Characterization of Hot Deformation Behavior of AMS 5708 Nickel-Based Superalloy Using Processing Map

The hot deformation behavior of AMS 5708 nickel-based superalloy was investigated by means of hot compression tests and a processing map in the temperature range of 950-1200 °C and a strain rate range of 0.01-1 s^?1 was constructed. The true stress-true strain curves showed that the maximum flow stress decreases with the increase of temperature and decrease of strain rate. The developed processing map based on experimental data, showed variations of efficiency of power dissipation relating to temperature and strain rate at constant strain. Interpretation of the processing map showed one stable domain, in which dynamic recrystallization was the dominant microstructural phenomenon, and one instability domain with flow localization. The results of interpretation of flow stress curves and processing map were verified by the microstructure observations. There are two optimum conditions for hot working of this alloy with efficiency peak of 0.36: the first is at 1150 °C for a strain rate of 1 s^?1 that produces a fine grained microstructure. The second is at 1200 °C for a strain rate of 0.01 s^?1 that produces a coarse grained microstructure.     

Hot Deformation Processing Map and Microstructural Evaluation of the Ni-Based Superalloy IN-738LC

Hot deformation behavior of the Ni-based superalloy IN-738LC was investigated by means of hot compression tests over the temperature range of 1000-1200 °C and strain rate range of 0.01-1 s^?1. The obtained peak flow stresses were related to strain rate and temperature through the hyperbolic sine equation with activation energy of 950 kJ/mol. Dynamic material model was used to obtain the processing map of IN-738LC. Analysis of the microstructure was carried out in order to study each domain’s characteristic represented by the processing map. The results showed that dynamic recrystallization occurs in the temperature range of 1150-1200 °C and strain rate of 0.1 s^?1 with the maximum power dissipation efficiency of 35%. The unstable domain was exhibited in the temperature range of 1000-1200 °C and strain rate of 1 s^?1 on the occurrence of severe deformation bands and grain boundary cracking.     

Hot Deformation Characteristics of 13Cr-4Ni Stainless Steel Using Constitutive Equation and Processing Map

Hot compression tests were performed to study the hot deformation characteristics of 13Cr-4Ni stainless steel. The tests were performed in the strain rate range of 0.001-10 s^?1 and temperature range of 900-1100 °C using Gleeble® 3800 simulator. A constitutive equation of Arrhenius type was established based on the experimental data to calculate the different material constants, and average value of apparent activation energy was found to be 444 kJ/mol. Zener-Hollomon parameter, Z, was estimated in order to characterize the flow stress behavior. Power dissipation and instability maps developed on the basis of dynamic materials model for true strain of 0.5 show optimum hot working conditions corresponding to peak efficiency range of about 28-32%. These lie in the temperature range of 950-1025 °C and corresponding strain rate range of 0.001-0.01 s^?1 and in the temperature range of 1050-1100 °C and corresponding strain rate range of 0.01-0.1 s^?1. The flow characteristics in these conditions show dynamic recrystallization behavior. The microstructures are correlated to the different stability domains indicated in the processing map.     

Hot Compression Deformation Behavior and Processing Maps of Mg-Gd-Y-Zr Alloy

Hot compression deformation behavior and processing maps of the Mg-Gd-Y-Zr alloy were investigated in this paper. Compression tests were conducted at the temperature range from 300 to 450 °C and the strain rate range from 0.001 to 1.0 s^?1. It is found that the flow stress behavior is described by the hyperbolic sine constitutive equation in which the average activation energy of 251.96 kJ/mol is calculated. Through the flow stress behavior, the processing maps are calculated and analyzed according to the dynamic materials model. In the processing maps, the variation of the efficiency of the power dissipation is plotted as a function of temperature and strain rate. The instability domains of flow behavior are identified by the maps. The maps exhibit a domain of dynamic recrystallization occurring at the temperature range of 375-450 °C and strain rate range of 0.001-0.03 s^?1 which are the optimum parameters for hot working of the alloy.     

