Abrasive wear resistance of spheroidal vanadium carbide cast irons

The effect of the chemical composition and heat treatment on the microstructure and abrasive wear resistance of V-Mn, V-Ni-Cr, and V-Mo spheroidal vanadium carbide cast irons (18–23 vol %) has been studied. The wear resistance has been determined under conditions of wear by abrasives with various hardnesses, i.e., corundum and quartz and compared to that of high-chromium cast iron with 13% Cr. It has been found that the advisability of using high-vanadium cast irons is governed by the hardness of the abrasive. When a hard abrasive, i.e., corundum was used, V-Mo cast iron with the maximum concentration of spheroidal VC carbides, which were uniformly distributed in the martensitic matrix, had the highest wear resistance. When a soft abrasive, i.e., quartz, was applied, high-chromium cast iron with a hardness of 68 HRC, which contained the largest amount of M₇C₃ carbides, was more wear-resistant. In the course of isothermal exposure at 300–1000°C, V-Ni-Cr and V-Mo cast irons with an austenitic structure had high resistance to phase and structural transformations. However, the properties and microstructure of V-Mo cast irons with a martensitic matrix depended strongly on the temperature of exposure during heat treatment.     

Influence of abrasive hardness on the wear resistance of high chromium irons

The resistance to abrasive wear was determined for a series of alloyed white cast irons in a high stress abrasion test which utilizes a specimen in sliding contact with bonded abrasives. These were conducted on silicon carbide, alumina and two sizes of garnet abrasive.The results indicate that the hardness, or type, of abrasive used in the test significantly influenced the wear rate of white irons, i.e. the rate of wear increased with increasing hardness of the abrasive. Also, the results indicate that the type of abrasive used in the test was a significant factor in ranking white irons for resistance to high stress abrasion. When tested on silicon carbide or alumina abrasive, as-cast austenitic irons exhibited lower rates of wear than heat treated martensitic irons; when tested on garnet, an abrasive of lower hardness, those irons with martensitic matrix microstructures exhibited the same or less wear than irons with austenitic matrix microstructures. It was also evident that heat treated irons with martensitic matrix microstructures exhibited varying degrees of resistance to abrasive wear depending on cooling rates and alloy content.     

Cr/C对含4%Ni高铬耐磨耐蚀铸铁性能的影响

采用对比试验的方法探讨了不同Cr/C的比值对含4%Ni高铬耐磨耐蚀铸铁硬度、耐磨性及冲击韧性的影响规律。结果表明:无论固定C还是固定Cr,改变Cr/C的比值对4%Ni高铬耐磨耐蚀铸铁性能都有显著的影响,尤其当含C量较低时,Cr的变化对材料性能的影响更明显。通过调整不同的Cr/C,可以获得不同的硬度、耐磨性和冲击韧性组合的材料。     

马氏体球墨铸铁腐蚀磨损特性研究

对马氏体球墨铸铁在不同pH值石英砂浆中的静载三体腐蚀磨损特性进行了试验研究,并与铬白口铸铁进行了对比。结果表明：无论在静栽三体磨料磨损或静载三体腐蚀磨损中,马氏体球置铸铁均优于低铬白口铸铁。适当提高含硅量,有利于提高腐蚀耐磨损性,而且在酸性砂浆中效果较明显。     

铸铁在烧碱中腐蚀行为的研究

通过试验,对铸铁在烧大事中的腐蚀行为做了系统的研究。铸铁的金相组织对其耐碱蚀中能提高耐蚀性,而在应力腐蚀中则相反。石墨形态对铸铁在烧碱中的全面腐蚀性能无明显影响,在应力腐蚀条件下它常成为裂纹源。铸铁烧碱体系钝化时,维钝电流大小可预测铸铁的全面腐蚀性能。试验证明,慢应变速率技术（SSRT）是研究铸铁应力腐蚀的有效方法。     

