共查询到20条相似文献,搜索用时 125 毫秒
1.
按照矿山建井施工的惯例,明竖井施工均采用常规的有井架施工法。我们在桐柏银矿主井的施工中,利用现场的施工条件,针对主井系统及其地面配套工程部分等联锁工程在时间上的控制要求,采用了明竖井无井架的施工方法,在建井施工中进行了一次新时探索和尝试,收到了预期的效果。 一、方案选择 1.工程技术特征 依据施工图设计,主井为箕斗提升井,净径3.5米,荒径4.0米,井深210米,井口标高+245.20米,上部设计有一42米高的钢筋混凝土永久井架,并集中原矿仓、信号房等于一体。井筒在+210米处有一措施单巷已与井筒联通,并在+81.7米标高处设计有 相似文献
2.
《中国石油和化工标准与质量》2013,(13)
立井架是射孔作业施工的头道工序,井架立的标准与否直接影响整个射孔作业施工过程。同时,射孔作业各项工艺都是以井架为载体进行的,因此保证每部井架的标准安装尤为重要。为保证作业施工安全及施工质量,研制了井架校正仪,并在作业施工中进行了成功应用。 相似文献
3.
《中国石油和化工标准与质量》2013,(13)
试采大队现有北奔、解放、T815三种型号的井架车,是井下作业施工中井架背立、运输的关键设备。在多年的使用过程中,发现这三种车型的车身稳定性能都存在缺陷,特别是在地面泥泞、松软的特殊井场施工时,安全风险尤为突出。本文通过对井架车千受力情况分析,建立了井架车力矩平衡,以井架车最大倾翻角评价井架车稳定性,结合一起井架车倾倒事故,提出了增强井架车稳定性的整改措施,以便应用于生产实践中,提高背立井架施工的安全系数,保障作业生产安全有序进行。 相似文献
4.
矿山井巷施工中,以竖井的难度最大。而竖井施工又以盲竖井最为困难、复杂。因为它没有宽阔的场地,只能利用狭窄的巷道和峒室作为工业场地。因此,盲竖井施工中提绞设备的布置,需要井建工作者认真加以考虑。现以田湖铁矿梅石山盲竖井为例,介绍我们的一些做法。 梅石山矿段采用平峒盲竖井开拓,平峒口至盲竖井口距离1400米,井筒内径4.5米,井口标高228.281米,井深238米,上部为提升塔、高19.5米,采用1.85×4多绳摩擦轮提升。 由于井筒断面小,施工设备尽量简化,经反复考虑,一共需要15台绞车、稳车进行悬吊,井筒断面布置如图1所示。提绞设备见下 相似文献
5.
6.
7.
8.
在较大型的立式贮罐及塔设备的现场 ,施工单位在工程实践中创造了多种多样的组装工艺方法 ,其中内短井架倒装法 ,在施工条件差 ,尤其对于场地狭窄 ,无法使用大型吊装机械 ,以及在众多的厂房、设备空隙中间重新制造一台设备 ,显示出独特的优点 ,且施工方便 ,降低施工造价 ,因而有广泛的应用价值。1 施工原理内短井架倒法 是利用在立式容器的底板上竖立起数根长 3m左右的钢管短柱 ,组成内吊杆井架平台 ,采用手链葫芦的提升由上而下的逐节制作 ,由于采用的内平台高度只有 3m ,外焊缝操作人员在基础上站立施工 ,内焊缝操作人员在平台内施工 … 相似文献
9.
我国各类矿山有不少是用竖井开拓的,据对国内60多个矿山的统计,用竖井开拓的就占50%。实践表明:竖井工程是矿山建设中重要的连锁工程,其施工的速度与质量直接影响整个矿山建设进度与以后的投产使用。金属、化工矿山的竖井掘进,较多采用普通施工法。因此,提高竖井普通法施工速度与 相似文献
10.
结合米仓山特长公路隧道通风竖井施工,从施工工艺、施工安全保障措施、施工效果等方面介绍了竖井短段掘砌混合作业施工技术及成功经验。 相似文献
11.
12.
The stress distribution and the displacement are examined when a butt adhesive joint, in which two dissimilar tubular shafts are joined, is subjected to a torsional load. In the analyses, general representations of the stresses and the displacements are given as a torsion problem when two dissimilar tubular shafts are band-adhesively bonded. Next, in the case of shafts with the same material, effects of the ratio of the shear modulus of an adhesive to that of shafts, the thickness of the adhesive and the bonded position of band-adhesive on the stress distribution are made clear by numerical computations. Moreover, when solid shafts are joined, these effects are made clear by the similar analyses and numerical computations. 相似文献
13.
The stress distribution and the displacement are examined when a butt adhesive joint, in which two dissimilar tubular shafts are joined, is subjected to a torsional load. In the analyses, general representations of the stresses and the displacements are given as a torsion problem when two dissimilar tubular shafts are band-adhesively bonded. Next, in the case of shafts with the same material, effects of the ratio of the shear modulus of an adhesive to that of shafts, the thickness of the adhesive and the bonded position of band-adhesive on the stress distribution are made clear by numerical computations. Moreover, when solid shafts are joined, these effects are made clear by the similar analyses and numerical computations. 相似文献
14.
Stress distributions and deformation of adhesive butt joints are analyzed by an elastoplastic finite element method when the joints of similar and dissimilar shafts are subjected to external bending moments. The effects of the ratio of Young's modulus for the adherends to that for an adhesive and the effects of the adhesive thickness on the interface stress distribution are investigated. Joint strength is predicted by using the elastoplastic interface stress distributions. It is found that the singular stress at the edge of the interfaces increases with an increase of the ratio of Young's modulus. Measurement of strains in joints and experiments on joint strength were conducted. The numerical results are in fairly good agreement with the experimental results. It is observed that the joint strength for dissimilar shafts are smaller than those for similar shafts. A fracture of dissimilar adhesive up-bonded shafts occurred from the interface of the adherend with smaller Young's modulus. It is seen that joint strength increases as the adhesive thickness increases. 相似文献
15.
在掘进工作面通风系统的形成过程中,需要设计施工不同功能的通风立眼,以达到有效通风目的,解决赵庄二号井1308泄水巷正掘、反掘施工期间通风的问题。研究通风立眼快速施工工艺,对日后通风立眼、溜煤眼的施工均有积极参考价值。 相似文献
16.
结合合成氨厂的使用情况,分析钾碱泵轴腐蚀磨损严重的原因,提出采用改进设计,提高泵轴的加工和安装质量,改善操作使用条件的措施。实践证明起到了减少或防止腐蚀磨损的作用 相似文献
17.
18.
19.
介绍了电子产品中轴类零件的化学镀镍工艺。讨论了长轴、短轴和盲孔螺纹零件的化学镀镍方法,提出了提高镍镀层耐蚀性能的措施。 相似文献
20.
聚隆矿业有限公司原矿井地面工业广场压煤约200万t,为解放出老工业广场及井筒压煤,通过论证,确定在原风井附近受采空区影响区域新建立井井筒及工业广场。采空区上面快速建井技术在聚隆公司成功应用,拓宽了立井施工条件的适用范围,在条件类似的矿井具有广泛的推广应用前景。 相似文献