共查询到20条相似文献,搜索用时 328 毫秒
1.
综合考虑板形检测辊自重及其所受带钢张力的影响,利用正弦波和样条曲线虚拟各通道的零点偏差,基于截点法建立了针对检测辊挠度动态变化的原始波形零点补偿模型。对于检测辊自重造成的离线零点偏差,对其进行虚拟正弦截点补偿;对于动态大张力造成的在线零点偏差,利用样条曲线实时拟合零点偏差。从实测曲线中减去零点偏差拟合曲线,即可获得更稳定的径向压力值或板形值,应用过程中还可以采用递推平滑法使其更可靠地反映在线带钢的实际板形状况。实测数据表明,各通道的原始波形AD零点偏差从补偿前的600左右下降到补偿后的50以内,径向压力零点偏差从130N左右下降到10N以内。因此,该零点补偿方法对于提高板形检测精度和板形控制精度具有重要的意义。 相似文献
2.
针对影响提高扇形段在线辊缝控制精度的问题,分析对比了扇形段的主要几种结构型式及存在的不足,研发出了具有自主知识产权的无间隙辊缝调节扇形段,并在多台板坯连铸机上成功运用。对于扇形段刚度引起的辊缝控制偏差,基于仿真分析与样机测试相结合的方法,获得了扇形段在不同夹紧液压缸压力条件下的弹性变形量,通过该变形量对辊缝进行补偿,提高了在线辊缝控制精度,获得良好的应用效果。对于扇形段不同倾动角度的影响,通过对扇形段在不同倾动角度条件下的受力分析,推导获得了扇形段不同倾动角度与进出口辊缝偏差之间的补偿关系。研究所提出的改进方法对实现扇形段辊缝的在线精准控制具有重要的指导意义。 相似文献
3.
轧辊磨削质量直接影响冷轧带钢的质量。从磨削加工的特点入手,分析了走刀痕产生的原因,认为磨床设备精度差、砂轮材质不均、砂轮修磨形状不良、轧辊辊型偏差大、磨削参数不匹配、磨削液循环过滤不良都会导致走刀痕。举例说明了不同分布特征走刀痕缺陷的控制方法。磨削参数不匹配导致的走刀痕,主要通过调整各个磨削阶段的磨削压力、砂轮转速和横移速度、增加磨削道次来改进磨削质量。若辊型偏差大于50μm,主要通过优化磨削进给量或分段控制磨削参数的方法,将辊型偏差控制在20μm以内,然后再采用正常的磨削参数进行磨削,控制走刀痕的产生。 相似文献
4.
5.
6.
7.
针对破鳞拉矫机的设备组成及生产工艺特点,开发了以插入量和延伸率控制为核心的自动控制系统.建立了插入量的控制模型,解决了因换辊后频繁标定零点位置以及辊子磨损影响插入量控制精度的问题.采用参数寻优的方法,求解以误差为基础的目标函数得出适配参数,解决了延伸率控制中的参数设置合理性受人为因素影响较大的问题.现场实际应用效果表明:破鳞效果良好,弯曲辊和矫直辊的标定值与计算值的最大偏差均可控制在0.24 mm以内;延伸率控制采用参数寻优前后效果对比明显,设定值为0.9%时,偏差控制精度由±8%提高到±5%,设定值为1.8%时,偏差控制精度由±3%提高到±1%. 相似文献
8.
介绍了立辊轧机控制系统的基本组成、控制原理及其应用,同时还介绍了轧机的自学习功能。实践证明,梅钢热轧板厂立辊轧机的应用是成功的,并在实际生产中取得了良好的效果。 相似文献
9.
10.
基于几何关系和板形检测理论,建立了针对检测辊安装误差的在线板形信号误差补偿模型。结合轧机设备布局特点和工艺参数,针对固定包角和变包角两种安装方法,从水平误差和垂直误差2个方面,对在线板形信号进行综合误差的定量补偿。对于固定包角方式,检测辊安装精度的板形补偿量可设定为一常数;对于变包角方式,则需要根据变动态包角计算公式,在线实时计算动态补偿量。基于理论分析和工业实际数据,制定适合轧机自身特点的检测辊允许安装误差,才能最大限度地提高板形检测精度,使综合补偿后的板形曲线更真实地反映在线冷轧带钢的实际板形状况。以某1050冷轧机为例,其水平误差和垂直误差建议分别控制在0.03和0.05mm以内,才能满足基本的板形控制技术要求。 相似文献
11.
