GO@MIL-101的制备及其对水中Cr（Ⅵ）的去除

通过水热法制备了掺杂氧化石墨烯（GO）的金属有机框架GO@MIL-101,并考察了GO掺杂量对GO@MIL-101形貌和性质的影响规律。GO的掺杂影响了MIL-101晶体的形成过程。随着GO掺杂量的增加,GO@MIL-101晶体的完整性降低、粒径减小,团聚现象越发显著。GO@MIL-101能够有效去除溶液中的Cr（Ⅵ）,该过程符合拟二级动力学方程。由Langmuir吸附等温线拟合得到的最大吸附量与GO掺杂量有关,在2%[相对于Cr（NO₃）₃·9H₂O质量]时达到最大,这与此时GO@MIL-101同时具有较大的比表面积和较大的孔体积有关。Cr（Ⅵ）的去除过程伴随着溶液中NO₃^-浓度的升高以及pH的下降,电荷平衡计量分析表明MIL-101和GO@MIL-101对Cr（Ⅵ）的去除机制相同,主要依靠MIL-101的离子交换作用,并且所去除的Cr（Ⅵ）以CrO₄^2-形式存在于固相中。     

胺功能化MIL-101(Cr)@SiO_2@Fe_3O_4催化剂及其Knoevenagel反应性能

采用溶剂热法在纳米SiO_2@Fe_3O_4磁性颗粒表面原位合成MIL-101(Cr),制备磁性MIL-101(Cr)@SiO_2@Fe_3O_4催化剂。采用甲胺、乙二胺和丁二胺对制备的磁性催化剂进行功能化,得到胺功能化NH2-MIL-101(Cr)@SiO_2@Fe_3O_4催化剂。利用XRD、FT-IR、BET、SEM、TEM和VSM等对催化剂结构进行表征,评价胺功能化NH2-MIL-101(Cr)@SiO_2@Fe_3O_4催化剂对糠醛和氰乙酸乙酯Knoevenagel缩合反应性能和重复使用性能,考察反应条件与催化性能的关系。结果表明,制备的新型胺功能化NH2-MIL-101(Cr)@SiO_2@Fe_3O_4催化剂具有MIL-101(Cr)的结构特征和良好的超顺磁性能,对糠醛和氰乙酸乙酯Knoevenagel缩合反应表现出很好的催化性能,其中,乙二胺功能化30%MIL-101(Cr)@SiO_2@Fe_3O_4催化剂对Knoevenagel缩合反应的性能最佳,在反应温度40℃和反应时间1 h条件下,氰乙酸乙酯转化率为97. 0%,产物选择性接近100%。反应后磁性催化剂可以通过外磁场容易进行分离,重复使用5次,氰乙酸乙酯转化率仍大于93%。     

L酸/B酸可调的磺酸功能化MIL-101(Cr)材料催化葡萄糖脱水 制备5-羟甲基糠醛

以九水合硝酸铬和单磺酸钠对苯二甲酸为原料,水为溶剂,采用水热法合成系列磺酸功能化MIL-101（Cr）,通过调节反应温度和时间,合成不同Lewis/Brönsted催化位点比例的磺酸功能化MIL-101（Cr）,采用PXRD、EDX、SEM、ICP-AAS及BET比表面积分析等技术对材料进行综合表征,并研究磺酸功能化MIL-101（Cr）催化葡萄糖脱水制备5-羟甲基糠醛的催化活性。催化反应动力学研究结果表明,MIL-101（Cr）-SO₃H中的Cr（Ⅲ）作为葡萄糖异构化反应的Lewis酸位点,－SO₃H作为果糖脱水反应的Brönsted酸催化位点,当催化剂的Brönsted酸和Lewis酸的摩尔比为1.1时,150℃下反应,5-羟甲基糠醛的选择性最高可以达到47.15%,5-羟甲基糠醛的产率最高达到46.0%。     

Effect of Pd precursor salt on the activity and stability of Pd-doped hexaaluminate catalysts for the CH4 catalytic combustion

