BaFe<Subscript>12</Subscript>O<Subscript>19</Subscript> films produced from BaFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/α-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> heterostructures

BaFe₁₂O₁₉ hexaferrite films have been produced on thermally oxidized single-crystal silicon (SiO₂/Si) substrates by sequential ion-beam sputtering of BaFe₂O₄ and α-Fe₂O₃ targets in an argon-oxygen atmosphere. Their crystal structure has been studied, and the origin of the impurity phases forming during heat treatment has been identified. The results show that heat treatment may lead to the formation of eutectic melts. As a result, the hexaferrite films may contain spherulites.     

Variable—Range hopping in Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-K<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript> glasses

The dc conductivity of the glasses in the Fe₂O₃-Bi₂O₃-K₂B₄O₇ system was studied at temperatures between 223 and 393 K. At temperatures from 300 to 223 K, T^–1/4 (T is temperature) dependence of the conductivity was found, however, both Mott variable-range hopping and Greaves intermediate range hopping models are found to be applicable. Mott and Greaves parameters analysis gave the density of states at Fermi level N (E_F) = 3.13 × 10²⁰–21.01 × 10²⁰ and 1.93 × 10²¹–16.39 × 10²¹ cm^–3eV^–1 at 240 K, respectively. The variable-range hopping conduction occurred in the temperature range T = 300–223 K, since W_D was found to be large (W_D = 0.08–0.14 eV for these glasses) and dominated the conduction at T < 300 K.     

Crystal Structure of Uranyl Malonate Trihydrate [UO<Subscript>2</Subscript>(OOC)<Subscript>2</Subscript>CH<Subscript>2</Subscript>(H<Subscript>2</Subscript>O)]·2H<Subscript>2</Subscript>O

Single crystals of [UO₂(OOC)₂CH₂(H₂O)]·2H₂O (I) were prepared by recrystallization of finely crystalline uranyl malonate trihydrate under hydrothermal conditions. The crystal structure of I consists of electroneutral [UO₂(OOC)₂CH₂(H₂O)]_n layers and water molecules located between them. The uranium coordination number is 7. The uranium coordination polyhedron is a distorted pentagonal bipyramid with the oxygen atoms of the uranyl group in the apices. The equatorial plane is occupied by four O atoms of three malonate ligands and the water molecule. The malonate anion is coordinated in the bidentate fashion to one uranyl ion to form a six-membered ring and in the monodentate fashion to two other uranyl ions.     

Catalytic combustion of methane over Pt and PdO-supported CeO<Subscript>2</Subscript>–ZrO<Subscript>2</Subscript>–Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Catalytic combustion of methane was investigated on Pt and PdO-supported CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalysts prepared by a wet impregnation method in the presence of polyvinylpyrrolidone. The catalysts were characterized by X-ray fluorescence analysis, X-ray powder diffraction, X-ray photoelectron spectra, transmission electron microscopy, and BET specific surface area measurements. The Pt/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ and PdO/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalysts were selective for the total oxidation of methane into carbon dioxide and steam, and no by-products such as HCHO, CO, and H₂ were obtained. The catalytic activities of the PdO/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalysts were relatively higher than those of the Pt-supported catalysts, due to the facile re-oxidation of metallic Pd into PdO based on lattice oxygen supplied from the CeO₂–ZrO₂–Bi₂O₃ bulk. A decrease in the calcination temperature during the preparation process was found to be effective in enhancing the specific surface area of the catalysts, whereby particle agglomeration was inhibited. Optimization of the PdO amount and calcination temperature enabled complete oxidation of methane at temperatures as low as 320 °C on the 11.6 wt% PdO/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalyst prepared at 400 °C.     

Crystal structure of a Np(V) sesquioxalate,Na<Subscript>4</Subscript>(NpO<Subscript>2</Subscript>)<Subscript>2</Subscript>(C<Subscript>2</Subscript>O<Subscript>4</Subscript>)<Subscript>3</Subscript>·2H<Subscript>2</Subscript>O

The crystal structure of a previously unknown Np(V) sesquioxalate, Na₄(NpO₂)₂(C₂O₄)₃·2H₂O was studied. The crystal structure consists of neptunyl(V) cations, sodium cations, oxalate anions, and water molecules of crystallization. Neptunyl(V) cations and oxalate ions form anionic chains [(NpO₂)₂(C₂O₄)₃] _n ^4n? . The coordination polyhedron (CP) of Np (pentagonal bipyramid) contains two apical “yl” oxygen atoms and five equatorial O atoms of three oxalate ions. The CP of Na(1) and Na(2) cations are combined through the common edges into zigzag chains in the [010] direction. Two independent oxalate ions are tridentate and tetradentate ligands.     

