Effect of compatibilizer in acrylonitrile‐butadiene‐styrene toughened nylon 6 blends: Ductile–brittle transition temperature

The ductile–brittle transition temperatures were determined for compatibilized nylon 6/acrylonitrile‐butadiene‐styrene (PA6/ABS) copolymer blends. The compatibilizers used for those blends were methyl methacrylate‐co‐maleic anhydride (MMA‐MAH) and MMA‐co‐glycidyl methacrylate (MMA‐GMA). The ductile–brittle transition temperatures were found to be lower for blends compatibilized through maleate modified acrylic polymers. At room temperature, the PA6/ABS binary blend was essentially brittle whereas the ternary blends with MMA‐MAH compatibilizer were supertough and showed a ductile–brittle transition temperature at ?10°C. The blends compatibilized with maleated copolymer exhibited impact strengths of up to 800 J/m. However, the blends compatibilized with MMA‐GMA showed poor toughness at room temperature and failed in a brittle manner at subambient temperatures. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2643–2647, 2003     

Photobiodegradation of low‐density polyethylene/banana starch films

The effects of the starch content, photosensitizer content, and compatibilizer on the photobiodegradability of low‐density polyethylene (LDPE) and banana starch polymer blend films were investigated. The compatibilizer and photosensitizer used in the films were PE‐graft‐maleic anhydride (PE‐g‐MA) and benzophenone, respectively. Dried banana starch at 0–20% (w/w) of LDPE, benzophenone at 0–1% (w/w) of LDPE, and PE‐g‐MA at 10% (w/w) of banana starch were added to LDPE. The photodegradation of the blend films was performed with outdoor exposure. The progress of the photodegradation was followed by determining the carbonyl index derived from Fourier transform IR measurements and the changes in tensile properties. Biodegradation of the blend films was investigated by a soil burial test. The biodegradation process was followed by measuring the changes in the physical appearance, weight loss, and tensile properties of the films. The results showed that both photo‐ and biodegradation rates increased with increasing amounts of banana starch, whereas the tensile properties of the films decreased. The blends with higher amounts of benzophenone showed higher rates of photodegradation, although their biodegradation rates were reduced with an increase in benzophenone content. The addition of PE‐g‐MA into polymer blends led to an increase in the tensile properties whereas the photobiodegradation was slightly decreased compared to the films without PE‐g‐MA. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2725–2736, 2006     

Modification of acrylonitrile‐butadiene‐styrene terpolymer by graft copolymerization with maleic anhydride in the melt. II. Properties and phase behavior

The graft copolymerization of maleic anhydride (MAH) onto acrylonitrile‐butadiene‐styrene terpolymer (ABS) using dicumyl peroxide and benzoyl peroxide as the binary initiator and styrene as the comonomer in the molten state was described. The properties and phase morphologies of the modified products (ABS‐g‐MAH) were studied. The results indicate that the melt flow index (MFI) of ABS‐g‐MAH increases with the increase of MAH content, the initiator concentration, and the screw speed, whereas the MFI decreases with the increase of temperature. The impact strength and the percentage elongation of ABS‐g‐MAH both decreased and the tensile strength of ABS‐g‐MAH increased slightly as the grafting degree increased. The phase inversion behavior of the modified product was observed by transmission electron microscopy. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2834–2839, 2004     

Effects of ABS‐g‐MAH on mechanical properties and compatibility of ABS/PC alloy

The effects of a compatibilizer, namely, an acrylonitrile–butadiene–styrene copolymer (ABS) grafted with maleic anhydrade (MAH) (ABS‐g‐MAH), on the mechanical properties and morphology of an ABS/polycarbonate (PC) alloy were studied The results showed that a small quantity of ABS‐g‐MAH has a very good influence on the notched Izod impact strength of the ABS/PC alloy without compromising other properties such as the tensile strength, flexural strength, and Vicat softening temperature (VST). The impact strength of the ABS/PC alloy, to a great extent, depends on the loading of ABS‐g‐MAH and the degree of grafting (DG) of MAH in the ABS‐g‐MAH. DSC analysis and SEM observation confirmed that ABS‐g‐MAH could significantly improve the compatibility of the ABS/PC alloy. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 831–836, 2001     

