Synthesis of cis‐1,4‐polyisoprene with Al‐Ti catalysts modified by different electron donor reagent

The preparation of the high cis ?1,4‐polyisoprene by Ziegler‐Natta catalysis system was studied. The effect of Al‐Ti catalysts modified by ethers with different structures which are different electron donor reagent on polymerization of isoprene has been mainly investigated. By the measurement method of the monomer conversion, FTIR, and ¹H NMR spectroscopy, the influence of, respectively, added diphenyl ether, anisole, dibutyl ether, or methyl tert ‐butyl methyl ether as a third active component on the heterogeneous TiCl₄‐Al(i ‐Bu)₃‐ether catalyst activity and microstructure of synthetic polyisoprene was analyzed. By the adding of diphenyl ether or dibutyl ether, the process of prefabricated heterogeneous catalyst is quickly and catalyst particle quantity is large. The polymerization conversion is high and the microstructure cis ?1,4 content of the resulting polymer can reach 92%. But Al(i ‐Bu)₃ added anisole or methyl tert ‐butyl methyl ether hard to cooperate with TiCl₄. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133 , 44357.     

Highly trans‐1,4‐specific polymerization of 1,3‐butadiene catalyzed by [2,6‐bis{(4S)‐ (−)‐isopropyl‐2‐oxazolin‐2‐yl}pyridine] chromium complex activated with modified methylaluminoxane

Chromium complexes with N,N,N‐tridentate ligands, LCrCl₃ (L = 2,6‐bis{(4S)‐(?)‐isopropyl‐2‐oxazolin‐2‐yl}pyridine ( 1 ), 2,2′:6′,2″‐terpyridine ( 2 ), and 4,4′,4″‐tri‐tert‐butyl‐2,2′:6′,2″‐terpyridine ( 3 )), were prepared. The structures of 1 and 2 were determined by X‐ray crystallography. Upon activation with modified methylaluminoxane (MMAO), 1 catalyzed the polymerization of 1,3‐butadiene, while 2 and 3 was inactive. The obtained poly(1,3‐butadiene) obtained with 1 ‐MMAO was found to have completely trans‐1,4 structure. The 1 ‐MMAO system also showed catalytic activity for the polymerization of isoprene to give polyisoprene with trans‐1,4 (68%) and cis‐1,4 (32%) structure. Copyright © 2011 Society of Chemical Industry     

High cis‐1,4 polyisoprene or cis‐1,4/3,4 binary polyisoprene synthesized using 2‐(benzimidazolyl)‐6‐(1‐(arylimino)ethyl)pyridine cobalt(II) dichlorides

Polyisoprene (PI) with a high content of cis‐1,4 (up to 95%) or cis‐1,4/3,4 binary structures was synthesized using a cobalt system in toluene. The cobalt system, which exhibited high activities (up to 3.50 × 10⁶ g PI (mol Co)^?1 h^?1), contained a series of 2‐(benzimidazolyl)‐6‐(1‐(arylimino)ethyl)pyridine cobalt(II) dichlorides activated with ethylaluminium sesquichloride. The nature of the ligands and the reaction conditions significantly affected both the catalytic performance of the cobalt complexes as well as the structures of the resultant PI. The stereospecific polymerization of isoprene could be tuned via changing either the co‐catalyst or solvent: for example, increased content of 3,4 PI (up to 36.6%) was achievable in heptane in the presence of diethylaluminium chloride. Sequence distribution analysis by ¹³C NMR spectroscopy indicated that most 3,4 units occurred randomly in the PI chains. © 2013 Society of Chemical Industry     

