Effect of a small amount of poly(3‐hydroxybutyrate) on the crystallization behavior of poly(l‐lactic acid) in their immiscible and miscible blends during physical aging

The miscibility and effect of physical aging on the crystallization behavior of poly(l ‐lactic acid) (PLLA)/poly(3‐hydroxybutyrate) (PHB) blends with a small amount of PHB (≤10 wt%) have been investigated using differential scanning calorimetry and Fourier transform infrared spectroscopy. It is found that the miscibility of PLLA/PHB blends with a very small percentage of PHB can be modulated by varying the molecular weight of the PHB. That is, a PLLA/PHB blend with low‐molecular‐weight PHB is miscible, whereas that with high‐molecular‐weight PHB is immiscible. It is found that physical aging at temperatures far below the glass transition temperature can promote the cold crystallization kinetics of PLLA in PLLA/PHB blends with high‐molecular‐weight PHB rather than in those with low‐molecular‐weight PHB. These findings suggest that the effect of physical aging on the crystallization behavior of the main component in a crystalline/crystalline blend with a small percentage of the second component is strongly dependent on the miscibility of the blend system. Enhanced chain mobility of PLLA in the interface region of PLLA matrix and PHB micro‐domains is proposed to explain the physical aging‐enhanced crystallization rate in immiscible PLLA/PHB blends with high‐molecular‐weight PHB. © 2013 Society of Chemical Industry     

The synthesis of poly(3‐hydroxybutyrate)‐g‐poly(methylmethacrylate) brush type graft copolymers by atom transfer radical polymerization method

Brush type of poly (3‐hydroxy butyrate), PHB, copolymer synthesis has been reported. Natural PHB was chlorinated by passing chlorine gas through PHB solution in CHCl₃/CCl₄ mixture (75/25 v/v) to prepare chlorinated PHB, PHB‐Cl, with the chlorine contents varying between 2.18 and 39.8 wt %. Toluene solution of PHB‐Cl was used in the atom transfer radical polymerization (ATRP) of methyl methacrylate, MMA, in the presence of cuprous bromide (CuBr)/2,2′‐bipyridine complex as catalyst, at 90°C. This “grafting from” technique led to obtain poly (3‐hydroxybutyrate)‐g‐poly(methylmethacrylate) (PHB‐g‐PMMA) brush type graft copolymers (cylindrical brush). The polymer brushes were fractionated by fractional precipitation methods and the γ values calculated from the ratio of the volume of nonsolvent to volume of solvent of brushes were ranged between 2.8 and 9.5 depending on the molecular weight, grafting density, and side chain length of the brushes, while the γ values of PHB, PHB‐Cl, and homo‐PMMA were 2.7–3.8, 0.3–2.4, and 3.0–3.9, respectively. The fractionated brushes were characterized by gel permeation chromatography, ¹H‐NMR spectrometry, thermogravimetric analysis (TGA), and differential scanning calorimetry techniques. PHB‐g‐PMMA brush type graft copolymers showed narrower molecular weight distribution (mostly in range between 1.3 and 2.2) than the PHB‐Cl macroinitiator (1.6–3.5). PHB contents in the brushes were calculated from their TGA thermograms and found to be in range between 22 and 42 mol %. The morphologies of PHB‐g‐PMMA brushes were also studied by scanning electron microscopy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Miscibility of block copolymers of poly(ε‐caprolactone) and poly(ethylene glycol) with poly(3‐hydroxybutyrate) as well as the compatibilizing effect of these copolymers in blends of poly(ε‐caprolactone) and poly(3‐hydroxybutyrate)

Atactic poly(3‐hydroxybutyrate) (a‐PHB) and block copolymers of poly(ethylene glycol) (PEG) with poly(ε‐caprolactone) (PCL‐b‐PEG) were synthesized through anionic polymerization and coordination polymerization, respectively. As demonstrated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) measurements, both chemosynthesized a‐PHB and biosynthesized isotactic PHB (i‐PHB) are miscible with the PEG segment phase of PCL‐b‐PEGs. However, there is no evidence showing miscibility between both PHBs and the PCL segment phase of the copolymer even though PCL has been block‐copolymerized with PEG. Based on these results, PCL‐b‐PEG was added, as a compatibilizer, to both the PCL/a‐PHB blends and the PCL i‐PHB blends. The blend films were obtained through the evaporation of chloroform solutions of mixed components. Excitingly, the improvement in mechanical properties of PCL/PHB blends was achieved as anticipated initially upon the addition of PCL‐b‐PEG. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2600–2608, 2001     