Erosion–corrosion assessment of materials for use in the resources industry

The erosion–corrosion properties of a range of ferrous-based materials that are currently being used or have potential for use in the resources industry have been assessed using a slurry pot erosion–corrosion (SPEC) test rig that has the capability of establishing the separate components of erosion, corrosion and synergy.Testing was performed, at 30 °C, in an aqueous slurry containing 35 wt% AFS 50–70 silica sand and a 3.5 wt% NaCl solution. Erosive action was supplied through high-speed rotation of a rubber-lined impeller.Erosion–corrosion performance of materials evaluated was related to composition/microstructure and hardness. Test data correlated with available service experience.The results showed that the cast Cr white irons with (i) a structure that was essentially a duplex stainless steel containing a distribution of hard carbides and (ii) a near eutectic Cr white iron exhibited the highest erosion–corrosion resistance of the materials tested. The evaluation of the Cr white irons also highlighted the influence of Cr and C levels on the E–C properties of these materials.E–C assessment of selected carbon steels confirmed that the erosion-only rates and synergistic levels showed a general decline with increasing carbon content and hardness. As expected, a low C steel pipe product displayed very mediocre erosion–corrosion behaviour as a consequence of its very low intrinsic corrosion resistance and inferior wear properties. This reflected service experience, however, such products are still being used, due to the comparatively low initial cost.A TiC particle-reinforced AISI 316 stainless steel exhibited an almost 45% improvement in the E–C resistance, when compared with an AISI 316L stainless steel.     

Effect of structural features on erosion resistance of cast irons

Erosion resistance of four types of cast iron of different microstructures and graphite morphologies (viz., grey cast iron, compacted graphite iron, spheroidal graphite iron and austempered ductile iron) was evaluated in three different erosive media. Results indicate that austempered ductile iron has the highest erosion resistance in all three media, followed by spheroidal graphite iron, compacted graphite iron and grey cast iron, in that order. Graphite morphology has a significant effect on the erosion resistance of these irons in quartz-water and iron oxide-oil slurry. However, the matrix microstructure determines the erosion resistance of these irons in quartz-oil slurry. The parameter H/E (which is the ratio of the Brinell hardness number to Young's modulus of the material) has been found to be a good indicator of erosive wear in quartz-oil slurry.     

Corrosion and wear resistance characteristics of NiCr coating by laser alloying with powder feeding on grey iron liner

To reduce the mixed fuel induced excessive wear of the cast iron engine cylinder liners, research on laser alloying of NiCr alloy with powder feeding was performed to locally change both the composition and the microstructure of the liner. The research indicated that laser alloying of 75Ni25Cr on grey cast iron liner demonstrates sound alloying layers free of cracks and porosities. The microstructure of the alloyed layer is composed of pre-eutectic austenite and ledeburite. The alloying element Ni is mainly located in the austenite, while Cr is mainly in cementite. The average hardness is HV_0.2500. The corrosion resistance of the alloyed layers in diluted H₂SO₄ solution and NaOH solution is dramatically improved compared to the grey cast iron. The relative wear resistance of the laser-alloyed 75Ni25Cr layer is 4.34 times of that of the grey cast iron. The improvements on the corrosion and wear resistance of the cast iron are attributed to the composition and microstructure change by laser alloying of 75Ni25Cr. Laser alloying can be a good solution to improve wear and corrosion resistance of the grey iron liners in mixed fuel environment.     

Scouring erosion resistance of metallic materials used in slurry pump service

Low impact angle erosion resistance is a critical requirement of materials used in pumps, piping, valves, nozzles, cyclones and other components which transport and process most mineral slurries.The Coriolis method offers a suitable technique for assessing behavior under such scouring attack conditions. It is being used increasingly in support of the mining/mineral processing industry, to compare and discriminate between candidate materials and also assist in the development of new products and protection systems. The specific method used in the current study involves high velocity erosion with aqueous slurry containing 10 wt.% of AFS 50-70 silica test sand. This compares reasonably with the main, extremely abrasive solids constituent encountered in mining and processing oil sands deposits in northern Alberta, Canada. These are becoming a rapidly growing and critically important source of oil in North America.Abrasion resistant chrome white iron castings typically covered by the ASTM A532 standard, are used widely in slurry pump components particularly in oil sand operations. However, the development of proprietary cast hypereutectic chromium white irons with microstructures containing primary M₇C₃-type carbides, is providing the capability to significantly improve the wear performance of such parts. In certain applications where corrosion contributes significantly to overall attack, lower carbon and higher chromium-bearing variants are employed.A comparison of the Coriolis erosion behavior of a wide range of commercially available cast wear and corrosion resistant and high toughness alloys used in pump manufacture, has confirmed anticipated performance ranking and the superiority of the latest generation of hypereutectic chrome white irons. The ameliorative influence on scouring erosion behavior of high carbon content, hardness and carbide volume fraction and particularly of fine carbide size has been demonstrated. A correlation is drawn between test data and service performance.     

