Dielectric behaviour and relaxation in poly(propylene glycol)–water mixtures studied by time domain reflectometry

Dielectric behaviour of poly(propylene glycol) (PPG) of number‐average molecular weight 2000 g mol^?1 and binary mixtures of PPG with water (PPG–W) of various concentrations were carried out in the frequency range 10 MHz to 4 GHz at 25 °C. The dielectric dispersion and absorption curves related to the orientational motion of these molecules in the binary mixtures are described by a single relaxation time using Debye's model. The values of static dielectric constant ε_o, high frequency limiting dielectric constant ε_∞, and dielectric relaxation time τ_o were determined for PPG and PPG–W mixtures. The values of the dielectric parameters were used to explore the nature of homogeneous and heterogeneous dynamic networks formed through hydrogen bonding in the binary mixtures of PPG and water molecules with concentration variation. The dielectric studies of PPG molecules were also carried out in the same frequency range at four temperatures, namely 25, 35, 45 and 55 °C. The temperature‐dependent relaxation times were used to evaluate the thermodynamical parameters for the dielectric relaxation processes. The dielectric relaxation free energy of activation ΔF_τ for PPG molecules was found in the range ～4.5 to 4.7 kcal mol^?1, which corresponds to the activation energy needed for the breakage of hydrogen bonds. Furthermore, the large negative value of the entropy ΔS_τ of PPG molecules confirms that the configuration involved in dipolar orientation has an activated state, which is more ordered than in the normal state. Copyright © 2004 Society of Chemical Industry     

Dielectric properties of low molecular weight poly(ethylene glycol)s

This paper reports the measured values of dielectric permittivity ε′ and dielectric loss ε″ of ethylene glycol, diethylene glycol and poly(ethylene glycol)s of average molecular weight 200, 300, 400 and 600 g mol⁻¹ in the pure liquid state. The measurements have been carried out in the frequency range 200 MHz to 20 GHz at four different temperatures of 25, 35, 45 and 55 °C. The complex plane plots (ε″ versus ε′) of these molecules are Cole–Cole arcs. The static dielectric constant ε₀, high‐frequency limiting dielectric constant ε_∞, average relaxation time τ₀ and distribution parameter α have been determined from these plots. The value of the Kirkwood correlation factor g and the dielectric rate free energy of activation ΔF have also been evaluated. The dependence of relaxation time on molecular size and viscosity has been discussed. A comparison has also been made with the dielectric behaviour of these molecules in dilute solutions of non‐polar solvents, which were carried out earlier in this laboratory. The influences of intermolecular hydrogen bonding and molecular chain coiling on the dielectric relaxation of these molecules have been recognized. © 2000 Society of Chemical Industry     

Thermal and spectroscopic studies of poly(N‐vinyl pyrrolidone)/poly(vinyl alcohol) blend films

Poly(N‐vinyl pyrrolidone) (PVP) and poly (vinyl alcohol) (PVA) homopolymers and their blended samples with different compositions were prepared using cast technique and subjected to X‐ray diffraction (XRD) measurements, infrared (IR) spectroscopy, ultraviolet/visible spectroscopy, and thermogravimetric analysis (TGA). XRD patterns of homopolymers and their blended samples indicated that blending amorphous materials, such as PVP, with semicrystalline polymer, such as PVA, gives rise to an amorphous structure with two halo peaks at positions identical to those found in pure PVP. Identification of structure and assignments of the most evident IR ‐ absorption bands of PVP and PVA as well as their blends in the range 400–2000 cm^?1 were studied. UV–vis spectra were used to study absorption spectra and estimate the values of absorption edge, E_g, and band tail, E_e, for all samples. Making use of Coats‐Redfern relation, thermogravimetric (TG) data allowed the calculation of the values of some thermodynamic parameters, such as activation energy E, entropy ΔS^#, enthalpy ΔH, and free energy of activation ΔG^# for different decomposition steps in the samples under investigation. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Syntheses and adsorption properties for Hg2+ of chelating resin of crosslinked polystyrene‐supported 2,5‐dimercapto‐1,3,4‐thiodiazole