Poly(ethylene glycol)‐modulated cellular biocompatibility of polyhydroxyalkanoate films

Polyhydroxybutyrate (PHB) and its copolymer with hydroxyvalerate, P(HB‐co‐HV), are widely used biomaterials. In this study, improvements of their biological properties of degradability and compatibility were achieved by blending with low‐molecular‐weight poly(ethylene glycol) (PEG106) approved for medical use. Surface morphology and chemistry are known to support cell attachment. Attachment and proliferation of neural olfactory ensheathing cells increased by 17.0 and 32.2% for PHB and P(HB‐co‐HV) composite films. Cell attachment was facilitated by increases in surface hydrophilicity, water contact angles decreased by 26 ± 2° and water uptake increased by 23.3% depending upon biopolymer and PEG loading. Cells maintained high viability (>95%) on the composite films with no evidence of cytotoxic effects. Assays of mitochondrial function and cell leakage showed improved cell health as a consequence of PEG loading. The PEG component was readily solubilised from composite films, allowing control of degradation profiles in the cell growth medium. Promotion of biopolymer compatibility and degradability was not at the expense of material properties, with the extension to break of the composites increasing by 5.83 ± 1.06%. Similarly, crystallinity decreased by 36%. The results show that blending of common polyhydroxyalkanoate biomaterials with low‐molecular‐weight PEG can be used to promote biocompatibility and manipulate physiochemical and material properties as well as degradation.© 2013 Society of Chemical Industry     

Effect of PEG additives on properties and morphologies of membranes prepared from poly(2,6‐dimethyl‐1,4‐phenylene oxide) by benzyl bromination and in situ amination

This study investigated the effect of PEG additive on the structure formation and permeation properties of membranes. The membranes were prepared from a bromomethylated poly(2,6‐dimethyl‐1,4‐phenylene oxide)/chlorobenzene/ethanol system using the phase inversion method with PEG as an additive. As expected, PEG with a fixed molecular weight (e.g., PEG 600) acted as a pore‐forming agent, and membrane porosity increased as the PEG content of the casting solution increased. However, when the PEG content was fixed, the effect of PEG on the membrane properties and morphology was largely dependent on its molecular weight. It was found that when the molecular weight of PEG was less than 800, it acted as a pore former, but when the molecular weight of PEG was more than 1000, the pore size and porosity of the resulting membrane decreased. These results can be explained by the membrane‐forming system's thermodynamic and kinetic properties, which can be assessed by coagulation value and viscosity. Furthermore, the membranes were characterized for pure water flux and rejection of solute and by SEM observation. The filtration results agreed well with the SEM observations. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2414–2421, 2005     

Fast crystallization of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) with talc and boron nitride as nucleating agents

The crystallization behavior of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) induced by two kinds of nucleating agents, boron nitride (BN) and talc, was investigated by differential scanning calorimetry, polarized optical microscopy and X‐ray diffraction. Both BN and talc have good nucleating ability in the crystallization of PHB and PHBV. From these results, combined with molecular weight measurement by gel permeation chromatography, the mechanism of nucleation by BN and talc in the crystallization of PHB and PHBV has been proposed. BN acts as a nucleating agent itself and initiates nucleation in the crystallization of PHB and PHBV. Talc acts in a different way. It reacts as a chemical reagent with the molten chains of PHB/PHBV, while the reaction product acts as the true nucleating agent, which lowers the crystallization barriers of PHB and PHBV. ¹H NMR spectroscopy provides evidence for the reaction between PHB and talc and supports the proposed nucleation mechanism. Copyright © 2005 Society of Chemical Industry     

Synthesis of polyblends from polypropylene and poly(R,S)‐β‐hydroxybutyrate,and their characterization