This study reports the influence of palladium salt precursor on the catalytic activity of palladium-doped hexaaluminate catalysts for the combustion of 1 vol% CH₄ in the presence of CO₂ and H₂O as inhibitors. Thermal stability of the catalysts is evaluated in long-term catalytic test at 700 °C. The hexaaluminate supports were synthesized using two different procedures: conventional coprecipitation and solid/solid diffusion procedure. Palladium impregnation was carried out by two different routes using Pd(NO₃)₂ in water or Pd(acac)₂ in toluene as impregnation solution. It was observed that using Pd(acac)₂ as precursor allows to attain higher dispersion of the active phase (Pd particles size <3 nm). Compared to the catalysts obtained by impregnation of Pd(NO₃)₂, higher catalytic activities are then obtained. Nevertheless, a deactivation of the samples obtained using Pd(acac)₂ is observed. At the end of the stability test, almost similar catalytic activity is obtained whatever the palladium precursor. Reduction–reoxidation experiment showed that this deactivation is irreversible, and TEM analysis suggest that this deactivation is related to the sintering of Pd particles under reaction over samples synthesized using Pd(acac)₂ as precursor.     

The chemical anchoring of noble metal amine precursors to silica

The effect of pretreatment on the dispersion of supported noble metal Catalyst prepared from amine precursors in basic solution have been studied. The following metal precursors were used: Pt(NH₃)₄(NO₃)₂, Pd(NH₃)₄(NO₃)₂, Ru(NH₃)₆Cl₃ and [Rh(NH₃)₅Cl]Cl₂ Pretreatment in oxygen, prior to reduction in H₂ at 400C, resulted in poor dispersions for Ru and Rh, moderate dispersions for Pd and high dispersions for Pt. Pretreatment in H₂ resulted in poor dispersions for Pd and Pt and high dispersions for Ru and Rh. Decomposition of the adsorbed Pt and Pd precursors in argon resulted in very high dispersions.     

表面修饰对镧锶钴铁阴极材料电化学性能的影响

通过柠檬酸-EDTA络合法制备固体氧化物燃料电池阴极材料La_0.6Sr_0.4Co_0.2Fe_0.8O_3-δ(LSCF)粉体。以Sm_0.2Ce_0.8O_1.9(SDC)为电解质,制备了LSCF/SDC/LSCF对称电极。采用浸渍法在LSCF/SDC/LSCF两侧浸渍La(NO₃)₃、Ni(NO₃)₂、Fe(NO₃)₃混合溶液,850℃烧结后得到表面修饰后的阴极材料。研究了浸渍烧结后表面修饰阴极材料的物相结构特征、电化学交流阻抗、电化学催化活性及单电池输出性能。结果表明:通过浸渍法在LSCF阴极表面形成了与LSCF结构相似的La_0.62Sr_0.38Ni_0.03Co_0.19Fe_0.78O_3-δ(LSNCF)固溶体,在表面产生的纳米颗粒提升了阴极材料对O2的吸附解离能力,并表现出较低的极化阻抗,在800℃时LSNCF阴极材料的极化面电阻为0.083Ω·cm²,在800℃连续工作7 200 min后,LSNCF阴极材料对称电池极化阻抗为0.117Ω·cm²。以Ni-SDC为阳极,SDC为电解质,LSNCF为阴极组装阳极支撑单电池,在750℃时最大功率密度为693 m W/cm²。     

Au基MOFs双功能催化剂的制备及其催化CO2与苯胺/H2反应性能

以UiO-66(Zr)、MIL-100(Fe)、MIL-100(Cr)、MIL-101(Cr)、NH 2-MIL-101(Al)为载体,Au为活性组分,制备Au/UiO-66(Zr)、Au/MIL-100(Fe)、Au/MIL-100(Cr)、Au/MIL-101(Cr)、Au/NH 2-MIL-101(Al)双功能催化剂。采用XRD、BET、NH 3-TPD、HRTEM等表征催化剂的结构,在釜式反应器中评价催化剂对CO 2与苯胺/H 2反应生成N-甲基苯胺与N,N-二甲基苯胺的N-甲基化反应性能,考察反应条件对催化剂催化性能的影响。结果表明,催化剂的XRD特征衍射峰与相应MOFs的模拟特征峰基本一致;负载Au后催化剂仍具有高的比表面积和大的孔容、孔径;不同MOFs负载Au的催化剂具有不同的酸强度和酸量;Au纳米粒子的分散性很好,粒径为(3~7)nm。制备的催化剂均具有催化CO2与苯胺/H2的N-甲基化反应性能,其中质量分数2%Au/MIL-101(Cr)催化剂催化性能最好,苯胺转化率为45.26%,N-甲基苯胺和N,N-二甲基苯胺选择性分别为73.50%和26.50%,重复使用性能优异。     

