Ultradrawing behavior of one- and two-stage drawn gel films of ultrahigh molecular weight polyethylene and low molecular weight polyethylene blends

The ultradrawing behavior of gel films of plain ultrahigh molecular weight polyethylene (UHMWPE) and UHMWPE/low molecular weight polyethylene (LMWPE) blends was investigated using one- and two-stage drawing processes. The drawability of these gel films were found to depend significantly on the temperatures used in the one- and two-stage drawing processes. The critical draw ratio (λ_c) of each gel film prepared near its critical concentration was found to approach a maximum value, when the gel film was drawn at an “optimum” temperature ranging from 95 to 105°C. At each drawing temperature, the one-stage drawn gel films exhibited an abrupt change in their birefringence and thermal properties as their draw ratios reached about 40. In contrast, the critical draw ratios of the two-stage drawn gel films can be further improved to be higher than those of the corresponding single-stage drawn gel films, in which the two-stage drawn gel films were drawn at another “optimum” temperature in the second drawing stage after they had been drawn at 95°C to a draw ratio of 40 in the first drawing stage. These interesting phenomena were investigated in terms of the reduced viscosities of the solutions, thermal analysis, birefringence, and tensile properties of the drawn and undrawn gel films. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 149–159, 1998     

Ultradrawing properties of gel films of ultrahigh‐molecular‐weight polyethylene and low‐molecular‐weight polyethylene blends prepared at various formation temperatures

The ultradrawing behavior of ultrahigh‐molecular‐weight polyethylene/low‐molecular‐weight polyethylene film specimens prepared at various concentrations and formation temperatures was studied. The critical draw ratio (D_rc) of UL_?0.7 film specimens was found to depend significantly on the formation temperature used to prepare the film specimens. At any fixed drawing temperature, the D_rc values of UL_?0.7 specimens prepared at various formation temperatures increased significantly as the formation temperatures were reduced. In fact, with an optimum drawing temperature of 95°C, the D_rc values of UL_?0.7 specimens prepared at a formation temperature of 0°C reached 488, about 50% higher than that of UL_?0.7 specimens prepared at a formation temperature of 95°C. These interesting phenomena were investigated in terms of the thermal, birefringence, and tensile properties of these undrawn and drawn UL_?0.7 specimens. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3728–3738, 2003     

Spinning and drawing properties of ultrahigh‐molecular‐weight polyethylene fibers prepared at varying concentrations and temperatures

The concentrations and temperatures of ultrahigh‐molecular‐weight polyethylene (UHMWPE) gel solutions exhibited a significant influence on their rheological and spinning properties. The shear viscosities of UHMWPE solutions increased consistently with increasing concentrations at a constant temperature above 80°C. Tremendously high shear viscosities of UHMWPE gel solutions were found as the temperatures reached 120–140°C, at which their shear viscosity values approached the maximum. The spinnable solutions are those gel solutions with optimum shear viscosities and relatively good homogeneity in nature. Moreover, the gel solution concentrations and spinning temperatures exhibited a significant influence on the drawability and microstructure of the as‐spun fibers. At each spinning temperature, the achievable draw ratios obtained for as‐spun fibers prepared near the optimum concentration are significantly higher than those of as‐spun fibers prepared at other concentrations. The critical draw ratio of the as‐spun fiber prepared at the optimum concentration approached a maximum value, as the spinning temperature reached the optimum value of 150°C. Further investigations indicated that the best orientation of the precursors of shish‐kebab‐like entities, birefringence, crystallinity, thermal and tensile properties were always accompanied with the as‐spun fiber prepared at the optimum concentration and temperature. Similar to those found for the as‐spun fibers, the birefringence and tensile properties of the draw fibers prepared at the optimum condition were always higher than those of drawn fibers prepared at other conditions but stretched to the same draw ratio. Possible mechanisms accounting for these interesting phenomena are proposed.     