Microstructure and glass‐transition temperature of novel star N‐SIBR

In this study, a polymeric N‐functionalized mutilithium (N‐M‐Li) compound was prepared from commercial divinylbenzene (DVB) and lithiohexamethyleneimine (LHMI), and star‐shaped copoly(styrene–butadiene–isoprene) was obtained by anionic polymerization using preformed N‐M‐Li as initiator, tetramethylethlenediamine (TMEDA) as polar modifier, and cyclohexane as solvent. The microstructure and the glass–transition temperature (Tg) of copolymers were characterized by ¹H NMR and differential scanning calorimetry (DSC), respectively. It showed that the non‐1,4‐structure content and the Tg of copolymers increased with the increase of TMEDA dosage or the decrease of polymerization temperature; however, the effects of the initiator concentration and DVB dosage on them were not obvious. We also obtained the relationships between the non‐1,4‐structure content of copolymers and the Tg of copolymers respectively, and between the ln(T/Li) (TMEDA/N‐M‐Li, mole ratio) and the non‐1,4‐structure content of copolymers, as follows: Tg (°C) = 0.6258C_{non 1,4}?55.93 and C_{non 1,4} = 20.79 ln K+59.11, where K is T/Li value. Therefore on the basis of experimental results, we realize polymer design according to our practical requirements. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5848–5853, 2006     

Synthesis and mechanical properties of high impact polystyrene with in situ bulk polymerization toughened by one‐pot Nd‐based styrene–isoprene–butadiene terpolymer rubber

High impact polystyrene (HIPS) resins were obtained with in situ bulk polymerization toughened by styrene–isoprene–butadiene terpolymer rubber (SIBR). SIBR prepolymer was prepared through selective polymerization of styrene (St), isoprene (Ip), and butadiene (Bd) in St with [Nd]/[Al]/[Cl] catalyst. Nd‐based catalyst exhibited more favorable activity toward conjugated diene other than St, resulting in St solution of random SIBR with high cis‐1,4 stereoregularity and low St content, which was directly exposed to the free radical polymerization of St to generate HIPS. Effect of toughened rubber and the initiators [difunctional (D2) and trifunctional (T3)] were examined to attain HIPS possessing mechanical properties as follow: impact strength, 0.9–24.8 kJ/m²; tensile strength, 16.0–27.5 MPa; and elongation at break, 7.4–107.0%. Increasing SIBR matrix in HIPS improved the impact strength and decreased tensile strength. The fracture surface morphologies of HIPS specimens were studied by notched impact tests and scanning electron microscopy (SEM), illustrating that the incremental SIBR matrix presented synergistic toughening effect of crazing to enhance the ductile fracture behavior. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43979.     

Polymerization of 1,3‐dienes containing functional groups: 8. Free‐radical polymerization of 2‐triethoxysilyl‐ 1,3‐butadiene

The presence of a bulky substituent at the 2‐position of 1,3‐butadiene derivatives is known to affect the polymerization behavior and microstructure of the resulting polymers. Free‐radical polymerization of 2‐triethoxysilyl‐1,3‐butadiene ( 1 ) was carried out under various conditions, and its polymerization behavior was compared with that of 2‐triethoxymethyl‐ and other silyl‐substituted butadienes. A sticky polymer of high 1,4‐structure ( ) was obtained in moderate yield by 2,2′‐azobisisobutyronitrile (AIBN)‐initiated polymerization. A smaller amount of Diels–Alder dimer was formed compared with the case of other silyl‐substituted butadienes. The rate of polymerization (R_p) was found to be R_p = k[AIBN]^0.5[ 1 ]^1.2, and the overall activation energy for polymerization was determined to be 117 kJ mol^?1. The monomer reactivity ratios in copolymerization with styrene were r ₁ = 2.65 and r_st = 0.26. The glass transition temperature of the polymer of 1 was found to be ?78 °C. Free‐radical polymerization of 1 proceeded smoothly to give the corresponding 1,4‐polydiene. The 1,4‐E content of the polymer was less compared with that of poly(2‐triethoxymethyl‐1,3‐butadiene) and poly(2‐triisopropoxysilyl‐1,3‐butadiene) prepared under similar conditions. Copyright © 2010 Society of Chemical Industry     

Synthesis and characterization of star‐branched polyisobutylene with SIpS triblock copolymer core

Well‐defined polystyrene‐b‐polyisoprene‐b‐polystyrene (SIpS) triblock copolymers with different microstructures were synthesized by living anionic polymerization. The synthesis of star‐branched polyisobutylene (PIB) was accomplished by the cationic polymerization in 2‐chloro‐2,4,4‐trimethylpentane/titanium tetrachloride/SIpS triblock copolymer/2,6‐di‐tert‐butylpyridine initiating system. The double bonds in SIpS triblock copolymer were activated as starting points for isobutylene polymerization. The formation of star‐branched architecture was demonstrated by size‐exclusion chromatography with quadruple detection: refractive index, multiangle laser light scattering, viscometric, and ultraviolet detectors. SIpS triblock copolymer with high 3,4‐PIp content is more reactive than that with high 1,4‐PIp content in cationic initiating stage. The yields of star‐branched PIB were remarkably dependent on the reaction time of TMP⁺ with SIpS. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Cationic polymerization of isoprene using zinc halides as co‐initiators: towards well‐defined oligo(isoprene)s under mild conditions