Effect of polyethylene‐graft‐maleic anhydride as a compatibilizer on the mechanical and tribological behaviors of ultrahigh‐molecular‐weight polyethylene/copper composites

Ultrahigh‐molecular‐weight polyethylene/copper (UHMWPE/Cu) composites compatibilized with polyethylene‐graft‐maleic anhydride (PE‐g‐MAH) were prepared by compression molding. The effects of the compatibilizer on the mechanical, thermal, and tribological properties of the UHMWPE/Cu composites were investigated. These properties of the composites were evaluated at various compositions, and worn steel surfaces and composite surfaces were examined with scanning electron microscopy and X‐ray photoelectron spectroscopy. The incorporation of PE‐g‐MAH reduced the melting points of the composites and increased their crystallinity to some extent. Moreover, the inclusion of the PE‐g‐MAH compatibilizer greatly increased the tensile rupture strength and tensile modulus of the composites, and this improved the wear resistance of the composites. These improvements in the mechanical and tribological behavior of the ultrahigh‐molecular‐weight‐polyethylene‐matrix composites with the PE‐g‐MAH compatibilizer could be closely related to the enhanced crosslinking function of the composites in the presence of the compatibilizer. Moreover, the compatibilizer had an effect on the transfer and oxidation behavior of the filler Cu particulates, which could be critical to the application of metallic‐particulate‐filled polymer composites in engineering. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 948–955, 2004     

Influence of high density polyethylene‐g‐maleic anhydride on compatibility and properties of poly(butylene terephthalate)/high density polyethylene blends

Poly(butylene terephthalate)/high density polyethylene (PBT/HDPE) blends and PBT/HDPE‐grafted maleic anhydride (PBT/HDPE‐g‐MAH) blends were prepared by the reactive extrusion approach, and the effect of blend compositions on the morphologies and properties of PBT/HDPE blends and PBT/HDPE‐g‐MAH blends was studied in detail. The results showed that flexural strength, tensile strength, and notched impact strength of PBT/HDPE blends decreased with the addition of HDPE, and flexural strength and tensile strength of PBT/HDPE‐g‐MAH blends decreased, while the notched impact strength of PBT/HDPE‐g‐MAH increased with the addition of HDPE‐g‐MAH. Compared with PBT/HDPE blends, the dimension of the dispersed phase particles in PBT/HDPE‐g‐MAH blends was decreased and the interfacial adhesion was increased. On the other hand, the effects of HDPE and HDPE‐g‐MAH contents on the crystalline and the rheological properties of the blends were also investigated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 6081–6087, 2006     

Preparation and characterization of low‐density polyethylene/banana starch films containing compatibilizer and photosensitizer

Composite films containing various percentages of banana starch and low‐density polyethylene (LDPE) were prepared. The effects of the compatibilizer, banana starch content, and photosensitizer content on the thermal and tensile properties of these films were investigated. The banana starch content was varied from 5 to 20 wt % of LDPE, whereas benzophenone was added as a photosensitizer in three different amounts (0.25, 0.5, and 1 wt %) based on LDPE. In these films PE‐graft‐maleic anhydride (PE‐g‐MA) was used as a compatibilizer at 10 wt % banana starch. It was found that the thermal stability of the composite films remained unchanged with respect to the amount of banana starch and benzophenone content. The addition of banana starch had no effect on the melting temperature and degree of crystallinity of the films. Similarly, PE‐g‐MA had no effect on the melting temperature but decreased the degree of crystallinity of the LDPE phase. Benzophenone caused an increase in the melting temperature but decreased the degree of crystallinity of LDPE in the films. Increasing the amount of banana starch decreased the tensile properties of the composite films. The addition of PE‐g‐MA as a compatibilizer increased the tensile properties compared with the uncompatibilized films. However, benzophenone had no effect on the tensile properties of the blend films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2717–2724, 2006     

Reactive mixing of PET and PET/PP blends with glycidyl methacrylate–modified styrene‐b‐(ethylene‐co‐olefin) block copolymers

Styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene (SEBS) and styrene‐b‐(ethylene‐co‐propylene) (SEP, SEPSEP) block copolymers with different styrene contents and different numbers of blocks in the copolymer chain were functionalized by melt radical grafting with glycidyl methacrylate (GMA) and employed as compatibilizers for PET‐based blends. Binary blends of PET with both functionalized (SEBS‐g‐GMA, SEP‐g‐GMA, SEPSEP‐g‐GMA) and neat (SEBS, SEP, SEPSEP) copolymers (75 : 25 w/w) and ternary blends of PET and PP (75 : 25 w/w) with various amounts (2.5–10 phr) of both modified and unmodified copolymers were prepared in an internal mixer, and their properties were evaluated by SEM, DSC, melt viscosimetry, and tensile and impact tests. The roles of the chemical structure, grafting degree, and concentration of the various copolymers on blend compatibilization was investigated. The blends with the grafted copolymers showed a neat improvement of phase dispersion and interfacial adhesion compared to the blends with nonfunctionalized copolymers. The addition of grafted copolymers resulted in a marked increase in melt viscosity, which was accounted for by the occurrence of chemical reactions between the epoxide groups of GMA and the carboxyl/hydroxyl end groups of PET during melt mixing. Blends with SEPSEP‐g‐GMA and SEBS‐g‐GMA, at concentrations of 5–10 phr, showed a higher compatibilizing effect with enhanced elongation at break and impact resistance. The effectiveness of GMA‐functionalized SEBS was then compared to that of maleic anhydride–grafted SEBS. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2201–2211, 2005     

Compatibilizer in waste tire powder and low‐density polyethylene blends and the blends modified asphalt

With the increasing ratio of waste tire powder (WTP) to low‐density polyethylene (LDPE), the hardness and tensile strength of the WTP/LDPE blends decreased while the elongation at break increased. Five kinds of compatibilizers, such as maleic anhydride‐grafted polyethylene (PE‐g‐MA), maleic anhydride‐grafted ethylene‐octene copolymer (POE‐g‐MA), maleic anhydride‐grafted linear LDPE, maleic anhydride‐grafted ethylene vinyl‐acetate copolymer, and maleic anhydride‐grafted styrene‐ethylene‐butylene‐styrene, were incorporated to prepare WTP/LDPE blends, respectively. PE‐g‐MA and POE‐g‐MA reinforced the tensile stress and toughness of the blends. The toughness value of POE‐g‐MA incorporating blends was the highest, reached to 2032.3 MJ/m³, while that of the control was only 1402.9 MJ/m³. Therefore, POE‐g‐MA was selected as asphalt modifier. The toughness value reached to the highest level when the content of POE‐g‐MA was about 8%. Besides that the softening point of the modified asphalt would be higher than 60°C, whereas the content of WTP/LDPE blend was more than 5%, and the blends were mixed by stirring under the shearing speed of 3000 rpm for 20 min. Especially, when the blend content was 8.5%, the softening point arrived at 82°C, contributing to asphalt strength and elastic properties in a wide range of temperature. In addition, the swelling property of POE‐g‐MA/WTP/LDPE blend was better than that of the other compalibitizers, which indicated that POE‐g‐MA /WTP/LDPE blend was much compatible with asphalt. Also, the excellent compatibility would result in the good mechanical and processing properties of the modified asphalt. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of maleic anhydride grafted polybutadiene on the compatibility of polyamide 66/acrylonitrile‐butadiene‐styrene copolymer blend

The addition of maleic anhydride grafted polybutadiene (PB‐g‐MAH) can greatly improve the compatibility of polyamide 66 (PA66)/acrylonitrile‐butadiene‐styrene copolymer (ABS) blends. Unlike the commonly used compatibilizers in polyamide/ABS blends, PB‐g‐MAH is compatible with the ABS particles' core phase polybutadiene (PB), rather than the shell styrene‐acrylonitrile (SAN). The compatibility and interaction of the components in the blends were characterized by Fourier transform‐infrared spectra (FTIR), Molau tests, melt flow index (MFI), dynamic mechanical analyses (DMA), and scanning electron microscopic (SEM) observations. The results show that PB‐g‐MAH can react with the amino end groups in PA66 while entangle with the PB phase in ABS. In this way, the compatibilizer anchors at the interface of PA66/ABS blend. The morphology study of the fracture sections before and after tensile test reveals that the ABS particles were dispersed uniformly in the PA66 matrix and the interfacial adhesion between PA66 and ABS was increased significantly. The mechanical properties of the blends thus were enhanced with the improving of the compatibility. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Toughening of recycled poly(ethylene terephthalate)/glass fiber blends with ethylene–butyl acrylate–glycidyl methacrylate copolymer and maleic anhydride grafted polyethylene–octene rubber

