Rapid synthesis of ordered hexagonal mesoporous silica and their incorporation with Ag nanoparticles by solution plasma

Rapid synthesis of silica with ordered hexagonal mesopore arrangement was obtained using solution plasma process (SPP) by discharging the mixture of P123 triblock copolymer/TEOS in acid solution. SPP, moreover, was utilized for Ag nanoparticles (AgNPs) incorporation in silica framework as one-batch process using silver nitrate (AgNO₃) solution as precursor. The turbid silicate gel was clearly observed after discharge for 1 min and the white precipitate formed at 3 min. The mesopore with hexagonal arrangement and AgNPs were observed in mesoporous silica. Two regions of X-ray diffraction patterns (2θ < 2° and 2θ = 35–90°) corresponded to the mesoporous silica and Ag nanocrystal characteristics. Comparing with mesoporous silica prepared by a conventional sol–gel route, surface area and pore diameter of mesoporous silica prepared by solution plasma were observed to be larger. In addition, the increase in Ag loading resulted in the decrease in surface area with insignificant variation in the pore diameter of mesoporous silica. SPP could be successfully utilized not only to enhance gelation time but also to increase surface area and pore diameter of mesoporous silica.     

The preparation of Ag/mesoporous silica by direct silver reduction and Ag/functionalized mesoporous silica by in situ formation of adsorbed silver

Mesoporous silica (MS) with large pores and thiol functionalized mesoporous silica (TFMS) were synthesized. ²⁹Si MAS NMR confirmed the functionalization of MPTMS on the surface of mesoporous silica. Silver nanoparticles were prepared by two methods: (1) direct reduction of Ag⁺ ions with NaBH₄ in aqueous AgNO₃ solution containing MS, (2) in situ reduction of Ag⁺ ions adsorbed on TFMS with NaBH₄. The characteristics of products from both methods were compared using SAXRD, TEM, and N₂ adsorption-desorption. Ag nanoclusters were mostly confined and dispersed in the channels of the TFMS and their sizes were under 6 nm. However, Ag nanoparticles on the MS formed outside the mesoporous channels rather than within them.     

Solution plasma for template removal in mesoporous silica: pH and discharge time varying characteristics

The evaluation of the ability of solution plasma process, SPP, depending on the pH of the discharge solution and discharge time for template removal in mesoporous silica was described. In the synthesis of mesoporous silica, ternary surfactant system containing tri-block copolymer EO₂₀PO₆₉EO₂₀ (P123), sodium dodecylbenzene sulfonate (SDBS), and 1,1,2,2,3,3,4,4,4-nonafluoro-1-butyl sulfonate (NFBS) was chemically used for synthesis under acid condition via sol-gel method then SPP was employed for template removal. The ordered 2D hexagonal arrangement was observed by the evidence of high resolution TEM and the diffraction mode of X-ray. The efficiency of SPP depending on the pH of the discharge solution and discharge time was scientifically demonstrated as a function of BET surface area. In the case of pH dependence, it was achieved that the ability of template removal in acid and base solutions was clearly higher than those of such results in neutral solution. In the term of discharge time, moreover, the percentage of template removal comparing in the result of BET surface area increased as the increase in discharge time.     

Synthesis of silver-integrated silica nanostructures using rice hulls and their electrochemical performance for supercapacitor application

We report the synthesis of silver-integrated silica nanostructures using rice hulls and silver chloride through a facile thermal combustion process. The formation of mesoporous silica nanomatrix embedded with silver nanoparticles (SiO₂:Ag 5 wt% and SiO₂:Ag 10 wt%) was confirmed by XRD, FTIR, EDX, BET, and TEM analysis. Also, the obtained results from the above studies revealed that the concentration of silver ions significantly increases the particle size and number of silver nanoparticles formed in the silica matrix. The electrochemical performance was studied using silver-integrated silica nanostructures as a working electrode in KOH electrolyte. The maximum specific capacitance of SiO₂:Ag 5 wt%- and SiO₂:Ag 10 wt%-coated electrode was found to be 517 and 580 F/g at current density of 1 A/g. It was also found that SiO₂:Ag 10 wt% electrode exhibit an excellent stability with the capacitance retention of 94% than SiO₂:Ag 5 wt% (capacitance retention of 85%) after 1000 cycles at a current density of 1 A/g. These results may be attributed to the inherent characteristic of more silver nanoparticles present in the silica nanomatrix in SiO₂:Ag 10 wt%. The intrinsic characteristic of rice hull-derived silica nanostructures such as high surface area and mesoporous structure along with the advantage of silver nanoparticles (conductivity) can facilitate the Faradic redox processes at electrode surface which are responsible for the supercapacitive behavior of the prepared silver-integrated silica nanostructures.