The activity of ZnX₂‐based initiating systems (X = Cl, Br, I) in the cationic polymerization of isoprene was studied. The highest activity was achieved when co‐initiator (ZnX₂) was solubilized in a minimal amount of strongly coordinating solvent such as diethyl ether or acetone and when trichloroacetic acid was used as an initiator. It is shown that the polymerization rate increased in the series ZnI₂ < ZnCl₂ < ZnBr₂. An increase of initiator concentration and temperature also led to an increase of the polymerization rate. The obtained polyisoprenes did not contain high‐molecular‐weight and insoluble fractions and were characterized by low number‐average molecular weight and relatively narrow molecular weight distribution. Unsaturation of polyisoprene decreased with an increase of monomer conversion and reaction temperature. The unsaturated part of the polyisoprene chain possessed predominantly 1,4‐trans microstructure with regular and inverse addition, whereas the 1,2‐ and 3,4‐isomers were present as minor components. It is shown that the synthesized low‐molecular‐weight polyisoprenes are effective plasticizers for rubber compounds in the manufacture of tyres. © 2012 Society of Chemical Industry     

Phase‐transfer‐agent‐aided polymerization and graft copolymerization of acrylamide

The use of phase‐transfer catalysts, with water‐insoluble initiators, for polymerization and graft copolymerization reactions was explored. The polymerization of a water‐soluble vinyl monomer, acrylamide (AAm), and the graft copolymerization of AAm onto a water‐insoluble polymer backbone, isotactic polypropylene (IPP), with a water‐insoluble initiator, benzoyl peroxide (BPO), and a phase‐transfer catalyst, tetrabutyl ammonium bromide (Bu₄N⁺Br^?), were carried out in a water/xylene binary solvent system. The conversion percentage of AAm into polyacrylamide (PAAm) and the percentage of grafting of AAm onto IPP were determined as functions of various reaction parameters, such as the BPO, AAm, and phase‐transfer‐catalyst concentrations, the amounts of water and xylene in the water/xylene mixture, the time, and the temperature. The graft copolymer, IPP‐g‐PAAm, was characterized with IR spectroscopy and thermogravimetric analysis. By a comparison of the results of the phase‐transfer‐catalyzed graft copolymerization of AAm onto IPP and the preirradiation method, it was observed that the optimum reaction conditions were milder for the phase‐transfer‐catalyst‐aided graft copolymerization. Milder reaction conditions, including the temperature, the time of reaction, and a moderate initiator (BPO), in comparison with high‐energy γ‐rays, led to better quality products, and the reaction proceeded smoothly with high productivity. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2364–2375, 2004     

Composition and long‐term stability of polyglycidol prepared by cationic ring‐opening polymerization

Polyglycidol synthesized by cationic ring‐opening polymerization of glycidol (boron trifluoride initiation in dichloromethane) was purified of low molecular weight contaminants by centrifugal filtration. The high and low molecular weight fractions were characterized by NMR, GPC, osmometry, viscometry, DSC, and FTIR. The ¹³C‐NMR spectrum of this polymer was completely annotated by proposing a new step in the reaction mechanism. The four thermal dimers of glycidol were also isolated and identified as 2,5‐bis(hydroxymethyl)‐1,4‐dioxane and 2,6‐bis(hydroxymethyl)‐1,4‐dioxane, each of which can exist in cis and trans configurations. Polyglycidol was found to be hygroscopic, picking up about 5% by weight of atmospheric moisture. It was also found that, over time (ca. 1–2 years), polyglycidol crosslinks into a rubbery, insoluble mass. It is therefore recommended that this polymer be stored dry and used within a few months of synthesis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1344–1351, 2004     

Synthesis and chain extension of poly(L‐lactic acid‐co‐succinic acid‐co‐1,4‐butene diol)