The aim of this study was to improve the toughness of recycled poly(ethylene terephthalate) (PET)/glass fiber (GF) blends through the addition of ethylene–butyl acrylate–glycidyl methacrylate copolymer (EBAGMA) and maleic anhydride grafted polyethylene–octene (POE‐g‐MAH) individually. The morphology and mechanical properties of the ternary blend were also examined in this study. EBAGMA was more effective in toughening recycled PET/GF blends than POE‐g‐MAH; this resulted from its better compatibility with PET and stronger fiber/matrix bonding, as indicated by scanning electron microscopy images. The PET/GF/EBAGMA ternary blend had improved impact strength and well‐balanced mechanical properties at a loading of 8 wt % EBAGMA. The addition of POE‐g‐MAH weakened the fiber/matrix bonding due to more POE‐g‐MAH coated on the GF, which led to weakened impact strength, tensile strength, and flexural modulus. According to dynamic rheometer testing, the use of both EBAGMA and POE‐g‐MAH remarkably increased the melt storage modulus and dynamic viscosity. Differential scanning calorimetry analysis showed that the addition of EBAGMA lowered the crystallization rate of the PET/GF blend, whereas POE‐g‐MAH increased it. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Dynamically cured polypropylene/Novolac blends compatibilized with maleic anhydride‐g‐polypropylene

In this article, the dynamic vulcanization process was applied to polypropylene (PP)/Novolac blends compatibilized with maleic anhydride‐grafted PP (MAH‐g‐PP). The influences of dynamic cure, content of MAH‐g‐PP, Novolac, and curing agent on mechanical properties of the PP/Novolac blends were investigated. The results showed that the dynamically cured PP/MAH‐g‐PP/Novolac blend had the best mechanical properties among all PP/Novolac blends. The dynamic cure of Novolac improved the modulus and stiffness of the PP/Novolac blends. The addition of MAH‐g‐PP into dynamically cured PP/Novolac blend further enhanced the mechanical properties. With increasing Novolac content, tensile strength, flexural modulus, and flexural strength increased significantly, while the elongation at break dramatically deceased. Those blends with hexamethylenetetramine (HMTA) as a curing agent had good mechanical properties at HMTA content of 10 wt %. Scanning electron microscopy (SEM) analysis showed that dynamically cured PP/MAH‐g‐PP/Novolac blends had finer domains than the PP/MAH‐g‐PP/Novolac blends. Thermogravimetric analysis (TGA) results indicated that the incorporation of Novolac into PP could improve the thermal stability of PP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Effects of glycerol and PE‐g‐MA on morphology,thermal and tensile properties of LDPE and rice starch blends

The effects of glycerol and polyethylene‐grafted maleic anhydride (PE‐g‐MA) on the morphology, thermal properties, and tensile properties of low‐density polyethylene (LDPE) and rice starch blends were studied by scanning electron microscopy (SEM), differential scanning calorimetry, and the Instron Universal Testing Machine, respectively. Blends of LDPE/rice starch, LDPE/rice starch/glycerol, and LDPE/rice starch/glycerol/PE‐g‐MA with different starch contents were prepared by using a laboratory scale twin‐screw extruder. The distribution of rice starch in LDPE matrix became homogenous after the addition of glycerol. The interfacial adhesion between rice starch and LDPE was improved by the addition of PE‐g‐MA as demonstrated by SEM. The crystallization temperatures of LDPE/rice starch/glycerol blends and LDPE/rice starch/glycerol/PE‐g‐MA blends were similar to that of pure LDPE but higher than that of LDPE/rice starch blends. Both the tensile strength and the elongation at break followed the order of rice starch/LDPE/glycerol/PE‐g‐MA blends > rice starch/LDPE/glycerol > LDPE/rice starch blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 344–350, 2004     

