Structural, spectroscopic and dielectric investigations on Ba8Zn(Nb6−xSbx)O24 microwave ceramics

Ba₈Zn(Nb_6−xSb_x)O₂₄ (x = 0, 0.3, 0.6, 0.9, 1.2, 1.5, 1.8 and 2.4) ceramics were prepared through the conventional solid-state route. The materials were calcined at 1250 °C and sintered in the range 1400-1425 °C. The structure of the system was analyzed by X-ray diffraction, Fourier transform infrared and Raman spectroscopic methods. The theoretical and experimental densities were calculated. The microstructure of the sintered pellets was analyzed using scanning electron microscopy. The low frequency dielectric properties were studied in the frequency range 50 Hz-2 MHz. The dielectric constant (?_r), temperature coefficient of resonant frequency (τ_f) and the unloaded quality factor (Q_u) are measured in the microwave frequency region using cavity resonator method. The τ_f values of the samples reduced considerably with the increase in Sb concentration. The materials have intense emission lines in the visible region. The compositions have good microwave dielectric properties and photoluminescence and hence are suitable for dielectric resonator and ceramic laser applications.     

Influences of poling condition and sintering temperature on piezoelectric properties of (Na0.5Bi0.5)1 − xBaxTiO3 ceramics

The structure, ferroelectric characteristics and piezoelectric properties of (Na_0.5Bi_0.5)_1 − xBa_xTiO₃ (x = 0.04, 0.06, 0.10) ceramics prepared by conventional solid state method were investigated. The influences of poling condition and sintering temperature on the piezoelectric properties of the ceramics were examined. The piezoelectric properties of the ceramics highly depend on poling field and temperature, while no remarkable effect of poling time on the piezoelectric properties was found in the range of 5-25 min. Compared with (Na_0.5Bi_0.5)_0.96Ba_0.04TiO₃ and (Na_0.5Bi_0.5)_0.90Ba_0.10TiO₃, the piezoelectric properties of (Na_0.5Bi_0.5)_0.94Ba_0.06TiO₃ are more sensitive to poling temperature due to the relatively low depolarization temperature. Moderate increase of sintering temperature improved the poling process and piezoelectric properties due to the development of microstructural densification and crystal structure. With respect to sintering behavior and piezoelectric properties, a sintering temperature range of 1130-1160 °C was ascertained for (Na_0.5Bi_0.5)_0.90Ba_0.10TiO₃.     

Study on properties of BaxSmyTi7O20 ceramics with CaO-SiO2-B2O3 glass

The effect of CaO-SiO₂-B₂O₃ (CSB) glass addition on the sintering temperature and dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics has been investigated using X-ray diffraction, scanning electron microscopy and differential thermal analysis. The CSB glass starts to melt at about 970 °C, and a small amount of CSB glass addition to Ba_xSm_yTi₇O₂₀ ceramics can greatly decrease the sintering temperature from about 1350 to about 1260 °C, which is attributed to the formation of liquid phase. It is found that the dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics are dependent on the amount of CSB glass and the microstructures of sintered samples. The product with 5 wt% CSB glass sintered at 1260 °C is optimal in these samples based on the microstructure and the properties of sintering product, when the major phases of this material are BaSm₂Ti₄O₁₂ and BaTi₄O₉. The material possesses excellent dielectric properties: ?_r = 61, tan δ = 1.5 × 10⁻⁴ at 10 GHz, temperature coefficient of dielectric constant is −75 × 10⁻⁶ °C⁻¹.     

Influence of sintering temperature on piezoelectric properties of (K0.5Na0.5)NbO3-LiNbO3 lead-free piezoelectric ceramics

