Influence of Emulsification Technique and Wall Composition on Physicochemical Properties and Oxidative Stability of Fish Oil Microcapsules Produced by Spray Drying

Encapsulation of fish oil is an effective way to protect it against oxidation and masking its fishy odor. One of the possible ways to produce fish oil microcapsules is to produce an oil-in-water (O/W) emulsion followed by spray drying. This study compares the production of the O/W emulsion by mechanical homogenization (rotor–stator) with membrane emulsification and examines the effect of the type and amount of wall material added before drying. The membrane emulsification process selected for the emulsion production is premix membrane emulsification (ME), which consists of the production of a coarse emulsion by mechanical means followed by droplet breakup when the coarse emulsion is forced through a membrane. The emulsions produced had an oil load of 10 and 20 % and were stabilized using whey protein (isolate and hydrolyzate at 1 or 10 %) and sodium caseinate with concentrations of 2 and 10 %. Regarding the material used to build the microcapsule wall, whey protein, maltodextrin, or combinations of them were used at three different oil/wall ratios (1:1, 1:2, 1:3). The results clearly show that premix ME is a suitable technology for producing O/W emulsions stabilized with proteins, which have a smaller droplet size and are more monodisperse than those produced by rotor–stator emulsification. However, protein concentrations of 10 % are required to reduce the droplet size down to 2–3 μm. Small and monodisperse emulsions have been found to produce microcapsules with lower surface oil content, which increases oil encapsulation efficiency and presents lower levels of oxidation during storage at 30 °C. Of all the possible combinations studied, the one with the highest oil encapsulation efficiency is the production of a 20 % O/W emulsion stabilized with 10 % sodium caseinate followed by the addition of 50 % maltodextrin and drying.     

Interfacial characteristics and microchannel emulsification of oleuropein-containing triglyceride oil–water systems

This study investigated the adsorption characteristics of olive leaf water extract and its major phenolic compound, oleuropein, at the triglyceride oil–water interface. We also investigated the preparation characteristics of food-grade triglyceride oil-in-water (O/W) emulsions stabilized by oleuropein using microchannel (MC) emulsification. Refined soybean oil, extra virgin olive oil, refined olive oil, and medium-chain triacylglyceride (MCT) oil were used as triglyceride oils. Both olive leaf extract (OLE) and highly purified oleuropein had a pronounced ability to decrease the interfacial tension at the refined soybean oil–water interface. The packing of oleuropein molecules at the triglyceride oil–water interface was estimated on the basis of their surface excess concentration and area occupied per molecule, determined from the Gibbs adsorption equation. MC emulsification was performed using a silicon grooved MC array plate (model CMS6-2). The continuous aqueous phase contained 0.6 wt.% of oleuropein. Monodisperse, oleuropein-stabilized O/W emulsions with an average droplet diameter of 25 μm and coefficient of variation (CV) of < 5% were produced in all systems, except the MCT oil-containing system, even in the absence of a cross-flowing continuous phase. This successful MC emulsification was observed without droplet coalescence for 15 h of continuous operation. Our findings demonstrate that the use of oleuropein, which has an interfacial activity, is capable of producing monodisperse O/W emulsions using MC emulsification and stabilizing the generated oil droplets when appropriate types of triglyceride oils are used.     

Preparation and Characterization of Water/Oil/Water Emulsions Stabilized by Polyglycerol Polyricinoleate and Whey Protein Isolate

ABSTRACT: In this study we tried to prepare stable water-in-oil-in-water (W/O/W) emulsions using polyglycerol polyricinoleate (PGPR) as a hydrophobic emulsifier and whey protein isolate (WPI) as a hydrophilic emulsifier. At first, water-in-oil (W/O) emulsions was prepared, and then 40 wt% of this W/O emulsion was homogenized with 60 wt% aqueous solution of different WPI contents (2, 4, and 6 wt% WPI) using a high-pressure homogenizer (14 and 22 MPa) to produce W/O/W emulsions. The mean size of final W/O/W droplets ranged from 3.3 to 9.9 μm in diameter depending on the concentrations of PGPR and WPI. It was shown that most of the W/O/W droplets were small (<5 μm) in size but a small population of large oil droplets (d > 20 μm) was also occasionally observed. W/O/W emulsions prepared at the homogenization pressure of 22 MPa had a larger mean droplet size than that prepared at 14 MPa, and showed a microstructure consisting of mainly approximately 6 to 7-μm droplets. When a water-soluble dye PTSA as a model ingredient was loaded in the inner water phase, all W/O/W emulsions showed a high encapsulation efficiency of the dye (>90%) in the inner water phase. Even after 2 wk of storage, >90% of the encapsulated dye still remained in the inner water phase; however, severe droplet aggregation was observed at relatively high PGPR and WPI concentrations.     

