金属网表面ZnO纳米棒的可控制备及其光催化性能

采用晶种诱导法,以硝酸锌为前驱体在金属网表面成功制备ZnO纳米棒光催化材料,用XRD、SEM等进行表征,并采用甲基橙溶液模拟废水,研究该材料的光催化降解性能。探讨了水浴合成ZnO纳米棒时,生长液浓度、反应温度等因素对光催化性能的影响。结果表明,80℃水浴反应4h,生长溶液浓度为100mmol/L,制备得到的ZnO纳米棒光催化活性较佳,光催化反应2h甲基橙溶液的降解率可达99%。     

ZnS/ZnO纳米片组装的多孔微球的制备及光催化性能研究

将水热法制备的ZnS纳米球500℃下保温2h制备出由ZnS、ZnO纳米片组装的多孔微球。利用扫描电子显微镜、X射线衍射仪、透射电子显微镜、紫外-可见近红外分光光度计和紫外-可见分光光度计等对样品的形貌、结构和光学性能进行了表征。以甲基橙(MO)的光催化降解为目标反应,评价其光催化活性。ZnS/ZnO异质结材料的带隙明显窄于ZnO,光催化活性得到提高;经60 min紫外光照射后,ZnS/ZnO异质结催化剂对MO的降解率为76%。最后分析和探讨了异质结催化剂的光催化机理。     

掺铁纳米氧化锌的制备及其光催化性能

采用共沉淀法制备了纯纳米ZnO和掺铁纳米ZnO,并用X射线衍射光谱进行了表征。用紫外灯作为光源,甲基橙溶液为光催化反应模型降解物,研究了ZnO及掺铁ZnO的光催化性能,并考察了前驱体焙烧温度、铁掺杂量、底物浓度、光照时间以及pH对降解率的影响。结果表明,掺杂铁离子提高了ZnO的光催化活性,400℃热处理的掺杂铁0.5%(质量比)的ZnO的光催化性能最好;当甲基橙初始浓度为5mg/L,光照时间3h,掺杂铁0.5%(质量比)的ZnO粉末对甲基橙的降解率达到84%;掺铁纳米ZnO在弱酸性条件下的催化效果比碱性条件下更好。     

纵向多孔及实心ZnO微纳米棒的制备、表征及其光催化性能研究

以硝酸锌和六次甲基四胺为原料,水为溶剂,采用低温水热法制备出具有优异光催化性能的六方纤锌矿结构ZnO微纳米棒,并研究了合成过程中磁力搅拌及原料溶液浓度对制备产物形貌及光催化性能的影响,建立了其光催化降解甲基橙的动力学方程。结果表明,搅拌条件下制备的产物为纵向多孔的棒状ZnO,无搅拌条件下制备的产物为实心ZnO纳米棒.优选出的硝酸锌和六次甲基四胺浓度均为0.025mol/L。相比于实心ZnO纳米棒,纵向多孔的棒状ZnO具有更优异的光催化性能,在紫外光照射20min后,对甲基橙的降解率达到100%。通过动力学模型拟合发现,纵向多孔的棒状ZnO具有更大的催化速率常数(0.2942 min~(-1)),是实心ZnO纳米棒催化速率常数(0.1306min~(-1))的2.25倍。     

掺杂元素对非晶态纳米二氧化钛光催化性能的彤响

采用溶胶-凝胶法将不同元素转入二氧化钛结构之中,分析元素掺杂对非晶态TiO2颗粒光催化性能的影响。以甲基橙溶液模拟目标污染物,用紫外-可见分光光度计测定甲基橙溶液光照前后吸光度的变化,结果表明,掺杂元素后的非晶态TiO2与未掺杂的纳米TiO2相比具有更好的光催化活性,其中,金属元素FeN最佳掺杂量为1．5％,降解率达到73．02％;稀土元素Ce的最佳掺杂量为1．5％,降解率达到73．33％;非金属元素SN最佳掺杂量为2．5％,降解率达到94．13％。     

TiO2负载ZnO纳米棒的制备及其光催化性能

采用水热法制备ZnO纳米棒,将TiO2溶胶高速旋涂在ZnO纳米棒的表面,得到TiO2/ZnO复合半导体。通过扫描电子显微镜(SEM)、X射线衍射(XRD)及UV-Vis漫反射等研究样品的表面形貌、晶型结构及光学特性。结果表明:375℃高温焙烧后,TiO2生长成颗粒状,均匀负载在ZnO纳米棒的表面,样品对紫外-可见光的吸收增强。以甲基橙溶液为模拟废水在紫外光辐照下的降解率来评价样品的光催化性能,结果显示,两种半导体复合以后,对光的利用率提高,对甲基橙模拟废水的降解率高于单一半导体。     