Ultradrawing properties of ultrahigh‐ molecular‐weight polyethylene/carbon nanotube fibers prepared at various formation temperatures

The influence of formation temperature on the ultradrawing properties of ultrahigh‐molecular‐weight polyethylene/carbon nanotube (UHMWPE/CNT) fiber specimens is investigated. Gel solutions of UHMWPE/CNT with various CNT contents were gel‐spun at the optimum concentration and temperature but were cooled at varying formation temperatures in order to improve the ultradrawing and tensile properties of the UHMWPE/CNT composite fibers. The achievable draw ratio (D_ra) values of UHMWPE/CNT as‐prepared fibers reach a maximum when they are prepared with the optimum CNT content and formation temperature. The D_ra value of UHMWPE/CNT as‐prepared fibers produced using the optimum CNT content and formation temperature is about 33% higher than that of UHMWPE as‐prepared fibers produced using the optimum concentration and formation temperature. The percentage crystallinity (W_c) and melting temperature (T_m) of UHMWPE/CNT as‐prepared fiber specimens increase significantly as the formation temperature increases. In contrast, W_c increases but T_m decreases significantly as the CNT content increases. Dynamic mechanical analysis of UHMWPE and UHMWPE/CNT fiber specimens exhibits particularly high α‐transition and low β‐transition, wherein the peak temperatures of α‐transition and β‐transition increase dramatically as the formation temperature increases and/or CNT content decreases. In order to understand these interesting drawing, thermal and dynamic mechanical properties of the UHMWPE and UHMWPE/CNT as‐prepared fiber specimens, birefringence, morphological and tensile studies of as‐prepared and drawn fibers were carried out. Possible mechanisms accounting for these interesting properties are proposed. Copyright © 2010 Society of Chemical Industry     

Ultradrawing behavior of gel films of ultrahigh molecular weight polyethylene and low molecular weight polyethylene blends at varying drawing conditions

A systematic study of the influence of the drawing temperature and rate on the ultradrawing properties of film samples prepared from gel solutions of ultrahigh molecular weight polyethylene and low molecular weight polyethylene blends is reported. At a fixed drawing rate, the achievable draw ratios reached a maximum value when each film specimen was drawn at a temperature near its optimum temperature (T_op). It is interesting to note that the T_op values of each film sample increased consistently with the drawing rate. The achievable draw ratio of each film sample drawn at a constant rate and a temperature near T_op is referred to as the D_raop, which reached another maximum value as the drawing rates approached an optimum value. Dynamic mechanical analysis of the film sample exhibited an extraordinary high transition peaked at temperature near 95°C, which is again very close to the T_op value found for the film sample drawn at a relatively low rate. On the other hand, the birefringence values and tensile strengths of the film specimen were found to improve significantly with the draw ratios, although the improvement of these properties reduced significantly at high draw ratios. Moreover, both the drawing temperature and rate showed beneficial influence on the birefringence, and tensile strengths of the drawn film specimens. Possible mechanisms accounting for these interesting deformation properties are suggested.     

Influence of two‐stage drawing conditions on ultradrawing behavior of gel films of ultrahigh‐molecular‐weight polyethylene and low‐molecular‐weight polyethylene blends

The influence of two‐stage drawing conditions on the ultradrawing behavior of the gel films of ultrahigh‐molecular‐weight polyethylene/low‐molecular‐weight polyethylene blends is reported in this article. The critical draw ratios (λ_c) of the gel films prepared near their critical concentrations were found to depend significantly on the draw ratio attained in the first drawing stage (D_1r) and on the temperature utilized in the second drawing stage (T_sec). After drawing the gel films to a fixed draw ratio in the first drawing stage, each two‐stage drawn gel film was made to exhibit a maximum λ_c (λ_cmax) by drawing the drawn gel film at its corresponding optimum T_sec. In addition, the optimum T_sec was found to increase significantly with the D_1r value of the drawn gel films. It is worth noting, on the other hand, that the λ_cmax of two‐stage drawn gel films increased consistently with an increasing D_1r until its value reached an optimum value of 160. These results clearly suggest that, as T_sec and D_1r are increased to their optimum values, the λ_cmax of the two‐stage drawn gel films can be improved further so as to be higher than those of the corresponding one‐stage drawn gel films. These interesting phenomena were investigated in terms of reduced viscosities of the solutions and by an analysis of the thermal, birefringence, and tensile properties of the drawn gel films. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1890–1901, 2001     

Investigation of the ultradrawing properties of gel spun fibers of ultra‐high molecular weight polyethylene/carbon nanotube blends

