Co Nanoislands Rooted on Co–N–C Nanosheets as Efficient Oxygen Electrocatalyst for Zn–Air Batteries

Developing non‐precious‐metal bifunctional oxygen reduction and evolution reaction (ORR/OER) catalysts is a major task for promoting the reaction efficiency of Zn–air batteries. Co‐based catalysts have been regarded as promising ORR and OER catalysts owing to the multivalence characteristic of cobalt element. Herein, the synthesis of Co nanoislands rooted on Co–N–C nanosheets supported by carbon felts (Co/Co–N–C) is reported. Co nanosheets rooted on the carbon felt derived from electrodeposition are applied as the self‐template and cobalt source. The synergistic effect of metal Co islands with OER activity and Co–N–C nanosheets with superior ORR performance leads to good bifuctional catalytic performances. Wavelet transform extended X‐ray absorption fine spectroscopy and X‐ray photoelectron spectroscopy certify the formation of Co (mainly Co⁰) and the Co–N–C (mainly Co²⁺ and Co³⁺) structure. As the air‐cathode, the assembled aqueous Zn–air battery exhibits a small charge–discharge voltage gap (0.82 V@10 mA cm^?2) and high power density of 132 mW cm^?2, outperforming the commercial Pt/C catalyst. Additionally, the cable flexible rechargeable Zn–air battery exhibits excellent bendable and durability. Density functional theory calculation is combined with operando X‐ray absorption spectroscopy to further elucidate the active sites of oxygen reactions at the Co/Co–N–C cathode in Zn–air battery.     

Simultaneously Integrating Single Atomic Cobalt Sites and Co9S8 Nanoparticles into Hollow Carbon Nanotubes as Trifunctional Electrocatalysts for Zn–Air Batteries to Drive Water Splitting

The development of rechargeable metal–air batteries and water electrolyzers are highly constrained by electrocatalysts for the oxygen reduction reaction (ORR), oxygen evolution reaction (OER), and hydrogen evolution reaction (HER). However, the construction of efficient trifunctional electrocatalysts for ORR/OER/HER are highly desirable yet challenging. Herein, hollow carbon nanotubes integrated single cobalt atoms with Co₉S₈ nanoparticles (CoSA + Co₉S₈/HCNT) are fabricated by a straightforward in situ self‐sacrificing strategy. The structure of the CoSA + Co₉S₈/HCNT are verified by X‐ray absorption spectroscopy and aberration‐corrected scanning transmission electron microscopy. Theoretical calculations and experimental results embrace the synergistic effects between Co₉S₈ nanoparticles and single cobalt atoms through optimizing the electronic configuration of the CoN₄ active sites to lower the reaction barrier and facilitating the ORR, OER, and HER simultaneously. Consequently, rechargeable liquid and all‐solid‐state flexible Zn–air batteries based on CoSA + Co₉S₈/HCNT exhibit remarkable stability and excellent power density of 177.33 and 51.85 mW cm^?2, respectively, better than Pt/C + RuO₂ counterparts. Moreover, the as‐fabricated Zn–air batteries can drive an overall water splitting device assembled with CoSA + Co₉S₈/HCNT and achieve a current density of 10 mA cm^?2 at a low voltage of 1.59 V, also superior to Pt/C + RuO₂. Therefore, this work presents a promising approach to an efficient trifunctional electrocatalyst toward practical applications.     

Metal–Organic‐Framework‐Derived Hybrid Carbon Nanocages as a Bifunctional Electrocatalyst for Oxygen Reduction and Evolution

The oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) are cornerstone reactions for many renewable energy technologies. Developing cheap yet durable substitutes of precious‐metal catalysts, especially the bifunctional electrocatalysts with high activity for both ORR and OER reactions and their streamlined coupling process, are highly desirable to reduce the processing cost and complexity of renewable energy systems. Here, a facile strategy is reported for synthesizing double‐shelled hybrid nanocages with outer shells of Co‐N‐doped graphitic carbon (Co‐NGC) and inner shells of N‐doped microporous carbon (NC) by templating against core–shell metal–organic frameworks. The double‐shelled NC@Co‐NGC nanocages well integrate the high activity of Co‐NGC shells into the robust NC hollow framework with enhanced diffusion kinetics, exhibiting superior electrocatalytic properties to Pt and RuO₂ as a bifunctional electrocatalyst for ORR and OER, and hold a promise as efficient air electrode catalysts in Zn–air batteries. First‐principles calculations reveal that the high catalytic activities of Co‐NGC shells are due to the synergistic electron transfer and redistribution between the Co nanoparticles, the graphitic carbon, and the doped N species. Strong yet favorable adsorption of an OOH* intermediate on the high density of uncoordinated hollow‐site C atoms with respect to the Co lattice in the Co‐NGC structure is a vital rate‐determining step to achieve excellent bifunctional electrocatalytic activity.     