A novel chelating resin with functional group containing S and N atoms was prepared using chloromethylated polystyrene and 2,5‐dimercapto‐1,3,4‐thiodiazole (also called bismuththiol I, BMT) as materials. Its structure was characterized by infrared spectra and elementary analysis. The results showed that the content of the functional group was 2.07 mmol BMT g^?1 resin, 47% of which were in the form of monosubstitution (PS‐BMT‐1) and 53% in the form of double substitution (PS‐BMT‐2). The adsorption for mercury ion was investigated. The adsorption dynamics showed that the adsorption was controlled by liquid film diffusion. Increasing the temperature was beneficial to adsorption. The Langmuir model was much better than the Freundlich model to describe the isothermal process. The adsorption activation energy (E_a), ΔG, ΔH, and ΔS values calculated were 18.56 kJ·mol^?1, ‐5.99 kJ·mol^?1, 16.38 kJ·mol^?1, and 37.36, J·mol^?1·K^?1, respectively. The chelating resin could be easily regenerated by 2% thiourea in 0.1 mol·L^?1 HCl with higher effectiveness. Five adsorption–desorption cycles demonstrated that this resin was suitable for repeated use without considerable change in adsorption capacity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1646–1652, 2004     

Kinetic study of ytterbium(III) extraction from sulfate medium with Cyanex 923

The kinetics of ytterbium(III) extraction from sulfate medium with Cyanex 923 in heptane has been investigated with a constant interfacial cell with laminar flow, which aimed to identify the extraction regime, reaction zone and rate equations. It was found that the extraction rate of ytterbium(III) increased linearly with stirring speed and specific interfacial area. The activation energy E_a (9.56 kJ mol^?1), activation enthalpy ΔH^± (7.05 kJ mol^?1), activation entropy ΔS^±₂₉₈ (?0.31 kJ mol^?1) and Gibbs free energy of activation ΔG^±₂₉₈ (98.3 kJ mol^?1) were calculated from the dependence of extraction rate on temperature. The experiential rate equations were obtained by investigating the influence of the concentration of various species on the extraction rate. A diffusion regime has been deduced from evidence of the linear dependence of extraction rate on stirring speed and the low value of the activation energy. The liquid–liquid interface is most probably the reaction zone in view of the linear dependence of extraction rate on specific interfacial area, the high interfacial activity and low water‐solubility of extractant. Thus the mass transfer rate is controlled by interfacial film diffusion of species. Copyright © 2007 Society of Chemical Industry     

Studies on two‐dimensional coordination polymer cadmium phosphate and its high efficient adsorption of Pb(II) ions from aqueous solutions

The two‐dimensional coordination polymer cadmium phosphate with the morphology of rectangle layers was prepared by solid‐state template reaction at room temperature, and was characterized by XRD, FTIR, and TEM techniques. The as‐synthesized sample is a layered cadmium phosphate material, in which the structure is poly (CdPO₄^?) anion framework with ammonium ions and water species residing in the space between the layers, and cadmium ions are coordinated by the phosphate oxygen atoms. This article also presents the adsorption of Pb(II) ions from aqueous solution on the as‐synthesized coordination polymer cadmium phosphate, and the results showed that this inorganic polymer adsorbent had good adsorption capacity. It could reach to the saturation adsorption capacity within an hour, and its excellent adsorption capacity for Pb(II) was 5.50 mmol/g when the initial solution concentration was 1.68 × 10³ μg/mL at T = 278K. Moreover, the adsorption kinetics and adsorption isotherms were studied, it revealed that the adsorption kinetics can be modeled by pseudo second‐order rate equation wonderfully. The apparent activation energy (E_a), ΔG, ΔH, and ΔS were 3.16 kJ mol^?1, ?13.97 kJ mol^?1, ?11.84 kJ mol^?1, and 7.66 J mol^?1 K^?1, respectively. And it was found that Langmuir equation could well interpret the adsorption of the as‐synthesized coordination polymer cadmium phosphate for Pb(II) ions. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Microwave dielectric relaxation study of poly(propylene glycol) in dilute solution