Hot Deformation Behavior and Processing Maps of 2099 Al-Li Alloy

Hot deformation behavior and processing maps of the 2099 Al-Li alloy are investigated by tensile test at the temperature range from 250 to 450 °C and the strain rate range from 0.001 to 5.0 s^?1. The typical true stress-true strain curves show that the flow stress increases with increasing the strain rate and decreasing the deforming temperature. All curves exhibit rapid work hardening at an initial stage of strain followed by remarkable dynamic softening. Based on the flow stress behavior, the processing maps are calculated and analyzed according to the dynamic materials model (DMM). The processing maps exhibit an instability domain in the temperature and strain rate ranges: T = 250-260 °C and \(\dot{\upvarepsilon }\)  = 0.1-0.5 s^?1. The maps also exhibit an optimum hot working condition in the stability domain that occurs in the temperature of 400 °C for a strain rate of 0.001 s^?1 and having a maximum efficiency of 60%. The microstructural examinations exhibit the occurrence of dynamic recovery (DRV) during hot deformation of the 2099 alloy which is the dominant softening mechanism in the alloy. The fracture behavior changes from a brittle fracture to a ductile fracture as strain rate decreases and temperature increases.     

Optimization of thermal processing parameters of Ti555211 alloy using processing maps based on Murty criterion

Isothermal compression testing of Ti555211 titanium alloys was carried out at deformation temperatures from 750 to 950 °C in 50 °C intervals with a strain rate of0.001–1.000 s~(-1). The high-temperature deformation behavior of the Ti555211 alloy was characterized by analysis of stress–strain behavior, kinetics and processing maps. A constitutive equation was formulated to describe the flow stress as a function of deformation temperature and strain rate, and the calculated apparent activation energies are found to be 454.50 and 207.52 k J mol~(-1)in the a b-phase and b-phase regions, respectively. A processing map based on the Murty instability criterion was developed at a strain of 0.7. The maps exhibit two domains of peak efficiency from 750 to 950 °C. A *60 % peak efficiency occurs at 800–850 °C/0.001–0.010 s~(-1). The other peak efficiency of *60 % occurs at C950 °C/0.001–0.010 s~(-1), which can be considered to be the optimum condition for high-temperature working of this alloy.However, at strain rates of higher than 1.000 s~(-1)and deformation temperatures of 750 and 950 °C, clear process flow lines and bands of flow localization occur in the hightemperature deformation process, which should be avoided in Ti555211 alloy hot processing. The mechanism in stability domain and instability domain was also discussed.     

Cu-Ni-Si-P合金热变形行为及热加工图

采用高温等温压缩试验,对Cu?Ni?Si?P合金在应变速率0.01~5?1、变形温度600~800°C条件下的高温变形行为进行了研究,得出了该合金热压缩变形时的热变形激活能Q和本构方程。根据实验数据与热加工工艺参数构建了该合金的热加工图,利用热加工图对该合金在热变形过程中的热变形工艺参数进行了优化,并利用热加工图分析了该合金的高温组织变化。热变形过程中Cu?Ni?Si?P合金的流变应力随着变形温度的升高而降低,随着应变速率的提高而增大,该合金的动态再结晶温度为700°C。该合金热变形过程中的热变形激活能Q为485.6 kJ/mol。通过分析合金在应变为0.3和0.5时的热加工图得出该合金的安全加工区域的温度为750~800°C,应变速率为0.01~0.1 s?1。通过合金热变形过程中高温显微组织的观察,其组织规律很好地符合热加工图所预测的组织规律。     

Constitutive Modeling of Dynamic Recrystallization Behavior and Processing Map of 38MnVS6 Non-Quenched Steel