     

Characterization of silica-coated Ag nanoparticles synthesized using a water-soluble nanoparticle micelle

This article describes the synthesis of silica-coated Ag nanoparticles using a water-soluble nanoparticle micelle under basic conditions. Monodispersed Ag nanoparticles with a mean particle size of 7 nm were synthesized using AgNO₃ in the presence of ascorbic acid as a reducing agent. The Ag nanoparticles were easily re-dispersed into an aqueous solution by surface adsorption of surfactant molecules, indicating formation of water-soluble nanoparticle micelles. Silica-coated Ag nanoparticles ranging in size from 50 to 100 nm were obtained by controlling the surfactant, Ag nanoparticle and tetraethylortho silicate (TEOS) concentrations. Adsorbed surfactant monolayers on Ag nanoparticles were used as a template for the silica shell because of the hydrophobicity of TEOS. In all cases, the size of the resulting particles increased linearly as these concentrations increased. Based on transmission electron microscopy, all the Ag nanoparticles were completely covered with a silica shell. In most samples, however, Ag nanoparticle size increased from 7 to 50 nm due to evaporation of hexane by heating. Although mean particle size of silica-coated Ag nanoparticles was drastically altered, characteristic absorption peaks were observed at approximately 410 nm.     

Preparation and electrochemical characteristics of mesoporous carbon spheres for supercapacitors

Mesoporous carbon spheres serving as electrode materials for supercapacitors were synthesized by a facile polymerization-induced colloid aggregation method using melamines as a carbon precursor and commercial colloidal silica as a silica source for hard template. After the carbonization of as-formed resins-template composites at 1000 °C and the removal of the silica template by hydrofluoric acid, the resulting mesoporous carbon spheres with a diameter size of ∼5 μm, specific surface area (up to 1280 m²/g) and uniform pore size as large as 30 nm could be obtained. Due to the enriched nitrogen content and the large pore size of the mesoporous carbon spheres affecting the surface wettability, resistance, and ion diffusion process in the pores, the mesoporous carbon spheres showed a high specific capacitance of 196 F/g in 5 mol/l H₂SO₄ electrolytes at a discharge current density of 1 A/g.     

Palladium supported on functionalized mesoporous silica as an efficient catalyst for Heck reaction

Pd nanoparticles supported in functionalized mesoporous silica were prepared. Mesoporous silica support was modified with [3-(2-aminoethyl aminopropyl)] trimethoxysilane. Palladium ions were grafted onto the functionalized mesoporous silica and reduced with hydrazine hydrate to obtain the Pd nanoparticles supported on functionalized mesoporous silica. The Pd loading in the nanocomposite of Pd supported on the functionalized mesoporous silica is 4.30 wt%. CO chemisorption analysis on the nanocomposite shows a Pd dispersion as high as 35% and a Pd surface area of 156 m²/g. The surface area, pore size, and pore volume decrease slightly with the incorporation of the Pd nanoparticles into the functionalized mesoporous silica. Pd supported on the functionalized mesoporous silica with controlled molar ratio of amino groups to palladium exhibits an excellent catalytic activity and low Pd leaching for the Heck carbon-carbon coupling reaction. The catalyst can be reused for at least six recycles in air with only a minor loss of activity.     