Dielectric relaxation studies of poly(propylene glycol), average molecular weight 2000 g mol⁻¹, in dilute solution of cyclohexane, decaline, benzene and carbon tetrachloride have been carried out at 10.10 GHz and 35 °C. Average relaxation time τ₀, and relaxation times corresponding to segmental motion τ₁, group rotations τ₂ and dipole moment µ have been determined. It is found that τ₀, τ₁ and µ are influenced by the solvent environment while the τ₂ value is solvent‐independent. A comparison has been made with the dielectric behaviour of poly(ethylene glycol), average molecular weight 1500 g mol⁻¹, in dilute solutions of benzene and carbon tetrachloride because both systems have an equal number of monomer units. The effect of methyl side‐groups on dielectric relaxation in poly(propylene glycol) molecules is discussed. The Kirkwood correlation factor is also evaluated in dilute solutions with concentration variation and it is found that these molecules exist in cluster form due to intermolecular hydrogen bonding. © 2000 Society of Chemical Industry     

Effect of Temperature on Kinetics and Adsorption Profile of Endothermic Chemisorption Process: –Tm(III)–PAN Loaded PUF System

Abstract

The sorption behavior of 3.18×10^?6 mol l^?1 solution of Tm(III) metal ions onto 7.25 mg l^?1 of 1‐(2‐pyridylazo)‐2‐naphthol (PAN) loaded polyurethane foam (PUF) has been investigated at different temperatures i.e. 303 K, 313 K, and 323 K. The maximum equilibration time of sorption was 30 minutes from pH 7.5 buffer solution at all temperatures. The various rate parameters of adsorption process have been investigated. The diffusional activation energy (ΔE_ads) and activation entropy (ΔS_ads) of the system were found to be 22.1±2.6 kJ mol^?1 and 52.7±6.2 J mol^?1 K^?1, respectively. The thermodynamic parameters such as enthalpy (ΔH), entropy (ΔS), and Gibbs free energy (ΔG) were calculated and interpreted. The positive value of ΔH and negative value of ΔG indicate that sorption is endothermic and spontaneous in nature, respectively. The adsorption isotherms such as Freundlich, Langmuir, and Dubinin–Radushkevich isotherm were tested experimentally at different temperatures. The changes in adsorption isotherm constants were discussed. The binding energy constant (b) of Langmuir isotherm increases with temperature. The differential heat of adsorption (ΔH_diff), entropy of adsorption (ΔS_diff) and adsorption free energy (ΔG_ads) at 313 K were determined and found to be 38±2 kJ mol^?1, 249±3 J mol^?1 K^?1 and –40.1±1.1 kJ mol^?1, respectively. The stability of sorbed complex and mechanism involved in adsorption process has been discussed using different thermodynamic parameters and sorption free energy.     

Kinetics of thermal inactivation of transglutaminase from a newly isolated Bacillus circulans BL32

BACKGROUND: This paper describes the modeling of the kinetics of thermal inactivation of transglutaminase (TGase) from a newly isolated Bacillus circulans BL32, isolated from the Amazon environment. The purified enzyme was incubated at temperatures ranging from 30 to 70 °C and values of the thermodynamic inactivation parameters, such as activation energy (ΔE), activation enthalpy (ΔH), activation entropy (ΔS), and free energy (ΔG) for thermal inactivation, were calculated. RESULTS: The kinetics of TGase thermo‐inactivation followed a Lumry–Eyring model. The enzyme was very stable up to 50 °C, with approximately 50% of activity remaining after heating for 12 h. It was completely inactivated by incubation at 70 °C for 2 min. ΔE for TGase was 350.5 kJ mol^?1. ΔH and ΔS for thermo‐inactivation of the TGase were 347.8 kJ mol^?1 and 744 J mol^?1 K^?1 at 50 °C, respectively. Dynamic light scattering measurements suggest that the thermal inactivation of this microbial TGase can be partially attributed to the formation of aggregates. CONCLUSION: These results provide useful information about the thermal characteristics of the microbial TGase from B. circulans BL32 and indicate that this enzyme could be a good candidate for industrial applications. Copyright © 2009 Society of Chemical Industry     

Fumed SiO2 nanoparticle reinforced biopolymer blend nanocomposites with high dielectric constant and low dielectric loss for flexible organic electronics