Efficient Bifunctional Catalytic Electrodes with Uniformly Distributed NiN2 Active Sites and Channels for Long‐Lasting Rechargeable Zinc–Air Batteries

Freestanding bifunctional electrodes with outstanding oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) properties are of great significance for zinc–air batteries, attributed to the avoided use of organic binder and strong adhesion with substrates. Herein, a strategy is developed to fabricate freestanding bifunctional electrodes from the predeposited nickel nanoparticles (Ni‐NCNT) on carbon fiber paper. The steric effect of monodispersed SiO₂ nanospheres limits the configuration of carbon atoms forming 3D interconnected nanotubes with uniformly distributed NiN₂ active sites. The bifunctional electrodes (Ni‐NCNT) demonstrate ideal ORR and OER properties. The zinc–air batteries assembled with Ni‐NCNT directly exhibit extremely outstanding long term stability (2250 cycles with 10 mA cm^?2 charge/discharge current density) along with high power density of 120 mV cm^?2 and specific capacity of 834.1 mA h g^?1. This work provides a new view to optimize the distribution of active sites and the electrode structure.     

Nitrogen‐Doped Co3O4 Mesoporous Nanowire Arrays as an Additive‐Free Air‐Cathode for Flexible Solid‐State Zinc–Air Batteries

The kinetically sluggish rate of oxygen reduction reaction (ORR) on the cathode side is one of the main bottlenecks of zinc‐air batteries (ZABs), and thus the search for an efficient and cost‐effective catalyst for ORR is highly pursued. Co₃O₄ has received ever‐growing interest as a promising ORR catalyst due to the unique advantages of low‐cost, earth abundance and decent catalytic activity. However, owing to the poor conductivity as a result of its semiconducting nature, the ORR activity of the Co₃O₄ catalyst is still far below the expectation. Herein, we report a controllable N‐doping strategy to significantly improve the catalytic activity of Co₃O₄ for ORR and demonstrate these N doped Co₃O₄ nanowires as an additive‐free air‐cathode for flexible solid‐state zinc‐air batteries. The results of experiments and DFT calculations reveal that the catalytic activity is promoted by the N dopant through a combined set of factors, including enhanced electronic conductivity, increased O₂ adsorption strength and improved reaction kinetics. Finally, the assembly of all‐solid‐state ZABs based on the optimized cathode exhibit a high volumetric capacity of 98.1 mAh cm^‐3 and outstanding flexibility. The demonstration of such flexible ZABs provides valuable insights that point the way to the redesign of emerging portable electronics.     

Ultrafine Co3O4 Nanoparticles within Nitrogen‐Doped Carbon Matrix Derived from Metal–Organic Complex for Boosting Lithium Storage and Oxygen Evolution Reaction

Transition metal oxides have recently received great attention for application in advanced lithium‐ion batteries (LIBs) and oxygen evolution reaction (OER). Herein, the ethylenediaminetetraacetic cobalt complex as a precursor to synthesize ultrafine Co₃O₄ nanoparticles encapsulated into a nitrogen‐doped carbon matrix (NC) composites is presented. The as‐prepared Co₃O₄/NC‐350 obtained by pyrolysis at 350 °C demonstrates superior rate performance (372 mAh g^?1 at 5.0 A g^?1) and high cycling stability (92% capacity retention after 300 cycles at 1.0 A g^?1) as anode for LIBs. When evaluated as an electrocatalyst for OER, the Co₃O₄/NC‐350 achieves an overpotential of 298 mV at a current density of 10 mA cm^?2. The NC‐encapsualted porous hierarchical structure assures fast and continuous electron transportation, high activity sites, and strong structural integrity. This works offers novel complex precursors for synthesizing transition metal–based electrodes for boosting electrochemical energy conversion and storage.     

