Influence of pH and bath composition on properties of Ni–Fe alloy films synthesized by electrodeposition

Fe?CNi films were electrodeposited on ITO glass substrates from the electrolytes with different molar ratio of Ni $^{\boldsymbol{2+}}$ /Fe $^{\boldsymbol{2+}}$ and different pH values (2 $\boldsymbol{\cdot}$ 1, 2 $\boldsymbol{\cdot}$ 9, 3 $\boldsymbol{\cdot}$ 7 and 4 $\boldsymbol{\cdot}$ 3) at 25 $\boldsymbol{^\circ}$ C. The properties of Fe?CNi alloy films depend on both Ni $^{\boldsymbol{2+}}$ and Fe $^{\boldsymbol{2+}}$ concentrations in electrolyte and pH values. The content of Ni increases from 38% to 84% as the mole ratio of NiSO $_{\boldsymbol{4}}$ /FeSO $_{\boldsymbol{4}}$ increasing from 0 $\boldsymbol{\cdot}$ 50/0 $\boldsymbol{\cdot}$ 50 to 0 $\boldsymbol{\cdot}$ 90/0 $\boldsymbol{\cdot}$ 10 in electrolyte and slightly decreases from 65% to 42% as the pH values increase from 2 $\boldsymbol{\cdot}$ 1 to 4 $\boldsymbol{\cdot}$ 3. The X-ray diffraction analysis reveals that the structures of the films strongly depend on the Ni content in the binary films. The magnetic performance of the films shows that the saturation magnetization ( $\boldsymbol{M}_{\boldsymbol{\rm s}})$ decreases from 1775 $\boldsymbol{\cdot}$ 01 emu/cm $^{\boldsymbol{3}}$ to 1501 $\boldsymbol{\cdot}$ 46 emu/cm $^{\boldsymbol{3}}$ with the pH value increasing from 2 $\boldsymbol{\cdot}$ 1 to 4 $\boldsymbol{\cdot}$ 3 and the saturation magnetization ( $\boldsymbol{M}_{\boldsymbol{\rm s}})$ and coercivity ( $\boldsymbol{H}_{\boldsymbol{\rm c}})$ move up from 1150 $\boldsymbol{\cdot}$ 44 emu/cm $^{\boldsymbol{3}}$ and 58 $\boldsymbol{\cdot}$ 86 Oe to 2498 $\boldsymbol{\cdot}$ 88 emu/cm $^{\boldsymbol{3}}$ and 93 $\boldsymbol{\cdot}$ 12 Oe with the increase of Ni $^{\boldsymbol{2+}}$ concentration in the electrolyte, respectively.     

Molecular beam epitaxy of semipolar AlN(11\bar{2}2) and GaN(11\bar{2}2) on m-sapphire

We report on the plasma-assisted molecular-beam epitaxy of semipolar $\hbox{AlN}(11\bar{2}2)$ and GaN( $11\bar{2}2$ ) films on $(1\bar{1}00)$ m-plane sapphire. AlN deposited on m-sapphire settles into two main crystalline orientation domains, $\hbox{AlN}(11\bar{2}2)$ and $\hbox{AlN}(10\bar{1}0),$ whose ratio depends on the III/V ratio. Growth under moderate nitrogen-rich conditions enables to isolate the $(11\bar{2}2)$ orientation. The in-plane epitaxial relationships of $\hbox{AlN}(11\bar{2}2)$ on m-plane sapphire are $[11\bar{2}\bar{3}]_{\rm AlN} \vert \vert [0001]_{\rm sapphire}$ and $[1\bar{1}00]_{\rm AlN} \vert \vert [11\bar{2}0]_{\rm sapphire}.$ GaN deposited directly on m-sapphire results in ( $11\bar{2}2$ )-oriented layers with ( $10\bar{1}\bar{3}$ )-oriented inclusions. A ～100 nm-thick AlN( $11\bar{2}2$ ) buffer imposes the ( $11\bar{2}2$ )-orientation for the GaN layer grown on top. By studying the Ga-desorption on GaN( $11\bar{2}2$ ), we conclude that these optimal growth conditions corresponds to a Ga excess of one monolayer on the GaN( $11\bar{2}2$ ) surface.     