Synthesis of silica/Au core-shell nanostructures by galvanic replacement of silica/Ag in aqueous and alkaline medium

We present here a facile one-step method for the synthesis of silica/Au core-shell nanostructures by exploiting the potential difference of AuCl₄^? and Ag in aqueous as well as alkaline media. Initially, silica/Ag core-shell nanostructures were synthesised by coating Ag nanoparticles on silica core (size ～150 nm) in a two-step process (seeding and growth) and were characterised for their morphological, structural and optical behaviours. A complete coverage of silica core with Ag nanoparticles was seen from scanning electron microscope and transmission electron microscope images. The presence of resonance peaks in the optical spectrum manifests the nature of the shell (thin shell ～413 and 650 nm, thick shell ～434 nm). Galvanic replacement of silica/Ag core-shell nanostructures in chloroauric acid solution (HAuCl₄) was studied in both the aqueous and alkaline medium, where an aqueous environment results into fast and effective replacement as compared to an alkaline medium, which has been confirmed from optical absorption studies. The optical studies showed that in an alkaline environment, on galvanic replacement of Ag with Au, the individual absorption peak of Ag (～414 nm) and Au (～520 nm) disappeared, whereas new absorption wavelengths in higher region (600–800 nm) of electromagnetic spectrum were observed. A detailed mechanism is proposed for the same to explain this behaviour. A range of novel new plasmonic core-shell nanomaterials can be synthesised as an intermediate of this facile one-step reaction.     

Fabrication of Ag nanoparticles-coated macroporous SiO2 structure by using polystyrene spheres

Ag nanoparticles-coated macroporous SiO₂ structure was fabricated by a novel approach in which at first Ag nanoparticles were coated onto polystyrene (PS) spheres without a surfactant, then these Ag nanoparticles-coated PS beads (Ag/PS) were self-assembled by sedimentation-aggregation with tetraethyl orthosilicate (TEOS), and finally Ag nanoparticles-coated macroporous silica (Ag/SiO₂) was obtained after removal of the PS cores. The heat-treatment temperature and the gelation time were investigated to optimize the microstructural morphology, thermal decomposition of organic materials, matrix wall thickness and densification behavior. The three dimensionally assembled Ag/SiO₂ had 200 nm uniform macropores and a high specific surface area of 142 m² g⁻¹. The XRD, FE-SEM, EDX, BET and optical absorbance analysis indicated that the exactly three-dimensional structure of the template had been imprinted in the final samples and the walls of the macroporous SiO₂ were coated uniformly with Ag nanoparticles.     

Conformal Coating of Co/N‐Doped Carbon Layers into Mesoporous Silica for Highly Efficient Catalytic Dehydrogenation–Hydrogenation Tandem Reactions

To maximize the utilizing efficiency of cobalt (Co) and optimize its catalytic activity and stability, engineering of size and interfacial chemical properties, as well as controllable support are of ultimate importance. Here, the concept of coating uniform thin Co/N‐doped carbon layers into the mesopore surfaces of mesoporous silica is proposed for heterogeneous aqueous catalysis. To approach the target, a one‐step solvent‐free melting‐assisted coating process, i.e., heating a mixture of a cobalt salt, an amino acid (AA), and a mesoporous silica, is developed for the synthesis of mesoporous composites with thin Co/N‐doped carbon layers uniformly coated within mesoporous silica, high surface areas (250–630 m² g⁻¹), ordered mesopores (7.0–8.4 nm), and high water dispersibility. The strong silica/AA adhesive interactions and AA cohesive interactions direct the uniform coating process. The metal/N coordinating, carbon anchoring, and mesopore confining lead to the formation of tiny Co nanoclusters. The carbon intercalation and N coordination optimize the interfacial properties of Co for catalysis. The optimized catalyst exhibits excellent catalytic performance for tandem hydrogenation of nitrobenzene and dehydrogenation of NaBH₄ with well‐matched reaction kinetics, 100% conversion and selectivity, high turnover frequencies, up to ≈6.06 mol_nitrobenzene mol_Co⁻¹ min⁻¹, the highest over transition‐metal catalysts, and excellent stability and magnetic separability.     