The carbon nanotubes (CNTs) contents, ultrahigh‐molecular‐weight polyethylene (UHMWPE) concentrations and temperatures of UHMWPE, and CNTs added gel solutions exhibited significant influence on their rheological and spinning properties and the drawability of the corresponding UHMWPE/CNTs as‐prepared fibers. Tremendously high shear viscosities (ηs) of UHMWPE gel solutions were found as the temperatures reached 140°C, at which their ηs values approached the maximum. After adding CNTs, the ηs values of UHMWPE/CNTs gel solutions increase significantly and reach a maximum value as the CNTs contents increase up to a specific value. At each spinning temperature, the achievable draw ratios obtained for UHMWPE as‐prepared fibers prepared near the optimum concentration are significantly higher than those of UHMWPE as‐prepared fibers prepared at other concentrations. After addition of CNTs, the achievable draw ratios of UHMWPE/CNTs as‐prepared fibers prepared near the optimum concentration improve consistently and reach a maximum value as their CNTs contents increase up to an optimum value. To understand these interesting drawing properties of the UHMWPE and UHMWPE/CNTs as‐prepared fibers, the birefringence, thermal, morphological, and tensile properties of the as‐prepared and drawn fibers were investigated. Possible mechanisms accounting for these interesting properties are proposed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Solid‐state compaction and drawing of nascent reactor powders of ultra‐high‐molecular‐weight polyethylene

The continuous production of ultra‐high‐molecular‐weight polyethylene (UHMWPE) filaments was studied by the direct roll forming of nascent reactor powders followed by subsequent multistage orientation drawing below their melting points. The UHMWPE reactor powders used in this study were prepared by the polymerization of ethylene in the presence of soluble magnesium complexes, and they exhibited high yield even at low reaction temperatures. The unique, microporous powder morphology contributed to the successful compaction of the UHMWPE powders into coherent tapes below their melting temperatures. The small‐angle X‐ray scattering study of the compacted tapes revealed that folded‐chain crystals with a relatively long‐range order were formed during the compaction and were transformed into extended‐chain crystals as the draw ratio increased. Our results also reveal that the drawability and tensile and thermal properties of the filaments depended sensitively on both the polymerization and solid‐state processing conditions. The fiber drawn to a total draw ratio of 90 in the study had a tensile strength of 2.5 GPa and a tensile modulus of 130 GPa. Finally, the solid‐state drawn UHMWPE filaments were treated with O₂ plasma, and the enhancement of the interfacial shear strength by the surface treatment is presented. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 718–730, 2005     

Wetting of oriented and etched ultrahigh molecular weight polyethylene

Highly oriented gel‐spun ultrahigh molecular weight polyethylene (UHMWPE) fibers possess many outstanding properties desirable for composite materials but their adhesion to such matrices as epoxy is poor. This article describes the combined effects of drawing and surface modification on the bulk and surface properties of gel‐cast UHMWPE films emphasizing the effects of etching on both undrawn and drawn films. Drawing the films yields a fibrillar structural hierarchy similar to UHMWPE fibers and a significant increase in orientation, melting point, modulus, and strength. The effects of drawing on bulk properties were more significant than those of etching. The poor adhesion of epoxy to the smooth, fibrillar, and relatively nonpolar drawn film surface improves significantly with oxidization and roughening on etching. The interlaminar shear failure occurred cohesively in the UHMWPE, and thus the interlaminar shear failure strength was greater for the drawn UHMWPE with its greater tensile strength. Nitrogen plasma etching yielded the best results, both removing any low molecular weight surface layer and etching the UHMWPE beneath. Oxygen plasma etching enhanced wetting but was too harsh, causing extensive surface degradation and a significant reduction in mechanical properties. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 405–418, 1999     

Ultrahigh molecular weight polyethylene fibers prepared using conical dies with varying dimensions

