Performance Improvement of N-Type $hbox{TiO}_{x}$ Active-Channel TFTs Grown by Low-Temperature Plasma-Enhanced ALD

We report on performance improvement of $n$-type oxide–semiconductor thin-film transistors (TFTs) based on $hbox{TiO}_{x}$ active channels grown at 250 $^{circ}hbox{C}$ by plasma-enhanced atomic layer deposition. TFTs with as-grown $hbox{TiO}_{x}$ films exhibited the saturation mobility $(mu_{rm sat})$ as high as 3.2 $hbox{cm}^{2}/hbox{V}cdothbox{s}$ but suffered from the low on–off ratio $(I_{rm ON}/I_{rm OFF})$ of $hbox{2.0} times hbox{10}^{2}$. $hbox{N}_{2}hbox{O}$ plasma treatment was then attempted to improve $I_{rm ON}/I_{rm OFF}$. Upon treatment, the $hbox{TiO}_{x}$ TFTs exhibited $I_{rm ON}/I_{rm OFF}$ of $hbox{4.7} times hbox{10}^{5}$ and $mu_{rm sat}$ of 1.64 $hbox{cm}^{2}/hbox{V}cdothbox{s}$, showing a much improved performance balance and, thus, demonstrating their potentials for a wide variety of applications such as backplane technology in active-matrix displays and radio-frequency identification tags.      

Linear Systems, Sparse Solutions, and Sudoku

In this paper, we show that Sudoku puzzles can be formulated and solved as a sparse linear system of equations. We begin by showing that the Sudoku ruleset can be expressed as an underdetermined linear system: ${mmb{Ax}}={mmb b}$, where ${mmb A}$ is of size $mtimes n$ and $n>m$. We then prove that the Sudoku solution is the sparsest solution of ${mmb{Ax}}={mmb b}$, which can be obtained by $l_{0}$ norm minimization, i.e. $minlimits_{mmb x}Vert{mmb x}Vert_{0}$ s.t. ${mmb{Ax}}={mmb b}$. Instead of this minimization problem, inspired by the sparse representation literature, we solve the much simpler linear programming problem of minimizing the $l_{1}$ norm of ${mmb x}$, i.e. $minlimits_{mmb x}Vert{mmb x}Vert_{1}$ s.t. ${mmb{Ax}}={mmb b}$, and show numerically that this approach solves representative Sudoku puzzles.      

10-GHz and 20-GHz Channel Spacing High-Resolution AWGs on InP

This letter reports on 10-GHz and 20-GHz channel-spacing arrayed waveguide gratings (AWGs) based on InP technology. The dimensions of the AWGs are 6.8$,times,$8.2 mm$^{2}$ and 5.0$,times,$6.0 mm$^{2}$, respectively, and the devices show crosstalk levels of $-$12 dB for the 10-GHz and $-$17 dB for the 20-GHz AWG without any compensation for the phase errors in the arrayed waveguides. The root-mean-square phase errors for the center arrayed waveguides were characterized by using an optical vector network analyzer, and are 18 $^{circ}$ for the 10-GHz AWG and 28$^{circ}$ for the 10-GHz AWG.      

$hbox{TiN/ZrO}_{2}$/Ti/Al Metal–Insulator–Metal Capacitors With Subnanometer CET Using ALD-Deposited $hbox{ZrO}_{2}$ for DRAM Applications

We provide the first report of the structural and electrical properties of $hbox{TiN/ZrO}_{2}$/Ti/Al metal–insulator–metal capacitor structures, where the $hbox{ZrO}_{2}$ thin film (7–8 nm) is deposited by ALD using the new zirconium precursor ZrD-04, also known as Bis(methylcyclopentadienyl) methoxymethyl. Measured capacitance–voltage ($C$– $V$) and current–voltage ( $I$–$V$) characteristics are reported for premetallization rapid thermal annealing (RTP) in $hbox{N}_{2}$ for 60 s at 400 $^{circ}hbox{C}$, 500 $^{circ}hbox{C}$, or 600 $^{ circ}hbox{C}$. For the RTP at 400 $^{circ}hbox{C}$ , we find very low leakage current densities on the order of nanoamperes per square centimeter at a gate voltage of 1 V and low capacitance equivalent thickness values of $sim$ 0.9 nm at a gate voltage of 0 V. The dielectric constant of $ hbox{ZrO}_{2}$ is 31 $pm$ 2 after RTP treatment at 400 $^{circ}hbox{C}$.      