Hypersensitive Transition of Nd(III) Complexes in Liquids Detected by Pulsed-Laser-Induced Photoacoustic Spectroscopy

Laser-induced photoacoustic (PA) spectroscopy for the spectral measurements of extremely weak absorption such as a forbidden transition of lanthanide ions in liquids has been established. In spectroscopy, a pulsed Nd:YAG laser connected with a MOPO series optical parametric oscillator which emits a broad spectrum covering UV and visible regions is used as the excitation source, and the induced PA signals are detected by an optimized PA piezoelectric transducer. The absorption spectra of trivalent lanthanide ions ( $\text{ Pr}^{3+}, \text{ Ho}^{3+}$ , and $\text{ Nd}^{3+})$ in aqueous solutions have been obtained by the detection system with a detection-limit absorbance of $1.3\times 10^{-5}\,\text{ cm}^{-1}$ at room temperature. In addition, the effects of different binding environments on the band shapes and oscillator strengths of the hypersensitive transitions of $\text{ Nd}^{3+}$ ions, i.e., $\text{ Nd}(\text{ CH}_{3}\text{ COO})_{3}$ $\cdot $ $\text{ H}_{2}\text{ O}$ dissolved in $0.1\,{\text{ mol}} \cdot \text{ l}^{-1}$ acetic acid and $\text{ Nd(3-butanedione)}_{3}{\cdot } 2\text{ H}_{2} \text{ O}$ dissolved in triglycol compared with $\text{ NdCl}_{3}$ in $0.1\,{\text{ mol}}\cdot \text{ l}^{-1}$ hydrochloric acid, are observed. The results show that the chemical environment around the lanthanide ions has great impact on 4f–4f transitions, which is rationalized as the impact in terms of ligand (or solvent) special structures and coordination properties.     

Study of Glass-Transition Kinetics of Pb-Modified Se_{80}In_{20} System by Using Non-isothermal Differential Scanning Calorimetry

Glass-transition kinetics of $\mathrm{Se}_{80}\mathrm{In}_{20-\mathrm{x}}\mathrm{Pb}_{\mathrm{x}}$ ( $x =$ 0, 5, 10, and 15) chalcogenide glasses have been carried out at different heating rates by using differential scanning calorimeter (DSC) under the non-isothermal condition. The glass-transition temperature $T_{\mathrm{g}}$ and peak glass-transition temperature $T_{\mathrm{pg}}$ have been determined from DSC thermograms. The reduced glass temperature $T_{\mathrm{rg}}$ , total relaxation time $\tau _{T_{g}}$ thermal-stability parameters $K^{l}$ and $S$ , the activation energy of glass transition $E_{\mathrm{g}}$ , the fragility index $F_{\mathrm{i}}$ , and the average coordination number $\langle Z\rangle $ have been calculated on the basis of the experimental results. The temperature differences $(T_{\mathrm{c}}-T_{\mathrm{g}}), K_{\mathrm{gl}}, K^{l}, S$ , and $E_{\mathrm{g}}$ are found to be maxima for $\mathrm{Se}_{80}\mathrm{In}_{10}\mathrm{Pb}_{10}$ glass. This indicates that $\mathrm{Se}_{80}\mathrm{In}_{10}\mathrm{Pb}_{10}$ glass has the highest thermal stability and glass-forming ability in the investigated compositional range. These results could be explained on the basis of modification of the chemical bond formation due to incorporation of Pb in the Se–In glassy matrix.     

Specific Heat of K_{0.71}Na_{0.29}Fe_2As_2 at Very Low Temperatures

A commercially available calorimeter has been used to investigate the specific heat of a high-quality K $_{0.71}$ Na $_{0.29}$ Fe $_2$ As $_2$ single crystal. The addenda heat capacity of the calorimeter is determined in the temperature range $0.02 \, \mathrm{K} \le T \le 0.54 \, \mathrm{K}$ . The data of the K $_{0.71}$ Na $_{0.29}$ Fe $_2$ As $_2$ crystal imply the presence of a large $T^2$ contribution to the specific heat which gives evidence of $d$ -wave order parameter symmetry in the superconducting state. To improve the measurements, a novel design for a calorimeter with a paramagnetic temperature sensor is presented. It promises a temperature resolution of $\Delta T \approx 0.1 \, \mathrm{\mu K}$ and an addenda heat capacity less than $200 \, \mathrm{pJ/K}$ at $ T < 100 \, \mathrm{mK}$ .     