Formulation and Stability Characterization of Rutin-Loaded Oil-in-Water Emulsions

In this work, formulation and characterization of oil-in-water (O/W) emulsions loaded with rutin were successfully overhead. We investigated the effect of homogenization pressure on the mean droplet size, droplet size distribution, physical stability, and rutin retention of these emulsions. O/W emulsions with a mean droplet size (d _3,2) of about 150 nm and a span of nearly the unit were formulated by microfluidization at the homogenization pressure 20–150 MPa. The O/W emulsion droplets loaded with rutin were physically stable in terms of variations of d _3,2 and span during 30 days of storage in the dark condition at 4 and 25 °C. The creaming velocity was characterized using centrifugal method showing a relative good shelf life. HPLC analysis demonstrated that 71–85% of initial rutin was retained in the fresh O/W emulsions and declined to 22–35% (w/w) for 30-day storage at 25 °C. Antioxidant activity assays confirmed that rutin-loaded emulsion participated in the antioxidant activity after encapsulation similarly to pure rutin. These results indicate that O/W emulsion systems can function as potential delivery systems to enhance bioavailability to encapsulate liposoluble antioxidant rutin for potential applications in the food industry.     

A Novel Approach to Improving the Quality of Bittern-Solidified Tofu by W/O Controlled-Release Coagulant. 2: Using the Improved Coagulant in Tofu Processing and Product Evaluation

To improve the quality and yield of traditional firm tofu prepared with bittern as coagulant, water-in-oil (W/O) emulsions with bittern solution as the aqueous phase, where the ratio of the bittern solution to the oil phase was 1:1.5 or 1:1 (w/w), and an emulsifier at a concentration of 0.8 or 1.0 wt.% were prepared. The parameters water content, water-holding capacity, yield, texture, and microstructure of the tofu were tested. The results indicated that the bittern W/O emulsions provided satisfactory controlled-release application potential. The use of the W/O emulsions significantly improved tofu’s water content, and the product remained moist for at least 24 h. Moreover, emulsified bittern increased the yield and made the gel network more homogenous and compact compared with the control. As expected, emulsions with an emulsifier concentration of 1.0 wt.% showed slightly better controlled-release capacity than those with 0.8 wt.%.     

A Novel Approach to Improving the Quality of Bittern-Solidified Tofu by W/O Controlled-Release Coagulant. 1: Preparation of W/O Bittern Coagulant and Its Controlled-Release Property

To explore the controlled-release capacity and potential application of water in oil (W/O) emulsions, W/O emulsions with bittern solution as the aqueous phase were prepared with polyglycerol polyricinoleate (PGPR) as the emulsifier. Several factors that influenced the preparation of W/O bittern coagulants were investigated. Optimized conditions were applied as follows: bittern solution/oil phase at 4:6 or 5:5 (w/w), processing temperature at 65 °C, emulsifier concentration higher than 0.6 wt% and high-pressure homogenization at 60 MPa; W/O emulsions that had a good particle size distribution, good rheological properties, good embedding ratio and high stability were prepared. The optimized W/O emulsions also exhibited the expected controlled-release ability, affected by the bath temperature, shear speed and emulsion characteristics. The preliminary results also showed that the application of W/O emulsions has the potential to improve tofu quality by delaying the solidification of soybean protein and creating a much smoother and finer gel structure.     

The characterization of the semi-solid W/O/W emulsions with low concentrations of the primary polymeric emulsifier

Semi-solid multiple W/O/W emulsions with low concentrations (0.8, 1.6 and 2.4% w/w) of lipophilic polymeric primary emulsifier PEG-30-dipolyhydroxystearate (PDHS) have been formulated. Both emulsions, primary and multiple, were prepared with high content of inner phase (Phi1 = Phi2 = 0.8). All the formulations differ only in the lipophilic emulsifier concentration. Evaluating several parameters such as macroscopic and microscopic aspect, droplet size, accelerated stability under centrifugation and flow and oscillatory rheological behaviour, assessed the multiple systems. It is possible to formulate the semi-solid W/O/W multiple emulsions with low concentrations of PDHS as the primary emulsifier. It appeared that the highest long-term stable multiple emulsion with the lowest droplet size, the highest apparent viscosity and highest elastic characteristic, was the sample with the highest concentration (2.4% w/w) of the primary emulsifier.     