Effect of bulk heat treatment and plasma surface hardening on the microstructure and erosion wear resistance of complex-alloyed cast irons with spheroidal vanadium carbides

The results of an investigation of the effect of bulk quenching from temperature in the range of 760–1050°C, cryogenic treatment (–196°C) and surface plasma hardening on the abrasive-erosion wear of frugally alloyed V–Cr–Mn–Ni cast irons with spheroidal vanadium carbides have been presented in this article. It has been found that cast irons containing 5.0–7.5% V, 4.5–9.0% Cr, and 5.5–5.7% (total) of Mn and Ni after heat treatment have a 2–3-fold advantage in wear resistance compared to the prototype high-vanadium cast iron (11.9% V, 12.9% Mn). The maximum wear resistance of cast irons studied is achieved by quenching at 760°C followed by plasma surface hardening, as well as quenching at 840°C, followed by cryogenic treatment. These treatments result in the formation of an optimum microstructure that consists of spheroidal vanadium carbides, eutectic carbides M₇C₃, and a martensite-austenite matrix reinforced by secondary carbides. The increase in quenching temperature leads to an increase in the amount of residual austenite and decrease in the erosive wear resistance of cast irons.     

Untersuchungen über die beeinflussung des gefüges karbidischer gusseisen bei abrasiver verschleissbean-spruchung

In this paper the mechanism of abrasive wear of white cast irons is examined on the microstructural scale. The Fe-C-Cr-Mo, Fe-C-Cr-Ni and Fe-C-V-Cr alloys were tested. The results of the test have shown that abrasive wear of white cast iron is the result of wear of the microstructural components. Under high-stress abrasion the carbide can be deformed, scratched, broken and uprooted. The matrix shows cutting and deformation work hardening and martensitic transformation. The abrasion behaviour of alloys with different microstructural matrices is markedly influenced by mechanisms of wear. During abrasion the austenitic matrix can undergo the form, the hardness, the kinetic energy and the pressure of abrasive particles.     

Ball-cratering abrasion tests of high-Cr white cast irons

The application of a ball-cratering method to test three-body abrasive wear of bulk materials in the presence of large abrasive particles has been investigated. Three high-Cr white cast irons (WCIs) with different material properties were used as wear samples. Abrasive slurries contained two types of abrasive particles, silica sand and crushed quartz. Silica sand and crushed quartz particles have similar chemical composition and hardness but differ in sharpness. Wear rates of WCI samples were determined and the worn surfaces were examined by optical microscopy, SEM and Talysurf profilometry.It was found that the ball-cratering test can differentiate between the wear resistances of materials with similar properties. The wear resistance of WCIs in the presence of silica sand increased with increasing the hardness of the wear sample and decreasing the size of carbides in the microstructure. Smaller silica sand particles caused less wear damage than larger silica sand particles, even though the smaller particles were slightly sharper than the larger ones. When silica sand and quartz particles of the same size were used, the angular quartz particles caused much higher wear than the rounded silica sand particles. Surface morphologies of the wear craters on the WCI samples were examined in an SEM and then compared with the morphologies of the worn surfaces from slurry pumps. It was found that the silica sand particles generated surface morphologies similar to those found in the worn slurry pumps. In these surfaces the matrix was preferentially worn out and hard carbides were protruding. Wear surface morphologies produced by the angular quartz particles were different. They consisted of numerous superimposed indents and the microstructure phases were not distinguishable. This indicates that the type of abrasive particles used in ball-cratering testing significantly affects the test outcomes in terms of wear rates and wear surface morphology.     