The dynamic recrystallization behavior of 38MnVS6 non-quenched steel was investigated by hot compression tests on a Gleeble1500 thermomechanical simulator. True stress-strain curves and deformed specimens were obtained in the temperature range of 850-1200 °C and the strain rate range of 0.01-10 s^?1. By regression analysis of the experimental results, the critical strain model and austenite grain size model for dynamic recrystallization were established as a function of Zener-Hollomon parameter. The dynamic recrystallization kinetic model for 38MnVS6 non-quenched steel was established on the basis of the modified Avrami equation. In addition, based on the dynamic material model, the processing map of the steel was established at the strain of 0.5. It was found that the unstable phenomena of the steel did not appear at the deformation conditions. The processing map exhibited a domain of complete dynamic recrystallization occurring in the temperature range of 950-1200 °C and the strain rate range of 0.01-5 s^?1, which were the optimum parameters for the hot working of the steel.     

Optimization of Hot Extrusion Process Parameters of Mg97Y2Zn1 Alloy Based on the Processing Maps

The processing maps of the Mg₉₇Y₂Zn₁ alloy have been developed for optimizing hot workability and controlling the microstructure in this paper. Compression tests were conducted in the temperature range from 250 to 450 °C and the strain rate range from 0.001 to 5.0 s^?1. The processing maps were calculated based on the flow stress behavior and analyzed according to the dynamic materials model. The maps exhibited a stability domain that occurs in the temperature of 430-450 °C for a strain rate of 0.002-0.003 s^?1 and having a maximum efficiency of 50%. A hot extrusion test was carried out to assess the prediction of the processing maps for Mg₉₇Y₂Zn₁ alloy. The influence of the extrusion temperature on the microstructure and tensile properties of the extruded alloys was analyzed to identify the optimum processing parameters. The results have shown good agreement between the regimes exhibited by the map and the microstructure of the extruded alloy.     

Characteristics of High-Temperature Deformation Behavior of Ti-45Al-2Cr-3Ta-0.5W Alloy

High-temperature deformation behavior tests of as-cast Ti-45Al-2Cr-3Ta-0.5W alloy were conducted over a wide range of strain rates (0.001-1.0 s^?1) and temperatures (1150-1300 °C). The flow curves for the current alloy exhibited sharp peaks at low strain levels, followed by pronounced work hardening and flow localization at high strain levels. Phenomenological analysis of the strain rate and temperature dependence of peak stress data yielded an average value of the strain rate sensitivity equal to 0.25 and an apparent activation energy of ~420 kJ/mol. Processing maps were established under different deformation conditions, and the optimal condition for hot work on this material was determined to be 1250 °C/0.001 s^?1. The stable deformation region was also found to decrease with increasing strain. Dynamic recrystallization (DRX) was the major softening mechanism controlling the growth of grains at the grain boundary. Meanwhile, local globularization and dynamic recovery (DR) were the main softening mechanisms in the lamellar colony. When deformed at higher temperatures (~1300 °C), the cyclic DRX and DR appeared to dominate the deformation. Moreover, the evolution of the β phase during hot deformation played an important role in the dynamic softening of the alloy.     

Constitutive analysis and processing map for hot working of a Ni-Cu alloy

The hot deformation behavior of a Ni-Cu alloy was studied using hot compression testing in the temperature range of 950 °C–1150 °C and at strain rates of 0.001 s^?1-1 s^?1. Flow curves at low strain rates, up to 0.01 s^?1, were typical of DRX characterized by a single peak, while at higher strain rates, the typical form of a DRX flow curve was not observed. The power-law constitutive equation was used to correlate flow stress to strain rate and temperature, and the apparent activation energy of hot deformation was determined to be about 462.4 kJ/mol. The peak strain and stress were related to the Zener-Hollomon parameter and the modeling formula was proposed. The dependence of flow stress to the Z changed at ln Z=38.5, which was considered to be a critical condition for the change in the mechanism of dynamic recrystallization. The efficiency of power dissipation was determined to be between 10–35 percent at different deformation conditions. According to the dynamic material model, stable flow was predicted for the studied temperature and strain rate ranges. Highly serrated grain boundaries at low strain rates were considered to be a reason for the occurrence of continuous dynamic recrystallization. On the contrary, at high strain rates, equiaxed grain structure was attributed to the typical discontinuous dynamic recrystallization.     