L ‐Lactic acid (LA) was copolymerized with succinic acid (SA) and 1,4‐butenediol (1,4‐BED) in bulk state with titanium(IV) butoxide as a catalyst to produce poly(LA‐co‐SA‐co‐1,4‐BED) (PLASBED). Poly(L ‐lactic acid) (PLLA) homopolymer obtained from a direct condensation polymerization of LA had weight average molecular weight (M_w) less than 4.1 × 10⁴ and was too brittle to prepare specimens for the tensile test. Addition of SA and 1,4‐BED to LA produced PLASB with M_w as high as 1.4 × 10⁵ and exhibited tensile properties comparable to a commercially available high‐molecular‐weight PLLA. Chain extension by intermolecular linking reaction through the unsaturated 1,4‐BED units in PLASBED with benzoyl peroxide further increased the molecular weight and made PLASBED more ductile and flexible to show elongation at break as high as 450%. Biodegradability of PLASBED measured by the modified Sturm test was nearly independent of the 1,4‐BED content. Gel formation during the chain extension did not exert any significant influence on the biodegradability either. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1116–1121, 2005     

Binary copolymerization of 4‐methyl‐1,3‐pentadiene with styrene,butadiene and isoprene catalysed by a titanium [OSSO]‐type catalyst

Binary copolymerization of 4‐methyl‐1,3‐pentadiene (4MPD) with styrene, butadiene and isoprene promoted by the titanium complex dichloro{1,4‐dithiabutanediyl‐2,2′‐bis[4,6‐bis(2‐phenyl‐2‐propyl)phenoxy]}titanium activated by methylaluminoxane is reported. All the copolymers are obtained in a wide range of composition and the molecular weight distributions obtained from gel permeation chromatographic analysis of the copolymers are coherent with the materials being copolymeric in nature. The copolymer microstructure was fully elucidated by means of ¹H NMR and ¹³C NMR spectroscopy. Differential scanning calorimetry shows an increase of glass transition temperature (T_g) with the amount of 4MPD in the copolymers with butadiene and isoprene, while in the copolymers with styrene T_g is increased on increasing the amount of styrene. © 2016 Society of Chemical Industry     

Synthesis of a high‐trans 1,4‐butadiene/isoprene copolymers with supported titanium catalysts

The copolymerization of butadiene (Bd) and isoprene (Ip) with a supported titanium‐triisobutyl aluminum catalyst system was studied. An analysis using differential scanning calorimetry, X‐ray diffraction, and ¹³C‐NMR spectra indicated that products with 25–60 mol % Bd units were random copolymers and that the melting temperatures and glass‐transition temperatures (Tg) were 30–40 and ?74°C (or thereabout), respectively, which were very similar to those of natural rubber. The chemical structure of these copolymers was characterized by a high‐trans 1,4‐configuration: the trans 1,4‐content of Ip units was greater than 98%, and the trans 1,4‐content of Bd units was greater than 90%. The reactivity ratio of Bd was greater than that of Ip (r_Bd = 5.7 and r_Ip = 0.17). The sequence distribution of the monomer units of the copolymers followed a first‐order Markov statistical model. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1800–1807, 2003     

Synthesis and characterization of homo‐ and copolymers of 3‐(2‐cyano ethoxy)methyl‐ and 3‐[methoxy(triethylenoxy)]methyl‐3′‐methyl‐oxetane

Two oxetane‐derived monomers 3‐(2‐cyanoethoxy)methyl‐ and 3‐(methoxy(triethylenoxy)) methyl‐3′‐methyloxetane were prepared from the reaction of 3‐methyl‐3′‐hydroxymethyloxetane with acrylonitrile and triethylene glycol monomethyl ether, respectively. Their homo‐ and copolyethers were synthesized with BF₃· Et₂O/1,4‐butanediol and trifluoromethane sulfonic acid as initiator through cationic ring‐opening polymerization. The structure of the polymers was characterized by FTIR and¹H NMR. The ratio of two repeating units incorporated into the copolymers is well consistent with the feed ratio. Regarding glass transition temperature (T_g), the DSC data imply that the resulting copolymers have a lower T_g than pure poly(ethylene oxide). Moreover, the TGA measurements reveal that they possess in general a high heat decomposition temperature. The ion conductivity of a sample (P‐AN 20) is 1.07 × 10^?5 S cm^?1 at room temperature and 2.79 × 10^?4 S cm^?1 at 80 °C, thus presenting the potential to meet the practical requirement of lithium ion batteries for polymer electrolytes. Copyright © 2005 Society of Chemical Industry     