Measurements of Microstructural, Mechanical, Electrical, and Thermal Properties of an Al–Ni Alloy

The Al–7.5 wt% Ni alloy was directionally solidified upwards with different temperature gradients, $G$ ( $0.86\,\text{ K}~{\cdot }~ \text{ mm}^{-1}$ to $4.24\,\text{ K}~{\cdot }~\text{ mm}^{-1})$ at a constant growth rate, $V$ ( $8.34\,\upmu \text{ m}~{\cdot }~\text{ s}^{-1})$ . The dependence of dendritic microstructures such as the primary dendrite arm spacing ( $\lambda _{1}$ ), the secondary dendrite arm spacing ( $\lambda _{2}$ ), the dendrite tip radius ( $R$ ), and the mushy zone depth ( $d$ ) on the temperature gradient were analyzed. The dendritic microstructures in this study were also compared with current theoretical models, and similar previous experimental results. Measurements of the microhardness (HV) and electrical resistivity ( $\rho $ ) of the directionally solidified samples were carried out. Variations of the electrical resistivity ( $\rho $ ) with temperature ( $T$ ) were also measured by using a standard dc four-point probe technique. And also, the dependence of the microhardness and electrical resistivity on the temperature gradient was analyzed. According to these results, it has been found that the values of HV and $\rho $ increase with increasing values of $G$ . But, the values of HV and $\rho $ decrease with increasing values of dendritic microstructures ( $\lambda _{1}, \lambda _{2}, R,$ and $d$ ). It has been also found that, on increasing the values of temperature, the values of $\rho $ increase. The enthalpy of fusion ( $\Delta {H}$ ) for the Al–7.5 wt%Ni alloy was determined by a differential scanning calorimeter from a heating trace during the transformation from solid to liquid.     

Full-Potential Calculation of Structural, Electronic, and Thermodynamic Properties of Fluoroperovskite \text{ CsMF}_{3} (M?=?Be and Mg)

The structural and electronic properties of the cubic fluoroperoveskite $\text{ CsBeF}_{3}$ and $\text{ CsMgF}_{3}$ have been investigated using the full-potential-linearized augmented plane wave method within the density functional theory. The exchange-correlation potential was treated with the local density approximation and the generalized gradient approximation. The calculations of the electronic band structures show that $\text{ CsBeF}_{3 }$ has an indirect bandgap, whereas $\text{ CsMgF}_{3}$ has a direct bandgap. Through the quasi-harmonic Debye model, in which the phononic effects are considered, the effect of pressure $P$ and temperature $T$ on the lattice parameter, bulk modulus, thermal expansion coefficient, Debye temperature, and the heat capacity for $\text{ CsBeF}_{3}$ and $\text{ CsMgF}_{3}$ compounds are investigated for the first time.     

Reparametrizing swung surfaces over the reals

Let $\mathbb {K}\subseteq \mathbb {R}$ be a computable subfield of the real numbers (for instance, $\mathbb {Q}$ ). We present an algorithm to decide whether a given parametrization of a rational swung surface, with coefficients in $\mathbb {K}(\mathtt {i})$ , can be reparametrized over a real (i.e., embedded in $\mathbb {R}$ ) finite field extension of $\mathbb {K}$ . Swung surfaces include, in particular, surfaces of revolution.     

Evidence for One-Gap Superconductivity in Mg(B_{1-x}C_{x})_{2} Single Crystals at x=0.132 by Point-Contact Spectroscopy

We report the results of directional point-contact measurements in Mg(B $_{1-x}$ C $_{x})_{2}$ single crystals. The amplitudes of the gaps, $\Delta_{\pi}$ and $\Delta_{\sigma}$ , were determined for each C content by fitting the experimental low-temperature normalized conductance curves of our “soft” point contacts with the BTK model generalized to the two-band case. We found that, on increasing the carbon content, $\Delta_{\sigma}$ decreases almost linearly with $T_{c}$ and $\Delta_{\pi}$ slightly increases until, at $x=0.132$ (where $T_{c}=19$ K), they assume the same value $\Delta =3.2 \pm 0.9$ meV. This result is confirmed by the temperature and magnetic-field dependence of the conductance curves at this C content, which do not show any evidence of two distinct gap values. In particular, the Δ versus T curve follows very well a standard BCS curve, with a gap ratio $2\Delta /k_{B} T_{c}=3.9$ . These experimental findings are compared to the theoretical predictions of the two-band model in the Eliashberg formulation.     