Fish Oil Microcapsules from O/W Emulsions Produced by Premix Membrane Emulsification

Fish oil microcapsules were prepared by combining a low-energy emulsification method (premix membrane emulsification) with spray drying. Oil-in-water (O/W) emulsions were prepared using a two-step emulsification method that used a rotor–stator homogenizer followed by membrane emulsification. The influence of the emulsification method (mechanical stirring or membrane emulsification), the emulsification conditions (membrane and emulsifier type), and the amount of wall material on the physicochemical characteristics of the microcapsules was studied. The results show that the emulsification method and the type and amount of emulsifier and wall material affect the final amount of encapsulated oil. Microcapsules produced by membrane emulsification and stabilized with 2 % Tween-20 or 10 % whey protein presented the highest values (higher than 50 %) of oil encapsulation efficiency (OEE). It has been found that the OEE increases when decreasing the droplet size of the emulsions as well as with the increase of the amount of wall material employed during drying. Morphology analysis showed that the microcapsules obtained from O/W emulsions produced by premix membrane emulsification were rounder in shape, without visible cracks on the surface and no vacuoles on the inside. Oxidation stability tests performed on some selected samples indicate that the microcapsules with higher stability are the ones produced with a higher amount of wall material and have less surface oil.     

负载葡萄皮粉花色苷提取物的W/O/W型复乳制备及其体外消化评价

以葡萄皮花色苷(ACNs)提取物为内水相(W1),玉米油为油相,乳清蛋白(WPI)溶液为外水相(W2)制备水包油包水(W/O/W)型复乳。复乳的包埋率高达(93.19±2.78)%,平均粒径为(287.90±3.12)nm。经口腔消化后,乳液未发现有明显变化;模拟胃部消化后,乳液液滴相互融合形成具有双层结构的较大微粒,其平均粒径(d>600 nm)显著增加(P<0.05)。经模拟肠道消化后,微粒成为空油滴,其平均粒径为(387.53±15.96)nm,此时抗氧化活性最高。研究结果表明,W/O/W型复乳在口腔和胃部能有效保护ACNs,实现靶向性肠道输送。负载ACNs的复乳系统在食品工业中有很大的应用潜力。     

Red ginseng extract capsule fabricated using W/O/W emulsion techniques

The objective of the present study was to investigate the physicochemical characteristics and storage stability of water-in-oil-in-water (W/O/W) emulsions and spray-dried red ginseng extract capsules (RGEC) prepared using different secondary coating materials such as maltodextrin (MD), whey protein concentrate (WPC), or arabic gum (AG). The particle sizes of W/O/W emulsions and spray-dried RGEC coated with MD were considerably lower than those of W/O/W emulsions and spray-dried RGEC coated with WPC or AG. The zeta-potential value (?36 mV) of spray-dried RGEC coated with MD was significantly higher than that of spray-dried RGEC coated with WPC or AG (p < 0.05), indicating that spray-dried RGEC coated with MD were much more stable than spray-dried RGEC coated with WPC and AG. In the storage stability study, it was found that the refrigerator temperature (4°C) was preferred for storing spray-dried samples for a long time. Based on these results, it was confirmed that MD could be the most efficient coating material for W/O/W emulsions and nano-sized spray-dried RGEC.     

Release rate profiles of magnesium from multiple W/O/W emulsions

Water-in-oil-in-water (W/O/W) emulsions were formulated based on rapeseed oil, olive oil, olein and miglyol. Polyglycerol polyricinoleate and sodium caseinate were used as lipophilic and hydrophilic emulsifiers, respectively. Magnesium was encapsulated in the inner aqueous droplets. Emulsion stability was assayed through particle sizing and magnesium release at two storage temperatures (4 and 25 °C) over 1 month. Irrespective of the oil nature, both the primary W/O and W/O/W emulsions were quite stable regarding the size parameters, with 10-μm fat globules and 1-μm internal water droplets. Magnesium leakage from W/O/W emulsions was influenced by the oil type used in the formulation: the higher leakage values were obtained for the oils characterized by the lower viscosity and the higher proportion of saturated fatty acids. Magnesium release was not due to droplet–globule coalescence but rather to diffusion and/or permeation mechanisms with a characteristic rate that varied over time. In addition, W/O/W emulsions were resistant to various thermal treatments that mimicked that used in pasteurization processes. Finally, when W/O/W emulsions were placed in the presence of pancreatic lipase, the emulsion triglycerides were hydrolysed by the enzyme. These results indicated a possible use of W/O/W emulsions loaded with magnesium ions in food applications.     

