWM converters. By employing a simple auxiliary circuit with neither lossy components nor active switches, soft-switching of the primary switches is achieved. The proposed converter has many advantages such as simple auxiliary circuit, high efficiency, low voltage stress of the rectifier diode and self-adjustment of the circulating current, which make the proposed converter attractive for the high voltage and high power applications. The principles of operation and design considerations are presented and verified on the 4 kW experimental converter operating at 80 kHz.     

Parallel resonant DC link circuit-a novel zero switching losstopology with minimum voltage stresses

A parallel resonant DC link (PRDCL) circuit topology is proposed as an approach to realizing zero switching loss DC-AC high switching frequency power conversion. The proposed circuit is used as an interface between the DC voltage supply and a voltage source pulse width modulated (PWM) inverter to provide a short zero voltage period in the DC link of the inverter to allow zero voltage switchings to take place in the PWM inverter. The peak voltage stress on the PWM inverter switches is limited to the DC supply voltage. Another significant advantage of the circuit is that the inverter can be controlled by the conventional PWM strategy. The proposed circuit is systematically analyzed and its operation principle is explained. Design considerations and design formulas are presented. A complete zero voltage switching DC-AC system consisting of the proposed circuit and a PWM inverter was simulated on a computer     

Design and Application for PV Generation System Using a Soft-Switching Boost Converter With SARC

In order to improve the efficiency of energy conversion for a photovoltaic (PV) system, a soft-switching boost converter using a simple auxiliary resonant circuit, which is composed of an auxiliary switch, a diode, a resonant inductor, and a resonant capacitor, is adopted in this paper. The conventional boost converter decreases the efficiency because of hard switching, which generates losses when the switches are turned on/off. During this interval, all switches in the adopted circuit perform zero-current switching by the resonant inductor at turn-on, and zero-voltage switching by the resonant capacitor at turn-off. This switching pattern can reduce the switching losses, voltage and current stress of the switching device. Moreover, it is very easy to control. In this paper, we have analyzed the operational principles of the adopted soft-switching boost converter, and it is designed for PV generation system. Simulation and experimental results are presented to confirm the theoretical analysis.      

Novel zero-voltage and zero-current-switching full bridge PWMconverter using transformer auxiliary winding

A novel zero voltage and zero current switching (ZVZCS) full bridge (FB) pulse width modulation (PWM) converter is proposed to improve the demerits of the previously presented ZVZCS-FB-PWM converters, such as use of lossy components or additional active switches. A simple auxiliary circuit which includes neither lossy components nor active switches provides ZVZCS conditions to primary switches, ZVS for leading-leg switches and ZCS for lagging-leg switches. Many advantages including simple circuit topology, high efficiency, and low cost make the new converter attractive for high power (>2 kW) applications. The operation, analysis, features and design considerations are illustrated and verified on a 2.5 kW, 100 kHz insulated gate bipolar transistor (IGBT) based experimental circuit     

电流型零电压开关节能整流器

为解决电流型脉冲宽度调制（Pulse Width Modulation,PWM）整流器在高开关频率下硬切换时的开关损耗问题,提出了一种电流型零电压开关节能整流器,其辅助谐振电路位于直流环节,且与直流母线并联,只有1个辅助开关.在换流过程中,主开关能实现零电压切换,辅助开关能实现零电流切换,而且当整流器采用多电平PWM控制策略时,辅助电路在每个开关周期只需工作1次.分析了谐振换流过程,仿真结果表明特征仿真波形符合理论分析,开关器件切换时处于软开关状态,整流器能平稳运行.该电流型零电压开关节能整流器可以在高开关频率和大功率的应用场合实现高效率运行.     

有源箝位软开关充电机的设计与仿真研究

传统硬开关电路影响效率和可靠性的同时,对其他设备的电磁干扰也较大,软开关则可解决上述问题。本文提出了一种基于辅助谐振换流的新型ZVT-PWM变换器,即通过采用简单的有源辅助谐振网络实现了主、辅开关管的软开关,主开关管实现了零电压开通,开关管电流电压应力小。利用这种软开关技术研制了一台用于为风力发电蓄电池充电的充电机,给出了充电机的控制系统框图,简单介绍了充电机的工作原理。最后利用Pspice给出了运行波形和仿真结果。     

A novel ZCS-PWM power-factor preregulator with reduced conduction losses

This paper proposes a new single-phase high-power-factor rectifier, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current-switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the active switches and zero-voltage switching in the passive switches. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Nine transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM switch model is used to predict the system performance. A prototype rated at 1 kW, operating 50 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage 400 V/sub dc/ has been implemented in laboratory. An efficiency of 97.3% and power factor over 0.99 has been measured. Analysis, design, and the control circuitry are also presented in this paper.     