Elucidation of Active Sites on S,N Codoped Carbon Cubes Embedding Co–Fe Carbides toward Reversible Oxygen Conversion in High‐Performance Zinc–Air Batteries

The development of high‐performance but low‐cost catalysts for the electrochemical oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) is of central importance for realizing the prevailing application of metal–air batteries. Herein a facile route is devised to synthesize S, N codoped carbon cubes embedding Co–Fe carbides by pyrolyzing the Co–Fe Prussian blue analogues (PBA) coated with methionine. Via the strong metal–sulfur interaction, the methionine coating provides a robust sheath to restrain the cubic morphology of PBA upon pyrolysis, which is proved highly beneficial for promoting the specific surface area and active sites exposure, leading to remarkable bifunctionality of ORR and OER comparable to the benchmarks of Pt/C and RuO₂. Further elaborative investigations on the activity origin and postelectrolytic composition unravel that for ORR the high activity is mainly contributed by the S, N codoped carbon shell with the inactive carbide phase converting into carbonate hydroxides. For OER, the embedded Co–Fe carbides transform in situ into layered (hydr)oxides, serving as the actual active sites for promoting water oxidation. Zn–air batteries employing the developed hollow structure as the air cathode catalyst demonstrate superb rechargeability, energy efficiency, as well as portability.     

Bifunctional Transition Metal Hydroxysulfides: Room‐Temperature Sulfurization and Their Applications in Zn–Air Batteries

Bifunctional electrocatalysis for oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) constitutes the bottleneck of various sustainable energy devices and systems like rechargeable metal–air batteries. Emerging catalyst materials are strongly requested toward superior electrocatalytic activities and practical applications. In this study, transition metal hydroxysulfides are presented as bifunctional OER/ORR electrocatalysts for Zn–air batteries. By simply immersing Co‐based hydroxide precursor into solution with high‐concentration S^2?, transition metal hydroxides convert to hydroxysulfides with excellent morphology preservation at room temperature. The as‐obtained Co‐based metal hydroxysulfides are with high intrinsic reactivity and electrical conductivity. The electron structure of the active sites is adjusted by anion modulation. The potential for 10 mA cm^?2 OER current density is 1.588 V versus reversible hydrogen electrode (RHE), and the ORR half‐wave potential is 0.721 V versus RHE, with a potential gap of 0.867 V for bifunctional oxygen electrocatalysis. The Co₃FeS_1.5(OH)₆ hydroxysulfides are employed in the air electrode for a rechargeable Zn–air battery with a small overpotential of 0.86 V at 20.0 mA cm^?2, a high specific capacity of 898 mAh g^?1, and a long cycling life, which is much better than Pt and Ir‐based electrocatalyst in Zn–air batteries.     

Colloidal Cobalt Phosphide Nanocrystals as Trifunctional Electrocatalysts for Overall Water Splitting Powered by a Zinc–Air Battery

Highly efficient and stable electrocatalysts, particularly those that are capable of multifunctionality in the same electrolyte, are in high demand for the hydrogen evolution reaction (HER), oxygen evolution reaction (OER), and oxygen reduction reaction (ORR). In this work, highly monodisperse CoP and Co₂P nanocrystals (NCs) are synthesized using a robust solution‐phase method. The highly exposed (211) crystal plane and abundant surface phosphide atoms make the CoP NCs efficient catalysts toward ORR and HER, while metal‐rich Co₂P NCs show higher OER performance owing to easier formation of plentiful Co₂P@COOH heterojunctions. Density functional theory calculation results indicate that the desorption of OH* from cobalt sites is the rate‐limiting step for both CoP and Co₂P in ORR and that the high content of phosphide can lower the reaction barrier. A water electrolyzer constructed with a CoP NC cathode and a Co₂P NC anode can achieve a current density of 10 mA cm^?2 at 1.56 V, comparable even to the noble metal‐based Pt/C and RuO₂/C pair. Furthermore, the CoP NCs are employed as an air cathode in a primary zinc–air battery, exhibiting a high power density of 62 mW cm^?2 and good stability.     

One‐Step Route Synthesized Co2P/Ru/N‐Doped Carbon Nanotube Hybrids as Bifunctional Electrocatalysts for High‐Performance Li–O2 Batteries