Lead-free piezoelectric ceramics (1 − x)(K_0.5Na_0.5)NbO₃-xLiNbO₃ have been synthesized by traditional ceramics process without cold-isostatic pressing. The effect of the content of LiNbO₃ and the sintering temperature on the phase structure, the microstructure and piezoelectric properties of (1 − x)(K_0.5Na_0.5)NbO₃-xLiNbO₃ ceramics were investigated. The result shows that the phase structure transforms from the orthorhombic phase to tetragonal phase with the increase of the content of LiNbO₃, and the orthorhombic and tetragonal phase co-exist in (K_0.5Na_0.5)NbO₃-LiNbO₃ ceramics when the content of LiNbO₃ is about 0.06 mol. The sintering temperature of (1 − x)(K_0.5Na_0.5)NbO₃-xLiNbO₃ decreases with the increase of the content of LiNbO₃. The optimum composition for (1 − x)(K_0.5Na_0.5)NbO₃-xLiNbO₃ ceramics is 0.94(K_0.5Na_0.5)NbO₃-0.06LiNbO₃. The optimum sintering temperature of 0.94(K_0.5Na_0.5)NbO₃-0.06LiNbO₃ ceramics is 1080 °C. Piezoelectric properties of 0.94 (K_0.5Na_0.5)NbO₃-0.06LiNbO₃ ceramics under the optimum sintering temperature are piezoelectric constant d₃₃ of 215 pC/N, planar electromechanical coupling factor k_p of 0.41, thickness electromechanical coupling factor k_t of 0.48, the mechanical quality factor Q_m of 80, the dielectric constant of 530 and the Curie temperature T_c = 450 °C, respectively. The results indicate that 0.94(K_0.5Na_0.5)NbO₃-0.06LiNbO₃ piezoelectric ceramics is a promising candidate for lead-free piezoelectric ceramics.     

Ferroelectric, dielectric and piezoelectric properties of Pb1?xCex(Zr0.60Ti0.40)O3, 0?≤?x?≤?0.08

The ferroelectric, dielectric and piezoelectric properties of compositions Pb_1−x Ce _x (Zr_0.60Ti_0.40)O₃, (x = 0.0, 0.01, 0.02, 0.04, 0.06 and 0.08) are studied. The above compositions are prepared from their constituent oxides, calcined at 900 °C for 4 h and various phases present are characterized by X-ray diffraction (XRD) technique. The above powders are uniaxially pressed into circular compacts, sintered at 1,250 °C for 2 h, electroded, poled at 2 kV/mm D.C. voltage and their electrical properties are measured. The XRD analysis shows the presence of rhombohedral phase up to 2 mol% ceria while tetragonal phase found at higher concentrations. It is observed that the ferroelectric, dielectric and piezoelectric properties increase with the addition of ceria with a maximum at 2 mol% and then decreases. The higher piezo properties associated with low ceria concentration are attributed to rhombohedral phase.     

Bismuth-modified BiScO3-PbTiO3 piezoelectric ceramics with high Curie temperature

New piezoelectric ceramics, 0.15BiScO₃-0.85(Pb_{1 − 3x / 2}Bi_x)(Ti_0.98Mn_0.02)O₃ (x = 0.04~0.10), were prepared by using conventional solid phase processing. The results of X-ray diffraction (XRD) show that the ceramics have a single phase tetragonal perovskite structure. The ceramics, poled by normal poling process, have piezoelectric coefficient d₃₃, planar electromechanical coupling factor kp and thickness electromechanical coupling factor k_t of 50~60 pC/N, ~ 11% and ~ 30%, respectively. An extremely high mechanical quality factor Q_m of 1540 was obtained at the composition x = 0.08. The Curie temperature (T_C) is in the range of 520-550 °C, higher than 490 °C of pure PbTiO₃. The combination of good piezoelectric properties and high T_C makes these ceramics suitable for elevated temperature piezoelectric devices.     

High piezoelectric d33 coefficient in (Ba1 − xCax)(Ti0.98Zr0.02)O3 lead-free ceramics with relative high Curie temperature

Lead-free (Ba_1 − xCa_x)(Ti_0.98Zr_0.02)O₃ (x = 0-0.04) ceramics were prepared successfully using a solid-state reaction technique. The polymorphic phase transitions (PPT) from orthorhombic to tetragonal phase around room temperature were identified in the composition range of 0 < x < 0.03. High piezoelectric coefficient of d₃₃ = 375 pC/N and planar electromechanical coupling factor of k_p = 44.1% were obtained for the samples at x = 0.01. With the increase of Ca content, the orthorhombic-tetragonal phase transitions shifted towards room temperature, while relative high Curie temperature (T_C) was still maintained about 115 °C.     

Microwave dielectric properties of Ba2 − xSrxLa3Ti3NbO15 ceramics

High dielectric constant and low loss ceramics in the system Ba_2 − xSr_xLa₃Ti₃NbO₁₅ (x = 0-1) have been prepared by conventional solid-state ceramic route. Ba_2 − xSr_xLa₃Ti₃NbO₁₅ solid solutions adopted A₅B₄O₁₅ cation-deficient hexagonal perovskite structure for all compositions. The materials were characterized at microwave frequencies. They show a linear variation of dielectric properties with the value of x. Their dielectric constant varies from 48.34 to 43.03, quality factor Q_u × f from 20,291 to 39,088 GHz and temperature variation of resonant frequency from 8 to 1.39 ppm/°C as the value of x increases. These low loss ceramics might be used for dielectric resonator (DR) applications.     