Jiankang Xing Yan Peng Jianliang Sun Caiyi Liu Silvia Barella Andrea Gruttadauria Marco Belfi Carlo Mapelli 《国际钢铁研究》2023,94(9):2300022
Flatness and surface quality are important quality indexes of strip steel, and roll wear will directly affect the product's flatness and surface quality. Online roll profile measurement technology can obtain the information of roll profile in real time, guide the optimization of roll change rhythm, and improve the flatness control ability of rolling mill and surface quality of strip product. However, the error caused by roll displacement, clearance, roll thermal crown, and other factors is usually the same order of magnitude as the roll shape or roll wear, or even one order of magnitude higher. So error compensation is the key to ensuring the accuracy of online roll profile measurement. Herein, the position measurement technology of the roll bearing block is considered in the online roll profile measurement, and the measurement error caused by the deviation of the roll axis is separated. The thermal crown model is established to separate the measurement errors caused by the thermal crown. The error compensation model of online roll profile measurement is established, and the simulation calculation is carried out. This error compensation method is of great significance to improve the accuracy of online roll profile measurement and realize the fine management of mill roll in service. 相似文献
12.
《Baosteel Technical Research》2010,(Z1):114
Improving efficiency in roll grinding process is a critical issue in the steel mill.Each roll has to be grinded to a well-defined profile and then to be measured for quality check.However,the surface conditions are inspected by using different on-line inspection probes equipped on the grinder.The roll number is a unique information which can be used to merge with a huge amount of measurement data so that the condition of each roll is fully monitored.One of the key factors that hinder the efficiency in such process is the errors and time consumption due to human intervention.In order to mitigate these issues and to realize the fully automatic grinding process,radio frequency identification technology(RFID) could be a solution and has been developed in this paper.It is well known that when an RFID tag is placed directly upon a metallic object,in the absence of a gap or a substrate,it functions rather poorly and even becomes totally dysfunctional.This limitation,in turn,poses a real barrier to the use of the RFID on metallic objects.This paper proposes a miniature RFID tag antenna design for application on roll number identification.The experimental tests show that the maximum read range of the proposed RFID tag placed on a roll is approximately 1.5m and the overall size is only 32×18×3.2 mm~3.An RFID system for roll number identification was used in a roll shop and several remarkable improvements were achieved,including the completely automatic grinding process and the error-free identification,as well as the high personnel safety operation. 相似文献
13.
国内大量应用的1 700 mm以下的UCM冷连轧机组不具备工作辊窜辊功能,只能依靠工作辊边部辊形设计对硅钢板带进行边降控制。提出了针对UCM冷连轧机的工作辊端部辊形设计方法,在大幅提高边降控制能力的同时,通过边部保护段的设计有效减少断带风险。辊形曲线有利于轧辊磨削,避免轧辊表面质量对带钢表面造成影响。充分利用工作辊与中间辊弯辊的板形调控特性,使用高效实用的弯辊力组合板形控制方法,对轧制过程中产生的二次和四次板形缺陷实施快速精确的控制,在控制硅钢边降的同时很好地抑制板形问题,具有重要的研究价值与推广前景。 相似文献
14.
15.
16.
针对硅钢退火线跑偏问题,通过对轧硬卷带钢在退火线辊面上运行的受力分析,结合马钢冷轧硅钢六辊可逆轧机实际板形,得出轧机板形与退火线跑偏的关联性。根据硅钢产线实际状况及板形与跑偏的关联性分析,制定退火线跑偏改善有效措施,并配合退火线辊系改造及纠偏能力提升,对跑偏治理具有关键性作用。 相似文献
17.
影响轧辊表面粗糙度的因素很多,为此对影响辊面粗糙度的因素进行了系统分析和实验研究,得出了轧辊和砂轮的速度、砂轮粒度、砂轮直径及磨削液等主要因素对轧辊表面粗糙度影响的一般规律。利用回归分析的方法建立了轧辊表面粗糙度的数学模型,并将计算值与实测值进行了比较,发现两者基本一致。此项研究为适时控制冷轧带钢在线磨辊辊面粗糙度提供了计算模型。 相似文献
18.
19.