Dimensions of conical dies were found to have a significant influence on thermal, morphological, orientation, ultradrawing, and dynamic mechanical properties of the as‐prepared and/or drawn ultrahigh molecular weight polyethylene (UHMWPE) fiber specimens prepared in this study. Many demarcated “micro‐fibrils” were found paralleling to fiber direction of the as‐prepared UHMWPE fiber specimens. The percentage crystallinity, melting temperatures, orientation factor (f_o) and achievable draw ratio (D_ra) values of each as‐prepared UHMWPE fiber specimen prepared at a fixed length of outlet land reach a maximum value, as the entry angles of the conical die approach the optimum value at 75°. The maximum f_o and D_ra values obtained for each F₂₀^75‐y as‐prepared fiber series specimens prepared using the optimum entry angle reach another maximum value as their length of outlet land approach the optimum value of 6.5 mm. The ultimate tensile strengths and moduli of the drawn UHMWPE fibers prepared at the optimum entry angle and length of outlet land are significantly higher than those of fibers prepared at other conditions but stretched to the same draw ratio. Possible reasons accounting for the above interesting properties were discussed in this study. POLYM. ENG. SCI., 2013. © 2013 Society of Plastics Engineers     

Rheological,thermal, and morphological properties of low‐density polyethylene/ultra‐high‐molecular‐weight polyethylene and linear low‐density polyethylene/ultra‐high‐molecular‐weight polyethylene blends

The dynamic rheological behavior of low‐density polyethylene (LDPE)/ultra‐high‐molecular‐weight polyethylene (UHMWPE) blends and linear low‐density polyethylene (LLDPE)/UHMWPE blends was measured in a parallel‐plate rheometer at 180, 190, and 200°C. Analysis of the log–additivity rule, Cole–Cole plots, Han curves, and Van Gurp curves of the LDPE/UHMWPE blends indicated that the blends were miscible in the melt. In contrast, the rheological properties of LLDPE/UHMWPE showed that the miscibility of the blends was decided by the composition of LLDPE. The differential scanning calorimetry results and scanning electron microscopy photos of the LLDPE/UHMWPE blends were consistent with the rheological properties, whereas with regard to the thermal and morphological properties of LDPE/UHMWPE blends, the results reveal three endothermic peaks and phase separation, which indicated a liquid–solid phase separation in the LDPE/UHMWPE blends. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Ultradrawing properties of ultrahigh‐molecular‐weight polyethylene/attapulgite fibers

An investigation of the influence of the contents of original and modified attapulgite (ATP) on the ultradrawing properties of ultrahigh‐molecular‐weight polyethylene (UHMWPE)/ATP (FA_x) and UHMWPE/modified ATP (FA_mx) as‐prepared fibers is reported. Similar to what is found for the orientation factor values, the achievable draw ratios (D_ra) of the FA_x and FA_mx as‐prepared fibers approach a maximum value as the original ATP and/or modified ATP contents reach their corresponding optimum values. The maximum D_ra value obtained for FA_mx as‐prepared fiber specimens is significantly higher than that for FA_x as‐prepared fiber specimens prepared at the optimum original ATP content. Similar to what is found for the orientation factors and achievable drawing properties, the tensile strength (σ_f) and initial modulus (E) of both drawn F₂A_x and F₂A_mx fiber series specimens with a fixed draw ratio reach maximum values as the original and/or modified ATP contents approach the optimum values, respectively. The σ_f and E values of the F₂A_mx fiber specimens are always significantly higher than those of the corresponding F₂A_x fiber specimens prepared at the same draw ratios and ATP contents but without being modified. To understand the interesting ultradrawing, orientation and tensile properties of FA_x and FA_mx fiber specimens, Fourier transform infrared spectral, specific surface area, transmission electron microscopic and elemental analyses of the original and modified ATPs were performed. Copyright © 2012 Society of Chemical Industry     

Evaluation of the tensile properties and thermal stability of ultrahigh‐molecular‐weight polyethylene fibers

The thermal stability of ultrahigh‐molecular‐weight polyethylene (UHMWPE) should be paid attention in its applications, although the fiber has excellent flexible tensile properties. The measurements for two kinds of UHMWPE fibers, Dyneema SK65 (The Netherlands) and ZHF (Beijing, China), were carried out at different annealing temperatures and for different aging times. Experimental and regression analysis results showed that the aging behavior of the fibers followed an exponential attenuation with the annealing temperature and aging time. The critical temperature for the safe use of the fibers was equal to or lower than 70°C and depended on the glass‐transition temperature; this was validated by tensile tests. The difference between the two fibers in the thermal properties resulted from the intrinsic supermolecular structures of the two fibers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 310–315, 2005     