640 Gbit/s (64-Wavelength $,times,$10 Gbit/s) Data-Rate Wide-Colored NRZ-DPSK Optical Packet Switching and Buffering Demonstration

We demonstrated optical packet switching and buffering operation of a DWDM/NRZ-DPSK optical packet, whose payload-data-rate is 640 Gbit/s (64-wavelength$,times,$10 Gbit/s), for transparent optical packet switch systems for the first time. Error-free (bit-error-rate ${≪}10^{- 9}$) operation including 200-Gchip/s PSK optical label processing was achieved for all 64-wavelength-channel 10 Gbit/s DPSK packet-payloads. In addition, the higher tolerance of DPSK format for packet power fluctuation compared with OOK one was verified in an optical packet switch system.      

High-Density and Low-Leakage-Current MIM Capacitor Using Stacked $hbox{TiO}_{2}/hbox{ZrO}_{2}$ Insulators

We have fabricated high-$kappa hbox{Ni}/hbox{TiO}_{2}/hbox{ZrO}_{2}/ hbox{TiN}$ metal–insulator–metal (MIM) capacitors. A low leakage current of $hbox{8} times hbox{10}^{-8} hbox{A/cm}^{2}$ at 125 $^{circ}hbox{C}$ was obtained with a high 38- $hbox{fF}/muhbox{m}^{2}$ capacitance density and better than the $hbox{ZrO}_{2}$ MIM capacitors. The excellent device performance is due to the lower electric field in 9.5-nm-thick $hbox{TiO}_{2}/ hbox{ZrO}_{2}$ devices to decrease the leakage current and to a higher $kappa$ value of 58 for $ hbox{TiO}_{2}$ as compared with that of $hbox{ZrO}_{2}$ to preserve the high capacitance density.      

Schottky Barrier Height Modulation of Nickel–Dysprosium-Alloy Germanosilicide Contacts for Strained P-FinFETs

This letter reports on the fabrication and hole Schottky barrier $(Phi_{ rm B}^{rm p})$ modulation of a novel nickel (Ni)–dysprosium (Dy)-alloy germanosilicide (NiDySiGe) on silicon–germanium (SiGe). Aluminum (Al) implant is utilized to lower the $Phi_{rm B}^{rm p}$ of NiDySiGe from $sim$0.5 to $sim$ 0.12 eV, with a correspondingly increasing Al dose in the range of $ hbox{0}$–$hbox{2}timeshbox{10}^{15} hbox{atoms}/ hbox{cm}^{2}$. When integrated as the contact silicide in p-FinFETs (with SiGe source/drain), NiDySiGe with an Al implant dose of $hbox{2}timeshbox{10}^{14} hbox{atoms}/ hbox{cm}^{2}$ leads to 32% enhancement in $I_{rm DSAT}$ over p-FinFETs with conventional NiSiGe contacts. Ni–Dy-alloy silicide is a promising single silicide solution for series-resistance reduction in CMOS FinFETs.      

Improved Stress Reliability of Analog Metal–Insulator–Metal Capacitors Using $hbox{TiO}_{2}/hbox{ZrO}_{2}$ Dielectrics

We have studied the stress reliability of high-$kappa$ $hbox{Ni/TiO}_{2}/hbox{ZrO}_{2}/hbox{TiN}$ metal–insulator–metal capacitors under constant-voltage stress. The increasing $hbox{TiO}_{2}$ thickness on $hbox{ZrO}_{2}$ improves the 125-$^{circ}hbox{C}$ leakage current, capacitance variation $(Delta C/C)$, and long-term reliability. For a high density of 26 $hbox{fF}/mu hbox{m}^{2}$ , good extrapolated ten-year reliability of small $Delta C/ break C sim hbox{0.71}%$ is obtained for the $ hbox{Ni/10-nm-}hbox{TiO}_{2}/hbox{6.5-nm-} hbox{ZrO}_{2}/break hbox{TiN}$ device at 2.5-V operation.      

1580-V–40-$hbox{m}Omegacdot hbox{cm}^{2}$ Double-RESURF MOSFETs on 4H-SiC $(hbox{000}bar{hbox{1}})$

Double-reduced-surface-field (RESURF) MOSFETs with $hbox{N}_{2}hbox{O}$ -grown oxides have been fabricated on the 4H-SiC $(hbox{000} bar{hbox{1}})$ face. The double-RESURF structure is effective in reducing the drift resistance, as well as in increasing the breakdown voltage. In addition, by utilizing the 4H-SiC $(hbox{000}bar{hbox{1}})$ face, the channel mobility can be increased to over 30 $hbox{cm}^{2}/hbox{V}cdothbox{s}$, and hence, the channel resistance is decreased. As a result, the fabricated MOSFETs on 4H-SiC $( hbox{000}bar{hbox{1}})$ have demonstrated a high breakdown voltage $(V_{B})$ of 1580 V and a low on-resistance $(R_{rm ON})$ of 40 $hbox{m}Omega cdothbox{cm}^{2}$. The figure-of-merit $(V_{B}^{2}/R_{rm ON})$ of the fabricated device has reached 62 $hbox{MW/cm}^{2}$, which is the highest value among any lateral MOSFETs and is more than ten times higher than the “Si limit.”      