W/O/W emulsions with high internal droplet volume fraction

We prepared water-in-oil-in-water (W/O/W) double emulsions with high internal aqueous droplet fraction using food-based ingredients. These compartmentalised materials were comprised of oil globules dispersed in an external aqueous phase, with the globules themselves containing densely packed inner aqueous droplets. We were able to obtain double emulsions with large globule fractions (up to 45 vol.%) using only 5 vol.% oil (relative to the overall composition). In the final state, the inner droplet fraction within the globules could exceed 90 vol.%. The method was based on two successive emulsification steps, followed by osmotic swelling (transport of water from the external phase to the inner droplets through the oil phase). During the final step, the swelling was controlled by the osmotic pressure mismatch between the external and internal aqueous phases using solutes dissolved at different concentrations. The osmotic swelling model of Mezzenga et al. (Langmuir, 2004, 20, 3574-3582) was re-adapted in the limit of small Laplace pressures to predict the final composition resulting from osmotic equilibration. The internal droplet fraction was lower than that predicted by the model as a consequence of coalescence phenomena occurring during the swelling process. The proposed approach constitutes a valuable guide within the prospect of formulating emulsions with enhanced encapsulation capacity and reduced fat content.     

Protection of Lactobacillus acidophilus from the low pH of a model gastric juice by incorporation in a W/O/W emulsion

The protective effect of a W/O/W emulsion for Lactobacillus acidophilus from a model gastric juice was investigated in order to develop a method for utilizing the advantages of the probiotics. The bacteria were included in the inner-phase solution of the W/O/W emulsion, and a method for counting the viable-bacteria included in the W/O/W emulsion was developed. The relative viability of the bacteria included in the W/O/W emulsion was 49% at 2 h in the model gastric juice, whereas the viability of the bacteria directly dispersed in the juice declined to 1.3% even at 0.67 h. The relative viabilities of the encapsulated bacteria in the model gastric juice at 2 h were 0.12 and 1.10 for the emulsions having the median diameters of 11.9 and 25.4 μm, prepared with inner-phase volume ratios at 0.03 and 0.45, respectively. The relative viabilities of the bacteria in the W/O/W emulsions with the median diameters of 11 and 27 μm, prepared at the homogenization speed of 2.2×10⁴ and 9.8×10³ rpm, were 0.4 and 0.8, respectively. These results suggested that both the inner-phase volume ratio and the median diameter of oil droplet affected the relative viability of the included bacteria.     

Physical and Oxidative Stabilities of O/W Emulsions Formed with Rice Dreg Protein Hydrolysate: Effect of Xanthan Gum Rheology

The shortening of shelf-life of food emulsions is frequently due to poor creaming and lipid oxidation stability. The lipid oxidation of O/W emulsions can be inhibited by rice dreg protein hydrolysate (RDPH); however, emulsions were stabilized by Tween-20. Polysaccharides can control the rheology and network structure of the aqueous continuous phase by increasing viscosity and yield stress, hence retarding phase separation and gravity-induced creaming, especially for xanthan gum. The objective of this research was to evaluate whether emulsions formed with 2 wt% RDPH and stabilized by xanthan gum (0–0.5 wt%) could produce 20 % (v/v) soybean oil-in-water emulsions that had good physical and oxidative stability. The degree of flocculation of droplets as a function of xanthan gum concentration was assessed by the microstructure, rheology, and the creaming index of emulsions. Addition of xanthan gum prior to homogenization had no significant effect on the mean droplet diameter in all emulsions studied. Increase in xanthan gum concentration led to the increase in creaming stability of emulsions, due to an increase in viscosity of the continuous phase and/or the formation of a droplet network with a yield stress, as well as the enhanced steric and electrostatic repulsion between the droplets. Lipid oxidation of the emulsions was significantly inhibited at xanthan gum concentrations of 0.12 wt% or above with RDPH, which could due to the fact that xanthan gum increases the viscosity of the aqueous phase and hindered the diffusion of oxidants to the oil droplet surface area, synergistic effect between RDPH and xanthan gum to suppress oil peroxidation, and metal ion chelation capability of xanthan gum. Thus, stable protein hydrolyzates-type emulsions could be obtained with increasing concentration of xanthan gum.     