RGO/ZnO纳米棒复合材料的合成及光催化性能

采用水热合成法制备ZnO纳米棒及RGO/ZnO纳米棒复合材料。研究不同含量的RGO对RGO/ZnO纳米棒复合材料光催化活性的影响。采用X射线衍射仪(XRD)、场发射电子显微镜(FESEM)、光电子能谱仪(XPS)及漫反射紫外-可见吸收光谱(UV-Vis)检测手段对RGO/ZnO进行表征。结果显示:RGO与ZnO纳米棒成功复合。加入GO的含量不同,获得的RGO/ZnO样品在可见光区域的吸光度值不同。以甲基橙作为模拟污染物的光催化结果表明,RGO/ZnO复合材料具有高的紫外-可见光光降解效率,加入GO与ZnO的质量比为3%时,样品紫外-可见光光催化性能最佳,120min内甲基橙基本可以完全降解;且在波长大于400nm可见光照射下,RGO/ZnO具有一定的可见光活性,180min内其降解甲基橙效率最大可达26.2%。同时,RGO/ZnO具有较好的光稳定性。     

Ce掺杂ZnO分级结构微球的制备及其光催化性能研究

以硝酸锌、氢氧化钠、硝酸铈为原料,采用沉淀法制备了一系列Ce掺杂的Ce/ZnO分级结构微球。采用X射线衍射仪、场发射扫描电子显微镜、能量色散谱仪和紫外-可见漫反射光谱仪等对样品进行表征。以甲基橙的光催化降解为模拟反应,考察了Ce掺杂量对Ce/ZnO分级结构微球光催化性能的影响。结果表明:Ce/ZnO分级结构微球由ZnO微纳米片相互交错构建而成,Ce的掺杂提高了Ce/ZnO分级结构微球的光催化活性,其中Ce摩尔分数为1.5%的Ce/ZnO对甲基橙的光催化降解效果最好,紫外光照射60min甲基橙降解率为98.3%,循环使用4次,其催化活性未明显下降。     

纳米氧化锌光催化剂的制备及性能研究

以乙酸锌和氨水为反应物,采用简单水热法合成了纳米氧化锌(ZnO)光催化剂,通过FT-IR、XRD、UV-Vis、SEM等测试技术对样品进行表征。以甲基橙溶液为目标降解物,在500W汞灯照射下对甲基橙溶液进行光催化降解实验。结果表明,通过该方法合成的纳米ZnO为六方晶系结构,结构清晰,尺寸均匀,对甲基橙溶液具有良好的光催化性能。同时,对纳米ZnO光催化材料未来的发展趋势进行了展望。     

ZnO/Ag/CdCO_3纳米复合光催化剂的制备及性能研究

采用配位均匀共沉淀法制备出ZnO/Ag/CdCO3纳米复合光催化剂,用TEM、XRD、FT-IR、ICP等对产物的形貌、微观结构及组成进行了表征,着重研究了反应物配比及Cd(NO3)2浓度对ZnO/Ag/CdCO3纳米复合光催化剂催化降解甲基橙光催化活性的影响规律,结果表明,n(Zn2+):n(Ag+):n(Cd2+)=21:1.76:1.75,Cd(NO3)2浓度为0.168mol·dm-3时制得的纳米复合光催化剂对甲基橙(MO)的降解率较ZnO/Ag提高51%,ZnO/Ag/CdCO3对MO的光催化降解符合一级反应动力学方程,表观速率常数为1.4551h-1,是ZnO/Ag的7倍。     

不同合成过程对溶胶-凝胶法制备的ZnO/Ag纳米复合材料光催化性能的影响

以乙酸锌、硝酸银为前驱体,二乙醇胺作为稳定剂,利用溶胶-凝胶法分别采用一步法和两步法制备得到ZnO以及ZnO/Ag纳米复合粉体。所有ZnO/Ag复合物中Ag的含量均为3%(摩尔分数)。对所制备样品的结构和光学性质通过XRD、SEM、TEM、XPS、PL、UV-vis进行了表征,进而以甲基橙为模拟污染物进行了光催化测试。结果表明,不同方法制备得到的ZnO/Ag纳米粉体晶粒均匀,无明显团聚现象,面心立方结构的金属Ag吸附在纤锌矿结构的ZnO表面形成异质结。与纯ZnO相比,掺Ag极大地改善了样品在紫外光下的光催化活性。对不同合成工艺的比较表明,用溶胶-凝胶一步法制备的ZnO/Ag复合物的光催化活性最高,经紫外光照射70min可完全降解甲基橙。     

Ce掺杂TiO2薄膜电极光电催化降解甲基橙

用溶胶-凝胶法制备了泡沫镍负载TiO2及Ce离子掺杂TiO2薄膜电极,并以其为工作电极,建立了三电极光电催化体系。通过对水溶液中甲基橙的降解实验,考察了催化剂热处理温度、涂敷层数、外加电压、铈掺杂等因素对薄膜催化剂光催化性能的影响,结果表明,泡沫镍是光催化剂的优良载体;经500℃处理所得催化剂主要为锐钛矿相,催化活性最好;外加适当电压,有助于光催化降解;Ce的掺杂有易于TiO2催化活性的改善;外加适当电压有助于甲基橙的光催化降解。研究证明,500℃为铈掺杂TiO2薄膜的最佳热处理温度,外加一定电压、涂敷3层、掺杂n(Ce)/n(Ti)=2%的铈时催化剂的活性最高。     

Comparison of dye degradation efficiency using ZnO powders with various size scales