The large‐scale commercial application of lithium–oxygen batteries (LOBs) is overwhelmed by the sluggish kinetics of oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) associated with insoluble and insulated Li₂O₂. Herein, an elaborate design on a highly catalytic LOBs cathode constructed by N‐doped carbon nanotubes (CNT) with in situ encapsulated Co₂P and Ru nanoparticles is reported. The homogeneously dispersed Co₂P and Ru catalysts can effectively modulate the formation and decomposition behavior of Li₂O₂ during discharge/charge processes, ameliorating the electronically insulating property of Li₂O₂ and constructing a homogenous low‐impedance Li₂O₂/catalyst interface. Compared with Co/CNT and Ru/CNT electrodes, the Co₂P/Ru/CNT electrode delivers much higher oxygen reduction triggering onset potential and higher ORR and OER peak current and integral areas, showing greatly improved ORR/OER kinetics due to the synergistic effects of Co₂P and Ru. Li–O₂ cells based on the Ru/Co₂P/CNT electrode demonstrate improved ORR/OER overpotential of 0.75 V, excellent rate capability of 12 800 mAh g^?1 at 1 A g^?1, and superior cycle stability for more than 185 cycles under a restricted capacity of 1000 mAh g^?1 at 100 mA g^?1. This work paves an exciting avenue for the design and construction of bifunctional catalytic cathodes by coupling metal phosphides with other active components in LOBs.     

Novel MOF‐Derived Co@N‐C Bifunctional Catalysts for Highly Efficient Zn–Air Batteries and Water Splitting

Metal–organic frameworks (MOFs) and MOF‐derived materials have recently attracted considerable interest as alternatives to noble‐metal electrocatalysts. Herein, the rational design and synthesis of a new class of Co@N‐C materials (C‐MOF‐C2‐T) from a pair of enantiotopic chiral 3D MOFs by pyrolysis at temperature T is reported. The newly developed C‐MOF‐C2‐900 with a unique 3D hierarchical rodlike structure, consisting of homogeneously distributed cobalt nanoparticles encapsulated by partially graphitized N‐doped carbon rings along the rod length, exhibits higher electrocatalytic activities for oxygen reduction and oxygen evolution reactions (ORR and OER) than that of commercial Pt/C and RuO₂, respectively. Primary Zn–air batteries based on C‐MOF‐900 for the oxygen reduction reaction (ORR) operated at a discharge potential of 1.30 V with a specific capacity of 741 mA h g_Zn^–1 under 10 mA cm^–2. Rechargeable Zn–air batteries based on C‐MOF‐C2‐900 as an ORR and OER bifunctional catalyst exhibit initial charge and discharge potentials at 1.81 and 1.28 V (2 mA cm^–2), along with an excellent cycling stability with no increase in polarization even after 120 h – outperform their counterparts based on noble‐metal‐based air electrodes. The resultant rechargeable Zn–air batteries are used to efficiently power electrochemical water‐splitting systems, demonstrating promising potential as integrated green energy systems for practical applications.     

Crosslinked Carbon Nanotube Aerogel Films Decorated with Cobalt Oxides for Flexible Rechargeable Zn–Air Batteries

Air electrodes with high catalytic activity are of great importance for rechargeable zinc–air batteries. Herein, a flexible, binder‐free composite air electrode for zinc–air batteries is reported, which utilizes a lightweight, conductive, and crosslinked aerogel film of carbon nanotubes (CNTs) functioned as a 3D catalyst‐supporting scaffold for bifunctional cobalt (II/III) oxides and as a current collector. The composite electrode shows high catalytic activities for both oxygen reduction reaction and oxygen evolution reaction, resulting from the synergistic effect of nitrogen‐doped CNTs and spinel Co₃O₄ nanoparticles. Solid‐state Zn–air batteries assembled using such free‐standing air electrodes (without the need of additional current collectors) are bendable and show low resistances, low charge/discharge overpotentials, and a high cyclic stability.     

Ultrathin Cobalt Oxide Layers as Electrocatalysts for High‐Performance Flexible Zn–Air Batteries

Synergistic improvements in the electrical conductivity and catalytic activity for the oxygen reduction reaction (ORR)/oxygen evolution reaction (OER) are of paramount importance for rechargeable metal–air batteries. In this study, one‐nanometer‐scale ultrathin cobalt oxide (CoO_x) layers are fabricated on a conducting substrate (i.e., a metallic Co/N‐doped graphene substrate) to achieve superior bifunctional activity in both the ORR and OER and ultrahigh output power for flexible Zn–air batteries. Specifically, at the atomic scale, the ultrathin CoO_x layers effectively accelerate electron conduction and provide abundant active sites. X‐ray absorption spectroscopy reveals that the metallic Co/N‐doped graphene substrate contributes to electron transfer toward the ultrathin CoO_x layer, which is beneficial for the electrocatalytic process. The as‐obtained electrocatalyst exhibits ultrahigh electrochemical activity with a positive half‐wave potential of 0.896 V for ORR and a low overpotential of 370 mV at 10 mA cm^?2 for OER. The flexible Zn–air battery built with this catalyst exhibits an ultrahigh specific power of 300 W g_cat ^?1, which is essential for portable devices. This work provides a new design pathway for electrocatalysts for high‐performance rechargeable metal–air battery systems.     