Biodegradable poly(ester‐ether)s: ring‐opening polymerization of D,L‐3‐methyl‐1,4‐dioxan‐2‐one using various initiator systems

The synthesis and detailed characterization of racemic 3‐methyl‐1,4‐dioxan‐2‐one (3‐MeDX) are reported. The bulk ring‐opening polymerization of 3‐MeDX, to yield a poly(ester‐ether) meant for biomedical applications, in the presence of various initiators such as tin(II) octanoate, tin(II) octanoate/n‐butyl alcohol, aluminium tris‐isopropoxide and an aluminium Schiff base complex (HAPENAlOⁱPr) under varying experimental conditions is here detailed for the first time. Polymerization kinetics were investigated and compared with those of 1,4‐dioxan‐2‐one. The studies reveal that the rate of polymerization of 3‐MeDX is less than that of 1,4‐dioxan‐2‐one. Experimental conditions to achieve relatively high molar masses have been established. Thermodynamic parameters such as enthalpy and entropy of 3‐MeDX polymerization as well as ceiling temperature have been determined. Poly(D ,L ‐3‐MeDX) is found to possess a much lower ceiling temperature than poly(1,4‐dioxan‐2‐one). Poly(D ,L ‐3‐MeDX) was characterized using NMR spectroscopy, matrix‐assisted laser desorption ionization mass spectrometry, size exclusion chromatography and differential scanning calorimetry. This polymer is an amorphous material with a glass transition temperature of about ?20 °C. Copyright © 2010 Society of Chemical Industry     

Preparation of poly(methyl methacrylate‐co‐butyl methacrylate) nanoparticles and their reinforcing effect on natural rubber

Poly(methyl methacrylate‐co‐butyl methacrylate) [P(MMA‐co‐BMA)] nanoparticles were synthesized via emulsion polymerization, and incorporated into natural rubber (NR) by latex compounding. Monodispersed, core‐shell P(MMA‐co‐BMA)/casein nanoparticles (abbreviated as PMBMA‐CA) were produced with casein (CA) as surfactant. The chemical structure of P(MMA‐co‐BMA) copolymers were confirmed by ¹H‐NMR and FTIR analyses. Transmission electron microscopy demonstrated the core–shell structure of PMBMA‐CA, and PMBMA‐CA homogenously distributed around NR particles, indicating the interaction between PMBMA‐CA and NR. As a result, the tensile strength and modulus of NR/PMBMA‐CA films were significantly enhanced. The tensile strength was increased by 100% with 10% copolymer addition, when the molar ratio of MMA:BMA was 8:2. In addition, scanning electron microscopy and atomic force microscopy results presented that the NR/PMBMA‐CA films exhibited smooth surfaces with low roughness, and PMBMA‐CA was compatible with NR. FTIR‐ATR analyses also suggested fewer PMBMA‐CA nanoparticles migrated out of NR. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43843.     

Synthesis and characterization of poly(p‐phenylene)‐graft‐poly(ε‐caprolactone) copolymers by combined ring‐opening polymerization and cross‐coupling processes

2,5‐Dibromo‐1,4‐(dihydroxymethyl)benzene was used as initiator in ring‐opening polymerization of ε‐caprolactone in the presence of stannous octoate (Sn(Oct)₂) catalyst. The resulting poly(ε‐caprolactone) (PCL) macromonomer, with a central 2,5‐dibromo‐1,4‐diphenylene group, was used in combination with 1,4‐dibromo‐2,5‐dimethylbenzene for a Suzuki coupling in the presence of Pd(PPh₃)₄ as catalyst or using the system NiCl₂/bpy/PPh₃/Zn for a Yamamoto‐type polymerization. The poly(p‐phenylenes) (PPP) obtained, with PCL side chains, have solubility properties similar to those of the starting macromonomer, ie soluble in common organic solvents at room temperature. The new polymers were characterized by ¹H and ¹³C NMR and UV spectroscopy and also by GPC measurements. The thermal behaviour of the precursor PCL macromonomer and the final poly(p‐phenylene)‐graft‐poly(ε‐caprolactone) copolymers were investigated by thermogravimetric analysis and differential scanning calorimetry analyses and compared. Copyright © 2004 Society of Chemical Industry     