灰铸铁表面原位合成TiC/Al3Ti复合涂层的组织及耐磨性

采用铸造反应合成技术在灰铸铁表面原位合成TiC/Al3Ti复合涂层材料,对复合涂层的显微组织、硬度和耐磨性进行了研究。结果表明:Al-Ti-C体系完全反应后可制备出纯净的TiC/Al3Ti表面复合涂层材料,该表面复合材料组织致密,并随着涂层中TiC含量的增加,材料的硬度有所提高,表面复合涂层的硬度明显高于铁基体的硬度,磨损性能也要优于铁基体,明显改善了铸铁的表面硬度和摩擦性能。       

Widerstand gegen abrasiven verschleiss und dynamische bruchzähigkeit weisser vanadingusseisen

The wear behaviour under abrasive sliding loading, the structure and dynamic fracture toughness of white cast iron containing (4 – 6)% V are considered in this paper. In wear systems containing hard abrasive particles (silicon carbide), the dynamic fracture toughness and wear resistance increase with increasing austenite content in the structure. In systems with less hard abrasive particles (e.g. flint, garnet) these alloys exhibit a combination of high fracture toughness and high wear resistance. The vanadium-alloyed white cast irons with a predominantly austenitic matrix show more favourable values with respect to both dynamic fracture toughness and wear resistance in comparison with a simultaneously tested chromium white cast iron.     

Sliding wear of graphite crystallized chromium white cast iron

The effects of sliding velocity, heat-treatment and graphite shape on sliding wear of graphite crystallized chromium white cast iron were studied. Two types of graphite crystallized chromium white cast irons having flaky or spheroidal and another type of 2.6C–15Cr white cast iron were prepared for this study. The effect of sliding velocity on wear resistance was studied by the Okoshi type and pin-on-disk type wear tests on materials which have experienced “as cast” and “heat-treated” conditions. The Okoshi type wear test results are divided into two relationships depending on sliding velocity or distance. Two regimes, initial wear and steady-state wear, existed for wear loss and sliding distance. A characteristic form of wear curve with a peak and a minimum was obtained when correlating wear loss and sliding velocity. The wear resistance of graphite crystallized chromium white cast irons were superior to that of 2.6C–15Cr white cast iron. In the results of pin-on-disk tests, there was no clear difference in the reported wear loss and friction coefficient among the alloys. However, an opposite tendency has appeared in the wear loss and friction coefficient: the wear loss value reached a peak in the wear curve at 0.52 m/s, while the friction coefficient reached a minimum at 0.52 m/s.     

Influence of graphite nodules on the particles erosion of spheroidal graphite cast irons

The influence of graphite nodules on the normal angle erosion of the spheroidal graphite cast irons with four different matrices, namely ferrite, upper bainite, lower bainite and martensite, was investigated. The results indicate that, in the range investigated (10-15 area pet), graphite nodules (with variations in area percent and size) did not exert any influence in the irons with ferrite or upper bainite matrix. However, in the case of the spheroidal graphite cast iron with martensitic matrix, both increasing area percent and decreasing diameter of graphite nodules did in fact raise the erosion rate; moreover, those cast in metal molds consistently experienced higher erosion rate than those cast in sand molds. For the irons with a lower bainite matrix, increasing the amount of graphite nodules raises the erosion rate for those cast in sand molds, but did not affect the erosion rate for those cast in metal molds; furthermore, the erosion rate of the sanded-molded irons was consistently higher than their metal molded counterparts. The different roles of graphite nodules on the erosion rates of the spheroidal graphite cast irons are discussed.     

