On Applicability of Multilayer Coated Tool in Dry Machining of Aerospace Grade Stainless Steel

The present research work has been undertaken with a view to investigate the influence of CVD multilayer coated (TiN/TiCN/Al₂O₃/ZrCN) and cutting speed on various machining characteristics such as chip morphology, tool wear, cutting temperature, and machined surface roughness during dry turning of 17-4 PH stainless steel. In order to understand the effectiveness of CVD multilayer coated tool a comparison has been carried out with that of uncoated carbide insert. The surface roughness and cutting temperature obtained during machining with chemical vapor deposition (CVD) multilayer coated tool was higher than that of uncoated carbide insert at all cutting velocity. However, the results clearly indicated that CVD multilayer coated tool played a significant role in restricting various modes of tool failure and reducing chip deformation compared to its uncoated counterpart. Adhesion and abrasion were found to be dominating wear mechanism with flank wear, plastic deformation, and catastrophic failure being major tool wear modes.     

Environment Friendly Machining of Ni–Cr–Co Based Super Alloy using Different Sustainable Techniques

In order to eradicate the use of mineral based cutting fluid, the machining of Ni–Cr–Co based Nimonic 90 alloy was conducted using environment friendly sustainable techniques. In this work, uncoated tungsten carbide inserts were employed for the machining under dry (untreated and cryogenically treated), MQL, and cryogenic cutting modes. The influence of all these techniques was examined by considering tool wear, surface finish, chip contact length, chip thickness, and chip morphology. It was found that the cryogenically treated tools outperformed the untreated tools at 40 m/min. At cutting speed of 80 m/min, MQL and direct cooling with liquid nitrogen brought down the flank wear by 50% in comparison to dry machining. Similarly at higher cutting speed, MQL and cryogenic cooling techniques provided the significant improvement in terms of nose wear, crater wear area, and chip thickness value. However, both dry and MQL modes outperformed the cryogenic cooling machining in terms of surface roughness value at all the cutting speeds. Overall cryotreated tools was able to provide satisfactory results at lower speed (40 m/min). Whereas both MQL and cryogenic cooling methods provided the significantly improved results at higher cutting speeds (60 and 80 m/min) over dry machining.     

Comparative investigation towards machinability improvement in hard turning using coated and uncoated carbide inserts: part I experimental investigation

The investigation of low cost uncoated and coated carbide insert in the hard turning of hardened AISI D2 steel (≥55 HRC) will definitely open up a new arena as an economical alternative suitable to industrial machining sectors. Thus, this paper reports the comparative machinability assessment for the hard turning of AISI D2 steel ((55 ±1) HRC) by coated and uncoated carbide insert in a dry environment. Micro hardness and abrasion tests were carried out to assess resistance capability against wear. The above test results confirmed the greater wear resistance ability of Al₂O₃ coated carbide insert over uncoated carbide. Based on the extensive investigation of comparative machinability, the coated carbide insert (TiN-TiCN-Al₂O₃) outperformed the uncoated carbide insert with regard to surface roughness, flank wear, chip-tool interface temperature, and chip morphology. Abrasion and diffusion were observed as the principal tool wear mechanisms in the investigated range. The uncoated carbide failed completely due to the severe chipping and quick dulling of the cutting edge, which led to its unsuitability for machining hardened steel. The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-018-0215-z     

Tool life and surface integrity when milling inconel 718 with coated cemented carbide tools

Abstract

This paper presents a study of tool life and surface integrity while machining superalloy Inconel 718 using coated cemented carbide tools. In the machining of heat resistant superalloys used in aeronautical applications and classified as difficult‐to‐machine, tool life is an important parameter in evaluating the performance of the cutting tools. Surface quality of the workpiece is one of the important criteria in determining tool life. Our tests have been done under various combinations of speed, feed rate, and depth of cut to verify the change in surface roughness due to increasing tool wear. The behavior of the uncoated, TiN, and TiCN layers using various cutting conditions was analyzed. At the end, a choice of coating and optimization of the cutting conditions has been proposed.     