Influence of Drawing Conditions on the Ultradrawing Properties of Film Specimens of Ultrahigh Molecular Weight Polyethylene and Low Molecular Weight Polyethylene Blends

The influence of the drawing temperature and rate on the ultradrawing properties and deformation mechanisms of a series of film specimens prepared from varying concentrations of gel solutions of ultrahigh molecular weight polyethylene (UHMWPE) and low molecular weight polyethylene (LMWPE) blends is reported. The maximum achievable draw ratio was obtained when each UHMWPE/LMWPE film specimen was drawn at an optimum temperature (T _op), wherein the T _op values of each UHMWPE/LMWPE film specimen increased consistently with the drawing rate. The temperature dependence of the apparent elongational viscosity (_a) revealed two distinguishable intervals with different activation energies. Coincidentally, the transition temperature (T _r) obtained from the intersection of the two straight lines drawn parallel to the two distinct intervals is approximately equal to the T _op value found for the film sample drawn at the same rate. Dynamic mechanical analysis of the film samples exhibited an extraordinary high transition peaked at temperatures near 95–115C, which are again very close to the T _op and T _r values found for the film samples drawn at varying rates, and increases significantly with the testing frequencies. Possible mechanisms accounting for these interesting deformations, temperature dependence of the apparent elongational viscosity and dynamic mechanical properties are suggested in this study.     

Free radical activity in gamma‐irradiated polyethylene film,drawn tape and ultra‐high‐modulus fibres determined by grafting performance

Grafting rates of gaseous butadiene to a range of morphological forms of gamma‐irradiated polyethylene, including ultra‐high‐modulus fibres (UHMPE), have been measured in order to determine the availability of active free radicals over time at various temperatures. Blank experiments on unirradiated samples showed that monomer diffusion is not rate‐controlling with film and natural draw ratio tapes, but is likely to be a major factor in the control of grafting rates in UHMPE fibres. Grafting rates from monomer loss/time experiments with irradiated samples indicate that grafting is always in competition with free radical self‐annihilation, the extent being influenced by temperature, dose and morphology, including prior sample annealing. At lower temperatures, graft‐active radicals are produced over long periods of time, eg close to linear grafting rates were monitored over 20 hours for PE tape at 0 °C (50 kGy) and for gel‐spun UHMPE at 40 °C (100 kGy). At higher temperatures, grafting rates steadily decrease with time. Grafting rates are almost independent of irradiation dose in the early stages, however, the dose has an increasing positive influence as the reaction proceeds. At any given temperature and irradiation dose, the rates decrease in the series undrawn film; natural draw ratio tape; high draw ratio gel‐spun fibre; high draw ratio melt‐spun fibre. An analogy is drawn between these results and the optimum conditions required for improving the creep properties of PE tape and UHMPE fibres by acetylene‐sensitized irradiation crosslinking. Copyright © 2005 Society of Chemical Industry     

Ultradrawing properties of ultrahigh‐molecular weight polyethylene/functionalized carbon nanotube fibers and transmittance properties of their gel solutions

The influences of the dispersion level of carbon nanotubes (CNTs) and functionalized CNTs on the transmittance properties of ultrahigh‐molecular weight polyethylene (UHMWPE) gel solutions and on ultradrawing properties of their as‐prepared fibers are reported. The transmittance properties suggest that the dispersion level of functionalized CNTs in UHMWPE/functionalized CNTs gel solution is significantly better than plain CNTs in UHMWPE/CNTs gel solutions. The orientation factors, achievable draw ratios, tensile strength (σ_f), and modulus (E) values of UHMWPE/CNTs (F_xC_y) and UHMWPE/functionalized CNTs (F_xC_f‐y) as‐prepared fiber specimens reached a maximum value as their CNT and functionalized CNT contents approached optimum contents at 0.00015 and 0.0001 wt%, respectively. The σ_f and E values of both F_xC_0.0012 and F_xC_f‐0.001 series fiber specimens prepared at their optimum CNT and functionalized CNT contents reached another maximum as their UHMWPE approached optimum UHMWPE concentration of 1.7 wt%. Possible reasons accounting for these interesting properties are proposed. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Injection molding of delamination‐free ultra‐high‐molecular‐weight polyethylene