Atomically Thin Mesoporous Co3O4 Layers Strongly Coupled with N‐rGO Nanosheets as High‐Performance Bifunctional Catalysts for 1D Knittable Zinc–Air Batteries

Under development for next‐generation wearable electronics are flexible, knittable, and wearable energy‐storage devices with high energy density that can be integrated into textiles. Herein, knittable fiber‐shaped zinc–air batteries with high volumetric energy density (36.1 mWh cm^?3) are fabricated via a facile and continuous method with low‐cost materials. Furthermore, a high‐yield method is developed to prepare the key component of the fiber‐shaped zinc–air battery, i.e., a bifunctional catalyst composed of atomically thin layer‐by‐layer mesoporous Co₃O₄/nitrogen‐doped reduced graphene oxide (N‐rGO) nanosheets. Benefiting from the high surface area, mesoporous structure, and strong synergetic effect between the Co₃O₄ and N‐rGO nanosheets, the bifunctional catalyst exhibits high activity and superior durability for oxygen reduction and evolution reactions. Compared to a fiber‐shaped zinc–air battery using state‐of‐the‐art Pt/C + RuO₂ catalysts, the battery based on these Co₃O₄/N‐rGO nanosheets demonstrates enhanced and stable electrochemical performance, even under severe deformation. Such batteries, for the first time, can be successfully knitted into clothes without short circuits under external forces and can power various electronic devices and even charge a cellphone.     

In Situ Exfoliated,Edge‐Rich,Oxygen‐Functionalized Graphene from Carbon Fibers for Oxygen Electrocatalysis

Metal‐free electrocatalysts have been extensively developed to replace noble metal Pt and RuO₂ catalysts for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) in fuel cells or metal–air batteries. These electrocatalysts are usually deposited on a 3D conductive support (e.g., carbon paper or carbon cloth (CC)) to facilitate mass and electron transport. For practical applications, it is desirable to create in situ catalysts on the carbon fiber support to simplify the fabrication process for catalytic electrodes. In this study, the first example of in situ exfoliated, edge‐rich, oxygen‐functionalized graphene on the surface of carbon fibers using Ar plasma treatment is successfully prepared. Compared to pristine CC, the plasma‐etched carbon cloth (P‐CC) has a higher specific surface area and an increased number of active sites for OER and ORR. P‐CC also displays good intrinsic electron conductivity and excellent mass transport. Theoretical studies show that P‐CC has a low overpotential that is comparable to Pt‐based catalysts, as a result of both defects and oxygen doping. This study provides a simple and effective approach for producing highly active in situ catalysts on a carbon support for OER and ORR.     

Non‐3d Metal Modulation of a 2D Ni–Co Heterostructure Array as Multifunctional Electrocatalyst for Portable Overall Water Splitting

Portable water splitting devices driven by rechargeable metal–air batteries or solar cells are promising, however, their scalable usages are still hindered by lack of suitable multifunctional electrocatalysts. Here, a highly efficient multifunctional electrocatalyst is demonstrated, i.e., 2D nanosheet array of Mo‐doped NiCo₂O₄/Co_5.47N heterostructure deposited on nickel foam (Mo‐NiCo₂O₄/Co_5.47N/NF). The successful doping of non‐3d high‐valence metal into a heterostructured nanosheet array, which is directly grown on a conductive substrate endows the resultant catalyst with balanced electronic structure, highly exposed active sites, and binder‐free electrode architecture. As a result, the Mo‐NiCo₂O₄/Co_5.47N/NF exhibits remarkable catalytic activity toward the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER), affording high current densities of 50 mA cm^?2 at low overpotentials of 310 mV for OER, and 170 mV for HER, respectively. Moreover, a low voltage of 1.56 V is achieved for the Mo‐NiCo₂O₄/Co_5.47N/NF‐based water splitting cell to reach 10 mA cm^?2. More importantly, a portable overall water splitting device is demonstrated through the integration of a water‐splitting cell and two Zn–air batteries (open‐circuit voltage of 1.43 V), which are all fabricated based on Mo‐NiCo₂O₄/Co_5.47N/NF, demonstrating a low‐cost way to generate fuel energy. This work offers an effective strategy to develop high‐performance metal‐doped heterostructured electrode.     