Blends of modified polypropylene (PP) with poly(R,S)‐β‐hydroxybutyrate (PHB) were prepared by casting polymer solutions, followed by compression molding into thin films. The modified polypropylene was obtained by oxidation with hydrogen peroxide. Oxidation of polypropylene produced new functional groups such as carbonyl and hydroxyl groups on the polymer chain, and a decrease in molecular weight and crystallinity of the polymers. Maximum crystallinity and mechanical properties of the polyblends were found with a PP/PHB ratio of 90/10 (w/w), and then decreased with increasing PHB content in the polyblends. Biodegradability of the polyblends was lower than that of bacterial and synthetic PHBs. Furthermore, an increase of PHB proportion in the polyblends resulted in highly non‐compatible polyblends. Hence only PHB and small parts of the polyblends were decomposed by microorganisms. Copyright © 2006 Society of Chemical Industry     

Production and characterization of films containing poly(hydroxybutyrate) (PHB) blended with esterified alginate (ALG‐e) and poly(ethylene glycol) (PEG)

Alternative materials have long been studied and developed to replace conventional skin dressings with the emergence of new biopolymers and development of polymeric film fabrication techniques. As a new material for polymeric dressings, films of poly(hydroxybutyrate) (PHB) blended with esterified alginate (ALG‐e) and poly(ethyleneglycol) was studied. The esterification of sodium alginate (ALG‐e) generated a material with some amphiphilic characteristics and increased compatibility with the PHB. PEG was added as plasticizer in PHB/ALG‐e films was also tested, since PEG is often used in blends with PHB to improve flexibility and reduce hydrophobicity. At the amounts studied, it was found that both PEG and ALG‐e increase the degree of crystallinity, but a decrease was observed in the hydrophobic nature of PHB films. At the maximum concentration of ALG‐e and PEG used an increase in water vapor permeability and a decrease in tensile strength was reached due to the synergistic effect caused by better homogenization of PEG and ALG‐e in the PHB matrix. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44362.     

Preparation of cellulose acetate butyrate and poly(ethylene glycol) copolymer to blend with poly(3‐hydroxybutyrate)

A two‐step procedure was used to synthesize the cellulose acetate butyrate and poly(ethylene glycol) graft copolymer (CAB‐g‐PEG). By choosing the appropriate composition, the crosslinked graft copolymer or not could be obtained. Then, the CAB‐g‐PEG copolymer was blended with poly(3‐hydroxybutyrate) (PHB), to further improve the mechanical properties of PHB. The results indicated that PHB and CAB‐g‐PEG that were not crosslinked were miscible over the entire composition range. As the CAB‐g‐PEG copolymer increased in the PHB/CAB‐g‐PEG blends, the melting temperature of the blends decreased, the crystallization of PHB became more difficult, and the crystallinity of the blend and PHB phase all decreased. The tensile properties and impact strength of the PHB/CAB‐g‐PEG blends were superior to the PHB/CAB blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1471–1478, 2006     

Synthesis and characterization of a novel poly(ester‐urethane) containing short lactate sequences and PEG moieties

A novel poly(ester‐urethane) with tailor‐made structure was prepared by using lactic acid (LA) as starting material through a combination of two facile common reactions. First, a diol was prepared via the esterification between LA and poly(ethylene glycol) (PEG) with low molecular weight. Subsequently, the poly(ester‐urethane) was synthesized through the addition polymerization of the LA‐based diol and toluene 2,4‐diisocyanate with 1,4‐butanediol as chain extender. The structure, morphology, and properties of intermediate and the poly(ester‐urethane) were analyzed with Fourier transform infrared spectroscopy, proton nuclear magnetic resonance, gel permeation chromatography (GPC), X‐ray diffraction, differential scanning calorimetry, polarizing optical microscopy, and thermogravimetric analysis. The results indicated that the intermediate was a diol of conjugating quite short lactate sequences with PEG oligomer, and the structure of the poly(ester‐urethane) was as expected. The thermal transition, thermal decomposition temperature, and crystallinity of the polymer samples depended on the molecular size of PEG. In vitro degradation property of the poly(ester‐urethane) also relied on the molecular weight of PEG. The weight loss percentages varied from 11 to 36% after 12‐days immersing in phosphate‐buffer saline at 37°C. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Poly(ethylene glycol) derivatives containing periodic side‐chain carboxyl groups: synthesis and characterization