Different microstructure and dielectric properties of Ba1−xCaxTiO3 ceramics and pulsed-laser-ablated films

A comparative study of the microstructure and dielectric properties between Ba_1−xCa_xTiO₃ (BCT) ceramics and films were performed in the whole Ca concentration range of x = 0-1. The ceramics were prepared by conventional solid-state reaction technique and the films by the method of pulsed-laser deposition. X-ray diffraction (XRD) study of the BCT ceramics exhibited a pure tetragonal phase for x = 0-0.25, a tetragonal-orthorhombic diphase for x = 0.25-0.85 and a pure orthorhombic phase for x = 0.90-1.00. And the dielectric phase transition temperature from tetragonal to cubic was marginally affected by the Ca doping into BaTiO₃. However, BCT films deposited on Pt/Si/SiO₂/Si substrates showed a different microstructure and dielectric properties. Tetragonal-orthorhombic diphase was not found in the BCT films for x = 0.25-0.85, and a large decrease of the Curie point and diffuse phase transition were observed in the BCT films. Based on the compositional analysis, such phenomena were ascribed to the occupancy of some Ca²⁺ to the Ti⁴⁺ sites in the BCT films.     

Phase relations and microwave dielectric properties of vanadium modified Ba5Nb4O15 ceramics

Microwave dielectric ceramics of Ba₅Nb_4−xV_xO₁₅ (x = 0-1) were prepared by a solid-state reaction method. Vanadium substitution can markedly lower the sintering temperature of Ba₅Nb₄O₁₅ from 1450 to 1100 °C. The X-ray powder diffraction analysis reveals the multiphase nature of this system. A hexagonal-to-orthorhombic phase transition was also observed for the BaNb₂O₆ secondary phase. The microwave dielectric properties, such as τ_f, ε_r and Q × f value, decreased with increasing vanadium content for samples sintered at 1100 °C. There was an apparent increase in τ_f and Q × f value for samples (x ≥ 0.5) sintered at 1200 °C due to the hexagonal-to-orthorhombic phase transition of the BaNb₂O₆ phase. These results suggested that the microwave dielectric properties of multiphase ceramics strongly depended on the phase compositions and the phase transitions.     

Effect of BaTiO3 additive on the electrical properties of Na0.50Bi0.50TiO3 lead free ceramics

The near morphotropic phase boundary (MPB) compositions of lead-free piezoelectric ceramics based on sodium bismuth titanate (Na_0.50Bi_0.50TiO₃: NBT) and barium titanate (BaTiO₃: BT) were carefully investigated by conventional high temperature mixed-oxide method. All the ceramics exhibit single phase rhombohedral symmetry. The frequency (100 Hz to 1 MHz) and temperature (Room temperature–500 °C) dependence of impedance spectroscopy of (1 − x)Na_0.50Bi_0.50TiO3–xBaTiO₃ (x = 0.0, 0.06, 0.07 and 0.08) ceramics were investigated by impedance analyzer. The frequency explicit plots of Z″ versus frequency at various temperatures show peaks in the higher temperature range (>400 °C). The compounds show dielectric relaxation, which is found to be of non-Debye type and the relaxation frequency shifted to higher side with increase in temperature. The activation energy values obtained for different BT content suggest that the electrical conduction in NBT is mainly due to the mobility of the ionized oxygen defects.     

Effects of Ti on dielectric and piezoelectric properties of (Pb0.985La0.01)1+y(Nb1−yTiy)2O6 ceramics

Piezoelectric ceramics (Pb_0.985La_0.01)_1+y(Nb_1−yTi_y)₂O₆ (0 ? y ? 0.1) (PLNT) were fabricated by a conventional solid-state reaction method. The crystal structure and microstructures of specimens were investigated by X-ray diffraction (XRD) and scanning electron microscope (SEM). All PLNT ceramics sintered at temperatures from 1250 °C to 1290 °C are shown to be a single orthorhombic phase. The formation of orthorhombic phase is promoted by excess PbO existed in the Ti-bearing samples during calcination processing. The increasing of the tolerance factor due to substitution of Ti⁴⁺ for Nb⁵⁺ is also responsible for the stability of orthorhombic phase. The high density of ceramics (relative density >95%) with the equiaxed grains and a minor porosity have been obtained. The measurement of dielectric and piezoelectric properties of PLNT ceramics reveals that Ti reduces the dielectric loss (tan δ) and dielectric constant (ε_r) of PLNT ceramics, and enhances the piezoelectric constant (d₃₃) and Curie temperature (T_c). The optimum component with y = 0.075 possesses the excellent electrical properties: ε_r = 182, tan δ = 0.0018, d₃₃ = 84 pC/N and T_c = 564 °C.     