Zn$_{1 - x}$Mg$_{x}$ O Homojunction-Based Ultraviolet Photodetector

Zn$_{1 - {x}}$ Mg$_{x}$ O p-n photodiodes were fabricated on (0001) sapphire substrates using a pulsed laser deposition technique with different Mg contents. Ti–Au and Ni–Au metals deposited using vacuum evaporation were used as n-type and p-type contacts, respectively. The X-ray diffraction analysis showed the Zn$_{1 - {x}}$Mg$_{x}$O double layers have a single phase hexagonal wurtzite structure. The optical bandgap of Zn$_{1 - {x}}$Mg$_{x}$O films has been tuned from 3.27 to 4.26 eV by increasing the Mg content ${x} =0.0$ to ${x}=0.34$. Correspondingly, the cutoff wavelength of the resultant detectors varies from 380 to 284 nm. Zn$_{1 - {x}}$Mg$_{x}$O p-n photodiodes with different Mg contents exhibit very good performance, with a very low dark current (${≪}$ 20 pA) at the bias voltage of 10 V. The ultraviolet to visible rejection ratio is more than three orders of magnitude.      

Q-Band pHEMT and mHEMT Subharmonic Gilbert Upconversion Mixers

This letter makes a comparison between Q-band 0.15 $mu{rm m}$ pseudomorphic high electron mobility transistor (pHEMT) and metamorphic high electron mobility transistor (mHEMT) stacked-LO subharmonic upconversion mixers in terms of gain, isolation and linearity. In general, a 0.15 $mu{rm m}$ mHEMT device has a higher transconductance and cutoff frequency than a 0.15 $mu{rm m}$ pHEMT does. Thus, the conversion gain of the mHEMT is higher than that of the pHEMT in the active Gilbert mixer design. The Q-band stacked-LO subharmonic upconversion mixers using the pHEMT and mHEMT technologies have conversion gain of $-$7.1 dB and $-$0.2 dB, respectively. The pHEMT upconversion mixer has an ${rm OIP}_{3}$ of $-$12 dBm and an ${rm OP}_{1 {rm dB}}$ of $-$24 dBm, while the mHEMT one shows a 4 dB improvement on linearity for the difference between the ${rm OIP}_{3}$ and ${rm OP}_{1 {rm dB}}$. Both the chip sizes are the same at 1.3 mm $times$ 0.9 mm.      

Low-Threshold Strained Quantum-Well GaSb-Based Lasers Emitting in the 2.5- to 2.7-$mu$ m Wavelength Range

GaInAsSb–GaSb strained quantum-well (QW) ridge waveguide diode lasers emitting in the wavelength range from 2.51 to 2.72 $ mu{hbox {m}}$ have been grown by molecular beam epitaxy. The devices show ultralow threshold current densities of 44 $hbox{A}/{hbox {cm}}^{2}$ (${L}rightarrow infty $) for a single QW device at 2.51 $ mu{hbox {m}}$, which is the lowest reported value in continuous-wave operation near room temperature (15 $^{circ}hbox{C}$) at this wavelength. The devices have an internal loss of 3 ${hbox {cm}}^{-1}$ and a characteristic temperature of 42 K. By using broader QWs, wavelengths up to 2.72 $mu{hbox {m}}$ could be achieved.      

Positive Bias Temperature Instability (PBTI) Characteristics of Contact-Etch-Stop-Layer-Induced Local-Tensile-Strained $hbox{HfO}_{2}$ nMOSFET

The positive bias temperature instability (PBTI) characteristics of contact-etch-stop-layer (CESL)-strained $hbox{HfO}_{2}$ nMOSFET are thoroughly investigated. For the first time, the effects of CESL on an $hbox{HfO}_{2}$ dielectric are investigated for PBTI characteristics. A roughly 50% reduction of $V_{rm TH}$ shift can be achieved for the 300-nm CESL $hbox{HfO}_{2}$ nMOSFET after 1000-s PBTI stressing without obvious $ hbox{HfO}_{2}/hbox{Si}$ interface degradation, as demonstrated by the negligible charge pumping current increase ($≪$ 4%). In addition, the $hbox{HfO}_{2}$ film of CESL devices has a deeper trapping level (0.83 eV), indicating that most of the shallow traps (0.75 eV) in as-deposited $ hbox{HfO}_{2}$ film can be eliminated for CESL devices.      