Three-body impact wear study on conventional and new P/M + HIPed wear resistant materials

A new hammer-mill type impact wear testing facility was built for impact wear testing and characterization. Tests with the hammer-mill impact wear device were carried out on conventional wear resistant materials such as Mn-steels of different compositions, white cast iron, and on new P/M+HIPed wear resistant materials. To verify the validity in using this laboratory wear testing apparatus, wear behavior and worn surfaces obtained on conventional and new Mn-steels generated from this device were compared with wear phenomena and worn surfaces developed in industrial applications, i.e. from certain types of rock crushers. The strain hardening effect in different Mn-steel grades was studied first. Second, the wear resistance of materials with different properties was studied using two different grades of abrasive. With silica sand (high hardness, low compressive strength), conventional Mn-steel and white cast iron perform in a manner comparable with the P/M+HIPed materials. With volcanite sand (low hardness, very high compressive strength), the P/M+HIPed wear resistant materials appear to have the best wear resistance.     

A metallurgical evaluation of tool wear and chip formation when machining pearlitic grey cast irons with dissimilar graphite morphologies

The need for superior in-service strength has meant that an increasing number of engineering components are now being made from pearlitic cast irons containing spheroidal graphite, rather than the more traditional cast irons containing flake graphite. Such changes of workpiece material have resulted in a rapid decline in tool life in many machining operations, particularly turning and facing.An investigation into the factors involved during chip formation which result in the observed patterns of tool wear is described in the work presented here. A series of turning tests were made on pearlitic grey cast irons containing flake (GA iron) and spheroidal (SG iron) graphite morphologies with cemented carbide (coated and uncoated) and ceramic tool materials. Built-up edge persisted to higher cutting speeds when cutting SG iron than GA iron, its periodic detachment causing attrition or fracture of the cutting edge. Smooth wear processes, probably caused by dissolution-diffusion and small strain discrete plastic deformation, were predominant on the rake and flank faces of the coated and ceramic tools when cutting both cast irons at high speed. Smooth wear was less rapid when cutting GA iron than SG iron because tool temperatures were reduced and “protective” nonmetallic layers, deposited from the chip-workpiece, interrupted dissolution-diffusion. When cutting SG iron, rapid wear of the uncoated cemented carbides was caused by attrition, while the relatively slower smooth wear, when cutting GA iron, was caused by dissolution-diffusion.     

Erosion–corrosion performance of high-Cr cast iron alloys in flowing liquid–solid slurries

In many slurry transportation systems, such as in FGD (Flue Gas Desulphurization) and chemical processing applications, corrosion and erosion are the two main mechanisms of material degradation of the pump wet-end components including pump casing, impeller and liners. The performance of a selected material is mostly dependent upon its relative corrosion and erosion resistance to the service environment. In these cases erosion, corrosion and the related synergistic effects can be very complicated since they are affected by numerous factors including solid and slurry properties, chemical contents, hydraulic conditions and temperatures. In this experimental study, sliding Coriolis erosion testing has been performed with various corrosion factors such as pH value, chlorides content and temperature to evaluate the erosion–corrosion resistance of some high-alloyed white cast irons containing different levels of chromium and other elements. Optical microscope and SEM-EDS have also been used to examine microstructure and surface conditions of tested materials. Results indicated that material loss due to corrosion factors increased as acidity-chlorides and temperature increased. At relatively high corrosion intensity, the white cast irons with higher alloy content (especially chromium) clearly showed improved corrosion resistance and combined erosion–corrosion resistance over those with lower alloy content. Under certain corrosion and hydraulic conditions, particle size is perhaps the single most influential factor on erosion–corrosion rate of the high-Cr cast iron alloys. Relatively large particles are much more effective than small ones at removing both the corroded surface layer and the fresh material, causing substantially higher rate of material loss. Some other related factors have also been addressed.     

27%Cr高铬铸铁组织及性能研究

对不同碳、钼含量的27％高铬铸铁的组织、硬度及耐磨性等进行了试验。结果表明：高铬铸铁的淬火硬度及抗磨料磨损能力随含碳量增加而提高。但当铬、碳含量比低于7时,宏观硬度降低。钼对改变大量析出奥氏体的临界含碳量有一定影响,铬、碳含量比低于7时,加钼量不应低于2％。无论含钼或不合钼,过共晶高铬铸铁（3．7％C）抗磨料磨损能力均优于亚共晶高铬铸铁,冲击韧度与后者相近。