In the present study, fumed silica (SiO₂) nanoparticle reinforced poly(vinyl alcohol) (PVA) and poly(vinylpyrrolidone) (PVP) blend nanocomposite films were prepared via a simple solution‐blending technique. Fourier transform infrared spectroscopy (FTIR), ultraviolet–visible spectroscopy (UV–vis), X‐ray diffraction (XRD), and scanning electron microscopy (SEM) were employed to elucidate the successful incorporation of SiO₂ nanoparticles in the PVA/PVP blend matrix. A thermogravimetric analyzer was used to evaluate the thermal stability of the nanocomposites. The dielectric properties such as dielectric constant (?) and dielectric loss (tan δ) of the PVA/PVP/SiO₂ nanocomposite films were evaluated in the broadband frequency range of 10^?2 Hz to 20 MHz and for temperatures in the range 40–150 °C. The FTIR and UV–vis spectroscopy results implied the presence of hydrogen bonding interaction between SiO₂ and the PVA/PVP blend matrix. The XRD and SEM results revealed that SiO₂ nanoparticles were uniformly dispersed in the PVA/PVP blend matrix. The dielectric property analysis revealed that the dielectric constant values of the nanocomposites are higher than those of PVA/PVP blends. The maximum dielectric constant and the dielectric loss were 125 (10^?2 Hz, 150 °C) and 1.1 (10^?2 Hz, 70 °C), respectively, for PVA/PVP/SiO₂ nanocomposites with 25 wt % SiO₂ content. These results enable the preparation of dielectric nanocomposites using a facile solution‐casting method that exhibit the desirable dielectric performance for flexible organic electronics. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44427.     

Solubility of polystyrene with various molecular weights in subcritical 1,1,1,2‐tetrafluoroethane: experiment and modified model

The solubility of polystyrene with molecular weight of 100 000 and 260 000 g mol^?1 was measured at temperatures from 313 to 333 K and at pressures from 5.0 to 13.0 MPa in subcritical 1,1,1,2‐tetrafluoroethane (R134a). The effects of pressure, temperature and molecular weight on the solubility of polystyrene were investigated. Meanwhile, the solubility of polystyrene was correlated using six density‐based semi‐empirical models (Chrastil, A‐L, K‐J, S‐S, M‐S‐T and Bartle). The M‐S‐T model was used to verify the self‐consistency of the experimental data, and the enthalpy values of polystyrene, including ΔH_total, ΔH_sub and ΔH_sol, were estimated through the Chrastil and Bartle models. In addition, a modified M‐S‐T model was proposed through a detailed study of semi‐empirical model formulas and verified by the solubility of polystyrene in subcritical R134a and 38 other solid solutes in supercritical carbon dioxide and subcritical R134a. © 2018 Society of Chemical Industry     

Synergistic extraction of rare earths(III) from chloride medium with mixtures of 1‐phenyl‐3‐methyl‐4‐benzoyl‐pyrazalone‐5 and di‐(2‐ethylhexyl)‐2‐ethylhexylphosphonate

The synergistic effect of 1‐phenyl‐3‐methyl‐4‐benzoyl‐pyrazalone‐5 (HPMBP, HA) and di‐(2‐ethylhexyl)‐2‐ethylhexylphosphonate (DEHEHP, B) in the extraction of rare earths (RE) from chloride solutions has been investigated. Under the experimental conditions used, there was no detectable extraction when DEHEHP was used as a single extractant while the amount of RE(III) extracted by HPMBP alone was also low. But mixtures of the two extractants at a certain ratio had very high extractability for all the RE(III). For example, the synergistic enhancement coefficient was calculated to be 9.35 for Y³⁺, and taking Yb³⁺ and Y³⁺ as examples, RE³⁺ is extracted as RE(OH)A₂.B. The stoichiometry, extraction constants and thermodynamic functions such as Gibbs free energy change ΔG (?17.06 kJ mol^?1), enthalpy change ΔH (?35.08 kJ mol^?1) and entropy change ΔS (?60.47 J K^?1 mol^?1) for Y³⁺ at 298 K were determined. The separation factors (SF) for adjacent pairs of rare earths were calculated. Studies show that the binary extraction system not only enhances the extraction efficiency of RE(III) but also improves the selectivity, especially between La(III) and the other rare earth elements. Copyright © 2006 Society of Chemical Industry     

Synthesis,characterization, conductivity,band gap,and kinetic of thermal degradation of poly‐4‐[(2‐mercaptophenyl) imino methyl] phenol