When ultra‐high‐molecular‐weight polyethylene (UHMWPE) in powder form is injection molded, the so‐called delamination layering occurs near the skin of the parts. This layering defect hampers UHMWPE's superior wear resistance property and part surface quality. The delamination layer was caused by a combination of excessive shear stress near the part surface and high degree of molecular entanglement of UHMWPE. A mold insulation method that delays the rapid cooling of UHMWPE to reduce the shear stress and improve the polymer chain “interdiffusion” across the entangled chain bundles was used to eliminate the delamination layer. When the insulation layer thickness and mold temperature were optimized, the delamination layer was eliminated completely while still maintaining a reasonable cooling/cycle time. The delamination‐free parts were found to regain UHMWPE's superior impact resistance and tensile properties. POLYM. ENG. SCI., 59:2313–2322, 2019. © 2019 Society of Plastics Engineers     

Surface modification of ultra‐high‐molecular‐weight polyethylene. I. Characterization and sintering studies

We performed surface modification of ultra‐high‐molecular‐weight polyethylene (UHMWPE) through chromic acid etching with the aim of improving the performance of UHMWPE's composites with poly(ethylene terephthalate) fibers. In part I of this study, we evaluated the effects of chemical modification on the surface properties of UHMWPE with X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), and contact angle measurements. The thermal properties, rheology, and sintering behavior of the modified UHMWPE were compared to those of the base material. XPS and FTIR analysis confirmed the presence of carboxyl and hydroxyl groups on the surface of the modified powders. The substitution of polar groups into the backbone of the polymer decreased its contact angles with water and hexadecane and increased its surface energy, as evidenced by contact angle measurements. The modified UHMWPE was more crystalline than the base resin and less prone to thermal degradation. Although the rheological properties were virtually identical, the modified powders sintered more readily, presumably due to their higher surface energy, which suggested enhanced processability by compression molding. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Ultradrawing properties of ultra‐high molecular weight polyethylene/functionalized carbon nanotube fibers

Systemic investigation of the influence of the plain and functionalized carbon nanotube (CNT) contents on the ultradrawing properties of ultrahigh molecular weight polyethylene/carbon nanotubes (UHMWPE/CNTs, FC_y) and UHMWPE/functionalized CNTs (FC_fx‐y) as‐prepared fibers are reported. In a way similar to those found for the orientation factor values, the achievable draw ratios (D_ra) of the FC_y and FC_fx‐y as‐prepared fibers approached a maximum value as their CNT and/or functionalized CNT contents reached their corresponding optimum values. The maximum D_ra values obtained for FC_fx‐0.001 as‐prepared fiber specimens prepared at varying maleic anhydride grafted polyethylene (PE_‐g‐MAH)/modified CNTs weight ratios were significantly higher that of the FC_0.0015 as‐prepared fiber specimen prepared at the optimum plain CNT content. Tensile property analysis further suggested that excellent orientation and tensile properties of the drawn FC_y and FC_fx‐y fibers can be obtained by ultradrawing the fibers prepared at their optimum plain CNT and/or functionalized CNT contents. To understand the interesting orientation, ultradrawing and tensile properties of FC_y and FC_fx‐y fiber specimens, FTIR, specific surface area, and SEM morphology analysis of the plain and functionalized CNTs were performed in this study. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers     

Influence of different sterilization procedures on the morphological parameters and mechanical properties of ultra‐high‐molecular‐weight polyethylene

The objectives of this study were to examine the effects of the processing conditions, sterilization, and thermal treatment on the morphological and mechanical properties of ultra‐high‐molecular‐weight polyethylene (UHMWPE) in medical applications by means of thermal analysis, Fourier transform infrared spectroscopy, and nanoindentation. It is well known that manufacturing, irradiation, and thermal treatments significantly alter the microstructure of materials, which results in changes in their mechanical properties. UHMWPE was found to be barely sensitive to processing conditions but strongly influenced by sterilization treatments. Great emphasis was given to the characterization of the so‐called first generation of highly crosslinked UHMWPE because the thermal history of this material differed from that of γ‐irradiated materials. The physical and mechanical properties of UHMWPE were influenced as a result of γ and electron‐beam irradiation and the remelting procedure. Lower crystallinity, different lamellar thickness distributions, and lower hardness and modulus values were estimated. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011