The aim was the synthesis of chain‐extended poly(ethylene glycol) (PEG) derivatives containing periodic side‐chain carboxyl groups. The chain extension of PEG diols with pyromellitic dianhydride was performed in toluene or dimethylformamide solution and in bulk. The degree of chain extension (DoCE) was between 6 and 21, the highest value being recorded when the reaction was performed using low‐molecular‐weight PEG. The recorded limited increase of molecular weight could be at least partially attributed to the rather low reactivity of the aromatic dianhydride. To overcome this issue, a more reactive aliphatic dianhydride, ethylenediaminetetraacetic dianhydride (EA), was tested. However, the reaction of PEG with EA only afforded a DoCE of 2.5. Appreciably higher DoCE values were obtained when EA was reacted with bisamino‐terminated PEG. Independent of prepolymer and dianhydride structure, all chain‐extended products displayed less of a tendency to crystallization than the starting prepolymer, very likely due to interference by anhydride residues. The low in vitro cytotoxicity of the chain‐extended polymers and the presence of carboxyl groups point to their possible use in biomedical applications, particularly in controlled drug release and tissue engineering. © 2014 Society of Chemical Industry     

Rheology of poly(N‐vinyl pyrrolidone)–poly(ethylene glycol) adhesive blends under shear flow

The rheological properties of adhesive miscible blends of high‐molecular‐weight poly(N‐vinyl pyrrolidone) (PVP) with short‐chain poly(ethylene glycol) (PEG) under oscillatory and steady‐state shear flow have been examined with dynamic mechanical and squeezing‐flow analysis. The latter allows the rheological characterization of adhesive blends under conditions modeling adhesive‐bond formation as a fixed compressive force is applied to an adhesive film. The most adhesive PVP blend with 36 wt % PEG has been established to flow like a viscoplastic (yield stress) liquid with a power‐law index of about 0.12. The study of the apparent yield stress as a function of the PVP–PEG composition, content of sorbed water, molecular weight of PVP, and temperature shows that the occurrence of a yield stress in the blends results most likely from a noncovalent crosslinking of PVP macromolecules through short PEG chains by means of hydrogen bonding of both terminal OH groups of PEG to the complementary functional groups in PVP monomer units. A molecular mechanism of PVP–PEG interaction was established earlier by direct and independent methods. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 522–537, 2006     

Dispersion,crystallization behavior,and mechanical properties of poly(3-hydroxybutyrate) nanocomposites with various silica nanoparticles: effect of surface modifiers

Silica nanoparticles (NPs) with various surface properties were introduced in poly(3-hydroxybutyrate) (PHB) matrix and the their effect on the dispersion, crystallization behavior, and reinforcement in the nanocomposites was discussed in this article. Two kinds of commercial fumed silica NPs and two kinds of self-prepared sol-gel silica (bare and PEGylated) NPs were used. The cross-sectional SEM (scanning electron microscopy) images, provided the micrometer scale view (observation area: 12.6×8.2 μm²), showed that commercial fumed silica and PEG–silica NPs were aggregated and well-dispersed in PHB matrix, respectively. Similarly, Morisita’s analysis of TEM (transmission electron microscopy) images (observation area: 2.4×1.6 μm²) indicated that PEG-silica NPs were Poisson dispersed and commercial fumed silica NPs were serious aggregated in PHB matrix. However, SEM-EDX (energy dispersive X-ray analysis) Si-mapping micrographs, provided the millimeter scale view (observation area: 0.79×0.61 mm²), showed that four kinds of silica NPs were well-dispersed in PHB matrix. PLM (polarized light microscopy) images indicated that spherulite growth rate and morphology of PHB did not change obviously upon the addition of various silica NPs, except the PHB/PEG–silica system. PHB/PEG–silica showed a decreased spherulite growth rate, which was consistent with the DSC (differential scanning calorimetry) results, because the good miscibility between PHB and the grafted PEG chains on PEG–silica could decrease the polymer chain mobility during crystallization. The Young’s modulus and tensile strength of the PHB were enhanced by up to 34% and 63% by adding a small amount of PEG–silica. Fully well-dispersed PEG–silica NPs functioned as physical cross-linking centers for enhancing the mechanical properties of PHB but as retarding agents for reducing the crystallization rate.     