ABS modified with hydrogenated polystyrene‐grafted‐natural rubber

Natural rubber (NR) latex was grafted by emulsion polymerization with styrene monomer, using cumene hydroperoxide/tetraethylene pentamene as redox initiator system. The polystyrene‐grafted NR (PS‐g‐NR) was hydrogenated by diimide reduction in the latex form using hydrazine and hydrogen peroxide with boric acid as a promoter. At the optimum condition for graft copolymerization, a grafting efficiency of 81.5% was obtained. In addition, the highest hydrogenation level of 47.2% was achieved using a hydrazine:hydrogen peroxide molar ratio of 1:1.1. Hydrogenation of the PS‐g‐NR (H(PS‐g‐NR)) increased the thermal stability. Transmission electron microscopy analysis of the H(PS‐g‐NR) particles revealed a nonhydrogenated rubber core and hydrogenated outer rubber layer, in accordance with the layer model. The addition of H(PS‐g‐NR) at 10 wt % as modifier in an acrylonitrile–butadiene–styrene (ABS) copolymer increased the tensile and impact strengths and the thermal resistance of the ABS blends, and to a greater extent than that provided by blending with NR or PS‐g‐NR. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation,characterization, and flocculation performance of P(acrylamide‐co‐diallyldimethylammonium chloride) by UV‐initiated template polymerization

This study prepared TPDA, a high‐intrinsic‐viscosity cationic polyacrylamide, through ultraviolet (UV)‐initiated template polymerization. Acrylamide (AM) and diallyldimethylammonium chloride (DMD) served as monomers, and poly sodium polyacrylate (PAAS) served as the template. The structure of TPDA was characterized by Fourier‐transform infrared spectroscopy, proton nuclear magnetic resonance spectroscopy, and thermogravimetric analysis. The synthetic conditions of TPDA were studied and optimized by single‐factor experiments. An optimized product was obtained at an intrinsic viscosity of 11.3 dL g^?1 and a conversion rate of 97.2% with a total monomer concentration of 20%, DMD concentration of 30%, initiator concentration of 0.045%, pH of 8, EDTA concentration of 0.3%, and UV irradiation of 90 min. Results showed that TPDA was the copolymer of AM and DMD with a micro‐block structure at the molecular chain. Given its high intrinsic viscosity and cationic block structure, TPDA performed better in kaolin flocculation than that prepared without template addition. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41747.     

Stereocontrolled Synthesis and Pharmacological Evaluation of Azetidine‐2,3‐Dicarboxylic Acids at NMDA Receptors

The four stereoisomers of azetidine‐2,3‐dicaroxylic acid (L ‐trans‐ADC, L ‐cis‐ADC, D ‐trans‐ADC, and D ‐cis‐ADC) were synthesized in a stereocontrolled fashion following two distinct strategies: one providing the two cis‐ADC enantiomers and one giving access to the two trans‐ADC enantiomers. The four azetidinic amino acids were characterized in a radioligand binding assay ([³H]CGP39653) at native NMDA receptors: L ‐trans‐ADC showed the highest affinity (K_i=10 μM ) followed by the D ‐cis‐ADC stereoisomer (21 μM ). In contrast, the two analogues L ‐cis‐ADC and D ‐trans‐ADC were low‐affinity ligands (>100 and 90 μM , respectively). Electrophysiological characterization of the ADC compounds at the four NMDA receptor subtypes NR1/NR2A, NR1/NR2B, NR1/NR2C, and NR1/NR2D expressed in Xenopus oocytes showed that L ‐trans‐ADC displayed the highest agonist potency at NR1/NR2D (EC₅₀=50 μM ), which was 9.4‐, 3.4‐, and 1.9‐fold higher than the respective potencies at NR1/NR2A–C. D ‐cis‐ADC was shown to be a partial agonist at NR1/NR2C and NR1/NR2D with medium‐range micromolar potencies (EC₅₀=720 and 230 μM , respectively). A subsequent in silico ligand–protein docking study suggested an unusual binding mode for these amino acids in the agonist binding site.