Design and Synthesis of Spherical Multicomponent Aggregates Composed of Core–Shell,Yolk–Shell,and Hollow Nanospheres and Their Lithium‐Ion Storage Performances

Micrometer‐sized spherical aggregates of Sn and Co components containing core–shell, yolk–shell, hollow nanospheres are synthesized by applying nanoscale Kirkendall diffusion in the large‐scale spray drying process. The Sn₂Co₃–Co₃SnC_0.7–C composite microspheres uniformly dispersed with Sn₂Co₃–Co₃SnC_0.7 mixed nanocrystals are formed by the first‐step reduction of spray‐dried precursor powders at 900 °C. The second‐step oxidation process transforms the Sn₂Co₃–Co₃SnC_0.7–C composite into the porous microsphere composed of Sn–Sn₂Co₃@CoSnO₃–Co₃O₄ core–shell, Sn–Sn₂Co₃@CoSnO₃–Co₃O₄ yolk–shell, and CoSnO₃–Co₃O₄ hollow nanospheres at 300, 400, and 500 °C, respectively. The discharge capacity of the microspheres with Sn–Sn₂Co₃@CoSnO₃–Co₃O₄ core–shell, Sn‐Sn₂Co₃@CoSnO₃–Co₃O₄ yolk–shell, and CoSnO₃–Co₃O₄ hollow nanospheres for the 200^th cycle at a current density of 1 A g^?1 is 1265, 987, and 569 mA h g^?1, respectively. The ultrafine primary nanoparticles with a core–shell structure improve the structural stability of the porous‐structured microspheres during repeated lithium insertion and desertion processes. The porous Sn–Sn₂Co₃@CoSnO₃–Co₃O₄ microspheres with core–shell primary nanoparticles show excellent cycling and rate performances as anode materials for lithium‐ion batteries.     

Interfacing Manganese Oxide and Cobalt in Porous Graphitic Carbon Polyhedrons Boosts Oxygen Electrocatalysis for Zn–Air Batteries

Rational design and synthesis of highly active and robust bifunctional non‐noble electrocatalysts for both oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) are urgently required for efficient rechargeable metal–air batteries. Herein, abundant MnO/Co heterointerfaces are engineered in porous graphitic carbon (MnO/Co/PGC) polyhedrons via a facile hydrothermal‐calcination route with a bimetal–organic framework as the precursor. The in situ generated Co nanocrystals not only create well‐defined heterointerfaces with high conductivity to overcome the poor OER activity but also promote the formation of robust graphitic carbon. Owing to the desired composition and formation of the heterostructures, the resulting MnO/Co/PGC exhibits superior activity and stability toward both OER and ORR, which makes it an efficient air cathode for the rechargeable Zn–air battery. Importantly, the homemade Zn–air battery is able to deliver excellent performance including a peak power density of 172 mW cm^?2 and a specific capacity of 872 mAh g^?1, as well as excellent cycling stability (350 cycles), outperforming commercial mixed Pt/C||RuO₂ catalysts. This work highlights the synergy from heterointerfaces in oxygen electrocatalysis, thus providing a promising approach for advanced metal–air cathode materials.     

Boosting Bifunctional Oxygen Electrocatalysis with 3D Graphene Aerogel‐Supported Ni/MnO Particles

Electrocatalysts for oxygen‐reduction and oxygen‐evolution reactions (ORR and OER) are crucial for metal–air batteries, where more costly Pt‐ and Ir/Ru‐based materials are the benchmark catalysts for ORR and OER, respectively. Herein, for the first time Ni is combined with MnO species, and a 3D porous graphene aerogel‐supported Ni/MnO (Ni–MnO/rGO aerogel) bifunctional catalyst is prepared via a facile and scalable hydrogel route. The synthetic strategy depends on the formation of a graphene oxide (GO) crosslinked poly(vinyl alcohol) hydrogel that allows for the efficient capture of highly active Ni/MnO particles after pyrolysis. Remarkably, the resulting Ni–MnO/rGO aerogels exhibit superior bifunctional catalytic performance for both ORR and OER in an alkaline electrolyte, which can compete with the previously reported bifunctional electrocatalysts. The MnO mainly contributes to the high activity for the ORR, while metallic Ni is responsible for the excellent OER activity. Moreover, such bifunctional catalyst can endow the homemade Zn–air battery with better power density, specific capacity, and cycling stability than mixed Pt/C + RuO₂ catalysts, demonstrating its potential feasibility in practical application of rechargeable metal–air batteries.