Synthesis and characterization of biodegradable poly(ester‐urethanes) based on bacterial poly(R‐3‐hydroxybutyrate)

A series of poly(R‐3‐hydroxybutyrate)/poly(ε‐caprolactone)/1,6‐hexamethylene diisocyanate‐segmented poly(ester‐urethanes), having different compositions and different block lengths, were synthesized by one‐step solution polymerization. The molecular weight of poly(R‐3‐hydroxybutyrate)‐diol, PHB‐diol, hard segments was in the range of 2100–4400 and poly(ε‐caprolactone)‐diol, PCL‐diol, soft segments in the range of 1080–5800. The materials obtained were investigated by using differential scanning calorimetry, wide angle X‐ray diffraction and mechanical measurements. All poly(ester‐urethanes) investigated were semicrystalline with T_m varying within 126–148°C. DSC results showed that T_g are shifted to higher temperature with increasing content of PHB hard segments and decreasing molecular weight of PCL soft segments. This indicates partial compatibility of the two phases. In poly(ester‐urethanes) made from PCL soft segments of molecular weight (M_n ≥ 2200), a PCL crystalline phase, in addition to the PHB crystalline phase, was observed. As for the mechanical tensile properties of poly(ester‐urethane) cast films, it was found that the ultimate strength and the elongation at the breakpoint decrease with increasing PHB hard segment content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 703–718, 2002     

Structure‐property relationship of L‐tyrosine‐based polyurethanes for biomaterial applications

The structure‐property relationship of L ‐tyrosine‐based polyurethanes was demonstrated by using different polyols and diisocyanates. L ‐tyrosine‐based chain extender, desaminotyrosyl tyrosine hexyl ester (DTH), was used to synthesize a series of polyurethanes. Polyethylene glycol (PEG) or poly caprolactone diol (PCL) was used as the soft segment and hexamethylene diisocyanate (HDI) or dicyclohexylmethane 4,4′‐diisocyanate (HMDI) was used with DTH as the hard segment. The polyurethanes were characterized to investigate the effect of structure on different polyurethane properties. From FTIR and DSC, these polyurethanes exhibit a wide range of morphology from phase‐mixed to phase‐separated structure. The decreasing molecular weight of the PEG soft segment leads to relatively more phase mixed morphology whereas for PCL‐based polyurethanes the extent of phase mixing is less with decreasing PCL molecular weight. Results show that PCL‐based polyurethanes are mechanically stronger than PEG‐based polyurethanes but PCL‐based polyurethanes degrade slower and absorb less water compared with PEG‐based polyurethanes. The HMDI‐based polyurethanes are less crystalline and comparatively more hydrophobic than HDI‐based polyurethanes. The characterization results show that the polyurethane properties are directly related to the structure and can be varied easily for a different set of properties that are pertinent for biomaterial applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal degradation of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) in drying treatment

This study examines the isothermal treatment of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) powders and films. The PHB and PHBV crystallinities were determined using X‐ray diffractometry, and shown to increase with temperature (130–150°C) and then decreased from 55% to 45% at 180°C. The crystal morphology of crystal planes (101) and (111) became sharp at a high temperature. The weight average molecular weight (M_w) of PHB decreased from 1,028,000 to 41,800 g/mol when heated at 180°C for 30 min. The molecular weight of PHB decreased more rapidly than that of PHBV with time. No peak signal was observed in gel permeation chromatography after heating at 150°C because the solubility of PHB changed with crystallinity. The thermal behaviors of PHB and PHBV were analyzed by differential scanning calorimetry and thermogravimetric analysis. The roughness, contact angle, and surface morphology of PHB and PHBV films were also measured to determine the surface properties. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3659–3667, 2013     

Formation of microcapsules of medicines by the rapid expansion of a supercritical solution with a nonsolvent