The oxidative polycondensation reaction conditions of 4‐[(2‐mercaptophenyl) imino methyl] phenol (2‐MPIMP) were studied in an aqueous acidic medium between 40 and 90°C by using oxidants such as air, H₂O₂, and NaOCl. The structures of the synthesized monomer and polymer were confirmed by FTIR, ¹H NMR, ¹³C NMR, and elemental analysis. The characterization was made by TGA‐DTA, size exclusion chromatography (SEC) and solubility tests. At the optimum reaction conditions, the yield of poly‐4‐[(2‐mercaptophenyl) imino methyl]phenol (P‐2‐MPIMP) was found to be 92% for NaOCl oxidant, 84% for H₂O₂ oxidant 54% for air oxidant. According to the SEC analysis, the number‐average molecular weight (M_n), weight‐average molecular weight (M_w), and polydispersity index values of P‐2‐MPIMP were found to be 1700 g mol^?1, 1900 g mol^?1, and 1.118, using H₂O₂; 3100 g mol^?1, 3400 g mol^?1, and 1.097, using air; and 6750 g mol^?1, 6900 g mol^?1, and 1.022, using NaOCl, respectively. According to TG analysis, the weight losses of 2‐MPIMP and P‐2‐MPIMP were found to be 95.93% and 76.41% at 1000°C, respectively. P‐2‐MPIMP showed higher stability against thermal decomposition. Also, electrical conductivity of the P‐2‐MPIMP was measured, showing that the polymer is a typical semiconductor. The highest occupied molecular orbital, the lowest unoccupied molecular orbital, and the electrochemical energy gaps (E′_g) of 2‐MPIMP and P‐2‐MPIMP were found to be ?6.13, ?6.09; ?2.65, ?2.67; and 3.48, 3.42 eV, respectively. Kinetic and thermodynamic parameters of these compounds investigated by MacCallum‐Tanner and van Krevelen methods. The values of the apparent activation energies of thermal decomposition (E_a), the reaction order (n), pre‐exponential factor (A), the entropy change (ΔS*), enthalpy change (ΔH*), and free energy change (ΔG*) were calculated from the TGA curves of compounds. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Biodegradable blends based on polyvinyl pyrrolidone for insulation purposes

Polyvinyl pyrrolidone/polyvinyl alcohol (PVP/PVA) and polyvinyl pyrrolidone/starch (PVP/St) blends were prepared with different compositions. The compatibility studies indicate that PVP/PVA is compatible while PVP/St is incompatible. The addition of glycerol and glutaraldehyde can improve to some extent the phase separation behavior between PVP and St. The permittivity ε′ and the dielectric loss ε″ were measured in the frequency range 0.01 Hz up to 10 MHz and temperatures from 30 up to 90°C. It is found that the blend ratio (50/50) of both investigated systems is preferable for insulation purposes in comparable with the other blends under investigation. The data of the loss electric modulus M″ was calculated from the dielectric parameters ε′ and ε″and analyzed into three relaxation mechanisms ascribing the cooperative motion of the main and side chains τ₁ (αβ), the side chain motion τ₂ (β) and the segmental motion of the groups attached to the side chains τ₃ (βγ). The activation energy corresponds to the second relaxation process ΔH₂ was calculated using Arrhenius equation and found to be in the range which justifies the presumption of β‐relaxation process. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Dielectric relaxation and molecular dynamics in poly(vinyl pyrrolidone)-ethyl alcohol mixtures in pure liquid state and in non-polar solvent