The theoretical calculation of the flow rate of granular matter from an inclined orifice

A theoretical calculation method for the flow rate of granular matter from an inclined orifice is discussed in this article and for the inclination angles at $\theta \le 90^{\circ }$ , a theoretical relation between the flow rate $Q$ and inclination angle $\theta $ is derived; and for the inclination angles at $\theta >90^{\circ }$ , a semi-theoretical relation is established. From the relations, we found that the ratio of the flow rate from a vertical orifice, $Q_{90}$ , to that from a horizontal orifice, $Q_{0}$ , is equal to the sine of the angle of repose $\theta _{\mathrm{r}}$ , i.e., $Q_{90} /Q_0 =\sin \theta _{\mathrm{r}} $ . The theoretical relations are tested by means of the experimental data and the results indicate that the theoretical calculating values are in good agreement with the experimental data over a wide range of the inclination angles. Therefore, the formula proposed in this article can be used for the theoretical calculation of the flow rate of granular matter from an inclined orifice. The relation $Q_{90} /Q_0 =\sin \theta _{\mathrm{r}}$ may be used as an alternative approach to obtaining $\theta _{\mathrm{r}}$ : measuring $Q_{90}$ and $Q_{0}$ , and then calculating $\theta _{\mathrm{r}} $ by using formula $\theta _{\mathrm{r}} =\arcsin (Q_{90} /Q_0 )$ .     

Multi-point evaluation in higher dimensions

In this paper, we propose efficient new algorithms for multi-dimensional multi-point evaluation and interpolation on certain subsets of so called tensor product grids. These point-sets naturally occur in the design of efficient multiplication algorithms for finite-dimensional $\mathcal C $ -algebras of the form $\mathcal A =\mathcal C [x_1, {\ldots }, x_n] / I$ , where $I$ is generated by monomials of the form $x_1^{i_1} {\cdots } x_n^{i_n}$ ; one particularly important example is the algebra of truncated power series $\mathcal C [x_1, {\ldots }, x_n] / (x_1, {\ldots }, x_n)^d$ . Similarly to what is known for multi-point evaluation and interpolation in the univariate case, our algorithms have quasi-linear time complexity. As a known consequence Schost (ISSAC’05, ACM, New York, NY, pp 293–300, 2005), we obtain fast multiplication algorithms for algebras $\mathcal A $ of the above form.     

Classification of Novikov algebras

We describe a method for classifying the Novikov algebras with a given associated Lie algebra. Subsequently we give the classification of the Novikov algebras of dimension 3 over $\mathbb{R }$ and $\mathbb{C }$ , as well as the classification of the 4-dimensional Novikov algebras over $\mathbb{C }$ whose associated Lie algebra is nilpotent. In particular this includes a list of all 4-dimensional commutative associative algebras over $\mathbb{C }$ .     