Phase equilibria in the system “CaAl<Subscript>2</Subscript>Si<Subscript>3</Subscript>O<Subscript>10</Subscript>”-Na<Subscript>2</Subscript>Al<Subscript>2</Subscript>Si<Subscript>3</Subscript>O<Subscript>10</Subscript>-H<Subscript>2</Subscript>O

The phase equilibria in the “CaAl₂Si₃O₁₀”-Na₂Al₂Si₃O₁₀-H₂O system are analyzed using structural and thermal analysis data, and the ideal gonnardite structure is modeled. The results suggest that, to ensure a better correlation with the structures of the zeolites in this series, a new structural model of the gonnardite-based solid solution must be selected, with the structure rotated through 45° about the c axis in the ab plane.     

Investigation of solid solution of ZrP<Subscript>2</Subscript>O<Subscript>7</Subscript>–Sr<Subscript>2</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript>

In this study, ZrP₂O₇ was synthesized by the solid state reaction of ZrO₂ and NH₄H₂PO₄ at 900 °C. Then, in set 1; 10, 5, 1, 0.5, 0.1, 0.05, 0.03% previously prepared Sr₂P₂O₇ were doped into ZrP₂O₇, and Sr₂P₂O₇ slightly affect the unit cell parameter of cubic ZrP₂O₇ (a = 8.248(6)–8.233(8) Å). The reverse of this process was also applied to Sr₂P₂O₇ system (set 2). ZrP₂O₇ changes the unit cell parameters of orthorhombic Sr₂P₂O₇ in between a = 8.909(5)–8.877(5) Å, b = 13.163(3)–13.12(1) Å, and c = 5.403(2)–5.386(4) Å. Analysis of the vibrations of the P₂O ₇ ^4? ion and approximate band assignments for IR and Raman spectra are also reported in this work. Some coincidences in infrared and Raman spectra both sets were found and strong P–O–P bands were observed. Surface morphology, EDX analysis, and thermoluminescence properties of both sets were given the first time in this paper.     

Kinetics of Thermal Transformation of Mg<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript> · 8H<Subscript>2</Subscript>O to Mg<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>

The kinetics of thermal dehydration of Mg₃(PO₄)₂ · 8H₂O was investigated using thermogravimetry at four different heating rates. The activation energies of the dehydration step of Mg₃(PO₄)₂ · 8H₂O were calculated through the isoconversional Ozawa and Kissinger-Akahira-Sunose (KAS) methods and iterative methods, which were found to be consistent and indicate a single mechanism. The possible conversion function of the dehydration reaction for Mg₃(PO₄)₂ · 8H₂O has been estimated through the Coats and Redfern integral equation, and a better kinetic model such as random nucleation of the “Avrami–Erofeev equation (A _3/2 model)” was found. The thermodynamic functions (ΔH*, ΔG*, and ΔS*) of the dehydration reaction are calculated by the activated complex theory and indicate that it is a non-spontaneous process when the introduction of heat is not connected.     

System ZnO ⋅ B<Subscript>2</Subscript>O<Subscript>3</Subscript>-CuO ⋅ B<Subscript>2</Subscript>O<Subscript>3</Subscript>

Differential thermal analysis and x-ray diffraction data indicate that the ZnO B₂O₃-CuO B₂O₃ join of the ternary system CuO-B₂O₃-ZnO is pseudobinary, with eutectic phase relations and a liquid-liquid miscibility gap in the composition range 25–35 mol % CuO.Translated from Neorganicheskie Materialy, Vol. 41, No. 3, 2005, pp. 339–340.Original Russian Text Copyright © 2005 by Kasumova, Bananyarly.This revised version was published online in April 2005 with a corrected cover date.This revised version was published online in April 2005 with a corrected cover date.     