Processing maps for hot working of a P/M iron aluminide alloy

The hot working behavior of a Fe–24 wt.% Al iron aluminide alloy processed by the powder metallurgy route has been studied in the temperature range 750–1150°C and strain rate range 0.001–100 s⁻¹ by establishing processing maps at different strains in the range 0.1–0.5. The features in the processing maps have changed with strain suggesting that the mechanisms of hot deformation are evolving with strain. Early in the deformation (strain of 0.1), the map exhibited a single domain with a peak efficiency of power dissipation of about 44% occurring at about 1100°C and a strain rate of about 0.03 s⁻¹. This domain represents dynamic recrystallization (DRX) of the initial material possibly causing a substantial grain refinement. With increasing strain, a bifurcation has occurred giving rise to two domains: (1) at strain rates lower than about 0.1 s⁻¹ and temperatures above 1000°C, superplastic deformation has occurred, and (2) at strain rates higher than about 10 s⁻¹ and temperatures above 1125°C, DRX has occurred. The material exhibited flow localization at lower temperatures and higher strain rates. On the basis of the processing maps, the optimum processing routes available for hot working of this material are outlined.     

粗层片原始组织的TC11钛合金热变形行为及其热压缩工艺参数优化(英文)

基于粗层片原始组织的α+β型TC11钛合金的热压缩实验,研究了该合金在950~1100°C、0.001~10s1条件下的热变形行为;依据动态材料模型构建了不同应变下的加工图,并对热压缩工艺参数和变形机制分别进行优化和分析。结果表明,加工图中存在2个功率耗散效率较高区和1个功率耗散效率较低的流变失稳区。这些区域的功率耗散效率呈现出收敛或发散的特征。在α+β两相区,功率耗散效率收敛区位于950~990°C、0.001~0.01s1范围,其峰值功率耗散效率出现在950°C、0.001s1,前者和后者分别为α+β两相区较佳和最佳的热压缩工艺窗口;在β单相区,功率耗散效率收敛区位于1020~1080°C、0.001~0.1s1范围,其峰值功率耗散效率出现在1050°C、0.001~0.01s1,前者和后者分别为β相区的较佳和最佳的热压缩工艺窗口。功率耗散效率发散区位于应变速率大于0.5s1的范围内,其对应的流动失稳机制为局部流动,此时流变应力呈现出流变软化现象。在α+β两相区和β单相区优化工艺窗口内的变形机制分别为动态球化和自扩散控制的动态再结晶。优化结果与变形组织观察结果吻合良好。     

A Study on the Hot Deformation Behavior of Cast Mg-4Sn-2Ca (TX42) Alloy

The hot deformation behavior of as-cast Mg-4Sn-2Ca (TX42) alloy has been studied using compression tests in the temperature range of 300°C to 500°C, and strain rate range of 0.0003 s^?1 to 10 s^?1. Based on the flow stress data, a processing map has been developed, which exhibited two domains of dynamic recrystallization in the temperature and strain rate ranges: (I) 300°C to 380°C and 0.0003 s^?1 to 0.001 s^?1, and (II) 400°C to 500°C and 0.004 s^?1 to 6 s^?1. While hot working may be conducted in either of these domains, the resulting grain sizes are finer in the first domain than in the second. The apparent activation energy values estimated by kinetic analysis of the temperature and strain rate dependence of flow stress in the domains 1 and 2 are 182 kJ/mol and 179 kJ/mol, respectively. Both the values are much higher than that for self-diffusion in pure magnesium, indicating that the thermally stable CaMgSn particles in the matrix cause significant back stress during the hot deformation of this alloy. The alloy exhibits a regime of flow instability at lower temperatures and higher strain rates, which manifested as flow localization.     