Modelling the orthogonal machining process using coated carbide cutting tools

In this paper finite element methods were used to determine the influence of various coated and uncoated tungsten carbide cutting tools on the machining of a nickel-based super alloy Inconel 718. Disposable coated and uncoated carbide inserts were used both experimentally and as FEA models to study how the stress distribution within different coatings and carbide grades compared to each other, under a range of cutting conditions. Simulation of an orthogonal metal cutting process was performed using FORGE2, an elasto-visco plastic FEA code. All FE models were assumed to be plane strain. The results include the stress and temperature distributions through the primary shear zone, the chip/tool contact region and the coating/substrate boundaries. The tool wear and stress results from the FE modelling agree favourably with those obtained from experimental work.     

Experimental Investigation on Sialon Ceramic Inserts for Ultra-high-speed Milling of Inconel 718

A series of milling aerospace material Inconel 718 experiments were conducted with a sialon ceramic tool to investigate chip evolution, cutting force, and tool wear at different cutting speeds. Round inserts were used at ultra-high-speeds under dry cutting conditions. A scanning electron microscopy and an optical microscope were used to observe the worn surfaces and to reveal the wear mechanisms of the inserts. The experiment results showed that the macroscopic shape of the chips was small scraps and fan-shaped. With the increase in the cutting speed, the plastic deformation of the chips was increasingly serious. The minimal average cutting forces were obtained at v_c = 700 m/min. The rise of cutting temperature was resulted from the increase in cutting deformation work and friction work with cutting speed. The combined effect of thermal stress and mechanical stress contributed to the tool chipping, flaking, microcrack propagation, abrasion, and adhesion which were the primary reasons of the sialon ceramic tool wear.     

Machinability studies on 17-4 PH stainless steel under cryogenic cooling environment

Under higher cutting conditions, machining of 17-4 precipitation hardenable stainless steel (PH SS) is a difficult task due to the high cutting temperatures as well as accumulation of chips at the machining zone, which causes tool damage and impairment of machined surface finish. Cryogenic machining is an efficient, eco-friendly manufacturing process. In the current work, cutting temperature, tool wear (flank wear (V_b) and rake wear), chip morphology, and surface integrity (surface topography, surface finish (R_a), white layer thickness (WLT)) were considered as investigative machinability characteristics under the cryogenic (liquid nitrogen), minimum quantity lubrication (MQL), wet and dry environments at varying cutting velocities while machining 17-4 PH SS. The results show that the maximum cutting temperature drop found in cryogenic machining was 72%, 62%, and 61%, respectively, in contrast to dry, wet, and MQL machining conditions. Similarly, the maximum tool wear reduction was found to be 60%, 55%, and 50% in cryogenic machining over the dry, wet, and MQL machining conditions, respectively. Among all the machining environments, better surface integrity was obtained by cryogenic machining, which could produce the functionally superior products.     

Ranges of application of free-cutting steels and recommended tool materials

Abstract

Four low carbonfree-cutting steels (0·11% carbon resulphurised, 0·11% carbon leaded–resulphurised, 0·08% carbon resulphurised, and 0·15% carbon leaded) were turned, dry, with a series of six types of cutting tool in which rake angle, tool material, and coating were varied (5° rake, high speed steel, TiN coated and uncoated; 15° rake, high speed steel, TiN coated and uncoated; 5° rake, cemented carbide, TiN coated and uncoated) in order to determine the optimum tool–workpiece combination for three cutting speed ranges: a low speed range in which the built-up edge (BUE) was forming or about to form; a speed range covering the BUE regime; and a higher speed range in which the BUE became a built-up layer (BUL). Tool–workpiece interaction was assessed by measurement of cutting forces, chip form, surface finish, tool temperature, and wear. It is suggested by the results that the best combination in the low speed range is that of leaded–resulphurised steel and uncoated high speed steel. In the BUE range, the combination of leaded steels and uncoated tools should be avoided; at higher speeds, coated tools are preferred, with non-resulphurised leaded steel giving the lowest tool temperatures and highest cutting speeds before ultimate failure. These recommendations should be treated with caution and used only as guidelines.