2 MHz AO $Q$ -switched ${rm TEM}_{00}$ Grazing Incidence Laser With 3 at.% Neodymium Doped Nd:YVO$_{4}$

We present a detailed experimental and theoretical study of the ultrahigh repetition rate AO $Q$ -switched ${rm TEM}_{00}$ grazing incidence laser. Up to 2.1 MHz $Q$-switching with ${rm TEM}_{00}$ output of 8.6 W and 2.2 MHz $Q$ -switching with multimode output of 10 W were achieved by using an acousto-optics $Q$ -switched grazing-incidence laser with optimum grazing-incidence angle and cavity configuration. The crystal was 3 at.% neodymium doped Nd:YVO$_{4}$ slab. The pulse duration at 2 MHz repetition rate was about 31 ns. The instabilities of pulse energy at 2 MHz repetition rate were less than ${pm}6.7hbox{%}$ with ${rm TEM}_{00}$ operation and ${pm}3.3hbox{%}$ with multimode operation respectively. The modeling of high repetition rate $Q$-switched operation is presented based on the rate equation, and with the solution of the modeling, higher pump power, smaller section area of laser mode, and larger stimulated emission cross section of the gain medium are beneficial to the $Q$-switched operation with ultrahigh repetition rate, which is in consistent with the experimental results.      

$N times N$ Cyclic-Frequency Router With Improved Performance Based on Arrayed-Waveguide Grating

We have developed an $N times N$ cyclic-frequency router with improved performance by employing two types of modified configuration; a uniform-loss and cyclic-frequency (ULCF) arrayed-waveguide grating (AWG) and an interconnected multiple AWG. We have demonstrated a compact 50-GHz-spacing 64 $,times,$64 ULCF-AWG router with low and uniform insertion losses of 5.4–6.8 dB and frequency deviations from the grid of less than $pm {8}~{rm GHz}$. We have also demonstrated a 100-GHz-spacing 8$,times,$8 interconnected multiple-AWG router with a practical configuration, very low and uniform insertion losses of 2.3–3.4 dB, and frequency deviations from the grid of less than $pm {6}~{rm GHz}$. We discuss the suitable or realizable scale $N$ of the two types of routers by comparison with a conventional AWG router in terms of optical and dimensional performance and productivity.      

Breakdown Enhancement of AlGaN/GaN HEMTs on 4-in Silicon by Improving the GaN Quality on Thick Buffer Layers

We have achieved a 9- $muhbox{m}$-thick AlGaN/GaN high-electron mobility transistor (HEMT) epilayer on silicon using thick buffer layers with reduced dislocation density $(D_{D})$. The crack-free 9- $muhbox{m}$-thick epilayer included 2- $muhbox{m}$ i-GaN and 7- $ muhbox{m}$ buffer. The HEMTs fabricated on these devices showed a maximum drain–current density of 625 mA/mm, transconductance of 190 mS/mm, and a high three-terminal OFF breakdown of 403 V for device dimensions of $L_{g}/W_{g}/L_{rm gd} = hbox{1.5/15/3} muhbox{m}$ . Without using a gate field plate, this is the highest $BV$ reported on an AlGaN/GaN HEMT on silicon for a short $L_{rm gd}$ of 3 $muhbox{m}$. A very high $BV$ of 1813 V across 10- $mu hbox{m}$ ohmic gap was achieved for i-GaN grown on thick buffers. As the thickness of buffer layers increased, the decreased $D_{D}$ of GaN and increased resistance between surface electrode and substrate yielded a high breakdown.      

