Mg60Cu30Y10块体非晶合金的变温晶化行为

采用示差扫描量热仪(DSC)得到Mg60Cu30Y10块体非晶合金在不同加热速率下的DSC曲线。利用Losocka、Kissinger以及Doyle方法研究了Mg60Cu30Y10块体非晶合金的非等温晶化动力学。结果表明:Mg60Cu30Y10块体非晶合金具有良好的热稳定性。通过Kissinger方法计算得到的其玻璃转变激活能(Eg)、晶化激活能(Ex)以及晶化峰值激活能(Ep)分别为160.07 kJ/mol、136.11和145.19 kJ/mol。随着加热速率的提高,各特征温度值向高温端移动。局域晶化激活能随着复合材料晶化体积分数的增加先增大后减小。     

不同形态和热历史条件下Zr55Al10Ni5Cu30非晶合金的晶化行为

研究了不同形态Zr₅₅Al₁₀Ni₅Cu₃₀非晶合金（块体和粉末）在不同升温和冷却条件下的晶化行为.发现Zr₅₅Al₁₀-Ni₅Cu₃₀在不同热历史下的晶化行为有较大差别.对于块体非晶合金,在常规热处理条件下,合金的升温和冷却速率较低,Zr₅₅Al₁₀Ni₅Cu₃₀块体非晶合金在初始晶化温度Tx以上开始晶化,形成CuZr₂纳米晶.随着热处理温度的升高,晶粒尺寸增大,当热处理最终温度超过熔点后,合金在随炉冷却过程中形成了粗大的CuZr₂板条+板条间（CuZr₂）+（Zr,Cu,Al,Ni）共晶组织;在激光熔凝条件下,合金的升温和冷却速率较高,Zr₅₅Al₁₀Ni₅Cu₃₀块体非晶合金随单点熔凝次数的增加,晶化效应逐渐累加,热影响区中逐渐出现微米级球晶的弥散析出,并长大,随后失稳形成沿熔池边界带状分布,尺寸可达几百微米的等轴晶.对于粉末非晶合金,由于Zr₅₅Al₁₀Ni₅Cu₃₀非晶粉末的冷却强度不如块体非晶,冷却速率较块体低,造成粉末颗粒在激光熔凝过程中晶化为微米级的等轴枝晶,并随着激光能量的升高,等轴枝晶尺寸增大.     

电脉冲孕育处理对Zr基块体非晶热稳定性及退火晶化的影响

通过先对Zr55Ni5Al10Cu30合金熔体施加脉冲电流处理,再利用非真空吸铸法制备出Zr55Ni5Al10Cu30块体非晶合金的方式,研究了电脉冲孕育处理对非晶热稳定性及退火晶化的影响。差分扫描量热(DSC)及X射线衍射(XRD)分析结果表明:经电脉冲孕育处理后Zr55Ni5Al10Cu30块体非晶合金的玻璃转变温度上升,晶化温度降低,过冷液相区变窄,同时玻璃转变激活能和晶化激活能有所减少。电脉冲孕育处理没有改变Zr55Ni5Al10Cu30块体非晶合金退火晶化相演变过程,但提高了非晶退火晶化率。电脉冲孕育处理对Zr55Ni5Al10Cu30块体非晶合金的晶化起到了促进作用。     

块体非晶合金Cu58 Zr30 Ti10 Sn2的形成与晶化行为研究

采用铜模吸铸法制备了直径为2～3mm的圆柱状Cu60-xZr30Ti10Snx（x=0、1、2）块体非晶合金。用X射线衍射（XRD）和差式扫描量热仪（DSC）研究了非晶合金的结构、热稳定性和晶化特征，非晶合金Cu60-xZr30Ti10Snx的特征温度Tg、Tx、△Tx=（Tx-Tg）均与Sn含量相关。块体非晶合金Cu58Zr30Ti10Sn2的Tg为703．9K、Tx为755．5K、△Tx约为51．6K。这些特征温度随DSC升温速率的增大，不断向高温区偏移，其中晶化行为的这种动力学效应比其玻璃转变的更为显著。由Kissinger法获得的块体非晶合金Cu58Zr30Ti10Sn2的玻璃转变激活能Eg为3．30eV、晶化激活能Ex为3．17eV、第一晶化峰激活能Ep1为2．82eV、第二晶化峰激活能Ep2为3．13eV。由Ozawa法获得的各激活能比Kissinger法的相应数值稍偏低，但趋势是一致的。     