Study on toughening effect of maleic anhydride‐grafted‐poly(ethylene‐octene) to EVOH and their compatibility

Blends of poly(ethylene‐co‐vinyl alcohol) (EVOH) with maleic anhydride‐grafted‐poly(ethylene‐octene) (POE‐g‐MAH) were prepared by blending extrusion in order to improve the toughness and flexibility of EVOH. The compatibility behavior of these blends with POE‐g‐MAH content range from 0 to 25 wt% was studied using mechanical, thermal, infrared, and morphology characterization techniques. The mechanical test results showed that POE‐g‐MAH can significantly improve the impact toughness of EVOH with a brittle‐tough transition appeared at the POE‐g‐MAH content of 20 wt%. A huge increase of toughness of the blend was also observed when the POE‐g‐MAH content was increased to 15 wt%. The thermal analysis of the blends demonstrated that the thermal stability of EVOH is improved with the addition of POE‐g‐MAH, adding 20 wt% or more POE‐g‐MAH can effectively decrease the crystallinity of EVOH and greatly improve compatibility between the two components. The existence of esterification between anhydride groups in POE‐g‐MAH and hydroxyl groups in EVOH in melt processing was confirmed using Fourier transform infrared technique. Morphology analysis of the Izod impact fractures has clearly shown the mechanisms for these blends to change from brittle to tough with increasing the POE‐g‐MAH content. POLYM. ENG. SCI., 53:2093–2101, 2013. © 2013 Society of Plastics Engineers     

Compatibilization of polypropylene/ poly(3‐hydroxybutyrate) blends

Blending polypropylene (PP) with biodegradable poly(3‐hydroxybutyrate) (PHB) can be a nice alternative to minimize the disposal problem of PP and the intrinsic brittleness that restricts PHB applications. However, to achieve acceptable engineering properties, the blend needs to be compatibilized because of the immiscibility between PP and PHB. In this work, PP/PHB blends were prepared with different types of copolymers as possible compatibilizers: poly(propylene‐g‐maleic anhydride) (PP–MAH), poly (ethylene‐co‐methyl acrylate) [P(E–MA)], poly(ethylene‐co‐glycidyl methacrylate) [P(E–GMA)], and poly(ethylene‐co‐methyl acrylate‐co‐glycidyl methacrylate) [P(E–MA–GMA)]. The effect of each copolymer on the morphology and mechanical properties of the blends was investigated. The results show that the compatibilizers efficiency decreased in this order: P(E–MA–GMA) > P(E–MA) > P(E–GMA) > PP–MAH; we explained this by taking into consideration the affinity degree of the compatibilizers with the PP matrix, the compatibilizers properties, and their ability to provide physical and/or reactive compatibilization with PHB. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Melt rheology and properties of compatibilized recycled poly(ethylene terephthalate)/(styrene‐ethylene‐ethylene‐propylene‐styrene) block copolymer blends

Blends of recycled poly(ethylene terephthalate) (R‐PET) and (styrene‐ethylene‐ethylene‐propylene‐styrene) block copolymer (SEEPS) compatibilized with (maleic anhydride)‐grafted‐styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MAH) were prepared by melt blending. The compatibilizing effects of SEBS‐g‐MAH were investigated systematically by study of the morphology, linear viscoelastic behavior, and thermal and mechanical properties of the blends. The results show that there is good agreement between the results obtained by rheological measurement and morphological analysis. The rheological test shows that the melt elasticity and melt strength of the blends increase with the addition of SEBS‐g‐MAH. The Cole‐Cole plots and van Gurp‐Palmen plots confirm the compatibilizing effect of SEBS‐g‐MAH. However, the Palierne model fails to predict the linear viscoelastic properties of the blends. The morphology observation shows that all blends exhibit a droplet‐matrix morphology. In addition, the SEEPS particle size in the (R‐PET)/SEEPS blends is significantly decreased and dispersed uniformly by the addition of SEBS‐g‐MAH. Differential scanning calorimeter analysis shows that the crystallization behavior of R‐PET is restricted by the incorporation of SEEPS, whereas the addition of SEBS‐g‐MAH improves the crystallization behavior of R‐PET compared with that of uncompatibilized (R‐PET)/SEEPS blends. The Charpy impact strength of the blends shows the highest value at SEBS‐g‐MAH content of 10%, which is about 210% higher than that of pure R‐PET. J. VINYL ADDIT. TECHNOL., 22:342–349, 2016. © 2014 Society of Plastics Engineers     