Evaluation of CaO–SiO<Subscript>2</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–Na<Subscript>2</Subscript>O–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> bioglass-ceramics for hyperthermia application

Magnetic bioglass ceramics (MBC) are being considered for use as thermoseeds in hyperthermia treatment of cancer. While the bioactivity in MBCs is attributed to the formation of the bone minerals such as crystalline apatite, wollastonite, etc. in a physiological environment, the magnetic property arises from the magnetite [Fe₃O₄] present in these implant materials. A new set of bioglasses with compositions 41CaO · (52 ? x)SiO₂ · 4P₂O₅  · xFe₂O₃ · 3Na₂O (2 ≤ x ≤ 10 mol% Fe₂O₃) have been prepared by melt quenching method. The as-quenched glasses were then heat treated at 1050°C for 3 h to obtain the glass-ceramics. The structure and microstructure of the samples were characterized using X-ray diffraction and microscopy techniques. X-ray diffraction data revealed the presence of magnetite in the heat treated samples with x ≥ 2 mol% Fe₂O₃. Room temperature magnetic property of the heat treated samples was investigated using a Vibrating Sample Magnetometer. Field scans up to 20 kOe revealed that the glass ceramic samples had a high saturation magnetization and low coercivity. Room temperature hysteresis cycles were also recorded at 500 Oe to ascertain the magnetic properties at clinically amenable field strengths. The area under the magnetic hysteresis loop is a measure of the heat generated by the MBC. The coercivity of the samples is another important factor for hyperthermia applications. The area under the loop increases with an increase in Fe₂O₃ molar concentration and the. coercivity decreases with an increase in Fe₂O₃ molar concentration The evolution of magnetic properties in these MBCs as a function of Fe₂O₃ molar concentration is discussed and correlated with the amount of magnetite present in them.     

Crystallization and microstructural evolution of MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript>–TiO<Subscript>2</Subscript>–La<Subscript>2</Subscript>O<Subscript>3</Subscript> glass-ceramics

Crystallization and microstructure of glasses with the molar compositions 1MgO·1.2Al₂O₃·2.8SiO₂·1.2TiO₂·xLa₂O₃ (x = 0.1 and 0.4) were thermally treated at different temperatures in the range from 950 to 1250 °C and then analyzed by X-ray diffraction and scanning electron microscopy, in combination with energy-dispersive X-ray spectroscopy and electron backscatter diffraction. It was found that the microstructure is first homogeneous with the precipitation of randomly distributed crystals and then indialite domains with embedded perrierite and rutile crystals are formed. For higher temperatures or prolonged times, more domains appear and expand into the bulk of the sample. Finally, the entire sample consists of the indialite domains and the boundaries that are enriched in rutile, perrierite, and magnesium aluminotitanate. Nevertheless, very distinct differences are observed between the samples with different La₂O₃ concentrations. For the sample with x = 0.4, the domains were detected at lower temperatures, while the quantity and size of the domains increase faster due to the promoted precipitation of indialite. For the sample with x = 0.1, in addition to the domain boundaries, secondary boundaries between the “regions” (assemblages of the domains) are observed in a larger length scale. The average size of the crystalline phases found between the “regions” is larger than that typically observed at the domain boundaries. The sizes of the crystals at the boundaries decrease with higher concentrations of La₂O₃, and the crystals (especially perrierite) within the domains become larger, resulting in a more homogeneous microstructure. This results in better dielectric properties, i.e., much higher quality factor for the sample with x = 0.4 in comparison to that with x = 0.1 after heat-treatment at 1150 or 1250 °C.     

Fabrication of Yb<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–SiO<Subscript>2</Subscript> Optical Fibers with a Perfect Step-Index Profile by the MCVD Process

An all-vapor phase MCVD process has been proposed for the fabrication of fiber preforms with a Yb₂O₃–Al₂O₃–P₂O₅–SiO₂ multicomponent glass core. We have investigated the tubular preform collapse into a rod and demonstrated approaches capable of preventing P₂O₅ losses in the central part of the core during the collapse process. Preforms with a flat, perfect step-index profile have been fabricated.     