Dielectric relaxation and molecular dynamics in poly(vinyl pyrrolidone)-ethyl alcohol (PVP-E) mixtures with varying concentration in pure state and also in very dilute solutions of benzene were studied for their molecular conformation at 35 °C. Dielectric permittivity ε′ and dielectric loss ε″ of PVP-E mixtures were measured by a time domain reflectometry technique in the frequency range 10 MHz to 10 GHz. The value of static dielectric constant ε₀, dielectric relaxation time τ, and dielectric free energy of activation ΔF_τ has been evaluated by fitting the complex dielectric data into Debye equation. The variation in ε₀ was discussed by considering the volume effect and the structuring effects of the PVP on ethyl alcohol molecules. The formation of cooperative domains between PVP and ethyl alcohol molecules, CD_PVP-E and between the ethyl alcohol-ethyl alcohol molecules CD_E and their dynamics in the PVP-E mixtures were explored by using the evaluated values of τ and ΔF_τ.The PVP-E mixtures of low PVP concentration were also studied in very dilute solutions of benzene at 10.1 GHz. The value of average relaxation time τ₀, distribution parameter α, and relaxation time corresponding to the motion of small multimer species of alcohol molecules τ₁ and group rotation τ₂ has been determined. It has been observed that in dilute solution of benzene the value of τ₀ and τ₁ increases with the increase in concentration of PVP in PVP-E mixture but the τ₂ value is found independent of the mixture constituent concentration. The entanglement of the CD_PVP-E and the increase in the length of CD_E in dilute solution of benzene due to dissociation of the complexes between carbonyl and hydroxyl groups has been explored. The value of τ₂ is assigned to the rotation of -OH group about C-O bond in the ethyl alcohol species in dynamic equilibrium with larger steric hindrance due to hydrogen bonding.     

Evaluation of a new water‐compatible hybrid molecularly imprinted polymer combined with restricted access for the selective recognition of folic acid in binding assays

This article deals with the synthesis of an organic?inorganic hybrid molecularly imprinted poly(methacrylic acid‐trimethylolpropane trimethacrylate)/SiO₂ combined with restricted access. Fourier Transform Infrared Spectroscopy, Transmission Electron Microscopy, Thermogravimetric Analysis, and textural data were used to characterize the structure of material. Higher selectivity was obtained for the molecularly imprinted polymer with restricted access when compared to nonimprinted polymer with restricted access, confirming the imprinting effect. The folic acid sorption for the polymers molecularly imprinted with restricted access, nonimprinted with restricted access, and molecularly imprinted, exhibited the following values of 5.6, 4.5, and 4.8 mg g^?1, respectively. Kinetic experimental data were very well adjusted to Elovich and pseudo‐second‐order models, which suggest that the sorption of folic acid takes place in binding sites with different energies. The obtained values of enthalpy, entropy and Gibbs free energy of ?12.79 kJ mol^?1, ?36.38 K^?1 J mol^?1, and ?1.76 kJ mol^?1, respectively, showed that the sorption of folic acid onto molecularly imprinted polymer combined with restricted access occurs spontaneously, is of both exothermic and of physical nature with an increase of ordering at the solid?solution interface. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43463.     

Adsorptive removal of anionic and non‐ionic surfactants from aqueous phase using Posidonia oceanica (L.) marine biomass

BACKGROUND: In this study, the capability of low‐cost, renewable and abundant marine biomass Posidonia oceanica (L.) for adsorptive removal of anionic and non‐ionic surfactants from aqueous solutions have been carried out in batch mode. Several experimental key parameters were investigated including exposure time, pH, temperature and initial surfactant concentration. RESULTS: It was found that the highest surfactant adsorption capacities reached at 30 °C were determined as 2.77 mg g^?1 for anionic NaDBS and as 1.81 mg g^?1 for non‐ionic TX‐100, both at pH 2. The biosorption process was revealed as a thermo‐dependent phenomenon. Equilibrium data were well described by the Langmuir isotherm model, suggesting therefore a homogeneous sorption surface with active sites of similar affinities. The thermodynamic constants of the adsorption process (i.e. ΔG°, ΔH° and ΔS°) were respectively evaluated as ? 8.28 kJ mol^?1, 48.07 kJ mol^?1 and ? 42.38 J mol^?1 K^?1 for NaDBS and ? 9.67 kJ mol^?1, 95.13 kJ mol^?1 and ? 174.09 J mol^?1 K^?1 for TX‐100. CONCLUSION: Based on this research, valorization of highly available Posidonia oceanica biomass, as biological adsorbent to remove anionic and non‐ionic surfactants, seems to be a promising technique, since the sorption systems studied were found to be favourable, endothermic and spontaneous. Copyright © 2007 Society of Chemical Industry     

Structural and Preliminary Explosive Property Characterizations of New 3,4,5‐Triamino‐1,2,4‐triazolium (Guanazinium) Salts