The morphology and size of nanostructured Au in Au/SBA-15 affected by preparation conditions

Template-free mesoporous silica SBA-15 was reacted with TPTAC to generate positively charged functional groups PTA⁺ on the pore surface. Through ion exchange, a uniform distribution of anionic metal complexes on the intrachannel surface of host silica was achieved. In this study, ethanol and water were used as solvent for HAuCl₄ precursor solutions impregnated on SBA-15 mesoporous silica. The solvent used can affect the size and location of the resulting nanoparticles. Large Au nanoparticles (15–43 nm) were found on the as-prepared Au/SBA-15 as observed by PXRD, XAS, UV–vis and TEM. This may have originated through Si–OH reduction of chloroaurate complexes generated in the aqueous solution of HAuCl₄, and such particles were not present when ethanolic solution was used. After NaBH₄ and H₂ reduction, the average size of Au nanoparticles, which was incorporated into the channels of SBA-15, was found to be limited to ≤  7 nm.     

Controlled synthesis of semiconductor PbWO4 nanocrystals inside silica SBA-15 materials

A new flexible approach is developed to synthesize PbWO₄ nanoparticles inside the channels of mesoporous silica SBA-15. Mesoporous SBA-15 silica with 7 nm pores was produced by a hydrothermal process and used as a hard template. PbWO₄ nanoparticles were synthesized and incorporated into the mesoporous silicate support in a low-power ultrasonication condition. The as-synthesized samples were characterized by Raman spectroscopy, diffuse reflectance UV–vis spectroscopy (UV–vis), powder X-ray diffraction (XRD), small-angle X-ray diffraction (SAXRD), nitrogen adsorption and transmission electron microscopy (TEM). It was found that PbWO₄ nanoparticles appeared among the channels of SBA-15. Blue shift was observed in UV–vis absorption spectra due to the quantum size effect of PbWO₄ nanoparticles. This preparation method is also capable of synthesis of various semiconductor nanoparticles with controlled size and morphology inside the channels of mesoporous materials.     

Synthesis and characterization of ordered and cubic mesoporous silica crystals under a moderately acidic condition

Ordered and cubic mesoporous silica materials were synthesized by using poly(ethylene oxide-b-propylene oxide-b-ethylene oxide) triblock copolymer as template under a moderately acidic condition of 0.5 mol/l HCl solution. These mesoporous materials were characterized by Fourier transform (FT) IR spectroscopy, thermo-gravimetric analysis (TGA), X-ray diffraction (XRD) pattern, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and nitrogen adsorption–desorption measurements. The three-dimensional cage-like microporosity of the prepared mesoporous silica having ordered hexagonal mesoporous structure was evidenced by the well-defined XRD patterns combined with TEM photographs. SEM observation shows a highly regular cubic crystal structure for the prepared mesoporous silica. The size of these crystallites was maintained within the range between 4 and 6 μm, which is fairly important for the application to the stationary phase for separation. The nitrogen adsorption–desorption analysis reveals that the prepared mesoporous silica possesses a small pore diameter of 3.68 nm, a total surface area of 363.648 m²/g, a total pore volume of 0.379 cm³/g, and a pore-wall thickness of 6.63 nm. These features may lead to higher thermal and hydrothermal stability, excellent microporosity, and good connectivity. The mesoporous silica prepared in this study exhibits potential applications to catalysis, sensoring, and separation.     

Synthesis of oleic acid-stabilized silver nanoparticles and analysis of their antibacterial activity

The development of new and simple green chemical methods for synthesizing colloidal solutions of functional nanoparticles is desirable for environment-friendly applications. In the present work, we report a feasible method for synthesizing colloidal solutions of silver nanoparticles (Ag NPs) based on the modified Tollens technique. The Ag NPs were stabilized by using oleic acid as a surfactant and were produced for the first time by the reduction of silver ammonium complex [Ag(NH₃)₂]⁺_(aq) by glucose with UV irradiation treatment. A stable and nearly monodisperse aqueous Ag NPs solution with average-sized particles (~ 9–10 nm) was obtained. The Ag NPs exhibited high antibacterial activity against both Gram-negative Escherichia Coli (E. coli) and Gram-positive Staphylococcus aureus bacteria. Electron microscopic images and analyses provided further insights into the interaction and bactericidal mechanism of the Ag NPs. The proposed method of synthesis is an effective way to produce highly bactericidal colloidal solutions for medical, microbiological, and industrial applications.     