熔盐电解制备低成本Ti12LC钛合金的研究

利用覆盖渣技术在非真空条件下成功制备出了直径为3 mm的Zr55Ni5Al10Cu30块体非晶合金.采用差示扫描量热法(DSC),将Johnson-Mehl-Avrami理论拓展应用于非晶合金的非等温晶化过程研究.结果表明,Zr55Ni5Al10Cu30块体非晶合金的连续升温晶化过程Avrami指数及形核率随升温速率的升高而呈下降趋势,同时随晶化过程进行呈先增加后减小的规律.Avrami指数最大值出现在晶化体积分数0.3～0.4之间,在低升温速率下Zr55Ni5Al10Cu30块体非晶合金部分晶化过程出现三维形核界面控制长大的形式.     

Mg61Cu28Gd11和(Mg0.61Cu0.28Gd0.11)99.5Sb0.5非晶合金的晶化动力学和腐蚀行为（英文）

研究0.5%(摩尔分数)Sb的引入对Mg61Cu28Gd11块体非晶合金性能的影响。利用差热扫描量热仪测试样品的晶化动力学。结果表明:在等时加热的过程中,非晶合金的玻璃转变温度、起始晶化和峰值晶化温度都表现出对加热速率强的依赖性。基于Oawza方法可以确定非晶合金的起始晶化和峰值晶化激活能。Vogel-Fulcher-Tamman公式分析表明:含Sb元素的非晶合金具有更高的强度系数和更长的延迟时间。采用电化学极化和失重测试方法研究2种玻璃合金的腐蚀行为。与基体非晶合金相比,添加微量Sb降低了非晶合金的在含Cl-的碱性溶液中的钝化电流密度和腐蚀速率,表现出相比基体合金更为优越的耐蚀性。最后基于"点缺陷模型"进一步分析微量Sb元素对基体合金耐蚀性能的影响机理。     

Mg-Cu-Y合金非晶形成能力及热稳定性分析

利用单辊甩带法快速凝固技术制备Mg65Cu25Y10合金非晶薄带,采用X射线衍射仪、差示扫描量热仪对非晶薄带的玻璃形成能力及其热稳定性进行了分析,通过Kissinger法和Ozawa法计算了Mg65Cu25Y10非晶合金的表观激活能。结果表明,Mg65Cu25Y10非晶合金具有较强的玻璃形成能力,其过冷液相区宽度值在42⁵6 K之间,约化玻璃转变温度为0.52。Mg65Cu25Y10非晶合金的热稳定性较高,其玻璃转变激活能和起始晶化激活能分别为352.0、137.5 kJ/mol,两个晶化峰值激活能分别为61.2 kJ/mol和81.4 kJ/mol。Mg65Cu25Y10非晶合金的玻璃化转变和晶化均具有动力学效应,随着升温速率提高,非晶合金的特征转变温度向高温区移动。     

Mg-Cu-Y合金非晶形成能力及热稳定性分析

利用单辊甩带法快速凝固技术制备Mg65Cu25Y10合金非晶薄带,采用X射线衍射仪、差示扫描量热仪对非晶薄带的玻璃形成能力及其热稳定性进行了分析,通过Kissinger法和Ozawa法计算了Mg65Cu25Y10非晶合金的表观激活能。结果表明,Mg65Cu25Y10非晶合金具有较强的玻璃形成能力,其过冷液相区宽度值在42~56 K之间,约化玻璃转变温度为0.52。Mg65Cu25Y10非晶合金的热稳定性较高,其玻璃转变激活能和起始晶化激活能分别为352.0、137.5 kJ/mol,两个晶化峰值激活能分别为61.2 kJ/mol和81.4 kJ/mol。Mg65Cu25Y10非晶合金的玻璃化转变和晶化均具有动力学效应,随着升温速率提高,非晶合金的特征转变温度向高温区移动。     