氨基MIL-101(Cr)强化CO2分离性能的混合基质膜优化制备

金属有机骨架MIL-101(Cr)是大孔径、高孔隙率的新型膜材料，可显著提升混合基质膜的CO₂渗透性，但其掺杂会明显降低选择性，有两方面原因：有机配体的CO₂亲和性较低；填料干燥活化后再分散性差，易团聚形成缺陷。对此，首先以氨基对苯二甲酸为配体合成氨基MIL-101(Cr)，提高溶解选择性，再采用先浇铸-后活化的制膜工艺，减少团聚缺陷。红外测试表明氨基填料成功合成；扫描电镜表明膜中填料分布均匀。掺杂15%(质量)氨基MIL-101(Cr)的乙基纤维素混合基质膜，CO₂渗透系数达到200 barrer，比MIL-101(Cr)膜提高11.2%，较纯聚合物膜提高133.1%；同时，CO₂/N₂选择性达到23.9，比MIL-101(Cr)膜提高25.8%，较纯聚合物膜提高17.1%。综上，采用先浇铸-后活化的制膜工艺掺杂氨基MIL-101(Cr)填料，可同时提高混合基质膜的CO₂渗透性和选择性。     

Hydrogen production by oxidative methanol reforming on Pd/ZnO: Catalyst preparation and supporting materials

Pd and Pd–Zn alloy were supported on various supporting materials using impregnation, co-precipitation and microemulsion methods, and their catalytic performances in oxidative methanol reforming (OMR) were investigated. Pd/ZnO exhibited much higher selectivity than either Pd/Al₂O₃ or Pd/ZrO₂ in the OMR for hydrogen production. This was attributed to the presence of Pd–Zn alloy on the ZnO support. Elemental Pd on Al₂O₃ or ZrO₂ promotes methanol decomposition reaction and increases CO formation. Using a microemulsion method, a highly selective Pd/ZnO can be obtained with much lower Pd loading than that in samples prepared by co-precipitation. Modification of Al₂O₃ with ZnO produced a ZnAl₂O₄ phase, which was found to be a good support for the Pd/ZnO catalyst. Highly active and selective Pd/ZnO/ZnAl₂O₄ catalysts for the OMR reaction, containing much lower Pd loadings have been developed by impregnation of the supports with an aqueous solution of Pd(NO₃)₂ + Zn(NO₃)₂.     

Direct synthesis of single-phase α-CaSO4·0.5H2O whiskers from waste nitrate solution

Single-phase α-CaSO₄·0.5H₂O whiskers were directly synthesized from waste Ca(NO₃)₂ solution using a hydrothermal method, and HNO₃ was synchronously regenerated. The effects of reaction temperature and Ca²⁺ concentration on the phase composition and morphology of products were determined by X-ray diffraction and optical microscopy. On the basis of the experimental results, the formation diagram of α-CaSO₄·0.5H₂O was plotted within the range of 5-35 g·L^-1 Ca²⁺ and 115℃-150℃. In addition, the conditions of the direct synthesis of α-CaSO₄·0.5H₂O were determined. Well-crystallized, single-phase α-CaSO₄·0.5H₂O whiskers with high aspect ratios (length, 1785 μm; diameter, 10.63 μm; aspect ratio, 168) and HNO₃ (70.25 g·L^-1) were obtained at the optimal conditions of 25 g·L^-1 Ca²⁺ and 125℃.     