The rapid expansion from a supercritical solution with a nonsolvent (RESS‐N) was applied to the formation of polymeric microcapsules containing medicines such as p‐acetamidophenol, acetylsalicylic acid, 1,3‐dimethylxanthine, flavone, and 3‐hydroxyflavone. A suspension of medicine in carbon dioxide (CO₂) containing a cosolvent and dissolved polymer was sprayed through a nozzle to atmospheric pressure. The pre‐expansion pressure was 10–25 MPa, and the temperature was 308–333 K. The polymers were poly(L ‐lactic acid) (molecular weight = 5000), poly(ethylene glycol) (PEG; PEG4000, molecular weight = 3000; PEG6000, molecular weight = 7500; and PEG20000, molecular weight = 20,000), poly(methyl methacrylate) (molecular weight = 15,000), ethyl cellulose (molecular weight = 5000), and PEG–poly(propylene glycol)–PEG triblock copolymer (molecular weight = 13,000). The solubilities of the polymers as coating materials and these medicines as core substance were very low in CO₂. However, the solubilities of these polymers in CO₂ significantly increased with the addition of low molecular weight alcohols as cosolvents. After RESS‐N, polymeric microcapsules were formed according to the precipitation of the polymer caused by a decrease in the solvent power of CO₂. This method offered three advantages: (1) enough of the coating polymers, which were insoluble in pure CO₂, dissolved; (2) the microparticles of the medicine were encapsulated without adhesion between the particles because a nonsolvent was used as a cosolvent and the cosolvent remaining in the mixture was removed by the gasification of CO₂; and (3) the polymer‐coating thickness was controlled with changes in the feed composition of the polymer for drug delivery. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 742–752, 2003     

Preparation of well‐defined block copolymer having one polystyrene segment and another poly(styrene‐alt‐maleic anhydride) segment with RAFT polymerization

Block copolymers, polystyrene‐b‐poly(styrene‐co‐maleic anhydride), have been prepared by reversible addition‐fragmentation chain transfer (RAFT) polymerization technique using three different approaches: 1‐phenylethyl phenyldithioacetate (PEPDTA) directly as RAFT agent, mediated polystyrene (PS) block as the macromolecular PS‐RAFT agent and mediated poly(styrene‐maleic anhydride) (SMA) block with alternating sequence as the macromolecular SMA‐RAFT agent. Copolymers synthesized in the one‐step method using PEPDTA as RAFT agent possess one PS block and one SMA block with gradient structure. When the macromolecular RAFT agents are employed, copolymers with one PS block and one alternating SMA block can be produced. However, block copolymers with narrow molecular weight distribution (MWD) can only be obtained using the PS‐RAFT agent. The MWD deviates considerably from the typical RAFT polymerization system when the SMA is used as the RAFT agent. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Biodegradable natural composites. II. Synergistic effects of processing cellulose with PHB

This article reports on the synergistic effects observed during the processing of cellulose with bacteria-produced polyhydroxybutyrate (PHB). Cellulose fibers processed with PHB-melt exhibited defibrillation as shown by SEM. Microscopic studies of extracted fibers demonstrated that a dramatic fiber-size reduction occurred during processing. The size reduction was related to the degree of processing, which, we believe, depended on the amount of crotonic acid produced during thermal degradation of PHB. Size exclusion chromotography (SEC) studies of PHB samples thermally treated under well-defined conditions showed a decrease in molecular weight as a function of treatment time. The samples processed with and without cellulose were analyzed for their molecular weight, and the processing of cellulose was found to contribute to a greater amount of chain scission, plausibly caused by local overheating as a result of shear forces developed during processing. Thermogravimetric studies performed isothermally on PHB under various temperatures gave correlations between the amount of volatile products and the molecular weight reduction of PHB. These findings confirmed our hypothesis on in situ formation of acid during melt processing of PHB and hydrolysis of cellulose fibers by such an acid during compounding. © 1994 John Wiley & Sons, Inc.     

Effect of poly(ethylene glycol) on the solid‐state polymerization of poly(ethylene terephthalate)

Poly(ethylene glycol) (PEG) and end‐capped poly(ethylene glycol) (poly(ethylene glycol) dimethyl ether (PEGDME)) of number average molecular weight 1000 g mol^?1 was melt blended with poly(ethylene terephthalate) (PET) oligomer. NMR, DSC and WAXS techniques characterized the structure and morphology of the blends. Both these samples show reduction in T_g and similar crystallization behavior. Solid‐state polymerization (SSP) was performed on these blend samples using Sb₂O₃ as catalyst under reduced pressure at temperatures below the melting point of the samples. Inherent viscosity data indicate that for the blend sample with PEG there is enhancement of SSP rate, while for the sample with PEGDME the SSP rate is suppressed. NMR data showed that PEG is incorporated into the PET chain, while PEGDME does not react with PET. Copyright © 2005 Society of Chemical Industry