Synthesis, characterization, and dielectric properties of Ba(Ti1−xSnx)O3 nanopowders and ceramics

We prepared Ba(Ti_1−xSn_x)O₃ powders and ceramics by means of the sol-gel process, with dibutyltin dilaurate as the Sn precursor. The samples were characterized by means of Fourier-transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy, and scanning electron microscopy, and also determined the dielectric properties of the ceramics. The powders synthesized by means of the sol-gel process had a grain size on the nanometer scale, with the grains mainly composed of a cubic BaTiO₃ phase. Sn can disperse into BaTiO₃ more uniformly in the sol-gel technique using dibutyltin dilaurate as the Sn precursor. With increasing Sn concentration, the grain size of the Ba(Ti_1-xSn_x)O₃ ceramics increased and the maximum dielectric constant (?_max) first increased and then decreased. At a Sn concentration of 5 mol%, ?_max reached its maximum value (19,235).     

Dielectric properties of Ba(Ti1 − xZrx)O3 solid solutions

This paper reports the structural and dielectric properties of Ba(Ti_1 − xZr_x)O₃ (x = 0-0.3) ceramics. Single-phase solid solutions of the samples were determined by X-ray diffraction. Microscopic observation by scanning electron microscope revealed dense, single-phase microstructure with large grains (20-60 μm). The evolution of dielectric behavior from a sharp ferroelectric peak (for x ≤ 0.08) to a round dielectric peak (for 0.15 ≤ x ≤ 0.25) with pinched phase transitions and successively to a ferroelectric relaxor (for x = 0.3) was observed with increasing Zr concentration. Compared with pure BaTiO₃, broaden dielectric peaks with high dielectric constant of 25,000-40,000 and reasonably low loss (tanδ: 0.01-0.06) in the Ba(Ti_1 − xZr_x)O₃ ceramics have been observed, indicating great application potential as a dielectric material.     

Tantalum influence on physical properties of (K0.5Na0.5)(Nb1−xTax)O3 ceramics

Lead-free (K_0.5Na_0.5)(Nb_1−xTa_x)O₃ ceramics with x = 0.00-0.30 were prepared by the solid-state reaction technique. The effects of Ta on microstructure, crystallographic structure, phase transition and piezoelectric properties have been investigated. It has been shown that the substitution of Ta decreases Curie temperature T_C and orthorhombic-tetragonal phase transition temperature T_O-T, while increasing the rhombohedral-orthorhombic phase transition temperature T_R-O. In addition, piezoelectric activity is enhanced with the increase of Ta content. The ceramics with x = 0.30 have the high value of piezoelectric coefficient d₃₃ = 205 pC/N. Moreover, k_p shows little temperature dependence between −75° C and 75 °C, and d₃₃ exhibits very good thermal stability over the range from −196 °C to 75 °C in the aging test.     

Structure analysis on the Ba3Mg(Ta1−xNbx)2O9 ceramics: Coexistence of order and disorder

The Ba₃ZnTa₂O₉ (BZT) and Ba₃MgTa₂O₉ (BMT) ceramics, a family of A₃B²⁺B⁵⁺₂O₉ complex perovskites, are extensively utilized in mobile based technologies due to their intrinsic high unloaded quality factor, high dielectric constant and a low (near-zero) resonant frequency temperature coefficient at microwave frequencies. The preparation conditions as well as size and nature of B cations have a profound effect on the final dielectric properties. In this article, we report the effect of Nb⁵⁺ at the Ta⁵⁺ site on the BMT structure prepared at four synthesis temperatures (1300, 1400, 1500 and 1600 °C). The analysis has been carried out using the Rietveld technique on the X-ray powder diffraction data. Results suggest that both the preparation temperatures and Nb⁵⁺ content have significant effect on the ordering of B cations in the Ba₃Mg(Ta_1−xNb_x)₂O₉ solid solution. A disordered (cubic) structure is preferred by the 1300 °C compounds. The weight percentage of the ordered (trigonal) phase escalates, for a given composition, with increasing calcination temperature. A fully ordered trigonal arrangement exists only for x = 0.0 and 0.2 compounds calcined at 1600 °C, and the rest are biphasic (cubic and trigonal). The increase in the cubic fraction upon Nb⁵⁺ augmentation suggests that the solid solution leans more toward the disordered structural arrangement of B²⁺ and B⁵⁺ cations.     