MIL-101Cr-F/Cl用于N2O的捕集研究

氧化亚氮（N₂O）是仅次于CO₂和CH₄的第三大温室气体,对其捕集具有资源回收和减排温室气体的双重价值。本文通过添加氢氟酸和盐酸合成了末端具有不同阴离子的MIL-101Cr材料：MIL-101（Cr）-F和MIL-101（Cr）-Cl,通过XRD、BET、SEM等对样品进行了表征,测试并分析了两种样品对N₂O和N₂的吸附性能,进行了选择性和吸附热的计算以及混合气体的穿透模拟。研究结果表明,MIL-101（Cr）-Cl拥有目前最高的N₂O吸附容量（6.43 mmol/g,298 K）和N₂O/N₂选择性（267）,混合气体（N₂O/N₂=0.1%/99.9%）穿透模拟结果显示MIL-101（Cr）-Cl具有更加优异的微量N₂O捕获能力。     

Obtaining CeO2–ZrO2 mixed oxides by coprecipitation: role of preparation conditions

The preparation of CeO₂–ZrO₂ mixed oxides preparation was studied by evaluating the influence of several conditions. Coprecipitation was taken as the standard method and the effects brought about by the cerium salt precursor ((NH₄)₂Ce(NO₃)₆ or Ce(NO₃)₃), the introduction of drying and aging steps as well as pH controlling upon precipitation were analyzed. The samples were characterized by X-ray diffraction, Raman spectroscopy, temperature-programmed reduction, infrared spectroscopy, oxygen storage capacity and surface area. The use of Ce(NO₃)₃ leads to the formation of c-CeO₂ and t-ZrO₂ mixed oxide whereas a solid solution is achieved by using (NH₄)₂Ce(NO₃)₆. It was observed that the cerium precursor is the most significant parameter of preparation procedure since it defines the crystalline phases and consequently the reducibility behavior of the CeO₂–ZrO₂ system.     

Co改性活性炭吸附NO的实验研究

采用Co(NO_3)_2对活性炭进行改性,考察浸渍浓度和吸附温度等条件对活性炭吸附NO性能的影响,并对已吸附NO的0.3 mol·L~(-1)的Co(NO_3)_2改性活性炭进行再生。通过BET、SEM、吸附等温线和FT-IR表征样品的比表面积、颗粒形貌和表面官能团。结果表明,当浸渍溶液浓度为0.3 mol·L~(-1)时,吸附效果最佳,80 min时吸附效率达88.90%。活性炭的吸附效率随着温度升高而降低,用0.3 mol·L~(-1)Co(NO_3)_2改性的活性炭在200℃时的吸附效率大于90%,并可持续50 min。SEM和FT-IR表征结果表明,在Co(NO_3)_2改性的活性炭表面和孔隙生成了Co_3O_4,促进NO催化氧化为NO_2并进行吸附。加热再生后的0.3 mol·L~(-1)Co(NO_3)_2改性活性炭对NO的吸附效率在60 min内仍高于88.90%,再生效果较好,可持续再生利用。     

Preparation of novel magnetic nanoparticles as draw solutes in forward osmosis desalination

Novel magnetic nanoparticles (MNPs), Fe₃O₄@SiO₂ and Fe₃O₄@SiO₂@PEG-(COOH)₂, were prepared by loading different amounts of SiO₂ or/and PEG-(COOH)₂ onto Fe₃O₄ nanoparticles, and their feasibility to be used as forward osmosis (FO) draw solutes was investigated. The characterization of the materials showed that, compared to normal Fe₃O₄ nanoparticles, the modified MNPs exhibited enhanced dispersity and high osmotic pressure in aqueous solution. The FO experiment indicated that the synthesized draw solutes could obtain a water flux as high as 10 L·m^-2·h^-1 with an aquaporin FO membrane. The optimal concentration of the added tetraethyl orthosilicate was 30% during the synthesis. The novel MNPs could be easily recovered from draw solutions by magnetic field, and the recovery rate of Fe₃O₄@SiO₂ and Fe₃O₄@SiO₂@PEG-(COOH)₂ was 83.95% and 63.37%, respectively. Moreover, after 5 recycles of reuse, the water flux of Fe₃O₄@SiO₂ and Fe₃O₄@SiO₂@PEG-(COOH)₂ as draw solutes still remained 64.36% and 85.26%, respectively. The experimental results demonstrated that the synthesized core–shell magnetic nanoparticles are promising draw solutes, and the Fe₃O₄@SiO₂@PEG-(COOH)₂ was more suitable to be used as draw solute in FO process.     