MST/867     

Study of deformation zone effects of low,conventional, high and very high speed machining

The paper deals with cutting speed in range 3 m?min^‐1 up to 2200 m?min^‐1 and its complex impact mainly on chip macroscopic shape, chip microstructure, chip compression, tool wear, tool life and machined surface quality and interprets and compares the effects regarding low, conventional, high and very high speed machining based on the dry turning of carbon steel by sintered carbide coated by titanium nitride and ceramic cutting inserts. The deformation zone response for different cutting speeds at the tool‐chip‐workpiece interfaces and their effect on tool wear were studied. The extensive (so called complete) experiments within wide range of values and large number of measurements were carried out. The formation of secondary chip occurring in high speed turning is reported. Moreover, the paper analyses the total machining time involving tool replacement time in terms of high speed machining regarding the obtained experimental results.     

Effect of Machining Parameters on Surface Integrity in High Speed Milling of Super Alloy GH4169/Inconel 718

Control of surface integrity is a vital consideration in the machining of components subjected to fatigue loading, for example, critical components of aerospace engines. In this research, three important aspects of surface integrity of a machined part—surface roughness, micro-hardness, and residual stresses—were analyzed for their variations with the cutting parameters. Finish milling of super alloy GH4169/Inconel 718 was carried out using coated cemented carbide and whisker-reinforced coated ceramic inserts. All of the three machining parameters—cutting speed, feed rate, and depth of cut—were found to have a substantial effect on the surface integrity of the finished part. Although different cutting parameters gave different effects for the two types of cutting inserts, overall better surface integrity was obtained at minimum cutting feed and medium cutting speed and depth of cut value. Moreover, carbide inserts produced better surface integrity of the finished part, whereas ceramic inserts generated very high surface tensile stresses and poor surface finish due to back striking of the adhered metal chips.     

Cutting Performance and Wear Mechanism of Multilayer Diamond-Coated Tools

Monolayer and multilayer diamond films are deposited on WC-Co cemented carbide by hot-filament chemical vapor deposition. The growth characteristics of diamond coatings are analyzed. Cutting performance characteristics such as tool life and the stability of machining process in the machining of presintered ZrO₂ are compared based on the variation of cutting speed and resultant cutting force, and workpiece surface roughness. For the monolayer diamond coatings, as the concentration of CH₄ increases from 1% to 5%, the diamond crystal is transformed from micron columnar crystal to nanocluster crystal. The multilayer diamond coatings combine the advantages of micron- and nanocrystalline structures. The multilayer diamond-coated tool exhibits longer service life and better machining quality. Because of the appearance of the brittle–plastic conversion mechanism, the surface integrity of ZrO₂ processed by multilayer diamond-coated tool is relatively high. As for the uncoated tool, the workpiece is mainly machined by brittle spalling. The interfacial stratified fracture system between the interlayers is proposed to be the toughening mechanism of the multilayer structure.     

An experimental analysis of effective high speed turning of superalloy Inconel 718

Superalloy, Inconel 718 is widely used in the sophisticated applications due to its unique properties. However, machining of such superior material is difficult and costly due its peculiar characteristics. The present article is an attempt to suggest Taguchi optimization technique to study the machinability of Inconel 718 with respect to cutting force, cutting temperature, and tool life in high speed turning of Inconel 718 using cemented tungsten carbide (K20) cutting tool. Therefore, the objective of this work is divided into two phases: (i) to demonstrate a correlation between cutting speed, feed, and depth of cut with respect to cutting force, cutting temperature, and tool life in a process control of high speed turning of Inconel 718 in order to identify the optimum combination of cutting parameters; (ii) to show the effect of high speed cutting parameters on the tool wear mechanism and chip analysis. These correlations were obtained by multiple linear regressions. The confirmation tests were carried out to make a comparison between the experimental results and mathematical models proposed. The proposed models agree well with the experimental results.     