ZnO powders with various size scales (mean diameter size: 10, 50, 200 and 1000nm) have been prepared by two different preparation methods, thermal evaporation method and chemical deposition method, and examined as photocatalysts for the UV-induced degradation of methyl orange in water solution. ZnO nanoparticle with diameter size 50nm prepared by thermal evaporation method showed the highest photocatalytic activity. In addition, the tetrapod ZnO nanopowders had the higher efficiency than irregular ZnO particles. However, the smallest 10nm ZnO nanoparticle prepared by chemical deposition method indicated the lower efficiency contrast to 200nm ZnO powders prepared by thermal evaporation method. The results indicated preparation method was the decisive factor rather than size and morphology. Moreover, the effect of catalyst loading, pH value and the initial dye concentration on the final degradation efficiency were discussed through the photocatalytic experiments using 50nm ZnO nanoparticle as photocatalyst.     

燃料对溶液燃烧合成ZnO纳米棒微观形貌和光催化性能的影响

以蔗糖、柠檬酸、乙二醇和尿素为燃料, Zn(NO₃)₂为氧化剂/锌源, 采用溶液燃烧法合成ZnO纳米棒。借助XRD、SEM、比表面分析和光谱吸收等测试方法, 考察了不同燃料对粉体的物相组成、微观形貌、比表面积和光催化性能的影响。结果表明: 在点燃温度500℃下, 各燃料配制的前驱体溶液均可发生燃烧反应合成六方相ZnO纳米棒, 其平均径向尺寸小于100 nm, 且以尿素为燃料合成的ZnO晶形更完整, 以蔗糖为燃料合成的ZnO粉体具有最大的比表面积(24.83 m²/g)。光催化实验表明, 以蔗糖为燃料合成的ZnO粉体光催化能力最佳, 在高压汞灯照射60 min条件下, 其对甲基橙溶液(10 mg/L)的降解率可达98.2%, 且光催化反应符合一级动力学方程。     

Enhanced visible-light-responsive photocatalytic property of CdS and PbS sensitized ZnO nanocomposite photocatalysts

CdS and PbS nanoparticles sensitized ZnO nanorods were synthesized by successive ionic layer adsorption and reaction method. The photocatalytic activity of different structures was evaluated by photocatalytic degeneration yield of methyl orange. Co-sensitization of CdS and PbS nanoparticles on ZnO nanorods showed enhanced photocatalytic activity due to its response at visible light area and the stepwise band gap constructed in ZnO/CdS/PbS nanostructures.     

TiO2负载硅铝陶瓷介孔球对甲基橙吸附和光催化 降解的研究

：以自制硅铝陶瓷介孔球为基体,经溶胶凝胶法制备TiO2溶胶并将其负载于硅铝陶瓷介孔球表面,用于甲基橙溶液的吸附和光催化降解,再利用扫描电子显微镜、X射线衍射仪、傅里叶变换红外光谱仪和可见分光光度计对样品的表观形貌、晶体结构、吸附和光催化性能等进行表征和测定。研究结果表明：TiO2是以粗糙度较高的多层膜包覆于硅铝陶瓷介孔球表面且TiO2为锐钛矿晶型;在黑暗条件下,硅铝陶瓷介孔球和TiO2负载硅铝陶瓷介孔球对甲基橙仅起到吸附作用,且两者的吸附性能较接近;但在紫外光照条件下,TiO2负载硅铝陶瓷介孔球对甲基橙除有吸附作用外还表现出较好的光催化降解活性。     

Photocatalytic paper using zinc oxide nanorods

Zinc oxide (ZnO) nanorods were grown on a paper support prepared from soft wood pulp. The photocatalytic activity of a sheet of paper with ZnO nanorods embedded in its porous matrix has been studied. ZnO nanorods were firmly attached to cellulose fibers and the photocatalytic paper samples were reused several times with nominal decrease in efficiency. Photodegradation of up to 93% was observed for methylene blue in the presence of paper filled with ZnO nanorods upon irradiation with visible light at 963 Wm^–2 for 120 min. Under similar conditions, photodegradation of approximately 35% was observed for methyl orange. Antibacterial tests revealed that the photocatalytic paper inhibits the growth of Escherichia coli under room lighting conditions.     

Enhanced photocatalytic activity of ZnO/CuO nanocomposite for the degradation of textile dye on visible light illumination

The photocatalytic degradation of organic dyes such as methylene blue and methyl orange in the presence of various percentages of composite catalyst under visible light irradiation was carried out. The catalyst ZnO nanorods and ZnO/CuO nanocomposites of different weight ratios were prepared by new thermal decomposition method, which is simple and cost effective. The prepared catalysts were characterized by different techniques such as X-ray diffraction, transmission electron microscopy, field emission scanning electron microscopy, Fourier transform infrared spectroscopy and UV–visible absorption spectroscopy. Further, the most photocatalytically active composite material was used for degradation of real textile waste water under visible light illumination. The irradiated samples were analysed by total organic carbon and chemical oxygen demand. The efficiency of the catalyst and their photocatalytic mechanism has been discussed in detail.