β-SiC粉体中常见金属杂质的亚临界水热去除工艺

高纯β-SiC粉体作为原料,广泛应用于半导体晶圆、半导体窑具、半导体芯片设备用陶瓷器件等产品。高温高压可以促进水热反应,采用亚临界水热法可去除工业合成β-SiC粉体中的金属杂质。研究不同酸体系下β-SiC粉体中常见金属杂质的去除效果。利用电感耦合等离子原子发射光谱仪(ICP-OES)检测微量元素的含量,通过X射线衍射仪(XRD)和扫描电镜(SEM)对β-SiC粉体的物相组成和微观结构进行表征。结果表明,对于Cr和Zr去除效果较好的是HCl体系,对于Ca、Fe、Mg和Ti去除效果较好的是HCl+HF+HNO₃体系,对于Al和K去除效果较好的是H₂SO₄+(NH₄)₂SO₄体系。采用HCl体系处理的最佳反应温度为200 ℃,采用HCl+HF+HNO₃体系处理的最佳反应温度是220 ℃,采用H₂SO₄+(NH₄)₂SO₄体系处理的最佳反应温度是200 ℃。其中,H₂SO₄+(NH₄)₂SO₄体系可将β-SiC粉体中常见金属杂质含量降低至最少(杂质总含量为920.31 mg/L),因此该体系为β-SiC粉体除杂的最优方案。     

Formation and stability of barium aluminate and cerate in NOx storage-reduction catalysts

The formation and stability of BaAl₂O₄ and BaCeO₃ in Pt-Ba/Al₂O₃ and Pt-Ba/CeO₂ based NO_x storage-reduction (NSR) catalysts has been investigated using kinetic measurements, X-ray diffraction, thermal analysis and X-ray absorption spectroscopy. In as-prepared state, the Ba-component in the NSR catalysts was made up of amorphous BaO and BaCO₃. The formation of BaAl₂O₄ started above 850 °C, whereas the formation of BaCeO₃ was already observed at 800 °C and was faster than that of BaAl₂O₄. The stability of BaAl₂O₄ and BaCeO₃ in various liquid and gaseous atmospheres was different. BaAl₂O₄ was rapidly hydrated at room temperature in the presence of water and transformed to Ba(NO₃)₂ and γ-alumina in the presence of HNO₃, whereas BaCeO₃ was decomposed to much lower extent under these conditions. Interestingly, BaCeO₃ was transformed to Ba(NO₃)₂/CeO₂ in the presence of NO₂/H₂O at 300–500 °C. Also, the presence of CO₂ led to decomposition of barium cerate, which has important consequences for the catalyst ageing under NO_x-storage conditions and can be exploited for regeneration of thermally aged NSR-catalysts.     

不同NO3-浓度An/A/O-SBR系统PAOs-GAOs竞争及N2O释放特性

采用厌氧/缺氧/好氧运行的序批式生物反应器（An/A/O-SBR）,经不同NO₃^-浓度（10,20,30和40 mg/L,以氮计）长期驯化,考察了不同NO₃^-条件下An/A/O-SBR脱氮除磷及N₂O释放特性,基于不同微生物降解特性分析,确定了不同NO₃^-浓度下SBR系统内反硝化聚磷菌（denitrifying phosphorus accumulating organisms,DPAOs）和聚糖菌（glycogen-accumulating organisms, GAOs）竞争关系。结果表明：随NO₃^-浓度增加,总氮（TN）去除率由90%以上降至41.3%,TP去除率呈先增高后降低的趋势,N₂O产率（N₂O_emission/NO_x^-_removal）分别为1.68%、4.17%、8.92%和14.28%。An/A/O-SBR内微生物呈PAOs和GAOs共存的污染物降解特性,高浓度NO₃^-缺氧吸磷过程出现NO₂^-积累,抑制DPAOs活性,GAOs碳源竞争能力增强,NO₃^--N由10 mg/L增至40 mg/L,厌氧阶段PAOs的COD耗量比例由33.5%降至25.1%,相应GAOs的COD耗量由59.3%增至74.1%。DPAOs-GAOs共生体系内,反硝化过程NO₂^-/HNO₂积累耦合反硝化聚糖菌比例增加,加剧了高NO₃^-下An/A/O-SBR内N₂O释放。     