Hot deformation behavior of Al–9.0Mg–0.5Mn–0.1Ti alloy based on processing maps

Hot deformation behavior of extrusion preform of the spray-formed Al–9.0Mg–0.5Mn–0.1Ti alloy was studied using hot compression tests over deformation temperature range of 300–450 °C and strain rate range of 0.01–10 s^?1. On the basis of experiments and dynamic material model, 2D processing maps and 3D power dissipation maps were developed for identification of exact instability regions and optimization of hot processing parameters. The experimental results indicated that the efficiency factor of energy dissipate (η) lowered to the minimum value when the deformation conditions located at the strain of 0.4, temperature of 300 °C and strain rate of 1 s^?1. The softening mechanism was dynamic recovery, the grain shape was mainly flat, and the portion of high angle grain boundary (>15°) was 34%. While increasing the deformation temperature to 400 °C and decreasing the strain rate to 0.1 s^?1, a maximum value of η was obtained. It can be found that the main softening mechanism was dynamic recrystallization, the structures were completely recrystallized, and the portion of high angle grain boundary accounted for 86.5%. According to 2D processing maps and 3D power dissipation maps, the optimum processing conditions for the extrusion preform of the spray-formed Al–9.0Mg–0.5Mn–0.1Ti alloy were in the deformation temperature range of 340–450 °C and the strain rate range of 0.01–0.1 s^?1 with the power dissipation efficiency range of 38%–43%.     

High temperature deformation and processing map of a NiTi intermetallic alloy

The deformation behavior of a 49.8 Ni-50.2 Ti (at pct) alloy was investigated using the hot compression test in the temperature range of 700 °C–1100 °C, and strain rate of 0.001 s^?1 to 1 s^?1. The hot tensile test of the alloy was also considered to assist explaining the related deformation mechanism within the same temperature range and the strain rate of 0.1 s^?1. The processing map of the alloy was developed to evaluate the efficiency of hot deformation and to identify the instability regions of the flow. The peak efficiency of 24–28% was achieved at temperature range of 900 °C–1000 °C, and strain rates higher than 0.01 s^?1 in the processing map. The hot ductility and the deformation efficiency of the alloy exhibit almost similar variation with temperature, showing maximum at temperature range of 900 °C–1000 °C and minimum at 700 °C and 1100 °C. Besides, the minimum hot ductility lies in the instability regions of the processing map. The peak efficiency of 28% and microstructural analysis suggests that dynamic recovery (DRV) can occur during hot working of the alloy. At strain rates higher than 0.1 s^?1, the peak efficiency domain shifts from the temperature range of 850 °C–1000 °C to lower temperature range of 800 °C–950 °C which is desirable for hot working of the NiTi alloy. The regions of flow instability have been observed at high Z values and at low temperature of 700 °C and low strain rate of 0.001 s^?1. Further instability region has been found at temperature of 1000 °C and strain rates higher than 1 s^?1 and at temperature of 1100 °C and all range of strain rates.     

Characterization of mechanisms of hot deformation of as-cast nickel aluminide alloy

The hot deformation behavior of as-cast Ni₃Al alloy has been characterized on the basis of its flow stress variation obtained by isothermal constant true strain rate compression testing in the temperature range 1100–1250°C and strain rate range 0.001–10 s⁻¹. The mechanisms of hot working have been evaluated using four generations of materials modeling techniques, which included shape of stress–strain curves, kinetic analysis, processing maps and dynamical systems approach. The material exhibited a steady-state flow behavior at slower strain rates but flow softening associated sometimes with broad oscillations, was observed at higher strain rates. The flow stress data did not obey the kinetic rate equation over the entire regime of testing but a good fit has been obtained in the intermediate range of temperatures (1150–1200°C). In this range, a stress exponent value of 6.5 and an apparent activation energy of about 750 kJ/mol have been evaluated. Microstructural investigations have shown that the matrix γ′ phase undergoes dynamic recovery in the presence of harder γ colonies The processing maps revealed four different domains out of which three are interpreted to represent cracking processes. The fourth domain, which has a peak efficiency of about 44%, occurred at 1250°C/0.001 s⁻¹. Microstructural observations revealed that this domain represents dynamic recrystallization (DRX) of γ phase and is desirable for hot working the material. The material exhibits flow instabilities when deformed in the intermediate temperature regime at strain rates higher than 1 s⁻¹ and these are manifested as shear localization.     