Spectroscopic characterisation of local structure in Y<Subscript>2</Subscript>O<Subscript>3</Subscript>–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses doped with gadolinium

Gadolinium doped bismuth borate glasses containing up to 30 mol% Y₂O₃ were prepared by fast melt quenching method. The effect of yttrium on the local order in 3B₂O₃ · Bi₂O₃ and B₂O₃ · Bi₂O₃ glass matrices, particularly on the bismuth sites, was investigated by infrared (IR) spectroscopy and electron paramagnetic resonance (EPR) of Gd³⁺ ions. The IR results show that the local structure is more ordered in the glass system with higher bismuth content and the progressive addition of yttrium increases the local disorder in both bismuth–borate glass matrices. The EPR results indicate that Gd³⁺ ions occupy both bismuth and yttrium sites and reflect the same structural disorder like that suggested by IR results.     

Synthesis of thorn-like Ca<Subscript>2</Subscript>B<Subscript>2</Subscript>O<Subscript>5</Subscript>·H<Subscript>2</Subscript>O by hydrothermal method

Thorn-like polycrystalline Ca₂B₂O₅·H₂O microspheres with nano-sized slices were synthesized using boric acid and calcium hydroxide as reactants by a facile catalyst-free hydrothermal method at low temperature. The products were characterized by means of X-ray powder diffraction (XRD) and scanning electron microscopy (SEM). The XRD pattern reveals that the Ca₂B₂O₅·H₂O is a monoclinic phase polycrystalline with cell parameters a = 0·6702, b = 0·5419 and c = 0·3558 nm. SEM also reveals that the monoclinic phase polycrystalline are thorn-like microspheres composed of many flakes with an average thickness of <100 nm. Possible reaction and growth mechanism were also discussed.     

Superconducting Bands Stabilizing Superconductivity in YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>7</Subscript> and MgB<Subscript>2</Subscript>

It is shown that the ceramic superconductor YBa₂Cu₃O₇ as well as the superconducting intermetallic compound MgB₂ possesses a narrow, partly filled “superconducting band” with Wannier functions of special symmetry in their band structures. This result corroborates previous observations about the band structures of numerous superconductors and non-superconductors showing that evidently superconductivity is always connected with such superconducting bands. These findings are interpreted in the framework of a nonadiabatic extension of the Heisenberg model. Within this new group-theoretical model of correlated systems, Cooper pairs are stabilized by a nonadiabatic mechanism of constraining forces effective in narrow superconducting bands. The formation of Cooper pairs in a superconducting band is mediated by the energetically lowest boson excitations in the considered material that carry the crystal-spin angular momentum 1⋅ℏ. These crystal-spin-1 bosons are proposed to determine whether the material is a conventional low-T _c or a high-T _c superconductor. This interpretation provides the electron–phonon mechanism that enters the BCS theory in conventional superconductors.     

A physicochemical study of the Sb<Subscript>2</Subscript>Se<Subscript>3</Subscript>–Nd<Subscript>2</Subscript>Se<Subscript>3</Subscript> system

We have studied phase relations in the Sb₂Se₃–Nd₂Se₃ system and mapped out its T–x phase diagram using differential thermal analysis, X-ray diffraction, microstructural analysis, microhardness tests, and density measurements. The system contains one compound, with the composition NdSbSe₃, which melts incongruently at 865 K and crystallizes in orthorhombic symmetry with the following lattice parameters: а = 12.77(1) Å, b = 14.08(1) Å, and c = 5.82(5) Å (Z = 8, ρ_meas = 6.20 g/cm³, ρ_x = 6.38 g/cm³). At room temperature, the Nd₂Se₃ solubility in Sb₂Se₃ is 5 mol % and the Sb₂Se₃ solubility in Nd₂Se₃ is 2.5 mol %. The Sb₂Se₃–Nd₂Se₃ system has a eutectic located at 15 mol % Nd₂Se₃, with a melting point at 755 K. The electrical conductivity and thermoelectric power of the (Sb₂Se₃)_1–x (Nd₂Se₃) _x solid solutions have been measured as functions of temperature.     

Magnetic Anomalies and Electronic Structure of Ce<Subscript>2</Subscript>Cu<Subscript>2</Subscript>Mg and Ce<Subscript>2</Subscript>Pd<Subscript>2</Subscript>Mg

The intermetallic compounds RE ₂Cu₂Mg and RE ₂Pd₂Mg (RE=La, Ce) were prepared and characterized by magnetic susceptibility and heat-capacity measurements. They crystallize with an ordered U₃Si₂ type structure (space group P4/mbm) and the cerium compounds contain stable trivalent cerium ions, which undergo antiferromagnetic ordering at ∼7.5 and ∼4 K, respectively. In high magnetic fields Ce₂Cu₂Mg exhibits spin reorientation with critical field strength of 40 kOe at 5 K. The data are compared to the non-magnetic isotypic compounds La₂ T ₂Mg (T=Cu, Ni, Pd) and to the already reported intermediate valent Ce₂Ni₂Mg.     