Enhancing anti-inflammation activity of curcumin through O/W nanoemulsions

High-speed and high-pressure homogenized O/W emulsions using medium chain triacylglycerols (MCT) as oil and Tween 20 as emulsifier, with mean droplet sizes ranging from 618.6 nm to 79.5 nm, have been successfully prepared. The enhanced anti-inflammation activity of curcumin encapsulated in O/W emulsions is evidenced by the mouse ear inflammation model. There is a 43% or 85% inhibition effect of 12-O-tetradecanoylphorbol-13-acetate (TPA)-induced edema of mouse ear for 618.6 nm and 79.5 nm 1% curcumin O/W emulsions, respectively, but a negligible effect is found for 1% curcumin in 10% Tween 20 water solution.     

Effect of chitosan on the stability and properties of modified lecithin stabilized oil-in-water monodisperse emulsion prepared by microchannel emulsification

The effect of chitosan (CHI) on the stability of monodisperse modified lecithin (ML) stabilized soybean oil-in-water (O/W) emulsion was investigated. Monodisperse emulsion droplets with particle size of 24.4 ± 0.7 μm and coefficient of variation below 12% were prepared by microchannel (MC) emulsification using a hydrophilic asymmetric straight-through MC silicon 24 × 24 mm microchip consisting of 23,348 microchannels. The stability of the ML stabilized monodisperse emulsion droplets was investigated as a function of CHI addition at various concentration, pH, ionic strength, thermal treatment and freezing-thawing treatment by means of particle size and ζ-potential measurements as well as microscopic observation. The monodisperse O/W emulsions were diluted with CHI solution at various concentrations to a final droplet concentration of 1 wt% soybean oil, 0.25 wt% ML and 0–0.5 wt% CHI at pH 3. Pronounced droplet aggregation was observed when CHI was present at a concentration range of between 0.01 and 0.04 wt%. Above this concentration range, flocculations were less extensive, indicating some restabilization. ML stabilized emulsions were stable at a wide range of NaCl concentrations (0–1000 mM) and pH (3–8). On the contrary, in the presence of CHI, aggregation of the emulsion droplets was observed when NaCl concentration was above 200 mM and when the pH started to approach the pKa of CHI (i.e. ∼6.2–7.0). Emulsions containing CHI were found to have better stability at high temperature (>70 °C) in comparison to the emulsion stabilized only by ML. With sucrose/sorbitol as cryoprotectant aids, emulsions with the addition of CHI were found to be more resistant to droplet coalescence as compared to those without CHI after freezing at −20 °C for 22 h and thawing at 30 °C for 2 h. The use of CHI may potentially destabilize ML-stabilized O/W emulsions but its stability can be enhanced by selectively choosing the appropriate CHI concentrations and conditions of preparation.     

Influence of Ultrasonication Parameters on Physical Characteristics of Olive Oil Model Emulsions Containing Xanthan

Ultrasonic emulsification of 20-wt.% o/w emulsions (pH 3.8) containing a food-grade emulsifier (whey protein isolate, WPI, 2.7 wt.%) and xanthan gum (XG, 0.25 wt.%) was performed. Time and amplitude of ultrasonic treatment changed in order to evaluate their influence on emulsion droplet size, viscosity, and stability (by multiple light scattering (MLS) profiles) during cold storage (10 days at 5 °C). Ultrasonic treatment duration changed from 1 to 4 min at constant amplitude of 70 %. Considering the amplitude, intervals of 40, 60, 80, and 100 % were chosen, for a constant time of 1 min. Similarly, time and amplitude conditions were used to treat solutions of XG of 1 wt.% and evaluate their influence on viscosity and how that was related to the stability of the emulsion. Increase in sonication time from 1 to 4 min led to a significant oil droplet size decrease from 1.14 to 0.89 μm (median droplet diameter). The viscosity of emulsions and XG solutions was highly influenced and considerably decreased with sonication time applied. At those conditions, an increase of backscattering was observed from 58.9 to 72.7 % after 10 days of storage, meaning that more stable emulsions, thinner and of smaller oil droplet size were produced. A similar trend was observed when the amplitude was increased, but droplet size and creaming were always greater than those noticed by changing the sonication time. However, the rate of viscosity, droplet size, and stability change was greater by increasing the amplitude rather than by changing the sonication time.     