Preparation and characterisation of silica‐based nanoparticles for cisplatin release on cancer brain cells

In the present work, the preparation, characterisation, and efficiency of two different silica nanostructures as release vehicles of Cisplatin are reported. The 1‐hexadeciltrimethyl‐ammonium bromide templating agent was used to obtain mesoporous silica nanoparticles which were later loaded with Cisplatin. While sol–gel silica was very fast prepared using an excess of acetic acid during the hydrolysis–condensation reactions of tetraethylorthosilicate and at the same time the Cisplatin was added. Several physicochemical techniques including spectroscopies, electronic microscopy, X‐ray diffraction, N₂ adsorption–desorption were used to characterise the silica nanostructures. An in vitro Cisplatin release test was carried out using artificial cerebrospinal fluid. Finally, the toxicity of all silica nanostructures was tested using the C6 cancer cell line. The spectroscopic results showed the suitable stabilisation of Cisplatin into the two different silica nanostructures. A large surface area was obtained for the mesoporous silica nanoparticles, while low areas were obtained in the silica nanoparticles. Cisplatin was released faster from mesoporous silica channels than from inside of aggregates nanoparticles silica. Cisplatin alone, as well as, cisplatin released from both silica nanostructures exerted a toxic effect on cancer cells. In contrast, both silica structures without the drug did not exert any toxic effect.Inspec keywords: cellular biophysics, desorption, adsorption, biomedical materials, sol‐gel processing, silicon compounds, cancer, toxicology, nanofabrication, brain, condensation, mesoporous materials, nanoparticles, X‐ray diffraction, nanomedicine, drugs, aggregates (materials)Other keywords: mesoporous silica channels, silica‐based nanoparticles, cancer brain cells, silica nanostructures, 1‐hexadeciltrimethyl‐ammonium bromide, mesoporous silica nanoparticles, sol‐gel silica, C6 cancer cell line, in vitro cisplatin release test, C6 cancer cell line, acetic acid, hydrolysis‐condensation reactions, tetraethylorthosilicate, physicochemical techniques, electronic microscopy, X‐ray diffraction, N₂ adsorption‐desorption, artificial cerebrospinal fluid, toxicity, toxic effect, N₂ , SiO₂      

Fabrication and textural characterization of nanoporous carbon electrodes embedded with CuO nanoparticles for supercapacitors

Abstract

We introduce a novel strategy of fabricating nanoporous carbons loaded with different amounts of CuO nanoparticles via a hard templating approach, using copper-containing mesoporous silica as the template and sucrose as the carbon source. The nature and dispersion of the CuO nanoparticles on the surface of the nanoporous carbons were investigated by x-ray diffraction (XRD), high-resolution scanning electron microscopy (HRSEM) and high-resolution transmission electron microscopy (HRTEM). XRD results reveal that nanoporous carbons with embedded CuO nanoparticles exhibit a well-ordered mesoporous structure, whereas the nitrogen adsorption measurements indicate the presence of excellent textural characteristics such as high surface area, large pore volume and uniform pore size distribution. The amount of CuO nanoparticles in the nanochannels of the nanoporous carbon could be controlled by simply varying the Si/Cu molar ratio of the mesoporous silica template. Morphological characterization by SEM and TEM reveals that high-quality CuO nanoparticles are distributed homogeneously within the nanoporous carbon framework. The supercapacitance behavior of the CuO-loaded nanoporous carbons was investigated. The material with a small amount of CuO in the mesochannels and high surface area affords a maximum specific capacitance of 300 F g^-1 at a 20 mV s^-1 scan rate in an aqueous electrolyte solution. A supercapacitor containing the CuO-loaded nanoporous carbon is highly stable and exhibits a long cycle life with 91% specific capacitance retained after 1000 cycles.     

The size modulation of hollow mesoporous carbon spheres synthesized by a simplified hard template route

Hollow mesoporous carbon spheres (HMCSs) have been prepared by a simplified replication route from a solid silica core/mesoporous silica shell aluminosilicate (SCMS-Al) template, which was synthesized by directly incorporating aluminum species into the mesoporous framework during template synthesis. The size of HMCSs can be tuned between 80 and 470 nm by simply changing the diameters of SCMS-Al. The HMCSs have uniform mesopores with a narrow pore size distribution (3.4-4.1 nm), and high surface area, (890-1150 m²/g) and total pore volumes (0.75-1.15 cm³/g). The techniques of N₂ sorption isotherms, TEM, EDX and SEM were used to characterize the as-synthesized spheres.     