Structure and properties of polypropylene/hydrotalcite nanocomposites

This article presents the study of the modification of the particle/matrix interface region and its effects on the structure and dynamic mechanical behavior of polypropylene (PP)/hydrotalcite nanocomposites prepared by melt extrusion. The interface modification was promoted by combinying the organophillization of the hydrotalcite particles with blending the PP with a maleic anhydride‐grafted‐PP (PP‐g‐MAH) or a maleic anhydride‐grafted‐poly(styrene‐co‐ethylenebutylene‐co‐styrene) (SEBS‐g‐MAH). Sodium dodecyl sulphate was used to promote the organophillization of the hydrotalcite particles. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) showed a partially exfoliated hydrotalcite structure, with an increasing exfoliation being achieved by adding a compatibilizer and organo‐modifying the particles. Values of the Young's modulus (E), storage modulus (E′), maximum tensile strength (σ_max), neck propagation strength (σ_neck), and elongation at break (ε_b) were found to depend both on the nature of the particle matrix interface as well as on the type of compatibilizer. Also, nanocomposites prepared with the organophillized particles showed lower T_g and loss factor values. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Biodegradation of blends of polyethylene‐octene elastomer with starches by fungi

Five fungi including Aspergillus niger, Penicilium pinophilum, Chaetoomium globsum, Gliocladium virens and Aureobasium pullulans were used to investigate the biodegradation of starch‐based elastomers: polyethylene‐octene elastomer (POE)/starch and grafted POE‐g‐MAH/starch copolymer blends. The viability of the composite spore suspensions were measured before estimating the fungal growth on the surface of specimens. The weight loss, morphology and mechanical properties of the blended specimens were measured using scanning electron microscopy and a mechanical properties tester after 28 days of culturing. The spore suspension in the experiment showed good viability. Pure POE and POE‐g‐MAH did not allow significant fungal growth. Pure POE did not lose weight or have a change in tensile strength, but pure POE‐g‐MAH lost about 0.07% of its weight with a slight reduction in tensile strength during culture period. There was heavy growth on the surface of POE/starch and POE‐g‐MAH/starch blends after 28 days of culturing. The weight loss of POE/starch and POE‐g‐MAH/starch blends increased with increasing starch content. POE‐g‐MAH/starch blends tended to lose more weight than POE/starch blends. After biodegradation, the surface of POE/starch and POE‐g‐MAH/starch blends became rough with many holes and cracks, indicating that the films were eroded by the fungi. Tensile strength of POE/starch and POE‐g‐MAH/starch blends decreased after culturing because of microbial attack. On the contrary, elongation at break of POE‐g‐MAH/starch blends increased after biodegradation. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci 114:3574–3584, 2009     

Compatible thermoplastic starch/polyethylene blends by one‐step reactive extrusion

In the presence of dicumyl peroxide (DCP), the thermal plasticization of starch and its compatibilizing modification with polyethylene was accomplished by one‐step reactive extrusion in a single‐screw extruder at the same time. Because of the formation of polyethylene‐graft‐maleic anhydride (PE‐g‐MAH) during the extrusion, it was used as the compatibilizer between the thermoplastic starch and polyethylene. The blending samples were characterized by means of thermogravimetric analysis (TGA), scanning electron microscopy (SEM), dynamic thermal mechanical analysis (DTMA) and Fourier‐transform infrared (FTIR) analysis. The experimental results showed that in the presence of DCP the addition of MAH improved the mutual dispersion of molecules in thermoplastic starch and polyethylene. From TGA, we concluded that the thermal stability of the blends with MAH was improved compared with the blends without MAH. The DTMA and FTIR results indicated that, with the addition of MAH, the compatibility of molecules between thermoplastic starch and polyethylene in the blends was improved. Copyright © 2004 Society of Chemical Industry