Cu44.25Ag14.75Zr36Ti5非晶合金的晶化行为

采用铜模铸造法制备了直径为3mm的柱状Cu44.25Ag14.75Zr36Ti5块体非晶合金,X射线衍射证明试样为完全非晶态。利用差示扫描热分析仪(DSC)、X射线衍射,研究了该非晶合金的晶化行为。利用Kissinger和Ozawa方程求得Cu44.25Ag14.75Zr36Ti5第一晶化峰和第二晶化峰的晶化激活能。结果表明,该大块非晶合金具有良好的热稳定性,在10K/min的加热速率下,析出相主要是Cu8Zr3和Cu10Zr7。     

Fe41Co7Cr15Mo14Y2C15B6大块非晶合金的变温晶化动力学研究

采用差热分析法(DTA)研究了具有高玻璃形成能力的Fe41Co7Cr15Mo14Y2C15B6块体非晶合金的变温晶化动力学.由热分析曲线得到玻璃转变温度Tg、晶化起始温度Tx和晶化峰值温度Tp1、Tp2,这些特征温度具有明显的动力学效应.运用Kissinger法和Ozawa法分别计算出不同升温速率下该Fe基块体非晶合金的玻璃转变激活能Eg、晶化激活能Ex与激活能Ep1、Ep2.采用Kissinger方法和Ozawa方法解释了此大块非晶合金具有高的热稳定性的热力学机制.     

X-ray diffraction study of Ba0.985Na0.015Ti0.985Nb0.015O3, Ba0.6Na0.4Ti0.6Nb0.4O3 and Ba0.3Na0.7Ti0.3Nb0.7O3 compositions

The Ba_0.985Na_0.015Ti_0.985Nb_0.015O₃, Ba_0.6Na_0.4Ti_0.6Nb_0.4O₃ and Ba_0.3Na_0.7Ti_0.3Nb_0.7O₃ compositions of the (1 − x) BaTiO₃–xNaNbO₃ (BTNNx) system have been studied by X-ray diffraction and by measurements of dielectric properties. The specimens with composition BTNN (x = 0.015, 0.40 and 0.70) have been refined by the JANA program from X-ray powder diffraction data. Ceramic samples with composition (1 − x) BaTiO₃ + xNaNbO₃ (where x = 0.015, 0.40 and 0.70) were prepared by calcinations from appropriate mixture of BaCO₃, TiO₂, Na₂CO₃ and Nb₂O₅. The calcined powder was sintered at temperature range 1200–1400 °C. As the composition x increased from 0.015 (and 0.70), the ferroelectric ceramics (x = 0.015, FE) with tetragonal phase changed to the ferroelectric relaxors (RFE, x = 0.40). RFE ceramics showed a peculiar diffuse phase transition and dielectric relaxation at the low temperature (down to 180 K) due to a frustration between RFE and FE state. These ceramics present the classical ferroelectric character when 0 ≤ x < 0.075 and 0.55 < x ≤ 1 and relaxor character when 0.075 ≤ x ≤ 0.55.     

Magnetic, electrical and plastic properties of Fe76Nb2Si13B9, Fe75Ag1Nb2Si13B9 and Fe75Cu1Nb2Si13B9 amorphous alloys