Surface-enhanced Raman spectroscopy studies of orderly arranged silica nanospheres-synthesis,characterization and dye detection

Silica nanospheres have been explored much for drug delivery, photocatalysis, sensors and energy storage applications. It also acts as a template for Surface-Enhanced Raman Spectroscopy (SERS) substrates. Uniform nanostructures at low cost with high reproducibility are the major challenges in SERS substrate fabrication. In the present work, silica nanospheres were synthesized using stober method and deposited on to glass slides using Vertical deposition techniques. Different size/thickness of Silver (Ag) nanoparticles were deposited onto silica thin films using sputter deposition technique. The monodispersity of silica nanospheres and size of silver nanoparticles (10 nm, 20 nm and 30 nm) were confirmed by FESEM analysis. The structural properties were confirmed through XRD. UV–Vis analysis revealed that the plasmonic properties of Ag@SiO₂ give high surface plasmons for 30 nm thickness of silver. The binding energy of Ag@SiO₂ confirmed through XPS spectrum. The fabricated SERS substrates were used to detect Rhodamine 6G (R6G), Methylene blue (MB), Methylene violet (MV) and Methyl orange dyes as an analyte molecule with a limit of detection at about 10^?11 mol/L. The addition of SiO₂ nanospheres decreases the Ag oxidation rate and increases their stability. The maximum enhancement factor (1.5?×?10⁷) achieved for 30nm thickness of Ag@SiO₂. The results and technique establish the potential applications and reproducible SERS substrate.

     

Synthesis process of gold nanoparticles in solution plasma

We describe the dynamics of the synthesis of gold nanoparticles by a glow discharge in aqueous solutions. A pulsed power supply was used to generate discharges in the aqueous solutions. The initial [AuCl₄]⁻ ion concentration and the voltage applied between the electrodes were varied. The [AuCl₄]⁻ ion was reduced by the H radicals generated in the discharge. The reduction rates were calculated from the changes in the [AuCl₄]⁻ ion concentration during the discharge time. Dendrite-shaped nanoparticles of about 150 nm size were formed in discharge during 1 min. The pH of the solution decreased gradually with the increase of the discharge time. The decrease in pH led to the dissolution of gold nanoparticles. The reduction and the dissolution rates increased proportionately with the applied voltage. The size of the gold nanoparticles decreased at 20 nm after running the discharge during 45 min. Moreover gold nanoparticles with exotic shapes, such as triangle, pentagon, and hexagon were also observed. The particles were confirmed to be as polycrystalline gold nanoparticles by electron diffraction patterns. In summary, when the reduction rate lowered as a result of dissolution, anisotropic nanoparticles were formed and continued to grow in size in the solution.     

Synthesis of 3-dimensional mesoporous silica using a di-block copolymer template

Exploring polymeric surfactants as templates for synthesizing ordered mesoporous silicas has become increasingly important for both academic interests and industrial applications. In this work, we employed C₁₆EO₄₀, a di-block copolymer polyethylene-poly(ethylene oxide), as template in an attempt to synthesize a modified 3-dimensional wormhole mesoporous silicas (WMS-39). In addition, various synthesizing conditions were investigated, including pre-hydrolysis time of TEOS, reaction temperatures and the ratios of TEOS to template. The products were characterized using powder XRD, TEM, ²⁹Si MAS NMR and nitrogen adsorption measurements. The characteristics of as-synthesized mesoporous silica were compared with SBA-15, a highly ordered mesoporous silica, prepared using non-ionic tri-block copolymers of poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) as templates. The WMS-39 materials have a BET surface area of 600–970 m²/g and narrowly distributed pore diameter around 3.9 nm. The morphology of WMS-39 was found to be wormhole framework as indicated in TEM diagrams. Thermal transformation of the as-synthesized mesoporous materials were carefully analyzed with TGA/DTA. Findings obtained from this work enable us to propose a modified assembly mechanism of mesoporous silicas.