Microwave dielectric properties of temperature-stable (Mg<Subscript>0.95</Subscript>Co<Subscript>0.05</Subscript>)<Subscript>2</Subscript>TiO<Subscript>4</Subscript>–Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> composite ceramics for LTCC applications

In this paper, the effects of Li₂O–B₂O₃–Bi₂O₃–SiO₂ (LBBS) glass on the phase formation, sintering characteristic, the microstructure and microwave dielectric properties of temperature-stable (Mg_0.95Co_0.05)₂TiO₄–Li₂TiO₃ ceramics were investigated. (Mg_0.95Co_0.05)₂TiO₄–Li₂TiO₃ powders were obtained by using the traditional solid-state process. A small amount of LBBS doping can effectively reduce sintering temperature and promote the densification of the ceramics. X-ray diffraction analysis revealed not only the primary phase (Mg·Co)₂TiO₄ associated with Li₂TiO₃ minor phase but also a third phase (Mg·Co)TiO₃. The dielectric constant and Qf values vary with the doping amount of LBBS and sintering temperatures. With the compensation of the positive temperature coefficient (τ _f ) of Li₂TiO₃ and the negative τ _f of (Mg_0.95Co_0.05)₂TiO₄, the τ _f of the specimens fluctuates around zero. The (Mg_0.95Co_0.05)₂TiO₄ ceramic with 2.5 wt% LBBS addition and sintering at 900?°C for 4 h exhibited excellent microwave dielectric properties: ? _r ?=?19.076, Qf?=?126100 GHz, and τ _f ?=?0.98 ppm/°C.     

Crystal structure of U(VI) phthalate dihydrate [UO<Subscript>2</Subscript>(OOC)<Subscript>2</Subscript>C<Subscript>6</Subscript>H<Subscript>4</Subscript>•H<Subscript>2</Subscript>O]•H<Subscript>2</Subscript>O

Crystalline uranyl phthalate dihydrate was prepared by hydrothermal method, and its crystal structure was determined. The crystal structure consists of infinite chains [UO₂LH₂O]_n coupled in bands [(UO₂)₂L₂(H₂O)₂]_n [L = C₆H₄(COO)₂], between which water molecules of crystallization are located. The coordination polyhedron of uranium atoms is a pentagonal bipyramid with the equatorial plane formed by oxygen atoms of three phthalate ions and coordinated water molecule. The U-O bond length in the UO ₂ ²⁺ cations is 1.766 . The coordination capacity of the ligands is 4. Anions are bidentately coordinated to uranium atoms to form seven-membered rings. Being bridging ligands, phthalate ions combine the neighboring uranium atoms into chains through one carboxy group, and the chains into bands, through the other carboxy group.Translated from Radiokhimiya, Vol. 46, No. 6, 2004, pp. 513–515.Original Russian Text Copyright © 2004 by Charushnikova, Krot, Starikova.     

AC Losses in YBCO-Added Bi<Subscript>1.6</Subscript>Pb<Subscript>0.4</Subscript>Sr<Subscript>2</Subscript>Ca<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript><Emphasis Type="Italic">δ</Emphasis></Subscript> Superconductors

The effect of YBCO adding on the superconducting of BPSCCO system with nominal starting composition of (Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O _δ )_1?x(YBCO) _x with x = 0.00?0.10 was studied. The preparation methods used to prepare the samples are the conventional solid-state techniques. From the XRD data, it is observed that the percentage of the Bi-2223 phase increases and Bi-2212 decreases for addition x = 0.02–0.04, respectively. The effect of YBCO addition on the BPSCCO system also has been investigated in term of AC susceptibility study. We have studied the various applied field dependence of the AC susceptibility in polycrystalline samples. The AC susceptibility measurements in the range 0.05 to 2.00 Oe show that as the applied fields increases, the intergranular AC loss peaks move to lower temperature, and also height decreases and width increases. The effect of YBCO addition for the intergranular critical current J _cm, and the presence of weak links that coupled the superconducting grains were defined.