Two new highly stable energetic salts were synthesized in reasonable yield by using the high nitrogen‐content heterocycle 3,4,5‐triamino‐1,2,4‐triazole and resulting in its picrate and azotetrazolate salts. 3,4,5‐Triamino‐1,2,4‐triazolium picrate (1) and bis(3,4,5‐triamino‐1,2,4‐triazolium) 5,5′‐azotetrazolate (2) were characterized analytically and spectroscopically. X‐ray diffraction studies revealed that protonation takes place on the nitrogen N1 (crystallographically labelled as N2). The sensitivity of the compounds to shock and friction was also determined by standard BAM tests revealing a low sensitivity for both. B3LYP/6–31G(d, p) density functional (DFT) calculations were carried out to determine the enthalpy of combustion (Δ_cH (1) =−3737.8 kJ mol⁻¹, Δ_cH (2) =−4577.8 kJ mol⁻¹) and the standard enthalpy of formation (Δ_fH° (1) =−498.3 kJ mol⁻¹, (Δ_fH° (2) =+524.2 kJ mol⁻¹). The detonation pressures (P (1) =189×10⁸ Pa, P (2) =199×10⁸ Pa) and detonation velocities (D (1) =7015 m s⁻¹, D (2) =7683 m s⁻¹) were calculated using the program EXPLO5.     

Kinetic and Thermodynamic Studies of Emulsion Polymerization of a Sugar Monomer by Calorimetry with Compensation Heating and Differential Cooling

The kinetic and thermodynamic features of free‐radical batch emulsion polymerization of a sugar monomer (3‐MDG) and butyl acrylate (BA) were investigated in a power compensation calorimeter. The homopolymerizations as well as the copolymerization have been studied. The overall activation energy of 3‐MDG homopolymerization was 140 ± 3.8 kJ · mol^?1, the polymerization enthalpy was ΔH_MDG = ?51.6 ± 1.9 kJ · mol^?1 and the calculated adiabatic temperature rise was ΔT_ad = 78.5 K. The effects of the initiator and the emulsifier concentrations on the 3‐MDG/BA batch copolymerization kinetics and on the colloidal properties of the final sugar latexes were studied at 60 °C. At higher emulsifier and initiator concentration, respectively, the polymerization rate increases and the particle size decreases, but the trends do not conform to the Smith‐Ewart theory. Polydisperse sugar latex particles with a mean diameter in the range of 50–67 nm were obtained.

Relationship between the activation energy and the conversion for BA (open symbols) and 3‐MDG (solid symbols).     

Non‐isothermal crystallization behavior of stereo diblock polylactides with relatively short poly(d‐lactide) segments from the melt

Stereo diblock polylactides (SDB‐PLAs) composed of relatively short poly(d ‐lactide) (PDLA) segments and relatively long poly(l ‐lactide) (PLLA) segments were synthesized to have a wide number‐average molecular weight (M_n) range of 2.5 × 10⁴–2.0 × 10⁵ g mol^?1 and d ‐lactyl unit content of 0.9–38.6%. The effects of incorporated short PDLA segments (M_n = 2.0 × 10³–7.7 × 10³ g mol^?1) on crystallization behavior of the SDB‐PLAs were first investigated during heating after complete melting and quenching or during slow cooling after complete melting. Stereocomplex (SC) crystallites can be formed at d ‐lactyl unit content as low as 4.3 and 5.8% for heating and slow cooling, respectively, and for M_n of PDLA segments as low as 2.0 × 10³ and 3.5 × 10³ g mol^?1, respectively. With decreasing M_n and increasing d ‐lactyl unit content, the cold crystallization temperature during heating decreased and the crystallization temperature during slow cooling increased. With increasing d ‐lactyl unit content, the melting enthalpy (ΔH_m) of SC crystallites during heating and the crystallinity (X_c) of SC crystallites after slow cooling increased, whereas ΔH_m of PLLA homo‐crystallites during heating and X_c of PLLA homo‐crystallites after slow cooling decreased. The total ΔH_m of SC crystallites and PLLA homo‐crystallites during heating and the total X_c after slow cooling became a minimum at d ‐lactyl unit content of 10–15% and gave a maximum at d ‐lactyl unit content of 0%. Despite the accelerated crystallization of some of SDB‐PLAs, the low values of total ΔH_m and X_c at d ‐lactyl unit content of 10–15% are attributable to the formation of two crystalline species of SC crystallites and PLLA homo‐crystallites.