Surface Deposition of Ionic Contaminants on Silicon Wafers in a Cleanroom Environment

The adsorption and desorption behaviors of ionic micro-contaminants on the silicon wafers in a cleanroom environment were investigated in this study. The experimental measurements showed that the surface density of ionic contaminants was significantly affected by both the exposure time and the properties of contaminants. The rate parameters of a kinetic model for surface deposition were determined by numerical optimization of fitting the experimental data on surface and ambient concentrations of airborne molecular contaminants (AMCs). Subsequently, the time-dependent deposition velocity and sticking coefficient of ionic species were obtained. The results showed that ${rm F}^{-}$, ${rm Cl}^{-}$, ${rm NO}_{3}^{-}$, ${rm SO}_{4}^{2-}$, ${rm Na}^{+}$, ${rm NH}_{4}^{+}$, ${rm K}^{+}$, and ${rm Mg}^{2+}$ were the major ionic microcontamination species on the wafer surfaces, with the adsorption rate constant and the sticking coefficient of ${rm K}^{+}$ ion being larger than those of other ionic contaminants. After the determination of sticking coefficients, the allowable wafer exposure durations and the maximum ambient concentrations of ionic species were exemplified based on the guideline recommended by the International Technology Roadmap for Semiconductors (ITRS).      

A Comparative NBTI Study of $hbox{HfO}_{2}$, $hbox{HfSiO}_{x}$, and SiON p-MOSFETs Using UF-OTF $I_{rm DLIN}$ Technique

The time, temperature, and oxide-field dependence of negative-bias temperature instability is studied in $hbox{HfO}_{2}/hbox{TiN}$, $ hbox{HfSiO}_{x}/hbox{TiN}$, and SiON/poly-Si p-MOSFETs using ultrafast on-the-fly $I_{rm DLIN}$ technique capable of providing measured degradation from very short (approximately microseconds) to long stress time. Similar to rapid thermal nitrided oxide (RTNO) SiON, $hbox{HfO}_{2}$ devices show very high temperature-independent degradation at short (submilliseconds) stress time, not observed for plasma nitrided oxide (PNO) SiON and $hbox{HfSiO}_{x}$ devices. $hbox{HfSiO}_{x}$ shows lower overall degradation, higher long-time power-law exponent, field acceleration, and temperature activation as compared to $hbox{HfO}_{2}$, which are similar to the differences between PNO and RTNO SiON devices, respectively. The difference between $ hbox{HfSiO}_{x}$ and $hbox{HfO}_{2}$ can be attributed to differences in N density in the $hbox{SiO}_{2}$ IL of these devices.      

AlN/GaN Insulated-Gate HEMTs With 2.3 A/mm Output Current and 480 mS/mm Transconductance

High-electron mobility transistors (HEMTs) based on ultrathin AlN/GaN heterostructures with a 3.5-nm AlN barrier and a 3-nm $hbox{Al}_{2}hbox{O}_{3}$ gate dielectric have been investigated. Owing to the optimized AlN/GaN interface, very high carrier mobility $(sim!!hbox{1400} hbox{cm}^{2}/hbox{V}cdothbox{s})$ and high 2-D electron-gas density $(sim!!kern1pthbox{2.7} times hbox{10}^{13} /hbox{cm}^{2})$ resulted in a record low sheet resistance $(sim !!hbox{165} Omega/hbox{sq})$. The resultant HEMTs showed a maximum dc output current density of $simkern1pt$2.3 A/mm and a peak extrinsic transconductance $g_{m,{rm ext}} sim hbox{480} hbox{mS/mm}$ (corresponding to $g_{m,{rm int}} sim hbox{1} hbox{S/mm}$). An $f_{T}/f_{max}$ of 52/60 GHz was measured on $hbox{0.25} times hbox{60} muhbox{m}^{2}$ gate HEMTs. With further improvements of the ohmic contacts, the gate dielectric, and the lowering of the buffer leakage, the presented results suggest that, by using AlN/GaN heterojunctions, it may be possible to push the performance of nitride HEMTs to current, power, and speed levels that are currently unachievable in AlGaN/GaN technology.      

$S$ - and $C$ -Band Ultra-Compact Phase Shifters Based on All-Pass Networks

Ultra-compact phase shifters are presented. The proposed phase-shifting circuits utilize the lumped element all-pass networks. The transition frequency of the all-pass network, which determines the size of the circuit, is set to be much higher than the operating frequency. This results in a significantly small chip size of the phase shifter. To verify this methodology, 5-bit phase shifters have been fabricated in the $S$ - and $C$ -band. The $S$ -band phase shifter, with a chip size of 1.87 mm $,times,$0.87 mm (1.63 mm $^{2}$), has achieved an insertion loss of ${hbox{6.1 dB}} pm {hbox{0.6 dB}}$ and rms phase-shift error of less than 2.8$^{circ}$ in 10% bandwidth. The $C$ -band phase shifter, with a chip size of 1.72 mm $,times,$0.81 mm (1.37 mm $^{2}$), has demonstrated an insertion loss of 5.7 dB $pm$ 0.8 dB and rms phase-shift error of less than 2.3 $^{circ}$ in 10% bandwidth.