Auxiliary resonant commutated pole inverter using two internalvoltage-points of DC source

This paper presents a new auxiliary resonant commutated pole inverter that has series-connected batteries as the DC source. This inverter has two main switches and two auxiliary switches, and of all these devices achieve soft switching. The resonant operations are employed only during the commutating intervals; therefore, pulsewidth modulation (PWM) can be applied to the circuit. This circuit has the feature of using two internal voltage points of the DC source. Consequently, the circuit has the advantages of stability, simplicity in control, and high efficiency. The principle of the circuit operation and the experimental results are described in this paper     

Electronic step down (220/110 V) transformer using a new quantumseries resonant converter

A novel quantum series resonant converter (QSRC) topology for a pure sinewave 60 Hz AC chopper is proposed. It has three bidirectional switches and operates at high switching frequency with low switching loss. Bidirectional power flow is possible, and the switches can operate in either zero current switching (ZCS) mode or zero voltage switching (ZVS) mode by slight modification. The QSRC is thought to be suitable for such a system with fixed voltage conversion ratio. The proposed converter is applied to an electronic 220/110 V transformer. Detailed analyses and experimental results for 1 kVA are presented     

A new single-phase ZCS-PWM boost rectifier with high power factor and low conduction losses

This paper proposes a new single-phase high-power-factor rectifier, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the active switches and zero-voltage switching (ZVS) in the passive switches. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved because of the following reasons: 1) the circulating current for the soft switching flows only through the auxiliary circuit; 2) a minimum number of switching devices are involved in the circulating current path; and 3) the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Seven transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM-switch model is used to predict the system performance. A prototype rated at 1 kW, operating at 60 kHz, with an input alternating current voltage of 220 V/sub rms/ and an output voltage of 400 V/sub dc/, has been implemented in laboratory. An efficiency of 98.3% and a power factor over 0.99 have been measured. Analysis, design, and the control circuitry are also presented in this paper.     

A three-phase soft-transition inverter with a novel controlstrategy for zero-current and near zero-voltage switching

This paper proposes a new soft-transition control strategy for a three-phase zero-current-transition (ZCT) inverter circuit. Each phase leg of the inverter circuit consists of an LC resonant tank, two main switches, and two auxiliary switches. The proposed strategy is realized by planning the switching patterns and timings of these four switches based on the load current information. It enables all the main switches and auxiliary switches to be turned on and turned off under zero-current conditions, and achieves a near zero-voltage turn-on for the main switches. Compared with existing ZCT strategies, the diode reverse recovery current and switching turn-on loss are substantially reduced, the current and thermal stresses in the auxiliary devices are evenly distributed over every switching cycle, and the resonant capacitor voltage stress is reduced from twice the DC bus voltage to 1.3-1.4 times the DC bus voltage. The proposed strategy is also suitable for three-phase power-factor-correction (PFC) rectifier applications. The operation principles, including a detailed analyst based on the state-plane technique, and a design rule are described in this paper. The circuit operation is first verified by a computer simulation, and is then tested with a 50-kW three-phase inverter to the full power level together with a three-phase induction motor in a closed-loop speed/torque control. Significant reductions in switching losses and voltage/current stresses over existing techniques have been experimentally demonstrated     

A novel zero-Voltage-switching PWM boost rectifier with high power factor and low conduction losses

This paper proposes a new single-phase high-power-factor rectifier, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-voltage-switching PWM (ZVS-PWM) auxiliary circuit is configured in the presented ZVS-PWM rectifier to perform ZVS in the main switches and the passive switches, and zero-current switching in the auxiliary switch. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZVS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path, and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Nine transition states for describing the behavior of the ZVS-PWM rectifier in one switching period are described. A prototype rated at 1 kW, operating 80 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage of 400 V/sub dc/ has been implemented in the laboratory. An efficiency of 96.7% and power factor over 0.99 has been measured. Analysis, design, and the control circuitry are also presented in this paper.     

A novel self-oscillating, boost-derived DC-DC converter with load regulation

This paper proposes a novel self-oscillating, boost-derived (SOBD) dc-dc converter with load regulation. This proposed topology utilizes saturable cores (SCs) to offer self-oscillating and output regulation capabilities. Conventionally, the self-oscillating dc transformer (SODT) type of scheme can be implemented in a very cost-effective manner. The ideal dc transformer provides both input and output currents as pure, ripple-free dc quantities. However, the structure of an SODT-type converter will not provide regulation, and its oscillating frequency will change in accordance with the load. The proposed converter with SCs will allow output-voltage regulation to be accomplished by varying only the control current between the transformers, as occurs in a pulse-width modulation (PWM) converter. A control network that combines PWM schemes with a regenerative function is used for this converter. The optimum duty cycle is implemented to achieve low levels of input- and output-current ripples, which are characteristic of an ideal dc transformer. The oscillating frequency will spontaneously be kept near-constant, regardless of the load, without adding any auxiliary or compensation circuits. The typical voltage waveforms of the transistors are found to be close to quasisquare. The switching surges are well suppressed, and the voltage stress of the component is well clamped. The turn-on/turn-off of the switch is zero-voltage switching (ZVS), and its resonant transition can occur over a wide range of load current levels. A prototype circuit of an SOBD converter shows 86% efficiency at 48-V input, with 12-V, 100-W output, and presents an operating frequency of 100 kHz.