Experimental investigations on cryogenic cooling by liquid nitrogen in the end milling of hardened steel

Milling of hardened steel generates excessive heat during the chip formation process, which increases the temperature of cutting tool and accelerates tool wear. Application of conventional cutting fluid in milling process may not effectively control the heat generation also it has inherent health and environmental problems. To minimize health hazard and environmental problems caused by using conventional cutting fluid, a cryogenic cooling set up is developed to cool tool–chip interface using liquid nitrogen (LN₂). This paper presents results on the effect of LN₂ as a coolant on machinability of hardened AISI H13 tool steel for varying cutting speed in the range of 75–125 m/min during end milling with PVD TiAlN coated carbide inserts at a constant feed rate. The results show that machining with LN₂ lowers cutting temperature, tool flank wear, surface roughness and cutting forces as compared with dry and wet machining. With LN₂ cooling, it has been found that the cutting temperature was reduced by 57–60% and 37–42%; the tool flank wear was reduced by 29–34% and 10–12%; the surface roughness was decreased by 33–40% and 25–29% compared to dry and wet machining. The cutting forces also decreased moderately compared to dry and wet machining. This can be attributed to the fact that LN₂ machining provides better cooling and lubrication through substantial reduction in the cutting zone temperature.     

Machining studies on coated high speed steel tools

This paper reports studies on the machining of type 4340 steel heat treated to Rc 33 by high speed steel tools (type M 42) coated with TiC using the activated reactive evaporation process. The coated tools exhibited a tool life of 300–800% higher than the uncoated tools under continuous cutting conditions. The principal failure mode was flank wear. The cutting forces were measured and were found to be 50% lower for coated tools than for uncoated tools.     

Comparison between use of TiN-coated and uncoated high-speed steel and fine-grained cemented carbide tools in cutting of resulphurized 0·08 wt-%C free-cutting steel

Abstract

A free-cutting 0·08%C steel has been turned dry using uncoated fine–grained cemented carbide tools and both uncoated and TiN-coated (by chemical vapour deposition)T 42 high-speed steel tools. Temperature estimates from the high–speed steel tools show that coating reduces the maximum rake-face temperature by about 125 K over a range of cutting speeds, permitting higher cutting speeds to be used before the onset of cratering. The wear mechanisms and built-up-edge behaviour have been investigated in terms of the tool/chip interface temperature and the relative plasticity of MnS inclusions. Manganese sulphide seems to have a higher affinity for the TiN coating than for the uncoated tools, permitting easier interfacial shear, and reducing contact area and built-up-edge size. With coated tools a built-up cap of workpiece material forms over the cutting edge, protecting it from wear; as a result there is only a small initial improvement in surface finish, but since nose wear is reduced, surface finish is maintained over a longer cutting period than with uncoated tools.

MST/212     

Comparison of tool life and surface characteristics of uncoated,coated carbide and ceramic tools during machining of SiC reinforced ZA43 alloy MMC

Abstract

In the present investigation, machinability issues of zinc–aluminium (ZA43) alloy reinforced with silicon carbide particles (SiC) were evaluated. The fabrication of composite was done through liquid metallurgy technique. Metal matrix composite (MMC) was subjected to turning using conventional lathe with three grades of cutting tools, namely, uncoated carbide tool, coated carbide tool and ceramic tool. Surface roughness and tool wear were measured during the machining process. Results reveal that roughness increases with increase in the reinforcement concentration and particle size. Feed has direct influence on roughness, i.e. surface deteriorates with higher feeds. Depth of cut has very minimum effect on the surface roughness, while inverse effect of cutting speed on the roughness was observed (i.e. increase in the cutting speed leads to better finish on the specimen). Tool wear was studied during the investigation, and it was noticed that MMC with higher reinforcement concentration and particle size cause severe wear on the flank of the cutting tool. Increase in the cutting speed, feed and depth of cut also increases the flank wear on the tool. Out of all the three grades of tools, coated carbide tool outperformed uncoated carbide and ceramic tools.     