Research on the Hot Deformation Behavior of Al-Zn-Mg-Sc-Zr Alloy During Compression at Elevated Temperature

The flow behavior of Al-Zn-Mg-Sc-Zr alloy during hot compression deformation was studied by isothermal compression test using Gleeble-1500 thermo-mechanical equipment. Compression tests were performed in the temperature range of 340-500 °C and in the strain rate range of 0.001-10 s^?1.The results indicate that the flow stress of the alloy increases with increasing strain rate at a given temperature, and decreases with increasing temperature at a given imposed strain rate. The relationship between flow stress and strain rate and temperature was derived by analyzing the experimental data. The constitutive equation of Al-Zn-Mg-Sc-Zr alloy during hot compression deformation can be described by the Arrhenius relationship of the hyperbolic sine form. The values of A, n, and α in the analytical expression of strain rate are fitted to be 1.49 × 10¹⁰ s^?1, 7.504, and 0.0114 MPa^?1, respectively. The hot deformation activation energy of the alloy during compression is 150.25 kJ/mol. The temperature and strain rate have great influences on microstructure evolution of Al-Zn-Mg-Sc-Zr alloy during hot compression deformation. According to microstructure evolution, the dynamic flow softening is mainly caused by dynamic recovery and dynamic recrystallization in this present experiment.     

Compressive response and microstructural evolution of in-situ TiB2 particle-reinforced 7075 aluminum matrix composite

The hot forming behavior, failure mechanism, and microstructure evolution of in-situ TiB₂ particle-reinforced 7075 aluminum matrix composite were investigated by isothermal compression test under different deformation conditions of deformation temperatures of 300–450 °C and strain rates of 0.001-1 s^?1. The results demonstrate that the failure behavior of the composite exhibits both particle fracture and interface debonding at low temperature and high strain rate, and dimple rupture of the matrix at high temperature and low strain rate. Full dynamic recrystallization, which improves the composite formability, occurs under conditions of high temperature (450 °C) and low strain rate (0.001 s^?1); the grain size of the matrix after hot compression was significantly smaller than that of traditional 7075Al and ex-situ particle reinforced 7075Al matrix composite. Based on the flow stress curves, a constitutive model describing the relationship of the flow stress, true strain, strain rate and temperature was proposed. Furthermore, the processing maps based on both the dynamic material modeling (DMM) and modified DMM (MDMM) were established to analyze flow instability domain of the composite and optimize hot forming processing parameters. The optimum processing domain was determined at temperatures of 425-450 °C and strain rates of 0.001-0.01 s^?1, in which the fine grain microstructure can be gained and particle crack and interface debonding can be avoided.     

Hot deformation behavior and microstructure evolution of TC4 titanium alloy

The hot deformation behavior of Ti-6Al-4V(TC4) titanium alloy was investigated in the temperature range from 650 °C to 950 °C with the strain rate ranging from 7.7×10-4 s-1 to 7.7×10-2 s-1.The hot tension test results indicate that the flow stress decreases with increasing the deformation temperature and increases with increasing the strain rate.XRD analysis result reveals that only deformation temperature affects the phase constitution.The microstructure evolution under different deformation conditions was characterized by TEM observation.For the deformation of TC4 alloy,the work-hardening is dominant at low temperature,while the dynamic recovery and dynamic re-crystallization assisted softening is dominant at high temperature.