Thermal Conductivity of Standard Sands. Part III. Full Range of Saturation

The thermal conductivity $(\lambda )$ ( λ ) of three unsaturated standard quartz sands (Ottawa C-109 and C-190, and Toyoura) was measured by a transient thermal-conductivity probe, at room temperature of approximately $25\,^{\circ }\text{ C }$ 25 ° C and at loose and tight compactions. The measurements were carried out at different degrees of saturation $(S_\mathrm{r})$ ( S r ) from dryness to full saturation. In general, a sharp $\lambda $ λ increase was observed at low $S_\mathrm{r}$ S r , followed by a moderate rise until full saturation. However, experiments on loosely compacted C-190 samples revealed $\lambda $ λ deviation from a general trend ( $\lambda $ λ vs $S_\mathrm{r})$ S r ) caused by water percolation. Alternatively, successful experiments were carried out on loosely packed unsaturated C-190 samples using 1 % agar gel. For loosely compacted C-109 and Toyoura, $\lambda $ λ data obtained from 1 % agar gel closely agreed with $\lambda $ λ data for water as a saturation medium. The measured data were used to verify a model by de Vries for unsaturated soils. The model largely underestimates experimental data at $S_\mathrm{r}<0.5$ S r < 0.5 and produces an overall root-mean-square error of about $0.2\, \text{ W }~{\cdot }~\text{ m }^{-1}~{\cdot }~\text{ K }^{-1}$ 0.2 W · m ? 1 · K ? 1 . Measured $\lambda $ λ data agreed with data by a steady-state technique (a guarded hot-plate apparatus) at dryness and full saturation and exceeded the steady-state data in the unsaturated region. However, TCP data can be considered more reliable due to a lower temperature increase during $\lambda $ λ measurements and a shorter testing time. Consequently, in the case of unsaturated soils, evaporation and migration of water and steam can be avoided.     

Experimental Measurements of Thermophysical Properties of \mathrm{Al}_{2}\mathrm{O}_{3}– and \mathrm{TiO}_{2}–Ethylene Glycol Nanofluids

This paper presents measurements of the thermal conductivity and the dynamic viscosity of $\mathrm{Al}_{2}\mathrm{O}_{3}$ Al 2 O 3 –ethylene glycol and $\mathrm{TiO}_{2}$ TiO 2 –ethylene glycol (1 % to 3 % particle volume fraction) nanofluids carried out in the temperature range from $0\,^{\circ }$ 0 ° C to $50\,^{\circ }$ 50 ° C. The thermal-conductivity measurements were performed by using a transient hot-disk TPS 2500S apparatus instrumented with a 7577 probe (2.001 mm in radius) having a maximum uncertainty $(k=2)$ ( k = 2 ) lower than 5.0 % of the reading. The dynamic-viscosity measurements and the rheological analysis were carried out by a rotating disk type rheometer Haake Mars II instrumented with a single-cone probe (60 mm in diameter and $1^{\circ }$ 1 ° ) having a maximum uncertainty $(k=2)$ ( k = 2 ) lower than 5.0 % of the reading. The thermal-conductivity measurements of the tested nanofluids show a great sensitivity to particle volume fraction and a lower sensitivity to temperature: $\mathrm{TiO}_{2}$ TiO 2 –ethylene glycol and $\mathrm{Al}_{2}\mathrm{O}_{3}$ Al 2 O 3 –ethylene glycol nanofluids show a thermal-conductivity enhancement (with respect to pure ethylene glycol) from 1 % to 19.5 % and from 9 % to 29 %, respectively. $\mathrm{TiO}_{2}$ TiO 2 –ethylene glycol and $\mathrm{Al}_{2}\mathrm{O}_{3}$ Al 2 O 3 –ethylene glycol nanofluids exhibit Newtonian behavior in all the investigated temperature and particle volume fraction ranges. The relative viscosity shows a great sensitivity to the particle volume fraction and weak or no sensitivity to temperature: $\mathrm{TiO}_{2}$ TiO 2 –ethylene glycol and $\mathrm{Al}_{2}\mathrm{O}_{3}$ Al 2 O 3 –ethylene glycol nanofluids show a dynamic viscosity increase with respect to ethylene glycol from (4 to 5) % to 30 % and from 14 % to 50 %, respectively. Present experimental measurements were compared both with available measurements carried out by different researchers and computational models for thermophysical properties of nanofluids.     

Irreducible compositions of polynomials over finite fields of even characteristic

This paper presents some results with the constructive theory of synthesis of irreducible polynomials over a Galois field with even characteristic. We prove a theorem that plays an important role for constructing irreducible polynomials. By this theorem two recurrent methods for constructing families of irreducible polynomials of degree $n2^{k}~(k=1,2,\ldots )$ over $\mathbb F _{2^{s}}$ are proposed. It is shown that in this special case, the sequences of irreducible polynomials are N-polynomial of degree $2^{k}$ .     