Impact of graphite particle on milling of Al/15Al2O3 and Al/15Al2O3/5Gr composites

ABSTRACT

Hybrid Metal Matrix Composites (MMCs) are a new class of composites, formed by a combination of the metal matrix and more than one type of reinforcement having different properties. Machining of MMCs is a difficult task because of its heterogeneity and abrasive nature of reinforcement, which results in excessive tool wear and inferior surface finish. This paper investigates experimentally the addition of graphite (Gr) on cutting force, surface roughness and tool wear while milling Al/15Al₂O₃ and Al/15Al₂O₃/5Gr composites at different cutting conditions using tungsten carbide (WC) and polycrystalline diamond (PCD) insert. The result reveals that feed has a major contribution on cutting force and tool wear, whereas the machined surface roughness was found to be more sensitive to speed for both composite materials. The incorporation of graphite reduces the coefficient of friction between the tool–workpiece interfaces, thereby reducing the cutting force and tool wear for hybrid composites. The surface morphology and worn tool are analyzed using scanning electron microscope (SEM). The surface damage due to machining extends up to 200 µm for Al/15Al₂O₃/5Gr composites, which is beyond 250 µm for Al/15Al₂O₃ composites.     

Cuttability Investigation of Coated Carbides

The cutting performance of CVD-Ti(C,N)/Al₂O₃(Tl), CVD-Ti(C,N)/Al₂O₃/ TiN(T2) and PVD-TiN(T3) coated inserts was investigated in the dry turning of a low alloy steel. The PVD-TiN single-layer coated insert presented a better cutting performance based on wear and material removal indices than the CVD multilayer coated inserts at low feed rate. At high feed rate, it was the CVD-Ti(C,N)/Al₂O₃ coated insert that gave the best cutting performance. While excessive nose wear and plastic deformation limited the tool lives of Tl and T2, it was chipping/fracture for T3. Cutting temperature was deduced to have more effect on chip serrations than did degree of work hardening; with PVD-TiN inducing the highest degree of work hardening and lowest cutting temperature. Microstructural evidence also suggested brittle deformation and dissolution/diffusion as the wear mechanisms on T3, and plastic deformation, interfacial, and surface fatigue cracks were the observed phenomena for Tl and T2.     

Improvement of Machinability using Laser-Aided Hybrid Machining for Inconel 718 Alloy

Hybrid machining is an emerging technique for difficult-to-cut materials to overcome the problems associated with conventional machining (CM). Inconel 718, a super alloy of nickel, is a high-temperature alloy commonly used in aircraft and thermal industries and categorized as one among the difficult-to-cut materials. In this study, the influence of cutting conditions of Inconel 718 alloy during laser-assisted hybrid machining (LAHM) is investigated and the results are compared with CM. During LAHM, the process parameters of cutting speed, feed rate, approach angle, and laser power are varied. The present work is carried out in two phases: (i) determination of effective heat-affected depth (HAD) during laser preheating (using central composite design (CCD) in response surface methodology); (ii) optimization of cutting conditions during machining (using Taguchi's method). Compared with CM, the LAHM shows the following reduction benefits: (i) 33% in feed force (Fx), 42% in thrust force (Fy), and 28% in cutting force; (ii) improved surface finish (surface roughness, Ra) of 28%; and (iii) reduction in tool wear by 50%. The chip morphology reveals the decrease in shear angle and increase in chip thickness during LAHM. No change in the hardness value of the machined surface after LAHM indicates the absence of subsurface damage.     

High-speed turning experiments on metal matrix composites

The hard abrasive ceramic component which increases the mechanical characteristics of metal matrix composites (MMC) causes quick wear and premature tool failure in the machining operations. The aim of the paper is to compare the behaviour of high rake angle carbide tools with their diamond coated versions in high-speed machining of an Al₂O₃Al 6061 MMC. The influence of the cutting parameters, in particular cutting feed and speed, on tool wear and surface finish has been investigated. The higher abrasion resistance of the coatings results in increased tool life performances and different chip formation mechanisms.