Synergistic effects of polyglycerol ester of polyricinoleic acid and sodium caseinate on the stabilisation of water–oil–water emulsions

The inherent thermodynamic instability of water–oil–water (W/O/W) emulsions has restrictions for their application in food systems. The objective of this study was to develop a food grade W/O/W emulsions with high yield and stability using minimal concentrations of surfactants. Emulsions were prepared using soybean oil, polyglycerol ester of polyricinoleic acid (PGPR) alone or in combination with sodium caseinate (NaCN) as emulsifier(s) for primary water-in-oil (W/O) emulsions and NaCN as the sole emulsifier for secondary W/O/W emulsions. Increasing the concentration of PGPR (0.5–8%w/v) had no effect on the droplet sizes of the resulting W/O/W emulsions. However, significant increases in droplet sizes of W/O/W emulsions were observed when the concentration of NaCN in external phase was reduced from 0.5 to 0.03% (w/v) (p<0.05). Percentage yields of emulsions (using a water-soluble dye) improved when PGPR concentration in the inner phase was increased from 0.5 to 8% (w/v). A stable W/O/W emulsion with a yield >90% could be prepared with 4% (w/v) PGPR alone as primary hydrophobic emulsifier and 0.5% (w/v) NaCN as external hydrophilic emulsifier. The concentration of PGPR in the inner phase could be reduced to 2% (w/v) without affecting the yield and stability of the W/O/W emulsion by partially replacing PGPR with 0.5% (w/v) NaCN, which was added to the aqueous phase of the primary W/O emulsion. The results indicate that a possible synergistic effect may exist between PGPR and NaCN, thus allowing formulation of double emulsions with reduced surfactant concentration.     

碱热改性米渣谷蛋白对W/O/W型双重乳液稳定性的影响

目的：实现米渣谷蛋白在乳浊体系中的应用。方法：选取碱热改性米渣谷蛋白和span80,采用一步乳化法制备W/O/W型双重乳液,并考察蛋白浓度对双重乳液稳定性的影响。结果：当蛋白质量分数从0.5%升高至2.5%时,乳液大粒径峰消失,显微结构中液滴的双重结构增强,表观黏度及黏弹性提高,离心稳定性和贮藏稳定性增强。当蛋白质量分数为2.5%时,离心后乳清析出指数从37.21%降至10.56%,分层时间从6 h延长至96 h。蛋白质与span80形成复合膜共同稳定油水界面,形成中间态液滴,当界面蛋白足以形成刚性界面膜时,液滴从中间态转为稳定的双重结构;当蛋白质量分数为3.0%时,双重乳液发生絮凝使大粒径峰重新出现,稳定性下降,离心后乳清析出指数为16.48%,制备后96 h左右分层,过剩的蛋白质一部分参与内相液滴的构建,另一部分单独形成O/W型液滴吸附于大体积液滴外侧。结论：一步乳化法下,蛋白质量分数为2.5%时,可制得稳定双重乳液。     

米糠蛋白O/W及W/O/W乳液制备及界面稳定性

为对比不同米糠蛋白质量浓度下O/W及W/O/W乳液的稳定性,以米糠蛋白作为基料,采用双乳化法制备O/W及W/O/W乳液,考察不同米糠蛋白质量浓度下乳液的微观形态和稳定性并探究其界面稳定机理。结果表明：W/O/W乳液的贮存稳定性显著优于O/W乳液;与相同蛋白含量的O/W乳液相比,W/O/W乳液的黏度显著提高;当米糠蛋白质量浓度为0.4 g/100 mL时,W/O/W乳液的稳定性较O/W乳液提高了1 倍以上;乳液内部包裹更多的W/O液滴,W/O/W乳液的粒径较大;而此时静电斥力也较大,起到稳定乳液的目的。同时,米糠蛋白质量浓度不小于0.4 g/100 mL时,O/W及W/O/W乳液中蛋白质的吸附率较高,达到78%以上。本研究为天然米糠蛋白质在食品级乳液中的开发提供参考,为粮食副产物的综合利用提供了新思路。