Influence of 1 h annealing in vacuum on magnetic, electrical and plastic properties of Fe₇₆Nb₂Si₁₃B₉, Fe₇₅Ag₁Nb₂Si₁₃B₉ and Fe₇₅Cu₁Nb₂Si₁₃B₉ melt spun ribbons were carefully investigated. It was shown that in all cases soft magnetic properties can be significantly enhanced by applying 1-h annealing at characteristic temperatures T_op. This optimization annealing causes that permeability increases more than 15-times and magnetic losses (tangent of loss angle) achieves a minimum in relation to the as quenched state. Using structural examinations (X-ray and HRTEM) it was shown that for the Fe₇₅Cu₁Nb₂Si₁₃B₉ alloy the optimized microstructure corresponds to a nanocrystalline αFe(Si) phase whereas in other alloys to a relaxed amorphous phase free of iron nanograins. As a consequence of this fact the Fe₇₆Nb₂Si₁₃B₉ and Fe₇₅Ag₁Nb₂Si₁₃B₉ alloys show higher plasticity in comparison to the nanocrystalline Fe₇₅Cu₁Nb₂Si₁₃B₉ alloy. Temperatures of the first stage of crystallization, and related diffusion parameters were determined using measurements of resistivity versus temperature with different heating rates.     

Fe2+-Ni2+-NH3-NH4+-C2O42-H2O体系的沉淀配合平衡热力学

针对草酸盐配位共沉淀热分解还原法制备超细铁镍合金粉过程中Fe2+-Ni2+-NH3-NH4+-C2O42--H2O体系的溶液平衡建立热力学分析模型,并根据模型进行相关计算,揭示反应体系中各物质随pH值、氨及草酸浓度的变化关系。结果表明:溶液中的Fe主要以[Fe(C2O4)n]2 2n络合物形式存在,而铁氨络合物含量很低。当氨含量较低时,溶液中的Ni主要以[Ni(C2O4)n]2 2n存在;氨含量较高时,在酸性条件下,溶液中的Ni主要以[Ni(C2O4)n]2 2n存在,在碱性条件下,则主要以[Ni(NH3)n]2+存在。低pH值下,Ni的沉淀率较Fe的高,而高pH值下,Ni的沉淀率则较Fe的低。     

Thermodynamics and phase diagrams in the binary systems Na2O-SiO2, Na2O-GeO2, Na2O-B2O3, Li2O-B2O3, CaO-B2O3, SrO-B2O3, and BaO-B2O3

We applied our model to the enthalpy of mixing data of the binary systems Na₂O-SiO₂, Na₂O-GeO₂, Na₂O-B₂O₃, Li₂O-B₂O₃, CaO-B₂O₃, SrO-B₂O₃, and BaO-B₂O₃. The most stable composition in the liquid, that is where the enthalpy of mixing is most negative, is with a metal-oxygen ratio of 4 to 3, for monovalent metals (Na and Li) and 3 to 4 for divalent metals (Ba and Ca) in liquid silicates or borates. The same applies to the CaO-SiO₂, CaO-Al₂O₃, PbO-B₂O₃, PbO-SiO₂, ZnO-B₂O₃, and ZnO-SiO₂ systems. The oxygen to metal ratio, its constant value in various types of systems, reflects and describes the structure of the liquid. Using the analyzed enthalpies of mixing data and the available phase diagrams, we calculated the enthalpies of formation of the various binary compounds. The results are in excellent agreement with data in the literature that were obtained from direct solid-solid calorimetry.     

New Zr6CoAs2-type compounds: Y6CoBi2, Ho6CoBi2 and Tm6CoBi2

Results of a powder X-ray diffraction investigation of new ternary compounds are reported. The compounds Y₆CoBi₂ [a=0.8312(1) nm, c=0.4144(1) nm], Ho₆CoBi₂ [a=0.8246(2) nm, c=0.4095(1) nm], and Tm₆CoBi₂ [a=0.8155(2) nm, c=0.4066(1) nm] crystallize in the hexagonal Zr₆CoAs₂-type structure (space group P6b2m No. 189). The Zr₆CoAs₂-type structure is a superstructure of the Fe₂P-type structure.     