Structural and dielectric properties of ferroelectric Sr1−xBaxBi2(Nb0.5Ta0.5)2O9 and Sr0.5Ba0.5Bi2(Nb1−yTay)2O9 ceramics

Ferroelectric Sr_1−xBa_xBi₂(Nb_0.5Ta_0.5)₂O₉ and Sr_0.5Ba_0.5Bi₂(Nb_1−yTa_y)₂O₉ were synthesized by solid state reaction route. X-ray diffraction studies confirm the formation of single phase layered perovskite solid solutions over a wide range of compositions (x=y=0.0, 0.25, 0.50, 0.75 and 1). The lattice parameters and the Curie temperature (T_c) have been found to have linear dependence on x and y. Transmission electron microscopy (TEM) suggest the lowering of orthorhombic distortion with increasing Ba²⁺ substitution. Variations in microstructural features as a function of x and y were monitored by scanning electron microscopy (SEM). The dielectric constant at room temperature increases with increase in both x and y. Interestingly Ba²⁺ substitution on Sr²⁺ site induces diffused phase transition and diffuseness increases with increasing Ba²⁺ concentration.     

Effect of BiFeO3 additions on the dielectric and piezoelectric properties of (K0.44Na0.52Li0.04)(Nb0.84Ta0.1Sb0.06)O3 ceramics

(1 − x) (K_0.44Na_0.52Li_0.04)(Nb_0.84Ta_0.1Sb_0.06)O₃ − x BiFeO₃ (x = 0, 0.002, 0.004, 0.006, 0.008, 0.01) lead-free piezoelectric ceramics were prepared by the conventional ceramic processing. The compositional dependence of the phase structure and the electrical properties of the ceramics were studied. A morphotropic phase boundary between the orthorhombic and tetragonal phases was identified in the composition range of 0.004 < x < 0.006. The ceramics near the morphotropic phase boundary exhibit a strong compositional dependence and enhanced piezoelectric properties. The ceramics with 0.6 mol.% BiFeO₃ exhibit good electrical properties (d₃₃ ∼ 246 pC/N, k_p ∼ 43%, T_c ∼ 285 °C, ?_r ∼ 1871, and tan δ ∼ 1.96%). These results show that the (1 − x) (K_0.44Na_0.52Li_0.04)(Nb_0.84Ta_0.1Sb_0.06)O₃ − x BiFeO₃ ceramic is a promising lead-free piezoelectric material for applications in different devices.     

Preparation, structure and dielectric properties of Ba4LaMNb3O15 (M = Ti, Sn ) ceramics

Two new cation-deficient hexagonal perovskites Ba₄LaMNb₃O₁₅ (M = Ti, Sn) ceramics were prepared by high temperature solid-state reaction route. The phase and structure of the ceramics were characterized by X-ray diffraction, scanning electron microscopy (SEM). The microwave dielectric properties of the ceramics were studied using a network analyzer. The Ba₄LaTiNb₃O₁₅ has high dielectric constant of 52, high quality factors (Q) 3500 (at 4.472 GHz), and temperature variation of resonant frequency (τ_f) +93 ppm °C⁻¹ at room temperature; Ba₄LaSnNb₃O₁₅ has dielectric constant of 39 with high Q value of 2510 (at 5.924 GHz), and τ_f −29 ppm °C⁻¹.     

Dielectric, ferroelectric and piezoelectric properties of Bi0.5Na0.5TiO3-(Ba0.7Ca0.3)TiO3 ceramics at morphotropic phase boundary composition

(1 − x)Bi_0.5Na_0.5TiO₃-x(Ba_0.7Ca_0.3)TiO₃ (BNT-xBCT, 0 ≤ x ≤ 0.15) solid solutions have been synthesized by a conventional solid state sintering method for obtaining a morphotropic phase boundary (MPB) with good piezoelectric properties. X-ray diffraction patterns reveal that a MPB of rhombohedral and tetragonal phases is formed at compositions 0.09 ≤ x ≤ 0.12. Addition of BCT into BNT greatly lowered coercive field E_c without degrading remanent polarization P_r. The specimen with x = 0.09 has the good piezoelectric properties: d₃₃ = 125 pC/N and k_p = 0.33. A modified Curie-Weiss law was used to fit the dielectric constant of BNT-xBCT ceramics, and a frequency dispersion was observed during the phase transitions from antiferroelectric to paraelectric in specimens with x exceeding 0.06.