Nuclear Spin Relaxation Characteristic of Submonolayer ^3He Films in Nanochannels

In order to obtain information on dynamics of helium films in the nondegenerate fluid region, we have performed a pulsed-NMR experiment at 3.29 MHz on $^3$ He films adsorbed in straight 2.4 nm channels of FSM silicates down to 0.54 K. In general, the spin-lattice and spin-spin relaxation times $T_1$ and $T_2$ were explained in terms of the two-dimensional Bloembergen–Purcell–Pound model for dipolar relaxation. Temperature dependences of $T_1$ in submonolayer $^3$ He films show a minimum, indicating that the dipolar-field correlation time $\tau _\mathrm {c}$ is about $\omega ^{-1}=4.8\times 10^{-8}$ s. The temperature $T_\mathrm {min}$ of the $T_1$ minimum monotonically lowers with increasing coverage, suggesting that $^3$ He adatoms become more mobile at higher coverages. The low-dimensional property of $^3$ He adatoms is observed as the separation of $T_1$ and $T_2$ above $T_\mathrm {min}$ where $\omega \tau _\mathrm {c}<1$ . On the other hand, several features specific to films in the nanochannel geometry were also found. Especially, the temperature dependence of $T_2$ becomes very small just below $T_\mathrm {min}$ and shows a shoulder at lower temperatures. This anomaly has not been observed in $^3$ He adsorbed in wider pores or on flat surfaces, so that it is considered to be characteristic of $^3$ He films confined in narrow channels with a diameter of a few nm.     

Rational formulas for traces in zero-dimensional algebras

We present a rational expression for the trace of the multiplication map Times _r : A → A in a finite-dimensional algebra ${A := \mathbb {K}[x_1,\ldots,x_n] /\mathcal {I}}$ in terms of the generalized Chow form of ${\mathcal{I}}$ . Here, ${\mathcal{I} \subset \mathbb {K}[x_1,\ldots,x_n]}$ is a zero-dimensional ideal, ${\mathbb {K}}$ is a field of characteristic zero, and r(x ₁,..., x _n ) a rational function whose denominator is not a zero divisor in A. If ${\mathcal {I}}$ is a complete intersection in the torus, we get numerator and denominator formulas for traces in terms of sparse resultants.     

Vorhersage der thermischen Strahlung großer Kohlenwasserstoff- und Peroxid-Poolfeuer mit CFD Simulation

Flame temperatures (T), surface emissive powers (SEP) and irradiances (E) of large-scale JP-4 pool fires (d=2, 8, 16, 25 m) and di-tert-butyl peroxide (DTBP) pool fires (d=1.12 m, 3.4 m) are investigated experimentally and by CFD simulation. As experimental methods an infrared thermographic camera system with video-mixing unit is used for the determination of T, SEP and an ellipsoidal radiometer for the determination of E. The maximum frequency of time-averaged emission temperatures for JP-4 pool fire (d=16 m) are in a range of $ 793\,\mathrm{K} < \overline{T} < 1033$ and for DTBP pool fire (d=1.12 m) are a range of $ 1040\,\mathrm{K} < \overline{T} < 1480\,\mathrm{K}$ . For DTBP pool fire (d=1.12 m), the measurements result in $ \overline{\text{SEP}}\approx 130\,\mathrm{kW/m^{2}}$ which is up to a factor of ≈6 larger in comparison to hydrocarbon pool fires (d≈1 m). In a case of DTBP pool fire (d=3.4 m) with $ \overline{\text{SEP}} \approx 250\,\mathrm{kW/m^{2}}$ this factor is ≈5 compared to $ \overline{\text{SEP}} \approx 50\,\mathrm{kW/m^{2}}$ of LNG pool fire (d=4 m). By increasing the relative distance ?y/d from the pool rim, measured time averaged irradiances $ \overline{E}$ (?y/d) decrease and agree well with CFD predicted $ \overline{E}_{\text{CFD}}$ (?y/d). Also, there is a good agreement between the measured time averaged $ \overline{T}$ and $ \overline{\text{SEP}}$ of hydrocarbons and DTBP pool fires, with the predicted $ \overline{T}_{\text{CFD}}$ and $ \overline{\text{SEP}}_{\text{CFD}}$ values. The possibilities and nowadays limitations of CFD simulation of large pool fires are discussed. This study has shown that the risk potential of accidental pool fires referring to thermal radiation can be predicted much better than in the past.