Al2O3-Sm2O3-CeO2电解质的性能（英文）

采用溶胶-凝胶法和低温燃烧技术制备Ce1-xSmxO2（x=0,0.1,0.2,0.3）和掺杂Sm和（2%-8%）Al2O3的二氧化铈;研究其合成、结构、致密化、导电性和热膨胀等性能,并利用XRD研究其结构和相组成。结果表明,于1300°C烧结球团,获得致密的陶瓷,于1250°C在Ce0.8Sm0.2O0.2中加入2%和4%的Al2O3以促进烧结。利用扫描电子显微镜观察烧结后球团的表面形貌,使用双探针交流阻抗谱研究总离子电导率。     

Zur Kenntnis von RbBa3Ca4Cu3V7O28

Single crystals of RbBa₃Ca₄Cu₃V₇O₂₈ were prepared above the melting point of the reaction mixture. It crystallizes with hexagonal symmetry, space group C_6V⁴-P6₃mc, a 11.1751, c 12.434 Å, Z = 2. RbBa₃Ca₄Cu₃V₇O₂₈ is the second member of a new structure type of the copper-oxovanadates. Ba²⁺ shows an unusual 12-fold coordination. The two calcium positions are coordinated by trigonal prisms and octahedra respectively. The copper coordination is characterized by a stretched square pyramid. The Cu²⁺ ions are outside the centre nearly in plane of the pyramids.

Zusammenfassung

Einkristalle von RbBa₃Ca₄Cu₃V₇O₂₈ wurden oberhalb des Schmelzpunktes der Reaktionsmischung erhalten. Die Verbindung kristallisiert hexagonal, Raumgruppe C_6V⁴-P6₃mc, a 11.1751, c 12.434 Å, Z = 2. RbBa₃Ca₄Cu₃V₇O₂₈ ist das zweite Beispiel für einen neuen Strukturtyp der Kupfer-Oxovanadate, mit 12-fach koordinierten Ba²⁺ -Ionen. Die zwei Calciumpositionen sind trigonal prismatisch bzw. oktaedrisch koordiniert. Die Koordination der Cu²⁺-Ionen ist durch eine gestreckte Pyramide charakterisiert. Cu²⁺ ist auβerhalb des Polyederzentrums nahezu in der quadratischen Fläche der Pyramide angeordnet.     

电弧喷涂制备Fe65Cr20Mo7B3.5SiMn1.5W3涂层

在Q235低碳钢板上利用电弧喷涂工艺进行喷涂,以制得Fe65Cr20Mo7B3.5SiMn1.5W3涂层。喷涂材料为自行配制的丝材,按照35%的填充率将配好的粉填充到U型不锈钢外皮中,经过多道拉拔、挤压工艺制成Φ2mm的粉芯丝材。采用X射线衍射仪、扫描电镜、能谱分析仪、透射电镜对涂层的物相和组织形貌及成分进行了表征;采用差示扫描量热仪、显微硬度仪等设备对涂层的热稳定性及显微硬度进行了检测和分析。试验结果表明:涂层组织形貌呈典型的层状组织结构,由变形良好的带状粒子相互搭接堆积而成。涂层含有50.63%的非晶相,同时含有纳米级的晶相。涂层组织均匀、结构致密、孔隙率低,并且涂层硬度高达1040.5HV0.3,属硬质涂层,具有良好的热稳定性。     

Synthesis and electrochemical properties of LiNi0.4Mn1.5Cr0.1O4 and Li4Ti5O12

Spinel compound LiNi_0.4Mn_1.5Cr_0.1O₄ (LNMCO) and Li₄Ti₅O₁₂ (LTO) were synthesized by the sol-gel method and the solid-state method, respectively. The particle sizes of the products LiNi_0.4Mn_1.5Cr_0.1O₄ and Li₄Ti₅O₁₂ were 0.5 to 2 um and 0.5 to 0.8 um, respectively. All samples exhibited excellent electrochemical properties. A LiNi_0.4Mn_1.5Cr_0.1O₄/Li₄Ti₅O₁₂ (LNMCO/LTO) cell was fabricated and was demonstrated to exhibit good electrochemical properties at the high current rate of 1 C. When the specific capacity was determined based on the mass of the LNMCO cathode, the LNMCO/LTO cell delivered 125 mAh g⁻¹ at 1 C and 77 mAh g⁻¹ at 5 C. The capacity retentions after 30 cycles were 94.4 % and 83.1 %, respectively.