Oxidation behaviour and catalytic properties of Pd/Al2O3 catalysts in the total oxidation of methane

A series of Pd/Al₂O₃ catalysts with a wide range of mean Pd particle sizes (ca. 2–30 nm in diameter) was prepared by using various precursors (H₂PdCl₄, Pd(NO₃)₂ and Pd(AcAc)₂) and pre-treatments. The mean particle size of reduced samples was determined by H₂ chemisorption. The catalytic activity in methane oxidation under lean burn conditions was measured. The oxidation of reduced samples was studied at 300 °C. The extent of oxidation was found to decrease with increasing mean particle size. While small particles (<5 nm) oxidised very rapidly, the oxidation of large particles (ca. >15 nm) proceeded via a two-step process, being first fast and then slow. The decomposition of oxide species was studied by temperature-programmed experiments under vacuum. Two distinct oxidised species with different stability were evidenced depending on the particle size. Oxidised species in larger particles were found of lower stability than in smaller ones. A correlation between the existence of distinct types of oxide species and catalytic properties in methane oxidation was discussed.     

Preparation and characterization of Pd-Pb catalysts for selective hydrogenation

The preparation of Pd/-Al₂O₃ and Pd-Pb/-Al₂O₃ catalysts using Pd-acetylacetonate and tetrabutyl-lead (TBPb) has been studied. In the monometallic catalyst the precursor decomposition in air leads to a well dispersed Pd phase. Reacting the Pd/-Al₂O₃ (0.19%) catalyst with TBPb in the presence of adsorbed hydrogen, produces one mol of hydrocarbons (mainly butane) per mol of Pb fixed, suggesting the formation of a surface intermediate; Pd-Pb(C₄H₈)₃. In the absence of hydrogen, the reaction is slower and the evolution of hydrocarbons (mainly butenes) decreases by a factor of 2. As the amount of Pb fixed by both procedures is the same, Pb/Pd₃ = 1.3, other surface compounds must be involved. Characterization by H₂ and CO chemisorption and FTIR spectroscopy of adsorbed CO shows that Pb addition produces a dilution of the surface Pd atoms, preventing the dissociative adsorption of H₂ and inducing the adsorption of CO in the linear form. The XPS spectra of Pd/-Al₂O₃ and Pd-Pb/-Al₂O₃ (0.19 %– 0.27%) indicate a Pb 4f/Pd 3d ratio of 1.4 and a decrease in the Pd 3d/Al 2s intensity ratio with Pb addition. These results suggest that Pb is well dispersed and in close contact with the Pd surface.     

氮杂环卡宾-钯功能化的配位聚合物（NHC-Pd@Zn-L）：合成、表征及催化Suzuki-Miyaura交叉偶联反应

以\mathrm{1,3}-二(1-羧乙基)咪唑盐(HL)和Zn(NO₃)₂·6H₂O反应合成二维配位聚合物[Zn(L)₂] _n (Zn-L)，产物再与K₂PdCl₄在四氢呋喃溶液中反应引入氮杂环卡宾-钯（NHC-Pd）催化位点，制得催化剂NHC-Pd@Zn-L，并通过PXRD、TGA、ICP、SEM、EDS和XPS进行表征。结果表明，NHC-Pd@Zn-L具有良好的热稳定性且修饰后晶体的框架结构没有发生变化，Pd以NHC-Pd的形式结合在Zn-L中，并均匀分散在配位聚合物中。将NHC-Pd@Zn-L用于催化Suzuki-Miyaura交叉偶联反应，当以苯硼酸和溴苯为底物，催化剂用量为15 mg，乙醇为溶剂，碳酸钾为碱的条件下60℃反应6 h，产率达到>99%，而且催化剂易于回收并可循环使用3次。